Open Access. Powered by Scholars. Published by Universities.®
VLSI and Circuits, Embedded and Hardware Systems Commons™
Open Access. Powered by Scholars. Published by Universities.®
- Discipline
- Keyword
Articles 1 - 8 of 8
Full-Text Articles in VLSI and Circuits, Embedded and Hardware Systems
Design Of A Bandgap Voltage Reference, Nicolaus Vail
Design Of A Bandgap Voltage Reference, Nicolaus Vail
Electrical Engineering Undergraduate Honors Theses
This thesis details the design process of a bandgap voltage reference (BGR) integrated circuit in a 180 nm CMOS process. A BGR provides a constant DC voltage across a range of operating temperatures and supply voltages. By its nature, the circuit is intended as a reference, not to provide current, so the output would be connected to a very high impedance, such as the gate of a transistor. At 27°C, this design provides a 955 mV reference voltage given a nominal VDD of 3 V. From 20°C to 175°C, the output voltage has a variance of 7.2 mV (approximately 0.8%) …
Design And Fabrication Of A Microstrip Bandpass Filter In Ltcc, Allison Rucker
Design And Fabrication Of A Microstrip Bandpass Filter In Ltcc, Allison Rucker
Electrical Engineering Undergraduate Honors Theses
The goal of the project was to design and fabricate a bandpass filter with a center frequency of 25GHz with a 2GHz bandwidth. The first step was to do the calculation to design a bandpass filter to meet these specifications along with the properties of the DupontTM GreenTapeTM 9K7. HFSS was then used to verify the results from the initial calculations. There was a significant error between the two results, so more tweaking was done to the calculations to get a better center frequency. After a final design was decided, the fabrication process started. Low-Temperature Co-Fired Ceramics (LLTC) …
Design Of An Embedded Iris Recognition System For Use With A Multi-Factor Authentication System., Christopher David Hess
Design Of An Embedded Iris Recognition System For Use With A Multi-Factor Authentication System., Christopher David Hess
Electrical Engineering Undergraduate Honors Theses
This paper describes in detail the design, manufacturing and testing of an embedded iris scanner for use with a multifactor authentication system. The design process for this project included hardware design from part selection to board design to populating. Additionally, this process included the entirety of the software development, though the iris recognition process was largely based on other works. The functional requirements for the overall multi-factor authentication system were to have three authentication methods with a thirty second window to complete all three. The system acceptance accuracy was required to be greater than 75%. Those requirements therefore dictate that …
Design Of A Folded Cascode Operational Amplifier In A 1.2 Micron Silicon-Carbide Cmos Process, Kyle Addington
Design Of A Folded Cascode Operational Amplifier In A 1.2 Micron Silicon-Carbide Cmos Process, Kyle Addington
Electrical Engineering Undergraduate Honors Theses
This thesis covers the design of a Folded Cascode CMOS Operational Amplifier (Op-Amp) in Raytheon’s 1.2-micron Silicon Carbide (SiC) process. The use of silicon-carbide as a material for integrated circuits (ICs) is gaining popularity due to its ability to function at high temperatures outside the range of typical silicon ICs. The goal of this design was to create an operational amplifier suitable for use in a high temperature analog-to-digital converter application. The amplifier has been designed to have a DC gain of 50dB, a phase margin of 50 degrees, and a bandwidth of 2 MHz. The circuit’s application includes input …
Implementation Of Natural Switching Surface Control For A Flyback Converter, Ethan Storm Williams
Implementation Of Natural Switching Surface Control For A Flyback Converter, Ethan Storm Williams
Electrical Engineering Undergraduate Honors Theses
The flyback converter is an extremely common topology used for DC/DC power conversion. Widely used methods to control the flyback converter include voltage mode and current mode controllers. More recently, sliding mode control has been developed for the flyback converter. While these control methods may be considered adequate, the Natural Switching Surface (NSS) sliding mode control method detailed in this thesis presents a more robust controller. NSS control eliminates the effects presented from variations in components and design as well as minimizes the effects from external disturbances. This thesis steps through the complete design and implementation process of a NSS …
Developing A Tool For Generation Of Operational Amplifier Models From Datasheet Parameters, Benjamin Riley Sissons
Developing A Tool For Generation Of Operational Amplifier Models From Datasheet Parameters, Benjamin Riley Sissons
Electrical Engineering Undergraduate Honors Theses
Due to their flexibility and usefulness operational amplifiers are a very common circuit component that has been in use for over fifty years. Because of their widespread use in circuits there has always been a need for simulation models of the op amp. The purpose of this thesis is to demonstrate the design a tool for use with the modeling software ModLyng that takes several parameters from the datasheet of an op amp and generates a model that can be exported to several popular hardware description languages including Verilog-A and Verilog-AMS. The tool was designed as a plugin for ModLyng …
Automated Behavioral Modeling Of Switching Voltage Regulators, Michael Leonard
Automated Behavioral Modeling Of Switching Voltage Regulators, Michael Leonard
Electrical Engineering Undergraduate Honors Theses
This work describes the development of a software tool that implements a novel method for automatically generating simulation ready behavioral models for switching circuits with an emphasis on power regulators. The work begins by examining the theory of operation of both linear and switching regulators. Then, the capability of two behavioral modeling languages (Verilog-A and PSPICE ABM) are examined in detail. Next, the languages previously discussed are used to develop and test a model of a commercial regulator (Texas Instruments TPS40305). Finally, the prospect of automating the process is discussed
A Study Of Switched-Capacitor Filters, Kacie Thomas
A Study Of Switched-Capacitor Filters, Kacie Thomas
Electrical Engineering Undergraduate Honors Theses
This paper presents the basic principles of the switched-capacitor circuit. In order to become more acquainted with the workings and design of filters and switched-capacitor filters specifically, an example filter was designed based on a set of parameters. It was constructed starting in the passive stage, then the active stage and finally the switched-capacitor filter was generated. All of these circuits were also simulated using SwitcherCAD and Saber. Then, a switched-capacitor filter designed by Auburn University was redesigned using the same process as the example circuit. It was also simulated in all three stages. The results from this design are …