VLSI and Circuits, Embedded and Hardware Systems Commons^™

Towards Multipronged On-Chip Memory And Data Protection From Verification To Design And Test, Senwen Kan, Jennifer Dworak

Computer Science and Engineering Theses and Dissertations

Modern System on Chips (SoCs) generally include embedded memories, and these memories may be vulnerable to malicious attacks such as hardware trojan horses (HTHs), test access port exploitation, and malicious software. This dissertation contributes verification as well as design obfuscation solutions aimed at design level detection of memory HTH circuits as well as obfuscation to prevent HTH triggering for embedded memory during functional operation. For malicious attack vectors stemming from test/debug interfaces, this dissertation presents novel solutions that enhance design verification and securitization of an IJTAG based test access interface. Such solutions can enhance SoC protection by preventing memory test …

Low Power Multi-Channel Interface For Charge Based Tactile Sensors, Samuel Hansen

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Analog front end electronics are designed in 65 nm CMOS technology to process charge pulses arriving from a tactile sensor array. This is accomplished through the use of charge sensitive amplifiers and discrete time filters with tunable clock signals located in each of the analog front ends. Sensors were emulated using Gaussian pulses during simulation. The digital side of the system uses SAR (successive approximation register) ADCs for sampling of the processed sensor signals.

Adviser: Sina Balkır

High-Performance Vlsi Architectures For Lattice-Based Cryptography, Weihang Tan

All Dissertations

Lattice-based cryptography is a cryptographic primitive built upon the hard problems on point lattices. Cryptosystems relying on lattice-based cryptography have attracted huge attention in the last decade since they have post-quantum-resistant security and the remarkable construction of the algorithm. In particular, homomorphic encryption (HE) and post-quantum cryptography (PQC) are the two main applications of lattice-based cryptography. Meanwhile, the efficient hardware implementations for these advanced cryptography schemes are demanding to achieve a high-performance implementation.

This dissertation aims to investigate the novel and high-performance very large-scale integration (VLSI) architectures for lattice-based cryptography, including the HE and PQC schemes. This dissertation first presents …

Design And Analysis Of A Discrete, Pcb-Level Low-Power, Microwave Cross-Coupled Differential Lc Voltage-Controlled Oscillator, Pavin Singh Virdee

Master's Theses

Radio Frequency (RF) and Microwave devices are typically implemented in Integrated Circuit (IC) form to minimize parasitics, increase precision and tolerances, and minimize size. Although IC fabrication for students and independent engineers is cost-prohibitive, an abundance of low-cost, easily accessible printed circuit board (PCB) and electronic component manufacturers allows affordable PCB fabrication.

While nearly all microwave voltage-controlled oscillator (VCO) designs are IC-based, this study presents a discrete PCB-level cross-coupled, differential LC VCO to demonstrate this more affordable and accessible approach. This thesis presents a 65 mW, discrete component VCO PCB with industry-comparable RF performance. A phase noise of -103.7 dBc/Hz …

Development Of The Subwave Rov And Neural-Inertial Positioning System, Jason Farmer

Theses and Dissertations

This report documents the development of the Subwave, a remotely-operated underwater vehicle (ROV), and an artificial neural network based inertial positioning system. The Subwave uses the open-source ArduSub software framework, commercial-off-the-shelf hardware components, and several custom systems. It is designed as a platform for researching autonomous underwater vehicles (AUVs). The first step for an AUV is navigating waypoints, which requires the AUV to know its global position. Since global navigation satellite systems (GNSSs) are denied underwater, the available underwater positioning systems were surveyed and determined that all the available systems were too large and expensive for the Subwave. It was …

Embedding A Grid Of Load Cells Into A Dining Table For Automatic Monitoring And Detection Of Eating Events, Mohammad Mayyan

All Dissertations

This dissertation describes a “smart dining table” that can detect and measure consumption events. This work is motivated by the growing problem of obesity, which is a global problem and an epidemic in the United States and Europe. Chapter 1 gives a background on the economic burden of obesity and its comorbidities. For the assessment of obesity, we briefly describe the classic dietary assessment tools and discuss their drawback and the necessity of using more objective, accurate, low-cost, and in-situ automatic dietary assessment tools. We explain in short various technologies used for automatic dietary assessment such as acoustic-, motion-, or …

Evaluation Of Single Phase Smart Pv Inverter Functions In Unbalanced Residential Distribution Systems, Darren Symonette

Graduate Theses and Dissertations

In the United States, smart PV inverters integrated with residential distribution systems are becoming a more common occurrence. With integration of smart PV inverters, power utilities are experiencing an increase of number of operations with regards to switched capacitor banks, voltage regulators and on load tap changers. These increases can lead to excess wear and tear on the devices causing power utilities to perform unwanted replacement and maintenance. However, smart PV inverters when controlled under specific functions can enable these inverters to provide reactive power and voltage control which in turn lowers the number of operations for switched capacitor banks, …

Algorithm Optimization And Hardware Acceleration For Machine Learning Applications On Low-Energy Systems, Jianchi Sun

All Dissertations

Machine learning (ML) has been extensively employed for strategy optimization, decision making, data classification, etc. While ML shows great triumph in its application field, the increasing complexity of the learning models introduces neoteric challenges to the ML system designs. On the one hand, the applications of ML on resource-restricted terminals, like mobile computing and IoT devices, are prevented by the high computational complexity and memory requirement. On the other hand, the massive parameter quantity for the modern ML models appends extra demands on the system's I/O speed and memory size. This dissertation investigates feasible solutions for those challenges with software-hardware …

Design Tunneling Transistor And Schottky Junction Solar Cell Using Van Der Waals Semiconductor Heterostructure, Md Azmot Ullah Khan

LSU Doctoral Dissertations

Transition metal di-chalcogenide (TMDC) materials, being semiconductor in nature, offer Two-dimensional (2D) materials such as graphene and molybdenum disulfide (MoS₂) possess unique and unusual properties that are particularly applicable to nanoelectronics and photovoltaic devices. In this dissertation, four different projects have been done that encompass the implementation of these materials to improve the performance of future transistors and Schottky junction solar cells. In chapter 2, an analytical current transport model of a dual gate tunnel field-effect transistor (TFET) is developed by utilizing the principle of band-to-band tunneling (BTBT) and MoS₂ as the channel material. Later, using this …

Characterization Of Electrophoretic Deposited Zinc Oxide Nanopartices For The Fabrication Of Next-Generation Nanoscale Electronic Applications, Fawwaz Abduh A. Hazzazi

LSU Doctoral Dissertations

Several reports state that it is crucial to analyze nanoscale semiconductor materials and devices with potential benefits to meet the need for next-generation nanoelectronics, bio, and nanosensors. The progress in the electronics field is as significant now, with modern technology constantly evolving and a greater focus on more efficient robust optoelectronic applications. This dissertation focuses on the study and examination of the practicality of Electrophoretic Deposition (EPD) of zinc oxide (ZnO) nanoparticles (NPs) for use in semiconductor applications.

The feasibility of several synthesized electrolytes, with and without surfactants and APTES surface functionalization, is discussed. The primary objective of this study …

Machine Learning Applications To Static Timing Analysis, Waseem Mohamed Raslan

Theses and Dissertations

Modeling complex cell behavior is critical for accurate static timing analysis. Effective current source model, ECSM, and composite current source, CCS, waveform data compression became a necessity to reduce the size of technology files and increase the accuracy of the cell characterization data. We used deep learning nonlinear Autoencoders to compress voltage and current waveforms and compared them with singular value decomposition, SVD, approach. Autoencoders gave ~1.67x compression ratio for voltage waveforms better than SVD approach and gave 45x to 55x better compression ratio compared to other lossless techniques like bz2 and gzip. Autoencoders achieved ~1.7x compression ratio for complex …

Modified Q-Learning Method For Automatic Voltage Regulation In Wide-Area Multigeneration Systems, Brook Abegaz, Sina Zarrabian

Engineering Science Faculty Publications

The state-estimation and optimal control of multigeneration systems are challenging for wide-area systems having numerous distributed automatic voltage regulators (AVR). This paper proposes a modified Q-learning method and algorithm that aim to improve the convergence of the approach and enhance the dynamic response and stability of the terminal voltage of multiple generators in the experimental Western System Coordinating Council (WSCC) and large-scale IEEE 39-bus test systems. The large-scale experimental testbed consists of a six-area, 39-bus system having ten generators that are connected to ten AVRs. The implementation shows promising results in providing stable terminal voltage profiles and other system parameters …

Smartphone Control Of Rc Cars, Weston R. Fitzgerald

Electrical Engineering

The smartphone-controlled RC (remote-controlled) car is an inexpensive remote-controlled car designed to be fast and portable. Instead of manufacturing, packaging, and shipping a separate controller, the remote control is implemented in a phone application, which saves time and money in both the design process and the manufacturing process. Utilizing the user’s smartphone is more cost-effective since mobile devices are a common recurrence, and packaging fewer devices results in overall better portability of the product.

This smartphone-controlled car is speedy and intuitive to learn for typical smartphone users. The user can change the car’s speed and direction wirelessly using their phone; …

Mars Prototype Rover Environmental Measurement System, James A. Renick

Computer Engineering

In my senior project, the problem I am trying to solve is how to efficiently design, create, and install an original library onto a Mars prototype rover operating system and to further use that library to integrate a new weather measurement sensor device into the rover system with the necessary software and hardware implementations. This is an important and highly valued problem as many aerospace and other engineering companies utilize rovers and other autonomous systems for important research, explorations, and reconnaissance missions and goals. In solving this problem, I utilized many resources that were available to me such as advisors, …

Signal Adc Converter Simulation On Cadence Virtuoso For Audio Applications, Maxwell Kazuki Fukada

Electrical Engineering

Audio signals are representations of sounds with a mixture of multiple analog signals between the frequency of 20Hz to 20,000Hz. To record snippets of audio data onto a mobile phone or computer, the signal needs to be converted to a digital format. For this purpose, many devices utilize a converter, specifically a sigma-delta modulator with a digital filter. By using a converter, electronics can receive binary data about the audio signal accurately and quickly without losing important signal information. This project aims to simulate a fully functional audio converter with a sigma-delta modulator and decimation filter. The system will receive …

Integrated Circuits Parasitic Capacitance Extraction Using Machine Learning And Its Application To Layout Optimization, Mohamed Saleh Abouelyazid Saleh

Theses and Dissertations

The impact of parasitic elements on the overall circuit performance keeps increasing from one technology generation to the next. In advanced process nodes, the parasitic effects dominate the overall circuit performance. As a result, the accuracy requirements of parasitic extraction processes significantly increased, especially for parasitic capacitance extraction. Existing parasitic capacitance extraction tools face many challenges to cope with such new accuracy requirements that are set by semiconductor foundries (< 5% error). Although field-solver methods can meet such requirements, they are very slow and have a limited capacity. The other alternative is the rule-based parasitic capacitance extraction methods, which are faster and have a high capacity; however, they cannot consistently provide good accuracy as they use a pre-characterized library of capacitance formulas that cover a limited number of layout patterns. On the other hand, the new parasitic extraction accuracy requirements also added more challenges on existing parasitic-aware routing optimization methods, where simplified parasitic models are used to optimize layouts.

This dissertation provides new solutions for interconnect parasitic capacitance extraction and parasitic-aware routing optimization methodologies in order to cope with the new accuracy requirements of advanced process nodes as follows. …

Enhanced Design For Testability Circuitry For Test, Hui Jiang

Electrical Engineering Theses and Dissertations

More stringent defect detection requirements have led to the creation of new fault models, such as the cell-aware fault model, that attempts to model defects that might be missed by traditional test sets. Unfortunately, the resulting test sets can be long, and thus we have previously explored a DFT-based (Design for Testability-based) approach to reduce test time by harnessing scan shift cycles for cell-aware defect detection. This approach uses a MISR (Multiple Input Signature Register) structure to capture data on the functional inputs to selected scan flip-flops during the shifting procedure. The final signature in the MISR can then be …

Design Of A Bandgap Voltage Reference, Nicolaus Vail

Electrical Engineering Undergraduate Honors Theses

This thesis details the design process of a bandgap voltage reference (BGR) integrated circuit in a 180 nm CMOS process. A BGR provides a constant DC voltage across a range of operating temperatures and supply voltages. By its nature, the circuit is intended as a reference, not to provide current, so the output would be connected to a very high impedance, such as the gate of a transistor. At 27°C, this design provides a 955 mV reference voltage given a nominal VDD of 3 V. From 20°C to 175°C, the output voltage has a variance of 7.2 mV (approximately 0.8%) …

Photoassisted Nanoscale Memory Resistors, Amir Shariffar

Graduate Theses and Dissertations

Memristors or memory resistors are promising two-terminal devices, which have the potential to revolutionize current electronic memory technologies. Memristors have been extensively investigated and reported to be practical devices, although they still suffer from poor stability, low retention time, and laborious fabrication processes.

The primary aim of this project was to achieve a device structure of quantum dots or thin films to address a fundamental challenge of unstable resistive switching behavior in memristors. Moreover, we aimed to investigate the effects of light illumination in terms of intensity and wavelength on the performance of the fabricated memristor. The parameters such as …

Automatic Testing Of Organic Strain Gauge Tactile Sensors., Brian P. Goulet

Electronic Theses and Dissertations

Human-Robot Interaction is a developing field of science, that is posed to augment everything we do in life. Skin sensors that can detect touch, temperature, distance, and other physical interaction parameters at the human-robot interface are very important to enhancing the collaboration between humans and machines. As such, these sensors must be efficiently tested and characterized to give accurate feedback from the sensor to the robot. The objective of this work is to create a diversified software testing suite that removes as much human intervention as possible. The tests and methodology discussed here provide multiple realistic scenarios that the sensors …

Framework Of Hardware Trojan Detection Leveraging Structural Checking Tool, Rafael Dacanay Del Carmen

Graduate Theses and Dissertations

Since there is a significant demand for obtaining third-party soft Intellectual Property (IP) by first-party integrated circuit (IC) vendors, it is becoming easier for adversaries to insert malicious logic known as hardware Trojans into designs. Due to this, vendors need to find ways to screen the third-party IPs for possible security threats and then mitigate them. The development of the Structural Checking (SC) tool provides a solution to this issue. This tool analyzes the structure of an unknown soft IP design and creates a network of all the signals within the design and how they are connected to each other. …

Incorporating In Situ Measurements Of Energy Into A Designed Method Of Detection Of Radiation Induced Degradation In Embedded Systems, Delwyn Sam

Honors Theses

An embedded system, or a system-on-chip (SOC), is a miniaturized computer that combines hardware and software to accomplish a certain purpose. Embedded systems are used in various applications from household appliances to the automobile industry. Additionally, SOCs are used in space environments where the surroundings consist of radiation and extreme temperatures. In these harsh conditions, embedded systems must operate properly through the effects of radiation such as total ionizing dose (TID). Because embedded systems are filled with various components and modules, and since the internal signals of the system are often inaccessible, methods to locate which specific parts of the …

Junction Temperature Estimation Of Silicon Carbide Power Module Using Internal Gate Resistance As Temperature Sensitive Electrical Parameter, Michael Sykes

Graduate Theses and Dissertations

The junction temperature of a power module is measured non-intrusively and uninterrupted in its application by analyzing the dependency of gate resistance to temperature. The circuit configuration proposed consists of altering the gate loop path and adding a basic peak detection circuit with an added low-pass filter to accurately measure the small differences seen during a temperature change on the internal gate resistance. The testing on this Silicon Carbide power module shows that the internal gate resistance has a positive temperature coefficient. This causes the current and the voltage drop on the gate loop sensing resistance to reduce as the …

Design & Analysis Of Mixed-Mode Integrated Circuit For Pulse-Shape Discrimination, Bryan Orabutt

McKelvey School of Engineering Graduate Student Theses & Dissertations

In nuclear science experiments it is usually necessary to determine the type of radiation, its energy and direction with considerable accuracy. The detection of neutrons and discriminating them from gamma rays is particularly difficult. A popular method of doing so is to measure characteristics intrinsic to the pulse shape of each radiation type in order to perform pulse-shape discrimination (PSD).

Historically, PSD capable systems have been designed with two approaches in mind: specialized analog circuitry, or digital signal processing (DSP). In this work we propose a PSD capable circuit topology using techniques from both the analog and DSP domains. We …

Combat Robot, Wayne Lambert, Elijah Harris, Brian Eiseman, Jordan Meyer

ONU Student Research Colloquium

The senior capstone project that was tasked to the team was the decision of choosing a challenge within a national robotics competition. The group decided to compete at the National Robotics Challenge in Marion, Ohio. The idea was to participate in the combat robot competition at this NRC event. Once this decision had been made the next steps were to get an idea of what the rules and requirements of the competition were and to try and to sketch a very rough drawing of what the ideal robot should look like. From there it was decided to start a timeline …

Single Event Transient Sensitivity Measurement And Worst-Case Test Vector Exploration For Asic Devices Exposed To Space Single Event Environment, Mohamed Wael

Theses and Dissertations

Space radiation and nuclear reactors produce single event effects (SEE) in electronic circuits and impact their performance. The SEE phenomena cause circuits and electronic devices to fail by producing faulty results. Therefore, today’s circuit’s reliability is a significant concern for all circuit designers.

This thesis suggests a new automated flow to measure the single-event-transient (SET) effects in combinational circuits in application-specific integrated circuits (ASIC) while reaching full fault coverage. The developed flow characterizes the whole circuit nodes by identifying the most sensitive paths to the propagated SET pulses from the node under test to an observable primary output, causing single …

Modeling And Control Of Direct-Conversion Hybrid Switched-Capacitor Dc-Dc Converters, Ziyu Xia

Dartmouth College Ph.D Dissertations

Efficient power delivery is increasingly important in modern computing, communications, consumer and other electronic systems, due to the high power demand and thermal concerns accompanied by performance advancements and tight packaging. In pursuit of high efficiency, small physical volume, and flexible regulation, hybrid switched-capacitor topologies have emerged as promising candidates for such applications. By incorporating both capacitors and inductors as energy storage elements, hybrid topologies achieve high power density while still maintaining soft charging and efficient regulation characteristics. However, challenges exist in the hybrid approach. In terms of reliability, each flying capacitor should be maintained at a nominal `balanced' voltage …

The Design Of Cmos Front-End Amplifiers For Electrical Impedance Applications, Yueh-Ching Teng

Dartmouth College Ph.D Dissertations

Electrical Impedance Tomography (EIT) is a medical imaging methodology that does not need any kind of ionizing radiation. It is significantly cheaper and smaller than Computerized Tomography (CT) or Magnetic Resonance Imaging (MRI). These advantages make EIT particularly suitable for emerging applications like the continuous medical imaging and telemonitoring of organ function. Current bench-top EIT systems are bulky and require shielded cables to interface with measurement electrodes. The cable introduces parasitic capacitances which shunt the desired signals and degrade the accuracy of the measurements. A EIT system based on application-specific integrated circuits (ASICs) can reduce the parasitic and stray capacitance …

Autonomous Coffee Brewing System, Lillian Gonzalez, Landon Miller, Tyler Moff, Benjamin Vitu

Williams Honors College, Honors Research Projects

Coffee consumers want an affordable, high-quality cup of coffee that takes minimal time to brew and does not excessively contribute plastic to landfills. A fully autonomous system which utilizes whole coffee beans, water, and filters to brew coffee was designed to meet this need. This system accepts user requests which specify the brew’s portion size, water temperature, and brew strength, as well as the time which the system should begin the brewing process. Occasional maintenance to empty the system’s built-in waste receptacle or resupply the system with water, coffee beans, or filters is the only user intervention required. This report …

Smart Bike Aftermarket System (Sbams), Noah Lamadanie, Jack Bullock, Dawson Beachy, John Albrecht

Williams Honors College, Honors Research Projects

The Smart Bike Aftermarket System will be a set of connected modules, which, when installed on a standard bicycle, will allow it to mimic some of the safety and quality-of-life functionalities of an E-bike. The most notable of these safety features is an ability to detect vehicles approaching from behind and alert the user of potential collisions. The system will also implement lighting (Headlights, taillights, and turn signals), and a coupled application so a user can view more advanced information about their cycling. The primary advantage of this system over a standard E-bike is that it will have a lower …