VLSI and Circuits, Embedded and Hardware Systems Commons^™

Retinomorphic Mid-Wave Infrared In-Sensor Processing Engine: Device-To-Architecture Co-Design, Hemalatha Nagaraju

Theses

Conventional frame-based CMOS image sensors acquire full-frame pixel data at discrete time intervals, resulting in substantial spatial redundancy and loss of temporal information between frames. The repeated conversion and transfer of redundant pixel data increases bandwidth and power consumption in machine vision systems. Retinomorphic sensing architectures address these limitations by enabling programmable, analog-domain processing directly at the sensor interface. A compact behavioral model of the PbSe device is developed in HSPICE based on calibrated TCAD simulation data to capture gate-controlled photocurrent modulation under varying illumination and gate bias conditions. Error analysis is performed to quantify the deviation between TCAD-generated photocurrent …

Development Of Alternative Plasma Etching Techniques For The Selective Removal Of Tan With Respect To Sioch Dielectric Materials To Enable Future Back-End-Of-The-Line Scaling, Ivo Otto Iv

Electronic Theses & Dissertations (2024 - present)

Transistor scaling has continued according to Moore’s Law for over fifty years. As transistor size decreases, adequate power delivery is required to enable transistor scaling without performance loss. Power delivery is provided by a metal interconnect network with insulating dielectric that connects the transistor level to the power source, the signal speed within this metal line network limiting transistor level switching speeds. Reduction of signal delay has moved from primarily dimension-based improvement towards adoption of conductor and dielectric materials with lower resistivity and a reduced dielectric constant value, respectively: transitioning from Al/SiO₂ to Cu/low-κ SiOCH. With this transition comes …

Development Of A Multi-Use Modular Microfluidic Platform Using 3d Printing, Carson Emeigh

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Microfluidic lab-on-a-chip (LoC) technology has driven numerous innovations due to their ability to perform laboratory-scale experiments on a single chip using microchannels. Although LoC technology has been innovative, it still suffers from limitations related to its fabrication and design flexibility. Typical LoC fabrication, with photolithography, is time consuming, expensive, and inflexible. To overcome the limitations of LoC devices, modular microfluidic platforms have been developed where multiple microfluidic modules, each with a specific function or group of functions, can be combined on a single platform. Modular microfluidics have overcome some of the limitations of LoC devices, but currently, their fabrication is …

Iii-Nitride Triangular Microcantilevers For Multimodal Sensing Applications, Balaadithya Uppalapati

All Dissertations

Micro-electromechanical systems (MEMS)-based sensors have gained significant attention due to their ability to sense, measure, and process various physical, chemical, and biological parameters. The small size of MEMS sensors provides numerous advantages, including low power consumption, high sensitivity, and rapid response time, making them suitable for various applications in healthcare, automotive, aerospace, and consumer electronics.

In the past few years, AlGaN/GaN MEMS devices have been found to offer several advantages over silicon-based MEMS devices. One of the main advantages of AlGaN/GaN MEMS is their high sensitivity to surface stresses and forces due to their high piezoelectric coefficients. This sensitivity allows …

The Study Of Corrosion On Additive-Manufactured Metals., Braydan Daniels

Electronic Theses and Dissertations

The purpose of this study was to investigate and compare the corrosion mechanisms between wrought and additive-manufactured (3D-printed) copper and stainless steel. The experimental procedure consisted of measuring the open circuit potential, electrochemical impedance spectroscopy, linear sweep voltammetry, Tafel analysis, surface topology, and scanning electron microscopy for each metal within salt water, tap water, sulfuric acid, and synthetic body fluid (excluding copper in synthetic body fluid).

Overall, printed stainless steel was more corrosion-resistant than wrought stainless steel in tap water and synthetic body fluid based on OCP, LSV, and surface topology results. Additionally, printed copper was more corrosion-resistant than wrought …

Design And Fabrication Of A Microstrip Bandpass Filter In Ltcc, Allison Rucker

Electrical Engineering Undergraduate Honors Theses

The goal of the project was to design and fabricate a bandpass filter with a center frequency of 25GHz with a 2GHz bandwidth. The first step was to do the calculation to design a bandpass filter to meet these specifications along with the properties of the Dupont^TM GreenTape^TM 9K7. HFSS was then used to verify the results from the initial calculations. There was a significant error between the two results, so more tweaking was done to the calculations to get a better center frequency. After a final design was decided, the fabrication process started. Low-Temperature Co-Fired Ceramics (LLTC) …

Switching Trajectory Control For High Voltage Silicon Carbide Power Devices With Novel Active Gate Drivers, Shuang Zhao

Graduate Theses and Dissertations

The penetration of silicon carbide (SiC) semiconductor devices is increasing in the power industry due to their lower parasitics, higher blocking voltage, and higher thermal conductivity over their silicon (Si) counterparts. Applications of high voltage SiC power devices, generally 10 kV or higher, can significantly reduce the amount of the cascaded levels of converters in the distributed system, simplify the system by reducing the number of the semiconductor devices, and increase the system reliability.

However, the gate drivers for high voltage SiC devices are not available on the market. Also, the characteristics of the third generation 10 kV SiC MOSFETs …

A Silicon Carbide Based Solid-State Fault Current Limiter For Modern Power Distribution Systems, Erik Darnell Johnson

Graduate Theses and Dissertations

The fault current limiter represents a developing technology which will greatly improve the reliability and stability of the power grid. By reducing the magnitude of fault currents in distribution systems, fault current limiters can alleviate much of the damage imposed by these events. Solid-state fault current limiters in particular offer many improved capabilities in comparison to the power system protection equipment which is currently being used for fault current mitigation. The use of silicon carbide power semiconductor devices in solid-state fault current limiters produces a system that would help to advance the infrastructure of the electric grid.

A solid-state fault …

Polyenvi, Stephen Beard, Josh Engel, Paul Fake, Diego Flores, Alvaro Nunez, Miguel Wong

Electrical Engineering

Poor indoor air quality is a problem that is recognized by the Environmental Protection Agency (EPA) to cause health issues. In order to raise awareness of this problem, this document outlines the construction of a device that economically measures air quality through five metrics: dust, smoke, ozone, humidity, and temperature. The device integrates with a router to provide users access to information about their indoor air quality anywhere over the internet as well as local access to the data via an LCD mounted on the router. By increasing indoor air quality awareness, this device will aid users in making adjustments …