Polymer and Organic Materials Commons^™

Enabling Assembly And Repair Of Dissimilar Thermoplastic Composites For Space Applications Via Ultrasonic Welding, Emily Nicole Friedman

LSU Master's Theses

Interest in the repair and reuse of thermoplastic composites (TPCs) is growing, especially for lightweight space/lunar structures. Ultrasonic welding (USW) is a promising joining technique by which vibration is applied to create heat. An energy director (ED) is used at the joint interface to concentrate heat generation to the desired surface. This work explores the effect of dissimilar ED materials on the disassembly repair of TPCs using USW, to potentially tailor weld properties for specific applications. Single lap joints were created using carbon fiber (CF)/polyether ether ketone (PEEK) adherends with PEEK, polyphenylene sulfide (PPS), polyetherimide (PEI), and low melt polyaryletherketone …

Development Of Multifunctional Wood Composites With Integrated Phase Change Materials For Enhanced Thermal Management, Self-Healing, And Sustainability., Emmanuel Igbokwe

LSU Master's Theses

Abstract

This study focused on incorporating self-healing, flame retardancy, and energy harvesting capabilities into the wood composite to contribute to more sustainable and energy-efficient building practices. Oriented strand board has been widely used as sheath for roofing or dry walls in residential buildings. Residential buildings account for a large portion of energy consumption. Therefore, an oriented strand board with energy harvesting capability is highly desired. Additionally, flame retardancy and damage self-healing and end-of-life recycling are also critical features for buildings.

In this study, we prepared a novel oriented strand board by constructing sandwich structures. The face sheets of the sandwich …

A Machine Learning Approach To Robotic Additive Manufacturing Of Uv-Curable Polymers Using Direct Ink Writing, Luis A. Velazquez

LSU Master's Theses

This thesis presents the design and implementation of a robotic additive manufacturing system that uses ultraviolet (UV)-curable thermoset polymers. Its design considers future applications involving free-standing 3D printing by means of partial UV curing and the fabrication of samples that are reinforced with fillers or fibers to manufacture complex-shape objects.

The proposed setup integrates a custom-built extruder with a UR5e collaborative manipulator. The capabilities of the system were demonstrated using Anycubic resin formulations containing fumed silica (FS) at varying weight fractions from 2.8 to 8 wt%. To fully cure the specimens after fabrication, a UV chamber was used. Then, measurements …

Predictive Thermal Modeling And Characterization Of Ultrasonic Consolidation Process For Thermoplastic Composites, Madeline Kirby

LSU Master's Theses

Ultrasonic consolidation (USC) of thermoplastic composites (TPCs) is a highly attractive and promising method to manufacture high-performance composites. This work focuses on USC of dry carbon fiber (CF) fabrics with high-temperature polyphenylene sulfide (PPS) films. Experimental trials to assess feasibility of the process are time-consuming. Consequently, a predictive thermal model would facilitate process parameters selection to reduce expensive trial-and-error approaches. This paper presents a 2D finite element model of samples under consolidation, incorporating equations for viscoelastic heating, matrix phase change, and material properties. Theoretical temperature profiles for nodes of interest were compared to the corresponding experimental temperature curves for various …

Degumming Of Hemp Fibers Using Combined Microwave Energy And Deep Eutectic Solvent, Bulbul Ahmed

LSU Master's Theses

Hemp is considered as one of the sustainable agricultural fiber materials. Degumming or surface modification of hemp bast is needed to produce single fibers for ensuing textile and industrial applications. The traditional degumming process necessitates a high amount of alkali, which causes detrimental environmental pollution. This study offers a new method to degum hemp fibers with reduced use of harmful alkali and precious water resources. In this work, hemp bast fibers were degummed by using combined microwave energy and deep eutectic solvent (DES). The properties of hemp fibers manufactured by this method were investigated and compared with the traditional alkali …

An Investigation Of High-Speed Consolidation And Repair Of Carbon Fiber - Epoxy Composites Through Ultrasonic Welding, David A. Hoskins

LSU Master's Theses

Adhesive repair of carbon fiber composite structures is commonly done on damaged structures to extend the service life. This method requires careful preparation of the damaged surface with intricate steps to ensure good bonding between the repair patch and the parent structure by means of an adhesive film. As with many forms of composite manufacturing, it is required to perform vacuum bagging, debulking, and a heated cure depending on the resin. All these steps make the repair process costly and time consuming.

In this present work, an alternative method of repair is investigated which explores the experimental feasibility of using …

A Systematic Investigation Of Condensation Heat Transfer Using Asymmetric Micro-Scale Surfaces, Emily Brown

LSU Master's Theses

Asymmetric surfaces been shown to inducing unidirectional motion in the Leidenfrost regime; however, very minimal research has been conducted to investigate whether these surface can enhance condensation through the same means. The investigation of heat transfer of ratchets in condensation is a relatively untapped area of study, specifically ratchets with superhydrophobic properties. Anticipated difficulty lies in creating surfaces features or coatings that retain the ratchets and can adequately sustain optimal wetting state of Cassie-Baxter required to improve heat transfer performance during condensation. This study serves to investigate whether ratchets are a feasible surface feature to enhance condensation heat transfer. First, …

Synthesis And Characterization Of Polyaniline Agglomerates And Polyaniline Nanoparticles To Use As Printed Sensors To Detect Spoilage Of Catfish During Refrigerated Storage, Vashti Martae Campbell

LSU Master's Theses

There is growing interest in the development of sensors contained in packaging for seafood that are applicable at the consumer level to monitor freshness in a non-destructive manner. Total volatile basic nitrogen (TVB-N) analysis indicates the freshness of seafood. TVB-N analysis is sensitive to the spoilage compounds comprised of ammonia, trimethylamine, dimethylamine, and biogenic amines commonly found in seafood and whose concentration increases when spoilage microbial growth occurs. However, TVB-N analysis is laborious and is not suitable for use at the consumer level. Polyaniline (PANI) is a polymer that may be used as a sensor for detecting TVB-N in seafood. …

Waste Management By Waste: Removal Of Acid Dyes From Wastewaters Of Textile Coloration Using Fish Scales, S M Fijul Kabir

LSU Master's Theses

Removal of hazardous acid dyes by economical process using low-cost bio-sorbents from wool industry wastewaters is of a pressing need, since it causes skin and respiratory diseases and disrupts other environmental components. Fish scales (FS), a by-product of fish industry, a type of solid waste, are usually discarded carelessly resulting in pungent odor and environmental burden. In this research, the FS of black drum (Pogonias cromis) were used for the removal of acid dyes (acid red 1 (AR1), acid blue 45 (AB45) and acid yellow 127 (AY126)) from wool industry wastewaters by absorption process with a view to …