VLSI and Circuits, Embedded and Hardware Systems Commons^™

Vi Energy-Efficient Memristor-Based Neuromorphic Computing Circuits And Systems For Radiation Detection Applications, Jorge Iván Canales Verdial

Electrical and Computer Engineering ETDs

Radionuclide spectroscopic sensor data is analyzed with minimal power consumption through the use of neuromorphic computing architectures. Memristor crossbars are harnessed as the computational substrate in this non-conventional computing platform and integrated with CMOS-based neurons to mimic the computational dynamics observed in the mammalian brain’s visual cortex. Functional prototypes using spiking sparse locally competitive approximations are presented. The architectures are evaluated for classification accuracy and energy efficiency. The proposed systems achieve a 90% true positive accuracy with a high-resolution detector and 86% with a low-resolution detector.

Iii-Nitride Triangular Microcantilevers For Multimodal Sensing Applications, Balaadithya Uppalapati

All Dissertations

Micro-electromechanical systems (MEMS)-based sensors have gained significant attention due to their ability to sense, measure, and process various physical, chemical, and biological parameters. The small size of MEMS sensors provides numerous advantages, including low power consumption, high sensitivity, and rapid response time, making them suitable for various applications in healthcare, automotive, aerospace, and consumer electronics.

In the past few years, AlGaN/GaN MEMS devices have been found to offer several advantages over silicon-based MEMS devices. One of the main advantages of AlGaN/GaN MEMS is their high sensitivity to surface stresses and forces due to their high piezoelectric coefficients. This sensitivity allows …

The Study Of Corrosion On Additive-Manufactured Metals., Braydan Daniels

Electronic Theses and Dissertations

The purpose of this study was to investigate and compare the corrosion mechanisms between wrought and additive-manufactured (3D-printed) copper and stainless steel. The experimental procedure consisted of measuring the open circuit potential, electrochemical impedance spectroscopy, linear sweep voltammetry, Tafel analysis, surface topology, and scanning electron microscopy for each metal within salt water, tap water, sulfuric acid, and synthetic body fluid (excluding copper in synthetic body fluid).

Overall, printed stainless steel was more corrosion-resistant than wrought stainless steel in tap water and synthetic body fluid based on OCP, LSV, and surface topology results. Additionally, printed copper was more corrosion-resistant than wrought …

Design And Implementation Of High-Efficiency, Lightweight, System-Friendly Solid-State Circuit Breaker, Dehao Qin

All Dissertations

Direct current (DC) distribution system has shown potential over the alternative current (AC) distribution system in some application scenarios, e.g., electrified transportation, renewable energy, data center, etc. Because of the fast response speed, DC solid-state circuit breaker (SSCB) becomes a promising technology for the future power electronics intensive DC energy system with fault-tolerant capability. First, a thorough literature survey is performed to review the DC-SSCB technology. The key components for DC-SSCB, including power semiconductors, topologies, energy absorption units, and fault detection circuits, are studied. It is observed that the prior studies mainly focus on the basic interruption capability of the …

Stream Processor Development Using Multi-Threshold Null Convention Logic Asynchronous Design Methodology, Wassim Khalil

Graduate Theses and Dissertations

Decreasing transistor feature size has led to an increase in the number of transistors in integrated circuits (IC), allowing for the implementation of more complex logic. However, such logic also requires more complex clock tree synthesis (CTS) to avoid timing violations as the clock must reach many more gates over larger areas. Thus, timing analysis requires significantly more computing power and designer involvement than in the past. For these reasons, IC designers have been pushed to nix conventional synchronous (SYNC) architecture and explore novel methodologies such as asynchronous, self-timed architecture. This dissertation evaluates the nominal active energy, voltage-scaled active energy, …

Evaluation Of The Dynamic Vision Sensor’S Photoreceptor Circuit For Infrared Event-Based Sensing, Zinah M. Alsaad

Electrical and Computer Engineering ETDs

For space surveillance applications, neuromorphic imaging is being studied as it may perform sensing and tracking tasks with less power and downstream datalink demand. The read-out of the event-based camera is made to only be sensitive to changes in the signals it receives from the photodetector, which results in a datastream of events indicating where and when changes in illumination occur. This is in contrast to the conventional framing camera, which produces images by essentially counting the electrons produced by light incident on each pixel’s photodetector. These cameras are commercially available with siliconbased detectors for applications involving visible wavelengths. However, …

Automated Sensing Methods In Soft Stretchable Sensors For Soft Robotic Gripper, Prosenjit Kumar Ghosh

Electrical Engineering Theses

A soft robot is made from deformable and flexible materials such as silicone, rubber, polymers, etc. Soft robotics is a rapidly evolving field where the human-robot-interaction and bio-inspired design align. The physical characteristics such as highly deformable material and dexterity make soft robots widely applicable. A soft robotic gripper is a robotic hand that acts like a human hand and grasps any object. The most common applications of soft robotics grippers are gripping and locomotion in sensitive applications where high dynamic and sensitivity are essential. Nowadays, soft robotics grippers are used without any sensing method and feedback as it is …

Phone Microwave, Khanh Kim Hoang, Emily Zhou

Computer Engineering

This project involves the installation of remote-control capabilities in an antique 1980s microwave, effectively turning the microwave into a “smart” device. While preserving the original functionality of the microwave, a combination of software and hardware components allows for remote microwave operations. The microwave can be remotely operated by calling the built-in number, and more advanced settings and options can be utilized by texting. The microwave is also secured against unauthorized use with the addition of a PIN code that is required to operate the device.

Safe Kids Car, Nathan Keenan, Jackson Piper, Kyle Law, Anthony Meniru

Williams Honors College, Honors Research Projects

The main goal of this project is to retrofit toy vehicles, such as Powerwheels cars, with safety systems that can protect the driver and those around the driver. Such systems will include lights, including headlights and taillights, and an automatic braking system, which will activate in the face of an inevitable collision. The system will also work with the driver to prevent collisions, providing warnings of impending danger.

Keywords: toy vehicles, collision detection, collision avoidance, automatic braking system, DC motors, automatic headlights.

Wireless Kick Pedal, Jacob Wise, Ryan Kinyo, Bradley Toth, Ian Zanath

Williams Honors College, Honors Research Projects

The goal of the project is to build a wireless kick pedal that allows accessibility to drummers that have leg or foot disabilities and add versatility to multi-instrumentalists looking to add percussion while playing another instrument. The proposed pedal is designed in two main parts, a wearable band that tracks the player’s movement, and a hammer mechanism that receives actuation commands from the wearable band to move the hammer and deliver a drumbeat. The band is designed to be worn on several parts of the body, including the ankle, knee, thigh, or even the arm depending on the user’s situation. …

Wireless Environmental Weather Monitor, Joel Christie-Millett, Nathan Schroeder, Sylvester Wilson, Matthew Szijarto

Williams Honors College, Honors Research Projects

The goal of this senior design/honors project is to create a device that monitors environmental conditions in order to detect a wildfire. This device should notify a user of the status of the environment. The device should also last for 6 months without any human interaction. My role on the team is to design the power supply system that maximizes efficiency and uses renewable energy.

Performance Evaluation Of Face Mask Detection For Real-Time Implementation On An Rpi, Ivan George L. Tarun, Vidal Wyatt M. Lopez, Pamela Anne C. Serrano, Patricia Angela R. Abu, Rosula Reyes, Ma. Regina Justina Estuar

Department of Information Systems & Computer Science Faculty Publications

Mask-wearing remains to be one of the primary protective measures against COVID-19. To address the difficulty of manual compliance monitoring, face mask detection models considerate of both frontal and angled faces were developed. This study aimed to test the performance of the said models in classifying multi-face images and upon running on a Raspberry Pi device. The accuracies and inference speeds were measured and compared when inferencing images with one, two, and three faces and on the desktop and the Raspberry Pi. With an increasing number of faces in an image, the models’ accuracies were observed to decline, while their …

A Phase Change Memory And Dram Based Framework For Energy-Efficient And High-Speed In-Memory Stochastic Computing, Supreeth Mysore

Theses and Dissertations--Electrical and Computer Engineering

Convolutional Neural Networks (CNNs) have proven to be highly effective in various fields related to Artificial Intelligence (AI) and Machine Learning (ML). However, the significant computational and memory requirements of CNNs make their processing highly compute and memory-intensive. In particular, the multiply-accumulate (MAC) operation, which is a fundamental building block of CNNs, requires enormous arithmetic operations. As the input dataset size increases, the traditional processor-centric von-Neumann computing architecture becomes ill-suited for CNN-based applications. This results in exponentially higher latency and energy costs, making the processing of CNNs highly challenging.

To overcome these challenges, researchers have explored the Processing-In Memory (PIM) …

Towards Multipronged On-Chip Memory And Data Protection From Verification To Design And Test, Senwen Kan, Jennifer Dworak

Computer Science and Engineering Theses and Dissertations

Modern System on Chips (SoCs) generally include embedded memories, and these memories may be vulnerable to malicious attacks such as hardware trojan horses (HTHs), test access port exploitation, and malicious software. This dissertation contributes verification as well as design obfuscation solutions aimed at design level detection of memory HTH circuits as well as obfuscation to prevent HTH triggering for embedded memory during functional operation. For malicious attack vectors stemming from test/debug interfaces, this dissertation presents novel solutions that enhance design verification and securitization of an IJTAG based test access interface. Such solutions can enhance SoC protection by preventing memory test …

Low Power Multi-Channel Interface For Charge Based Tactile Sensors, Samuel Hansen

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Analog front end electronics are designed in 65 nm CMOS technology to process charge pulses arriving from a tactile sensor array. This is accomplished through the use of charge sensitive amplifiers and discrete time filters with tunable clock signals located in each of the analog front ends. Sensors were emulated using Gaussian pulses during simulation. The digital side of the system uses SAR (successive approximation register) ADCs for sampling of the processed sensor signals.

Adviser: Sina Balkır

High-Performance Vlsi Architectures For Lattice-Based Cryptography, Weihang Tan

All Dissertations

Lattice-based cryptography is a cryptographic primitive built upon the hard problems on point lattices. Cryptosystems relying on lattice-based cryptography have attracted huge attention in the last decade since they have post-quantum-resistant security and the remarkable construction of the algorithm. In particular, homomorphic encryption (HE) and post-quantum cryptography (PQC) are the two main applications of lattice-based cryptography. Meanwhile, the efficient hardware implementations for these advanced cryptography schemes are demanding to achieve a high-performance implementation.

This dissertation aims to investigate the novel and high-performance very large-scale integration (VLSI) architectures for lattice-based cryptography, including the HE and PQC schemes. This dissertation first presents …

Design And Analysis Of A Discrete, Pcb-Level Low-Power, Microwave Cross-Coupled Differential Lc Voltage-Controlled Oscillator, Pavin Singh Virdee

Master's Theses

Radio Frequency (RF) and Microwave devices are typically implemented in Integrated Circuit (IC) form to minimize parasitics, increase precision and tolerances, and minimize size. Although IC fabrication for students and independent engineers is cost-prohibitive, an abundance of low-cost, easily accessible printed circuit board (PCB) and electronic component manufacturers allows affordable PCB fabrication.

While nearly all microwave voltage-controlled oscillator (VCO) designs are IC-based, this study presents a discrete PCB-level cross-coupled, differential LC VCO to demonstrate this more affordable and accessible approach. This thesis presents a 65 mW, discrete component VCO PCB with industry-comparable RF performance. A phase noise of -103.7 dBc/Hz …

Development Of The Subwave Rov And Neural-Inertial Positioning System, Jason Farmer

Theses and Dissertations

This report documents the development of the Subwave, a remotely-operated underwater vehicle (ROV), and an artificial neural network based inertial positioning system. The Subwave uses the open-source ArduSub software framework, commercial-off-the-shelf hardware components, and several custom systems. It is designed as a platform for researching autonomous underwater vehicles (AUVs). The first step for an AUV is navigating waypoints, which requires the AUV to know its global position. Since global navigation satellite systems (GNSSs) are denied underwater, the available underwater positioning systems were surveyed and determined that all the available systems were too large and expensive for the Subwave. It was …

Embedding A Grid Of Load Cells Into A Dining Table For Automatic Monitoring And Detection Of Eating Events, Mohammad Mayyan

All Dissertations

This dissertation describes a “smart dining table” that can detect and measure consumption events. This work is motivated by the growing problem of obesity, which is a global problem and an epidemic in the United States and Europe. Chapter 1 gives a background on the economic burden of obesity and its comorbidities. For the assessment of obesity, we briefly describe the classic dietary assessment tools and discuss their drawback and the necessity of using more objective, accurate, low-cost, and in-situ automatic dietary assessment tools. We explain in short various technologies used for automatic dietary assessment such as acoustic-, motion-, or …

Evaluation Of Single Phase Smart Pv Inverter Functions In Unbalanced Residential Distribution Systems, Darren Symonette

Graduate Theses and Dissertations

In the United States, smart PV inverters integrated with residential distribution systems are becoming a more common occurrence. With integration of smart PV inverters, power utilities are experiencing an increase of number of operations with regards to switched capacitor banks, voltage regulators and on load tap changers. These increases can lead to excess wear and tear on the devices causing power utilities to perform unwanted replacement and maintenance. However, smart PV inverters when controlled under specific functions can enable these inverters to provide reactive power and voltage control which in turn lowers the number of operations for switched capacitor banks, …

Algorithm Optimization And Hardware Acceleration For Machine Learning Applications On Low-Energy Systems, Jianchi Sun

All Dissertations

Machine learning (ML) has been extensively employed for strategy optimization, decision making, data classification, etc. While ML shows great triumph in its application field, the increasing complexity of the learning models introduces neoteric challenges to the ML system designs. On the one hand, the applications of ML on resource-restricted terminals, like mobile computing and IoT devices, are prevented by the high computational complexity and memory requirement. On the other hand, the massive parameter quantity for the modern ML models appends extra demands on the system's I/O speed and memory size. This dissertation investigates feasible solutions for those challenges with software-hardware …

Design Tunneling Transistor And Schottky Junction Solar Cell Using Van Der Waals Semiconductor Heterostructure, Md Azmot Ullah Khan

LSU Doctoral Dissertations

Transition metal di-chalcogenide (TMDC) materials, being semiconductor in nature, offer Two-dimensional (2D) materials such as graphene and molybdenum disulfide (MoS₂) possess unique and unusual properties that are particularly applicable to nanoelectronics and photovoltaic devices. In this dissertation, four different projects have been done that encompass the implementation of these materials to improve the performance of future transistors and Schottky junction solar cells. In chapter 2, an analytical current transport model of a dual gate tunnel field-effect transistor (TFET) is developed by utilizing the principle of band-to-band tunneling (BTBT) and MoS₂ as the channel material. Later, using this …

Characterization Of Electrophoretic Deposited Zinc Oxide Nanopartices For The Fabrication Of Next-Generation Nanoscale Electronic Applications, Fawwaz Abduh A. Hazzazi

LSU Doctoral Dissertations

Several reports state that it is crucial to analyze nanoscale semiconductor materials and devices with potential benefits to meet the need for next-generation nanoelectronics, bio, and nanosensors. The progress in the electronics field is as significant now, with modern technology constantly evolving and a greater focus on more efficient robust optoelectronic applications. This dissertation focuses on the study and examination of the practicality of Electrophoretic Deposition (EPD) of zinc oxide (ZnO) nanoparticles (NPs) for use in semiconductor applications.

The feasibility of several synthesized electrolytes, with and without surfactants and APTES surface functionalization, is discussed. The primary objective of this study …

Machine Learning Applications To Static Timing Analysis, Waseem Mohamed Raslan

Theses and Dissertations

Modeling complex cell behavior is critical for accurate static timing analysis. Effective current source model, ECSM, and composite current source, CCS, waveform data compression became a necessity to reduce the size of technology files and increase the accuracy of the cell characterization data. We used deep learning nonlinear Autoencoders to compress voltage and current waveforms and compared them with singular value decomposition, SVD, approach. Autoencoders gave ~1.67x compression ratio for voltage waveforms better than SVD approach and gave 45x to 55x better compression ratio compared to other lossless techniques like bz2 and gzip. Autoencoders achieved ~1.7x compression ratio for complex …

Modified Q-Learning Method For Automatic Voltage Regulation In Wide-Area Multigeneration Systems, Brook Abegaz, Sina Zarrabian

Engineering Science Faculty Publications

The state-estimation and optimal control of multigeneration systems are challenging for wide-area systems having numerous distributed automatic voltage regulators (AVR). This paper proposes a modified Q-learning method and algorithm that aim to improve the convergence of the approach and enhance the dynamic response and stability of the terminal voltage of multiple generators in the experimental Western System Coordinating Council (WSCC) and large-scale IEEE 39-bus test systems. The large-scale experimental testbed consists of a six-area, 39-bus system having ten generators that are connected to ten AVRs. The implementation shows promising results in providing stable terminal voltage profiles and other system parameters …

Smartphone Control Of Rc Cars, Weston R. Fitzgerald

Electrical Engineering

The smartphone-controlled RC (remote-controlled) car is an inexpensive remote-controlled car designed to be fast and portable. Instead of manufacturing, packaging, and shipping a separate controller, the remote control is implemented in a phone application, which saves time and money in both the design process and the manufacturing process. Utilizing the user’s smartphone is more cost-effective since mobile devices are a common recurrence, and packaging fewer devices results in overall better portability of the product.

This smartphone-controlled car is speedy and intuitive to learn for typical smartphone users. The user can change the car’s speed and direction wirelessly using their phone; …

Mars Prototype Rover Environmental Measurement System, James A. Renick

Computer Engineering

In my senior project, the problem I am trying to solve is how to efficiently design, create, and install an original library onto a Mars prototype rover operating system and to further use that library to integrate a new weather measurement sensor device into the rover system with the necessary software and hardware implementations. This is an important and highly valued problem as many aerospace and other engineering companies utilize rovers and other autonomous systems for important research, explorations, and reconnaissance missions and goals. In solving this problem, I utilized many resources that were available to me such as advisors, …

Signal Adc Converter Simulation On Cadence Virtuoso For Audio Applications, Maxwell Kazuki Fukada

Electrical Engineering

Audio signals are representations of sounds with a mixture of multiple analog signals between the frequency of 20Hz to 20,000Hz. To record snippets of audio data onto a mobile phone or computer, the signal needs to be converted to a digital format. For this purpose, many devices utilize a converter, specifically a sigma-delta modulator with a digital filter. By using a converter, electronics can receive binary data about the audio signal accurately and quickly without losing important signal information. This project aims to simulate a fully functional audio converter with a sigma-delta modulator and decimation filter. The system will receive …

Integrated Circuits Parasitic Capacitance Extraction Using Machine Learning And Its Application To Layout Optimization, Mohamed Saleh Abouelyazid Saleh

Theses and Dissertations

The impact of parasitic elements on the overall circuit performance keeps increasing from one technology generation to the next. In advanced process nodes, the parasitic effects dominate the overall circuit performance. As a result, the accuracy requirements of parasitic extraction processes significantly increased, especially for parasitic capacitance extraction. Existing parasitic capacitance extraction tools face many challenges to cope with such new accuracy requirements that are set by semiconductor foundries (< 5% error). Although field-solver methods can meet such requirements, they are very slow and have a limited capacity. The other alternative is the rule-based parasitic capacitance extraction methods, which are faster and have a high capacity; however, they cannot consistently provide good accuracy as they use a pre-characterized library of capacitance formulas that cover a limited number of layout patterns. On the other hand, the new parasitic extraction accuracy requirements also added more challenges on existing parasitic-aware routing optimization methods, where simplified parasitic models are used to optimize layouts.

This dissertation provides new solutions for interconnect parasitic capacitance extraction and parasitic-aware routing optimization methodologies in order to cope with the new accuracy requirements of advanced process nodes as follows. …

Enhanced Design For Testability Circuitry For Test, Hui Jiang

Electrical Engineering Theses and Dissertations

More stringent defect detection requirements have led to the creation of new fault models, such as the cell-aware fault model, that attempts to model defects that might be missed by traditional test sets. Unfortunately, the resulting test sets can be long, and thus we have previously explored a DFT-based (Design for Testability-based) approach to reduce test time by harnessing scan shift cycles for cell-aware defect detection. This approach uses a MISR (Multiple Input Signature Register) structure to capture data on the functional inputs to selected scan flip-flops during the shifting procedure. The final signature in the MISR can then be …