Polymer and Organic Materials Commons^™

Solution Casting And Mechanical Testing Of Arabinan-Cellulose Nanocomposites, Kevin Su, Alina Lusebrink

Materials Engineering

The purpose of this work was to investigate methods to produce consistent, reliable, and testable thin films of arabinan-cellulose nanocomposites. Mechanical properties and composition of the Opuntia ficus-indica cactus spines served as motivation for this research. The high specific strength and stiffness, biodegradability, and sustainability of these spines inspired the creation of composites fabricated from the same materials found in cactus spines: arabinan and nanocrystalline cellulose (NCC). Arabinan serves as the matrix material and NCC as the reinforcement. To explore the feasibility of using a non-toxic solvent, different solution casting techniques with water as a solvent were investigated. Ultrasonication was …

Effect Of Metal Organic Framework Concentration On The Crystallization Of Pla-Al-Mof Composites, Eric Futak, Jeffrey Norton, Jessie O'Connell, Nestor Vazquez

Materials Engineering

Poly(lactic acid) (PLA), a well-known biopolymer, is lacking in barrier properties and toughness. The research goal of this project is to look at the crystallinity of PLA when combined with metal organic framework (MOF). It is speculated that MOF has an effect on PLA chain mobility, and therefore crystallinity. In this study, aluminum MOF was added to PLA in varying concentrations (0, 0.5, 1, 2, 5, 10, and 20 wt%) to observe the crystallinity of the composite. The resulting PLA-Al-MOF composite films were characterized using differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and scanning electron …

Low-Cost Prosthetic Transfemoral Socket, Emelie Deans, Joshua Ledgerwood, Leah Moore, Shaina Jung, Kristen Temnyk

Mechanical Engineering

The goal of this senior project was to design and fabricate a low-cost adjustable prosthetic socket for above the knee amputees. This low-cost consideration was incorporated with the original intent to be used in Fiji, however, this changed to the Dominican Republic. It became clear that the need for an adjustable socket was more as a transitional socket. This transitional socket would be used for the first 6 -12 months upon amputation because this when the most amount of volume fluctuation occurs. The project sponsor, LIM Innovations, has already designed the Infinite Socket which contains four main functioning parts: baseplate, …

Manufacturing And Characterization Of Poly (Lactic Acid)/Carbon Black Conductive Composites For Fdm Feedstock: An Exploratory Study, Dylan Fitz-Gerald, Justin Boothe

Materials Engineering

This exploratory study developed methods of manufacturing and characterizing the electrical properties of small batches of conductive composite feedstock for the Fused Deposition Modeling (FDM) manufacturing process, commonly known as 3D printing. We utilized a solution casting process of Poly(lactic acid) (PLA) (Grade 4043D, NatureWorks, LLC.) and Carbon Black (CB) (Vulcan® XC72, Cabot Corp.) in chloroform. The resulting composite precursor was cryogenically treated with liquid nitrogen and milled in a coffee grinder in order to achieve particles that could be fed into the extruder. Composite precursors were dried in a vacuum oven at an elevated temperature of 38°C. Filaments were …

Design And Testing Of A Top Mask Projection Ceramic Stereolithography System For Ceramic Part Manufacturing, Dylan Robert De Caussin

Master's Theses

Ceramic manufacturing is an expensive process with long lead times between

the initial design and final manufactured part. This limits the use of ceramic as a viable material unless there is a large project budget or high production volume associated with the part. Ceramic stereolithography is an alternative to producing low cost parts through the mixing of a photo curable resin and ceramic particles. This is an additive manufacturing process in which each layer is built upon the previous to produce a green body that can be sintered for a fully dense ceramic part.

This thesis introduces a new approach …

Design, Testing, Analysis, And Material Properties Of Carbon Fiber Reinforced Polymers, Andrew Miner, Simon Jones

Rose-Hulman Undergraduate Research Publications

Rose-Hulman Institute of Technology excels in many fields, however in the field of Carbon Fiber Reinforced Polymers (CFRPs) there is a significant lack of knowledge. Over the 2015 summer I started accumulating and building a knowledge base for the institute to help future students who have interest in this ever expanding field. This report covers many of the learnings I found in the structures of fiber reinforced polymers, manufacturing processes and controls, testing procedures and standards, important considerations in the design process of CFRPs, and analysis capabilities and methods. This report is organized as a series of short guides to …

The Effect Of Cure Rate On Glassy Polymer Networks, Kristen M. Van De Voorde

Honors Theses

The formation of glassy polymer networks such as epoxy-amine systems may be altered by varying the temperature ramp rate that is used to cure the system. As a result, the physical and mechanical properties of the network may be changed. This work synthesized the epoxy resins diglycidyl ether of bisphenol A (DGEBA) with the amine curing agent 4,4-diaminodiphenyl sulfone (4,4’-DDS) from 35°C to 180°C using varying temperature ramp rates. Mechanical and structural properties of these samples were then analyzed to determine the effect the different temperature ramp rates had on the formation and properties of the thermoset matrix. These aspects …

Synthesis Of Acceptors For Use In Donor-Acceptor Copolymers And Characterization Of These Polymers, William D. Walker

Honors Theses

In this thesis, a selenium-derivatized acceptor was synthesized to examine the heavy atom effects of selenium on the position of the frontier molecular orbitals (HOMO/LUMO band gap) as opposed to sulfur in a donor-acceptor copolymer for use in light harvesting and detection applications. Over the course of this research, standard operating protocols for ultraviolet-visible (UV-Vis-NIR) and Fourier transform infrared (FT-IR) spectroscopies, as well as cyclic voltammetry (CV) characterization techniques were established. Once synthesized, the polymers were characterized through use of the established characterization protocols. The selenium-derivatized polymer exhibited a bathochromic shift compared to the sulfur analogue, with a solid-state absorption …

Biopolymeric Mucin And Synthetic Polymer Analogs: Their Structure, Function And Role In Biomedical Applications, Sundar Prasanth Authimoolam, Thomas D. Dziubla

Chemical and Materials Engineering Faculty Publications

Mucin networks are viscoelastic fibrillar aggregates formed through the complex self-association of biopolymeric glycoprotein chains. The networks form a lubricious, hydrated protective shield along epithelial regions within the human body. The critical role played by mucin networks in impacting the transport properties of biofunctional molecules (e.g., biogenic molecules, probes, nanoparticles), and its effect on bioavailability are well described in the literature. An alternate perspective is provided in this paper, presenting mucin’s complex network structure, and its interdependent functional characteristics in human physiology. We highlight the recent advances that were achieved through the use of mucin in diverse areas of bioengineering …

Strain Effects On The Work Function Of An Organic Semiconductor, Yanfei Wu, Annabel R. Chew, Geoffrey A. Rojas, Gjergji Sini, Greg Haugstad, Alex Belianinov, Sergei V. Kalinin, Hong Li, Chad Risko, Jean-Luc Brédas, Alberto Salleo, C. Daniel Frisbie

Chemistry Faculty Publications

Establishing fundamental relationships between strain and work function (WF) in organic semiconductors is important not only for understanding electrical properties of organic thin films, which are subject to both intrinsic and extrinsic strains, but also for developing flexible electronic devices. Here we investigate tensile and compressive strain effects on the WF of rubrene single crystals. Mechanical strain induced by thermal expansion mismatch between the substrate and rubrene is quantified by X-ray diffraction. The corresponding WF change is measured by scanning Kelvin probe microscopy. The WF of rubrene increases (decreases) significantly with in-plane tensile (compressive) strain, which agrees qualitatively with density …

Aging Assessment Of High Voltage Single Component Room Temperature Vulcanized Silicone Rubber (Rtv-1) Subjected To Aqueous Salt, Monika Bleszynski

Electronic Theses and Dissertations

Single component room temperature vulcanized (RTV-1) silicone based caulk used in high voltage insulators and other applications is frequently subjected to environmental pollutants. Aging of RTV-1 silicone rubber is the result of various stressors, including environmental aging conditions such as UV, acid, and salt exposure from ocean mist. Loss of hydrophobicity due to damage of the hydrophobic methyl groups, as well as loss of mechanical strength due to depolymerization via hydrolysis as a result of aqueous salt exposure were the two main factors of material aging assessed in this work. Multiple RTV-1 formulations were initially assessed for resistance to aging …

Eliminating Electromechanical Instability In Dielectric Elastomers By Employing Pre-Stretch, Liang Jiang, Tony Betts, David Kennedy, Stephen Jerrams

Articles

Electromechanical instability (EMI) is one of most common failure modes for dielectric elastomers (DEs). It has been reported that pre-stretching a DE sample can suppress EMI due to strain stiffening taking place for larger strains and a higher elastic modulus are achieved at high stretch ratios when a voltage is applied to the material. In this work, the influence of equi-biaxial stretch on DE secant modulus was studied using VHB 4910 and silicone rubber (SR) composites containing barium titanate (BaTiO3, BT) particles and also dopamine coated BT (DP-BT) particles. The investigation of equi-biaxial deformation and EMI failure for VHB 4910 …

Power Maximization For Pyroelectric, Piezoelectric, And Hybrid Energy Harvesting, Murtadha A. Shaheen

Theses and Dissertations

The goal of this dissertation consists of improving the efficiency of energy harvesting using pyroelectric and piezoelectric materials in a system by the proper characterization of electrical parameters, widening frequency, and coupling of both effects with the appropriate parameters.

A new simple stand-alone method of characterizing the impedance of a pyroelectric cell has been demonstrated. This method utilizes a Pyroelectric single pole low pass filter technique, PSLPF. Utilizing the properties of a PSLPF, where a known input voltage is applied and capacitance C_p and resistance R_p can be calculated at a frequency of 1 mHz to 1 Hz. …

Equi-Biaxial Fatigue Behaviour Of Magnetorheological Elastomers In Magnetic Fields, Yanfen Zhou, Mark Johnson, Shipeng Wen, Tony Betts, Stephen Jerrams

Articles

The equi-biaxial fatigue behaviour of silicone based magnetorheological elastomers (MREs) in external magnetic fields was studied. Wöhler curves relating fatigue life to stress amplitude and dynamic stored energy for MREs with a range of magnetic particle contents were derived. It was found that the fatigue life of MREs in magnetic fields was higher than that without magnetic fields. Under constant stress amplitude conditions, the presence of magnetic fields resulted in longer times for the samples to undergo large deformations and thus complex modulus (E*) decreased at a slower rate during the fatigue process, especially for low stress amplitudes. MRE samples …

Mechanical Testing Of Fused Filament 3-D Printed Components For Distributed Manufacturing, Nagendra Gautam Tanikella

Dissertations, Master's Theses and Master's Reports

Fused filament fabrication (FFF)-based open-source 3-D printers offer the potential of decentralized manufacturing both in developing and developed countries. Unfortunately, a severe lack of data and standards relating to material properties and printed components limit this potential. This thesis first investigates the mechanical properties of a wide-range of FFF materials and provides a database of mechanical strength of the materials tested. The results demonstrate that the tensile strength of a 3-D printed specimen depends largely on the mass of the specimen, which provides a means to estimate the strength of 3-D printed components. Then this information is used to evaluate …

Bioluminescent Magnetic Nanoparticles As Potential Imaging Agents For Mammalian Spermatozoa, Erick Salvador Vasquez, Jean M. Feugang, Scott T. Willard, Peter L. Ryan, Keisha B. Walters

Chemical and Materials Engineering Faculty Publications

Background: Nanoparticles have emerged as key materials for developing applications in nanomedicine, nanobiotechnology, bioimaging and theranostics. Existing bioimaging technologies include bioluminescent resonance energy transfer-conjugated quantum dots (BRET-QDs). Despite the current use of BRET-QDs for bioimaging, there are strong concerns about QD nanocomposites containing cadmium which exhibits potential cellular toxicity.

Results: In this study, bioluminescent composites comprised of magnetic nanoparticles and firefly luciferase (Photinus pyralis) are examined as potential light-emitting agents for imaging, detection, and tracking mammalian spermatozoa. Characterization was carried out using infrared spectroscopy, TEM and cryo-TEM imaging, and ζ-potential measurements to demonstrate the successful preparation of these nanocomposites. Binding …

Evaluation Of Flocculation, Sedimentation, And Filtration For Dewatering Of Algal Biomass, Nicholas A. Rhea

Theses and Dissertations--Biosystems and Agricultural Engineering

Algae can be used as a feedstock for agricultural fertilizers, livestock/poultry feeds, anaerobic digestion, and biofuel production. Regardless of the end product, water removal is necessary and difficult to do cost effectively. For each product the requirements for moisture content (or solids content) vary, such that a desirable water removal strategy would need to be adaptable to varying levels of water removal. Flocculation, with sedimentation and drying was evaluated as a possible strategy for algae dewatering. Anionic and nonionic flocculants are known to be ineffective at flocculating algal culture, which was confirmed for this case by electro-osmotic flow testing of …

Experimental Investigations Of Fused Filament Fabrication For Applications To Affordable Scientific Hardware, Bas Wijnen

Dissertations, Master's Theses and Master's Reports

This research aims to make science more accessible through the use of open source 3-D printers.

A new control system for CNC machines in general and 3-D printers specifically, is developed and presented that enables web-based control of 3-D tools from any Internet connected device. The system can be set up and controlled entirely from a web interface.

A tool was designed to help apply science to the developing world. The developing world remains plagued by lack of access to safe drinking water. A methodology is provided for the design, development, and technical validation of a low-cost open-source water testing …

The Role Of Microbial Exopolymers In Determining The Fate Of Oil And Chemical Dispersants In The Ocean, Antonietta Quigg, Uta Passow, Wei-Chun Chin, Chen Xu, Shawn Doyle, Laura Bretherton, Manoj Kamalanathan, Alicia K. Williams, Jason B. Sylvan, Zoe V. Finkel, Anthony H. Knap, Kathleen A. Schwehr, Saijin Zhang, Luni Sun, Terry L. Wade, Wassim Obeid, Patrick G. Hatcher, Peter H. Santschi

Chemistry & Biochemistry Faculty Publications

The production of extracellular polymeric substances (EPS) by planktonic microbes can influence the fate of oil and chemical dispersants in the ocean through emulsification, degradation, dispersion, aggregation, and/or sedimentation. In turn, microbial community structure and function, including the production and character of EPS, is influenced by the concentration and chemical composition of oil and chemical dispersants. For example, the production of marine oil snow and its sedimentation and flocculent accumulation to the seafloor were observed on an expansive scale after the Deepwater Horizon oil spill in the Northern Gulf of Mexico in 2010, but little is known about the underlying …

Developing The Stress Strain Curves For An Epoxy Undergoing High Speed Impact, Stanford L. Howdyshell 7867559

Williams Honors College, Honors Research Projects

The Hopkinson Split Bar test can be used to accurately develop the relationship between the stress and strain a material undergoes during a high speed impact (rates of 1000/s). This information has many industrial uses, for example the auto industry can use this technology to analyze how materials will behave under crash-like circumstances. In this experiment the stress-strain curves were developed for the PC-Plumbing epoxy.

One of the variables that can be adjusted in the Split Hopkinson Bar test is the ration between the height of the sample and the width of the sample (Hs/Ds). This experiment investigated how three …

Diffusive Behavior Of Physically Cross-Linked Hydrogels, Morgan A. Stilke

Williams Honors College, Honors Research Projects

A hydrogel is a water swollen polymeric network that has the potential to transform a variety of biomedical applications because of its biocompatibility and water content. Unfortunately, hydrogels typically have poor mechanical robustness. The majority of the content is water, while the remaining structure consists of a physical network, a covalent network, or a combination of both, yielding strength and toughness. There are several strategies attempted to improve mechanical properties including double network hydrogels comprised of two interpenetrating networks: one being a highly crosslinked sacrificial network and the other being a weakly crosslinked network that maintains reversibility after deformation. However, …

Optimizing Solvent Blends For A Quinary System, Thomas L. Hoy

Williams Honors College, Honors Research Projects

The Department of Polymer Engineering had received a grant from the Keck foundation to produce a process in which hundreds of copolymers can be formulated, synthesized, analyzed and then extrapolated to produce the optimal polymer for the desired material property. This process involves synthesizing approximately fifty polymers in a custom apparatus, none of which necessarily have the same monomer components. This leads to issue of which solvent or blend of solvents to use that would sufficiently dissolve both monomers and the resulting copolymer. If the monomers are not completely dissolved, a homogenous reaction will be impossible and if the copolymer …

Bioactive Poly(Beta-Amino Ester) Biomaterials For Treatment Of Infection And Oxidative Stress, Andrew L. Lakes

Theses and Dissertations--Chemical and Materials Engineering

Polymers have deep roots as drug delivery tools, and are widely used in clinical to private settings. Currently, however, numerous traditional therapies exist which may be improved through use of polymeric biomaterials. Through our work with infectious and oxidative stress disease prevention and treatment, we aimed to develop application driven, enhanced therapies utilizing new classes of polymers synthesized in-house. Applying biodegradable poly(β-amino ester) (PBAE) polymers, covalent-addition of bioactive substrates to these PBAEs avoided certain pitfalls of free-loaded and non-degradable drug delivery systems. Further, through variation of polymer ingredients and conditions, we were able to tune degradation rates, release profiles, cellular …

Synthesis Of Titania Thin Films With Controlled Mesopore Orientation: Nanostructure For Energy Conversion And Storage, Suraj R. Nagpure

Theses and Dissertations--Chemical and Materials Engineering

This dissertation addresses the synthesis mechanism of mesoporous titania thin films with 2D Hexagonal Close Packed (HCP) cylindrical nanopores by an evaporation-induced self-assembly (EISA) method with Pluronic surfactants P123 and F127 as structure directing agents, and their applications in photovoltaics and lithium ion batteries. To provide orthogonal alignment of the pores, surface modification of substrates with crosslinked surfactant has been used to provide a chemically neutral surface. GISAXS studies show not only that aging at 4°C facilitates ordered mesostructure development, but also that aging at this temperature helps to provide orthogonal orientation of the cylindrical micelles which assemble into an …

First-Principles Studies Of Structure-Property Relationships: Enabling Design Of Functional Materials, Qunfei Zhou

Theses and Dissertations--Chemical and Materials Engineering

First-principles calculations based on quantum mechanics have been proved to be powerful for accurately regenerating experimental results, uncovering underlying myths of experimental phenomena, and accelerating the design of innovative materials. This work has been motivated by the demand to design next-generation thermionic emitting cathodes and techniques to allow for synthesis of photo-responsive polymers on complex surfaces with controlled thickness and patterns. For Os-coated tungsten thermionic dispenser cathodes, we used first-principles methods to explore the bulk and surface properties of W-Os alloys in order to explain the previously observed experimental phenomena that thermionic emission varies significantly with W-Os alloy composition. Meanwhile, …

Equi-Biaxial Fatigue Testing Of Epm Utilising Bubble Inflation, Mark Johnson, Niall Murphy, Ray Ekins, John Hanley, Stephen Jerrams

Articles

This paper describes an equi-biaxial tension fatigue test system which utilises the bubble inflation method to subject elastomers to equi-biaxial fatigue loading between user-defined limits of pressure, volume, stretch ratio or stress. The test system integrates a hydraulic inflation system, a high speed vision system and a control system. The high-speed vision system allows the stretch ratio and stress acting on the test specimen to be evaluated in real-time during testing. This in turn allows either stretch ratio or stress to be used as a direct control limit. In this research, constant maximum engineering stress control tests have been carried …

Inhibition Of Bacterial Growth And Prevention Of Bacterial Adhesion With Localized Nitric Oxide Delivery, Julia Osborne

Dissertations, Master's Theses and Master's Reports

Bacterial infections continue to be a problem at the site of an indwelling medical device, and over the years, various bacterial strains have become more resistant to current antibiotic treatments. Bacterial infection at an indwelling medical device can be dangerous and affect the performance of the medical device which can ultimately lead to the failure of the device due to bacterial resistance to treatment.

Nitric Oxide (NO) has been shown to possess antibacterial properties to prevent and inhibit bacterial growth. NO releasing coatings on indwelling medical devices could provide a reduction in bacterial infections that occur at the device site …

A Platform For Fast Detection Of Let-7 Micro Rna Using Polyaniline Fluorescence And Image Analysis Techniques, Partha P. Sengupta

Master's Theses

The project describes a new strategy for transducing hybridization events through modulating intrinsic properties of the electroconductive polymer polyaniline (PANI). When DNA based probes electrostatically interact with PANI, its fluorescence properties are increased, a phenomenon that can be enhanced by UV irradiation. Hybridization of target nucleic acids results in dissociation of probes causing PANI fluorescence to return to basal levels. By monitoring restoration of base PANI fluorescence as little as 10^-11 M (10 pM) of target oligonucleotides could be detected within 15 minutes of hybridization. Detection of complementary oligos was specific, with introduction of a single mismatch failing to …

Effects Of Expected Service Life Exposures On The Functional Properties And Impact Performance Of An American Football Helmet Outer Shell Material, David E. Krzeminski

Dissertations

The purpose of this dissertation is to gain a greater scientific understanding of the changes in functional material properties and impact performance of an American football helmet outer shell material under expected service life exposures. The research goals are to (i) quantify chemical, physical, thermal, and mechanical degradation of an American football outer shell material under expected environmental conditions and (ii) develop a linear drop test impact protocol to employ expected on-field impact conditions to American football helmet components and a plaque-foam (i.e., shell-liner) surrogate. Overall, a step-wise progression of analysis was demonstrated to concurrently quantify and understand changes in …

Hybrid Aryl-Ether-Ketone And Hyperbranched Epoxy Networks, John Misasi

Dissertations

In this dissertation, relationships between chemical structures, cure kinetics and network architectures are correlated to bulk mechanical properties for novel, hybrid epoxy-amine networks. The work is split into two primary sections: the first is the synthesis and characterization of multifunctional glassy networks based on aryl-ether-ketone diamine curatives, while the second is based on the synthesis and characterization of hyperbranched epoxy polymers and their resulting networks.

Three aryl-ether-ketone (AEK) diamines of increasing molecular weights were synthesized and used to cure 4,4’-tetraglycidylether of diaminodiphenylmethane (TGDDM); the resulting networks were compared to 4,4’-diaminodiphenyl sulfone cured TGDDM. Architectural differences were created by varying cure …