VLSI and Circuits, Embedded and Hardware Systems Commons^™

Design Of A Bandgap Voltage Reference, Nicolaus Vail

Electrical Engineering Undergraduate Honors Theses

This thesis details the design process of a bandgap voltage reference (BGR) integrated circuit in a 180 nm CMOS process. A BGR provides a constant DC voltage across a range of operating temperatures and supply voltages. By its nature, the circuit is intended as a reference, not to provide current, so the output would be connected to a very high impedance, such as the gate of a transistor. At 27°C, this design provides a 955 mV reference voltage given a nominal VDD of 3 V. From 20°C to 175°C, the output voltage has a variance of 7.2 mV (approximately 0.8%) …

Photoassisted Nanoscale Memory Resistors, Amir Shariffar

Graduate Theses and Dissertations

Memristors or memory resistors are promising two-terminal devices, which have the potential to revolutionize current electronic memory technologies. Memristors have been extensively investigated and reported to be practical devices, although they still suffer from poor stability, low retention time, and laborious fabrication processes.

The primary aim of this project was to achieve a device structure of quantum dots or thin films to address a fundamental challenge of unstable resistive switching behavior in memristors. Moreover, we aimed to investigate the effects of light illumination in terms of intensity and wavelength on the performance of the fabricated memristor. The parameters such as …

Automatic Testing Of Organic Strain Gauge Tactile Sensors., Brian P. Goulet

Electronic Theses and Dissertations

Human-Robot Interaction is a developing field of science, that is posed to augment everything we do in life. Skin sensors that can detect touch, temperature, distance, and other physical interaction parameters at the human-robot interface are very important to enhancing the collaboration between humans and machines. As such, these sensors must be efficiently tested and characterized to give accurate feedback from the sensor to the robot. The objective of this work is to create a diversified software testing suite that removes as much human intervention as possible. The tests and methodology discussed here provide multiple realistic scenarios that the sensors …

Framework Of Hardware Trojan Detection Leveraging Structural Checking Tool, Rafael Dacanay Del Carmen

Graduate Theses and Dissertations

Since there is a significant demand for obtaining third-party soft Intellectual Property (IP) by first-party integrated circuit (IC) vendors, it is becoming easier for adversaries to insert malicious logic known as hardware Trojans into designs. Due to this, vendors need to find ways to screen the third-party IPs for possible security threats and then mitigate them. The development of the Structural Checking (SC) tool provides a solution to this issue. This tool analyzes the structure of an unknown soft IP design and creates a network of all the signals within the design and how they are connected to each other. …

Incorporating In Situ Measurements Of Energy Into A Designed Method Of Detection Of Radiation Induced Degradation In Embedded Systems, Delwyn Sam

Honors Theses

An embedded system, or a system-on-chip (SOC), is a miniaturized computer that combines hardware and software to accomplish a certain purpose. Embedded systems are used in various applications from household appliances to the automobile industry. Additionally, SOCs are used in space environments where the surroundings consist of radiation and extreme temperatures. In these harsh conditions, embedded systems must operate properly through the effects of radiation such as total ionizing dose (TID). Because embedded systems are filled with various components and modules, and since the internal signals of the system are often inaccessible, methods to locate which specific parts of the …

Junction Temperature Estimation Of Silicon Carbide Power Module Using Internal Gate Resistance As Temperature Sensitive Electrical Parameter, Michael Sykes

Graduate Theses and Dissertations

The junction temperature of a power module is measured non-intrusively and uninterrupted in its application by analyzing the dependency of gate resistance to temperature. The circuit configuration proposed consists of altering the gate loop path and adding a basic peak detection circuit with an added low-pass filter to accurately measure the small differences seen during a temperature change on the internal gate resistance. The testing on this Silicon Carbide power module shows that the internal gate resistance has a positive temperature coefficient. This causes the current and the voltage drop on the gate loop sensing resistance to reduce as the …

Design & Analysis Of Mixed-Mode Integrated Circuit For Pulse-Shape Discrimination, Bryan Orabutt

McKelvey School of Engineering Graduate Student Theses & Dissertations

In nuclear science experiments it is usually necessary to determine the type of radiation, its energy and direction with considerable accuracy. The detection of neutrons and discriminating them from gamma rays is particularly difficult. A popular method of doing so is to measure characteristics intrinsic to the pulse shape of each radiation type in order to perform pulse-shape discrimination (PSD).

Historically, PSD capable systems have been designed with two approaches in mind: specialized analog circuitry, or digital signal processing (DSP). In this work we propose a PSD capable circuit topology using techniques from both the analog and DSP domains. We …

Combat Robot, Wayne Lambert, Elijah Harris, Brian Eiseman, Jordan Meyer

ONU Student Research Colloquium

The senior capstone project that was tasked to the team was the decision of choosing a challenge within a national robotics competition. The group decided to compete at the National Robotics Challenge in Marion, Ohio. The idea was to participate in the combat robot competition at this NRC event. Once this decision had been made the next steps were to get an idea of what the rules and requirements of the competition were and to try and to sketch a very rough drawing of what the ideal robot should look like. From there it was decided to start a timeline …

Single Event Transient Sensitivity Measurement And Worst-Case Test Vector Exploration For Asic Devices Exposed To Space Single Event Environment, Mohamed Wael

Theses and Dissertations

Space radiation and nuclear reactors produce single event effects (SEE) in electronic circuits and impact their performance. The SEE phenomena cause circuits and electronic devices to fail by producing faulty results. Therefore, today’s circuit’s reliability is a significant concern for all circuit designers.

This thesis suggests a new automated flow to measure the single-event-transient (SET) effects in combinational circuits in application-specific integrated circuits (ASIC) while reaching full fault coverage. The developed flow characterizes the whole circuit nodes by identifying the most sensitive paths to the propagated SET pulses from the node under test to an observable primary output, causing single …

Modeling And Control Of Direct-Conversion Hybrid Switched-Capacitor Dc-Dc Converters, Ziyu Xia

Dartmouth College Ph.D Dissertations

Efficient power delivery is increasingly important in modern computing, communications, consumer and other electronic systems, due to the high power demand and thermal concerns accompanied by performance advancements and tight packaging. In pursuit of high efficiency, small physical volume, and flexible regulation, hybrid switched-capacitor topologies have emerged as promising candidates for such applications. By incorporating both capacitors and inductors as energy storage elements, hybrid topologies achieve high power density while still maintaining soft charging and efficient regulation characteristics. However, challenges exist in the hybrid approach. In terms of reliability, each flying capacitor should be maintained at a nominal `balanced' voltage …

The Design Of Cmos Front-End Amplifiers For Electrical Impedance Applications, Yueh-Ching Teng

Dartmouth College Ph.D Dissertations

Electrical Impedance Tomography (EIT) is a medical imaging methodology that does not need any kind of ionizing radiation. It is significantly cheaper and smaller than Computerized Tomography (CT) or Magnetic Resonance Imaging (MRI). These advantages make EIT particularly suitable for emerging applications like the continuous medical imaging and telemonitoring of organ function. Current bench-top EIT systems are bulky and require shielded cables to interface with measurement electrodes. The cable introduces parasitic capacitances which shunt the desired signals and degrade the accuracy of the measurements. A EIT system based on application-specific integrated circuits (ASICs) can reduce the parasitic and stray capacitance …

Autonomous Coffee Brewing System, Lillian Gonzalez, Landon Miller, Tyler Moff, Benjamin Vitu

Williams Honors College, Honors Research Projects

Coffee consumers want an affordable, high-quality cup of coffee that takes minimal time to brew and does not excessively contribute plastic to landfills. A fully autonomous system which utilizes whole coffee beans, water, and filters to brew coffee was designed to meet this need. This system accepts user requests which specify the brew’s portion size, water temperature, and brew strength, as well as the time which the system should begin the brewing process. Occasional maintenance to empty the system’s built-in waste receptacle or resupply the system with water, coffee beans, or filters is the only user intervention required. This report …

Smart Bike Aftermarket System (Sbams), Noah Lamadanie, Jack Bullock, Dawson Beachy, John Albrecht

Williams Honors College, Honors Research Projects

The Smart Bike Aftermarket System will be a set of connected modules, which, when installed on a standard bicycle, will allow it to mimic some of the safety and quality-of-life functionalities of an E-bike. The most notable of these safety features is an ability to detect vehicles approaching from behind and alert the user of potential collisions. The system will also implement lighting (Headlights, taillights, and turn signals), and a coupled application so a user can view more advanced information about their cycling. The primary advantage of this system over a standard E-bike is that it will have a lower …

Energy-Efficient And Secure Hardware Using Adiabatic Logic And Non-Volatile Mtj Devices, Zachary Kahleifeh

Theses and Dissertations--Electrical and Computer Engineering

Internet of Things (IoT) is a collection of devices that exchange data through a network to implement complex applications. IoT devices increase the quality of life of their user base which has a wide variety such as the medical field, consumer electronics, and the manufacturing sector. However, IoT devices have several challenges that need to be overcome namely, security and energy consumption. The threat vector that IoT devices face is growing and includes the following threats, the leakage of information through a side-channel attack known as the Correlation Power Analysis (CPA), authentication, piracy, etc. A side-channel attack is an attack …

Machine Learning Approach To Stability Analysis Of Semiconductor Memory Element, Ravindra Thanniru, Gautam Kapila, Nibhrat Lohia

SMU Data Science Review

Memory stability analysis traditionally relied heavily on circuit simulation-based approaches that run Monte Carlo (MC) analysis over various manufacturing and use condition parameters. This paper researches application of Machine Learning approaches for memory element failure analysis which could mimic simulation-like accuracy and minimize the need for engineers to rely heavily on simulators for their validations. Both regressor and classifier algorithms are benchmarked for accuracy and recall scores. A high recall score implies fewer escapes of fails to field and is the metric of choice for comparing algorithm. The paper identifies that recall score in excess of 0.97 can be achieved …

Design, Extraction, And Optimization Tool Flows And Methodologies For Homogeneous And Heterogeneous Multi-Chip 2.5d Systems, Md Arafat Kabir

Graduate Theses and Dissertations

Chip and packaging industries are making significant progress in 2.5D design as a result of increasing popularity of their application. In advanced high-density 2.5D packages, package redistribution layers become similar to chip Back-End-of-Line routing layers, and the gap between them scales down with pin density improvement. Chiplet-package interactions become significant and severely affect system performance and reliability. Moreover, 2.5D integration offers opportunities to apply novel design techniques. The traditional die-by-die design approach neither carefully considers these interactions nor fully exploits the cross-boundary design opportunities.

This thesis presents chiplet-package cross-boundary design, extraction, analysis, and optimization tool flows and methodologies for high-density …

Indoor Positioning Using Synchronized Ultrasonic Ofdma Signals, Julian Bartolone

Master's Theses

This paper proposes a method of short-range indoor localization using differential phase measurements of synchronized two-tone ultrasonic signals in an Orthogonal Frequency Multiple Access (OFDMA) scheme. This indoor positioning system (IPS) operates at an ultrasonic frequency of approximately 40kHz and synchronizes using an infrared signal. The OFDMA scheme allows for a receiver to process the signals from multiple transmitters continuously without the signals interfering with each other. The phases of the signals are measured using Goertzel Filters, allowing for low-complexity frequency content analysis. A MATLAB simulation using the proposed localization method is performed using four transmitter nodes in the corners …

Creating Reel Designs: Reflecting On Arthrogryposis Multiplex Congenita In The Community, Iris Layadi

Purdue Journal of Service-Learning and International Engagement

Because of its extreme rarity, the genetic disease arthrogryposis multiplex congenita (AMC) and the needs of individuals with the diagnosis are often overlooked. AMC refers to the development of nonprogressive contractures in disparate areas of the body and is characterized by decreased flexibility in joints, muscle atrophy, and developmental delays. Colton Darst, a seven-year-old boy from Indianapolis, Indiana, was born with the disorder, and since then, he has undergone numerous surgical interventions and continues to receive orthopedic therapy to reduce his physical limitations. His parents, Michael and Amber Darst, have hopes for him to regain his limbic motion and are …

Expanding Temperature Sensing For The Orion Bms 2, Samuel J. Parker

University Honors Theses

Formula SAE (FSAE) is an annual collegiate design competition that takes place across the globe. Portland State University’s team, Viking Motorsports, was committed to designing an Electric Vehicle (EV) for the 2021 FSAE competition. The team designed a completely custom lithium-ion cell battery that is managed by an Orion BMS 2 battery management system. The FSAE rulebook requires a robust temperature monitoring system for any EV power supply. The Orion BMS 2 can only directly collect data from eight temperature sensors, which is not enough to meet FSAE regulation. However, the BMS can be configured to monitor many more sensors …

A 12-Bit 1gs/S Sar-Assisted Pipeline Adc With Harmonic Injecting Residue Amplifier, Liang Fang

Electrical Engineering Theses and Dissertations

Advanced wireless applications require a medium resolution Radio Frequency (RF) sampling Analog to Digital Converter (ADC). By performing sampling of ADC at RF frequency, the mixer and Intermediate Frequency (IF) amplifier can be implemented in the digital domain, which helps the receiver eliminate troublesome mixing spurs and potentially improves the software-defined ratio of the entire system. By combing the merits of the energy-efficient Successive Approximation Register (SAR) ADC and the high-speed pipeline ADC, the SAR-assisted pipeline ADC achieves superior performance in high-speed medium-resolution ADC. However, with the advance of the process, due to the pure analog implementation, the residue amplifier …

Bibliometric Review Of Fpga Based Implementation Of Cnn, Priti Shahane, Piyush Tyagi, Purba Saha, Shravan Sainath, Swanand Bedekar

Library Philosophy and Practice (e-journal)

Nowadays Convolution Neural Network (CNN) has become the state of the art for machine learning algorithms due to their high accuracy. However, implementation of CNN algorithms on hardware platforms becomes challenging due to high computation complexity, memory bandwidth and power consumption. Hardware accelerators such as Graphics Processing Unit (GPU), Field Programmable Gate Array (FPGA), Application Specific Integrated Circuit (ASIC) are suitable platforms to model CNN algorithms. Recently FPGAs have been considered as an attractive platform for CNN implementation. Modern FPGAs have various embedded hardware and software blocks such as a soft processor, DSP slice and memory blocks. These embedded resources …

Reference Design Of An Online Emulation And Hot-Patching Approach For Power Electronic Controller Validation, Estefano Soria Pearson

Graduate Theses and Dissertations

This thesis aims to develop a reference design of an online security system approach embedded in a power electronic controller for cybersecurity purposes. Cybersecurity in power electronics focuses on reducing vulnerabilities in the system, where most reside in the communication with the hardware devices. Although methods to secure communications lessen the probability and effects of cyber-attacks, discovering vulnerabilities is inevitable. This thesis attempts to provide a fail-safe approach to securing the system by targeting the safety of the power-electronic controller. This approach applies an additional security layer in case of a malicious or accidental controller firmware malfunction.

The online security …

A Brief Bibliometric Survey On Night Vision Bot Using Dynamic Ir And Object Detection, Devesh Abhyankar Mr., Gurumoorty Suresh Mr., Hrithik Sambhaji Karjule Mr., Parth Bhardwaj Mr., Harish Muleva Mr., Anurag Mahajan Dr.

Library Philosophy and Practice (e-journal)

This study aims to analyse the work done in the field of Night Vision Robots using IR and Object Detection from 2011 to 2021, using the bibliometric methods. This paper presents a Scopus database review on "Night Vision Bot using Dynamic IR and Object Detection". The necessity for doing this bibliometric survey is that to know how the technology in the field of mobile robotics and night vision, as well as to object detection, has evolved over the years. This paper shows the importance of Night Vision Robot from the year 2011 and continued up to 2021 April. The database …

Tractor Hacking, Jin Huang, Kyle B. Kesler

Electrical Engineering

Tractor hacking arose from tractor owners' desire for full control over the tractors they purchase. Tractor manufacturers set strict security on the electrical components of their tractors, making it difficult for tractor owners to diagnose and monitor their tractors on their own. The UltraBlue Tractor Hacking project is a solution to this problem, allowing tractor owners to perform diagnostics and monitor the equipment they purchased without having to go through dealerships. From talking to farmers, we found that they valued a diagnostic tool that allows for clearing and resetting Diagnostic Trouble Codes (DTCs), viewing diagnostic data pertaining to a specific …

Energy Efficient Computing Using Scalable General Purpose Analog Processors, Ethan Paul Palisoc De Guzman

Master's Theses

Due to fundamental physical limitations, conventional digital circuits have not been able to scale at the pace expected from Moore’s law. In addition, computationally intensive applications such as neural networks and computer vision demand large amounts of energy from digital circuits. As a result, energy efficient alternatives are needed in order to provide continued performance scaling. Analog circuits have many well known benefits: the ability to store more information onto a single wire and efficiently perform mathematical operations such as addition, subtraction, and differential equation solving. However, analog computing also comes with drawbacks such as its sensitivity to process variation …

Design And Characterization Of Standard Cell Library Using Finfets, Phanindra Datta Sadhu

Master's Theses

The processors and digital circuits designed today contain billions of transistors on a small piece of silicon. As devices are becoming smaller, slimmer, faster, and more efficient, the transistors also have to keep up with the demands and needs of the daily user. Unfortunately, the CMOS technology has reached its limit and cannot be used to scale down due to the transistor's breakdown caused by short channel effects. An alternative solution to this is the FinFET transistor technology, where the gate of the transistor is a three dimensional fin that surrounds the transistor and prevents the breakdown caused by scaling …

Bibliometric Review Of Predictive Maintenance Using Vibration Analysis, Aashna Midha Ms., Ishita Maheshwari Ms., Kaushik Ojha Mr., Kritika Gupta Ms., Shripad V. Deshpande Mr.

Library Philosophy and Practice (e-journal)

Every day the world is depending more and more on machines in almost every aspect of life. With the increasing use of machines, there also needs to be an evolution in the maintenance of these machines. Predictive maintenance is a process used to monitor the equipment and machinery during its operation to detect any damages and/or deteriorations and enable the required maintenance plan in advance, resulting in reduced operational costs and full utilization of tools and parts. The fundamental goal of this bibliometric review paper is a comprehension of the extent and sources of the literature available for predictive maintenance …

Fault Modeling And Test Vector Generation For Asic Devices Exposed To Space Single Event Environment, Ahmed Mohamed

Theses and Dissertations

This work aims at providing a concise automated flow to predict the effect of Single Event Transients (SETs) on ASIC chips by developing a method to characterize the circuit susceptibility to SET pulses propagation and then generation of the required input vectors that sensitize the victim paths. A new enhanced method for SET electrical propagation modeling is proposed and compared to a previously published analytical model. The method was applied on different standard cells libraries built over XFAB Xh018 technology and verified for accuracy against simulations. The new method showed enhancement in accuracy compared with previous work in literature. Industrial …

A Bibliometric Review Of Characterization Of Outdoor Solar Pv Panel For Shading And Validation By Pv Emulator, Viplove Malik, Poojan Pavagadhi, Aman Kumar Pandey, Saharsh Vyas, Javed Sayyad, Paresh Nasikkar

Library Philosophy and Practice (e-journal)

Many researchers and experts have begun to work in Renewable Energy (RE) Research and Development (R&D) as an interdisciplinary area ineluctable solution to lower the use of conventional power generation or non-renewable resources. Solar photovoltaic energy has gained a lot of recognition as one of the best green alternatives. However, its firm reliance on environmental and climatic conditions makes it difficult for researchers to conduct experiments at the operational temperature (T) and Solar insolation level (G). These solar PV panels with a controllable light source are inefficient, unreliable, and unsuitable for testing PV algorithms such as Maximum Power Point Tracking …

Smart E-Bike Conversion Kit And Helmet, Megan West, Marena Trujillo, Hossein Asghari

Honors Thesis

With many state governments across the United States implementing shutdowns to prevent the spread of COVID-19, many bike retailers have seen dramatic increases in bike sales. Electric bicycles (e-bikes) have become increasingly popular as the public searches for alternatives to public transportation. Unfortunately, e-bike users assume some risk by riding bikes that are faster than conventional bicycles. While kits to convert conventional bicycles to e-bikes exist, no “smart” e-bike/helmet kit specifically designed to keep the user safe is currently available on the market. To mitigate risks, a smart e-bike conversion kit with multiple novel safety features, including auditory and visual …