Polymer and Organic Materials Commons^™

Development Of Hybrid Self-Cleaning Coating Using Lanthanide-Based Light Spectral Response Material To Enhance Photovoltaic (Pv) Panel Efficiency In Operational Environment, Khishn Kumar Kandiah

Student Works (2020-2029)

The efficiency of photovoltaic (PV) panels is crucial, as solar energy has become an alternative energy source that meets today’s global energy demands. Hence, dust accumulation and spectral mismatch have major effects on the efficiency of PV panels, around 20 %, but in extreme situations, this can reach up to 64 %. Therefore, initiatives are underway to address these issues, including PV cooling systems, conventional cleaning methods, and various coatings to enhance efficiency. In this work, a novel coating is fabricated with high transparency, excellent self-cleaning properties, and good spectral-modifying properties. Two types of powder composites are employed in this …

Polymer Microstructures For Advanced Biomanufacturing, Tongyao Wu

LSU Doctoral Dissertations

With the continued growth of the biopharmaceutical industry, the demand for scalable, robust, and resource-efficient platforms for large-scale mammalian cell culture is amplified. Recent developments in microfluidic technology, such as precise control of the microenvironment, showed the potential to improve the performance of cell culture systems. However, constrained by scalability and operational efficiency, applying such approaches to large-scale cell culture and biopharmaceutical production presents challenges. This dissertation addresses these challenges through three independent but conceptually related technological developments. First, a roll-to-roll (R2R) fabrication process was developed for the scalable production of hollow microcarriers (HMCs). HMCs provide three-dimensional microenvironments suitable for …

Bridging Physics-Based Modeling And Machine Learning To Predict Material Behavior: Applications In Fatigue Crack Growth And Dielectric Property Characterization, Ansan Pokharel

Graduate Theses, Dissertations, and Problem Reports (ETD)

This dissertation integrates physics-based modeling with machine learning (ML) to predict how materials behave under complex thermal and mechanical conditions. A key innovation of this work is the use of finite element analysis (FEA) to supplement experimental data. This approach creates more diverse and representative synthetic datasets, helping to reduce the limitations and biases that arise when training ML models solely on experimental measurements. The research focuses on two applications: improving the prediction of fatigue properties in superalloys and estimating temperature-dependent, high-frequency dielectric properties relevant to microwave-based chemical processing.

In the first study, low-cycle fatigue experiments were performed on the …

Self-Poled P(Vdf-Trfe) Based Composites For Energy Harvesting And Wearable Sensor Applications, Lavanya Muthusamy

All Dissertations

The growing demand for flexible, low-power, and self-powered wearable electronic systems has accelerated research interest in polymer-based sensors and energy harvesting technologies. Among piezoelectric polymer materials, Poly(vinylidene fluoride-trifluoro ethylene) [P(VDF-TrFE)], over the years, has garnered significant attention due to its unique piezoelectric properties, high dielectric constant, mechanical flexibility, thermal stability, chemical resistance, biocompatibility and compatibility with scalable fabrication processes. Despite its advantages, conventional P(VDF-TrFE)-based devices often require external poling and face limitations in integration with low-cost, flexible substrates. To overcome these limitations, this research study explores the nanofiller approach, along with facile fabrication processes, and structural design strategies aimed at …

Nanomaterial-Enabled Enhancements In Thylakoid-Based Biofuel Cells, Amit Sarode, Gymama Slaughter

Center for Bioelectronics Publications

Thylakoid-based photosynthetic biofuel cells (TBFCs) harness the inherent light-driven electron transfer pathways of photosynthesis to enable sustainable solar-to-electrical energy conversion. While TBFCs offer a unique route toward biohybrid energy systems, their practical deployment is hindered by sluggish electron transfer kinetics, unstable redox mediators, and inefficient interfacing between biological and electrode components. This review critically examines recent advances in TBFCs, with a focus on three key surface engineering strategies: (i) incorporation of nanostructured materials to enhance electrode conductivity and surface area; (ii) application of redox mediators to facilitate charge transfer between photosynthetic proteins and electrodes; and (iii) functional exploitation of individual …

A Comprehensive Review Of Piezoelectric Pvdf Polymer Fabrications And Characteristics, Nadia Ahbab, Sidra Naz, Tian-Bing Xu, Shihai Zhang

Mechanical & Aerospace Engineering Faculty Publications

Polyvinylidene fluoride (PVDF) polymer films, renowned for their exceptional piezoelectric, pyroelectric, and ferroelectric properties, offer a versatile platform for the development of cutting-edge micro-scale functional devices, enabling innovative applications ranging from energy harvesting and sensing to medical diagnostics and actuation. This paper presents an in-depth review of the material properties, fabrication methodologies, and characterization of PVDF films. Initially, a comprehensive description of the physical, mechanical, chemical, thermal, electrical, and electromechanical properties is provided. The unique combination of piezoelectric, pyroelectric, and ferroelectric properties, coupled with its excellent chemical resistance and mechanical strength, makes PVDF a highly valuable material for a wide …

Refining Chlorosulfonation Methods For The Synthesis Of A Perfluoroalkyl Arylsulfonimide (Pfsi) Monomer, Ainsley P. Foster, Benjamin Varney, Hua Mei

Science University Research Symposium (SURS)

Proton-exchange membrane (PEM) fuel cells are sources of energy that are clean, quiet, and highly responsive to changes in power needs, making them promising for use in automobiles and other portable power devices. The electrolyte of a PEM cell–the layer responsible for conductivity–is a polymer membrane, commonly consisting of perfluoroalkyl sulfonic acid (PFSA) polymers. Perfluoroalkyl arylsulfonimide (PFSI) polymers are expected to improve the efficiency of PEM fuel cells through optimal stability and proton conductivity. The trifluovinylether (TFVE) aryl perfluorosulfonamide monomer is a new PFSI monomer proposed to fulfill these benefits once polymerized. A six-step synthesis route was initially designed to …

Development And Processing Of Shape Memory Polymer Composites (Smpcs) For Application In Structural Robotics And Robotic Sensors., Kavish Sudan

Electronic Theses and Dissertations

Shape Memory Polymers (SMPs) have attracted significant attention since their introduction in the 1980s due to their remarkable ability to regain their original shape from a temporarily deformed state when exposed to an external stimulus, typically heat. This shape memory effect, driven by thermal transitions such as the glass transition temperature (T_g) or melting temperature (T_m), has made SMPs highly attractive for applications in soft robotics, aerospace, and biomedical devices. However, SMPs face challenges such as limited mechanical strength, thermal stability, and electrical conductivity, which hinder their broader adoption in advanced applications. To address these challenges, …

Surface Treatments' Effects On The Capacitor's Dielectric Performance Under Electro-Thermal Stresses, Haider. M. Umran, Feipeng Wang

Karbala International Journal of Modern Science

Biaxial-oriented polypropylene (BOPP) films are characterized by unfavorable aging behavior because of their poor susceptibility to high temperatures, humidity, and high electric fields. This makes them unqualified to withstand harsh operating conditions, such as in capacitor applications. This study investigates the impact of annealing BOPP samples at 100 °C for five hours after fluorination at different times (15, 30, and 60 minutes) on their electrical and mechanical performance under electro-thermal stresses. Scanning electron microscope (SEM) images confirm that there is an increase in surface roughness and the formation of a dense layer of fluorine-containing groups monotonically with fluorination time. So, …

Low Impedance, Durable, Self-Adhesive Hydrogel Epidermal Electrodes For Electrophysiology Recording, Naiyan Wu

McKelvey School of Engineering Graduate Student Theses & Dissertations

Traditional electrodes used for electrophysiology recording, characterized by their hard, dry, and inanimate nature, are fundamentally mismatched with the soft, moist, and bioactive characteristics of biological tissues, leading to suboptimal skin-electrode interfaces. Hydrogel materials, mirroring the high water content and biocompatibility of biological tissues, emerge as promising candidates for epidermal electronic materials due to their adjustable physicochemical properties. However, challenges such as inadequate electrical conductivity, elevated skin impedance, unreliable adhesion in moist conditions, and performance decline from dehydration have significantly restricted the efficacy and applicability of hydrogel-based electrodes. In this thesis, we report a high-performance hydrogel epidermal electrode patch for …

Schaeffler Icvd Coating Machine, Louis Mcgrath

Williams Honors College, Honors Research Projects

Chemical Vapor Deposition (CVD) is mutual technology used to deposit thin film through a gaseous phase by vaporizing the solid materials. This conventional process usually requires high thermal stability of the materials, which is not applicable for most of the polymeric materials. Therefore, a novel process, initiated Chemical Vapor Deposition (iCVD) is developed by introducing the gaseous monument and initiator to form the thin film in-situ. By adjusting the free-radical polymerization in the vapor phase, a variety of thin and uniform polymer films can be achieved. Depending on the chemistry, iCVD has many categories. This report explains the design …

Functional Verification Of Additively Manufactured Metallopolymer Structures For Structural Electronics Design, Nathan D. Singhal

Honors Undergraduate Theses

As an attempt to improve the overall cost-effectiveness and ease of structural electronics manufacturing, this study characterizes the mechanical and electrical responses of structures which are fabricated from a novel metallopolymer composite material by fused deposition modeling as they are subjected to quasi-static, uniaxial mechanical tension. Baseline values of tensile properties and electrical resistivity were first obtained via ASTM D638-22 standard testing procedures and linear sweep voltammetry (LSV), respectively. A hybrid procedure to measure in-situ mechanically dependent electrical behavior was subsequently developed and implemented. The mechanical and electromechanical testing was followed by the derivation of stochastic values for several mechanical …

Design, Fabrication And Characterization Of Zero Power Sensor/Harvester For Smart Grid Applications, Zeynel Guler

Mechanical Engineering ETDs

This study presents a flexible sensor/harvester device to be used in both electromagnetic sensing and energy harvesting applications for smart grids. When a current passes through a wire, the sensor detects the magnetic field created by that current. The sensor magnet interacts with the wire magnetic field resulting in a transfer of energy through the piezoelectric cantilever. Piezoelectric, conductive, magnetic, and magnetostrictive composite thin films were prepared to fabricate this device.

Initially, the magnet of the cantilever was optimized considering its shape, thickness, length, taper angle etc. via both simulations and experiments. Peak to peak voltage versus cantilever position graph …

Piezoelectric And Conductive Polymer Based Flexible Devices Enabling Cardiovascular Health Sensing And Energy Harvesting, Andrew Closson

Dartmouth College Ph.D Dissertations

Piezoelectric materials show great promise for low-power wearable and implantable sensing, but their rigidity makes it challenging to integrate them with biological tissue. To address this, researchers have started exploring polymer-based functional materials that offer flexibility and are suitable for interfacing with the human body. However, these materials are still in their early stages, and a framework is necessary to illustrate how these materials, in conjunction with novel fabrication techniques and device designs, can enable the development of multi-functional sensing and energy harvesting devices.

This thesis utilizes highly scalable fabrication methods for functional polymers to build and test a flexible …

Enhancing The Performance Of Poly(3-Hexylthiophene) Based Organic Thin-Film Transistors Using An Interface Engineering Method, Eyob Negussie Tarekegn

All Dissertations

An original design and photolithographic fabrication process for poly(3-hexylthiophene-2, 5-diyl) (P3HT) based organic thin-film transistors (OTFTs) is presented. The structure of the transistors was based on the bottom gate bottom contact OTFT. The fabrication process was efficient, cost-effective, and relatively straightforward to implement. Current–voltage (I-V) measurements were performed to characterize the primary electronic properties of the transistors. The measured mobility of these transistors was significantly higher than most results reported in the literature for other similar bottom gate bottom contact P3HT OTFTs. The higher mobility is explained primarily by the effectiveness of the fabrication process in keeping the interfacial layers …

Photon Attenuation Layer Silicon-Based X-Ray Detector: Quantum Efficiency Investigation And Algorithmic Processing Of Individual Detection Events, Kevin Larkin

ENGS 88 Honors Thesis (AB Students)

State-of-the-art X-ray detectors either use silicon direct detection—which is inefficient, as silicon is mostly transparent to high-energy X-rays—or rely on expensive scintillators to first down-convert X-ray photons to lower energies. Dr. Eldred Lee of Dartmouth College recently completed doctoral research that suggested the promise of a novel alternative: silicon-based X-ray detectors that utilize photon attenuation layers rather than scintillators. While Dr. Lee’s work is certainly rigorous and meritorious, background noise controls were rendered less effective by circumstances. The work presented in this thesis succeeded in implementing much better background noise controls for a series of new tests to compare the …

Receptor-Doped Organic Transistors: Transducing Anion Binding From Mixed Ionic-Electronic Transport, Anthony Benasco

Dissertations

Organic semiconductors based on π-conjugated polymers show remarkable properties such as high tolerance to structural defects, low processing temperature requirements, biocompatibility, ease of fabrication, and tunable properties. Conjugated polymers integrated into device arrays can exhibit collective properties sensitive to minor perturbations in the surrounding media. However, these devices rely on serendipitous sensitivity to the analyte of interest, and strategies for specific detection remain a considerable change. There remains a compelling, global need for technologies to monitor phosphate due to its prevalence in agricultural runoff, leading to fish kills and economic decline for commercial and recreational fisheries. The strong hydration energies …

Electromechanical Fatigue Properties Of Dielectric Elastomer Stretch Sensors Under Orthopaedic Loading Conditions, Andrea Karen Persons

Theses and Dissertations

Fatigue testing of stretch sensors often focuses on high amplitude, low-cycle fatigue (LCF) behavior; however, when used for orthopaedic, athletic, or ergonomic assessments, stretch sensors are subjected to low amplitude, high-cycle fatigue (HCF) conditions. As an added layer of complexity, the fatigue testing of stretch sensors is not only focused on the life of the material comprising the sensor, but also on the reliability of the signal produced during the extension and relaxation of the sensor. Research into the development of a smart sock that can be used to measure the range of motion (ROM) of the ankle joint during …

Spray Deposition Of Sustainable Plant Based Graphene In Thermosetting Carbon Fiber Laminates For Mechanical, Thermal, And Electrical Properties, Daniel W. Mulqueen, Siavash Sattar, Thienan Le, Oleksandr G. Kravchenko

Mechanical & Aerospace Engineering Faculty Publications

Graphene has generated substantial interest as a filler due to its exceptional strength, flexibility, and conductivity but faces obstacles in supply and implementation. A renewable, plant-based graphene nanoparticle (pGNP) presents a more accessible filler with the same properties as mineral graphenes. In this study, we examine the effects of pGNP, which was sprayed on a carbon fiber/epoxy prepreg at loadings from 1.1 to 4.2 g/m². The study considered the mechanical, thermal, and electrical properties of pGNP-composite. An even particle dispersion was achieved using a spray application of pGNP in a water/alcohol suspension with the addition of surfactants and …

Modeling, Fabrication, And Characterization Of Rf-Based Passive Wireless Sensors Composed Of Refractory Semiconducting Ceramics For High Temperature Applications, Kavin Sivaneri Varadharajan Idhaiam

Graduate Theses, Dissertations, and Problem Reports (ETD)

Real-time health monitoring of high temperature systems (>500^oC) in harsh environments is necessary to prevent catastrophic events caused by structural failures, varying pressure, and chemical reactions. Conventional solid-state temperature sensors such as resistance temperature detectors (RTDs) and thermocouples are restricted by their operating environments, sensor dimensions and often require external power sources for their operation. The current work presents the research and development of RF-based passive wireless sensing technology targeting high temperatures and harsh environmental conditions. Passive wireless devices are generally classified as near-field and far-field devices based on the interrogation distance. Near-field sensors are placed at …

Effect Of Freestream Noise On Hypersonic Crossflow-Induced Boundary-Layer Transition, Andrew Bustard, Thomas J. Juliano, Harrison B. Yates, Mark Noftz, Joseph Jewell

Publications

Between the windward and leeward rays, boundary-layer transition on cones at angle of attack in hypersonic flow is dominated by the crossflow instability [1, 2], wherein stationary and/or traveling crossflow vortices develop and can breakdown into turbulence [3]. Stationary crossflow modes are caused by surface roughness or any other steady forcing and produce disturbances that are fixed in place on the surface [3–6]. Stationary vortices create a generalized inflection point in the velocity profile that is inviscidly unstable [7]. This distorted mean flow develops secondary instabilities, whose growth and breakdown is one path to turbulence [8–10]. Traveling crossflow modes are …

Investigation Of Optical And Structural Properties Of Gesn Heterostructures, Oluwatobi Gabriel Olorunsola

Graduate Theses and Dissertations

Silicon (Si)-based optoelectronics have gained traction due to its primed versatility at developing light-based technologies. Si, however, features indirect bandgap characteristics and suffers relegated optical properties compared to its III-V counterparts. III-Vs have also been hybridized to Si platforms but the resulting technologies are expensive and incompatible with standard complementary-metal-oxide-semiconductor processes. Germanium (Ge), on the other hand, have been engineered to behave like direct bandgap material through tensile strain interventions but are well short of attaining extensive wavelength coverage. To create a competitive material that evades these challenges, transitional amounts of Sn can be incorporated into Ge matrix to form …

Investigation Of Membrane Based Processes For Biomedical Applications, Efecan Pakkaner

Graduate Theses and Dissertations

As substantial developments were achieved in nanotechnology and polymer engineering, especially in the last few decades, the use of membranes and membrane-based procedures was found to be expanding into more and more research and development areas; including biological engineering, life sciences and biomedical engineering. Not only have they been the main focus of meaningful research, but they have also been the main pieces of the solutions to very thorny problems encountered within a wide range of applications from microfluidics to water treatment, thanks to their versatility, cost-effectiveness and biocompatibility, when compared to conventional separation techniques. To celebrate and embrace these …

Characterization Of Gesn Semiconductors For Optoelectronic Devices, Hryhorii Stanchu

Graduate Theses and Dissertations

Germanium-tin alloys with Sn compositions higher than 8 at. % to 10 at. % have recently attracted significant interest as a group IV semiconductor that is ideal for active photonics on a Si substrate. The interest is due to the fact that while at a few percent of Sn, GeSn is an indirect bandgap semiconductor, at about 8 to 10 at. % Sn, GeSn transitions to a direct bandgap semiconductor. This is at first surprising since the solid solubility of Sn in Ge under equilibrium growth conditions is limited to only about 1 at. %. However, under non-equilibrium growth conditions, …

Oxone® Mediated Tempo-Oxidized Cellulose Nanomaterials: Material Characterization, Ultrafiltration Membrane Separations, And Thin Film Composite Gas Transport Analysis, John Phillips Moore

Graduate Theses and Dissertations

Cellulose nanomaterials (CNMs) are derived from plant matter and are comprised of nanoscopic cellulose crystals and fibers. They have a diverse set of applications, from cosmetics to oil recovery. This study focuses on the properties of Oxone® mediated TEMPO-oxidized cellulose nanomaterials (OTO-CNMs) and their use in controlling the transport properties of polymeric substrates. Synthesis and characterization of cellulosic nanoparticles have resulted in the creation of OTO-CNMs with properties that increase hydrophilicity. With added hydrophilicity, OTO-CNMs possess lower fouling propensity, making them ideal membrane additive for transport limited separations such as hemodialysis.

To utilize the material and unique properties thereof, this …

Charge Transport, Conductivity And Seebeck Coefficient In Pristine And Tcnq Loaded Preferentially Grown Metal Organic Frameworks, Xin Chen, Kai Zhang, Zeinab Mohammed Hassan, Engelbert Redel, Helmut Baumgart

Electrical & Computer Engineering Faculty Publications

This investigation on Metal-Organic Framework (MOF) HUKUST-1 films focuses on comparing the undoped pristine state and with the case of doping by TCNQ infiltration of the MOF pore structure. We have determined the temperature dependent charge transport and p-type conductivity for HKUST-1 films. Furthermore, the electrical conductivity and the current-voltage characteristics have been characterized in detail. Because the most common forms of MOFs, bulk MOF powders, do not lend themselves easily to electrical characterization investigations, here in this study the electrical measurements were performed on dense, compact surface-anchored metal-organic framework (SURMOF) films. These monolithic, well-defined, and (001) preferentially oriented MOF …

Doping Graphene With Substitutional Mn, Pin-Cheng Lin, Renan Villarreal, Simona Achilli, Harsh Bana, Maya N. Nair, Antonio Tejeda, Ken Verguts, Stefan De Gendt, Manuel Auge, Hans Hofsäss, Steven De Feyter, Giovanni Di Santo, Luca Petaccia, Steven Brems, Guido Fratesi, Lino M. C. Pereira

Advanced Science Research Center

We report the incorporation of substitutional Mn atoms in high-quality, epitaxial graphene on Cu(111), using ultralow-energy ion implantation. We characterize in detail the atomic structure of substitutional Mn in a single carbon vacancy and quantify its concentration. In particular, we are able to determine the position of substitutional Mn atoms with respect to the Moiré superstructure (i.e., local graphene-Cu stacking symmetry) and to the carbon sublattice; in the out-of-plane direction, substitutional Mn atoms are found to be slightly displaced toward the Cu surface, that is, effectively underneath the graphene layer. Regarding electronic properties, we show that graphene doped with substitutional …

Investigation Of Surface Charge Using Faraday Bucket Measurements: Analysis On Electrospun Polyvinylidene Fluoride Fiber Mats, Ryan Kantenwein

Williams Honors College, Honors Research Projects

Piezoelectric polymer materials such as polyvinylidene fluoride exhibit beneficial properties for use in personal protective equipment (PPE) against viral contaminants and other foreign microparticles. The electrospinning process of this material allows for surface charge to develop over a controlled surface area. Kynar 761 at 10 wt% demonstrates increased surface charge after withstanding a flow of aerated NaCl particles from a TSI 8130 instrument. Utilizing voltage measurements from a Faraday bucket, 18 wt% Kynar 761 and MG-15 exhibit surface charge when undergoing an electrospinning process; however, Kynar MG-15 displays lower charge values than that of Kynar 761. Several critical factors such …

Development Of Light Actuated Chemical Delivery Platform On A 2-D Array Of Micropore Structure, Hojjat Rostami Azmand, Hojjat Rostami Azmand

Dissertations and Theses

Localized chemical delivery plays an essential role in the fundamental information transfers within biological systems. Thus, the ability to mimic the natural chemical signal modulation would provide significant contributions to understand the functional signaling pathway of biological cells and develop new prosthetic devices for neurological disorders. In this paper, we demonstrate a light-controlled hydrogel platform that can be used for localized chemical delivery in a high spatial resolution. By utilizing the photothermal behavior of graphene-hydrogel composites confined within micron-sized fluidic channels, patterned light illumination creates the parallel and independent actuation of chemical release in a group of fluidic ports. The …

Quality Assurance Of Lightweight Structures Via Phase-Based Motion Estimation, Ikenna E. Ifekaonwu

College of Graduate Studies: Theses & Dissertations

In recent years, lightweight structures have become mature and adopted in various applications. The importance of quality assurance cannot be overemphasized hence extensive research has been conducted to assess the quality of lightweight structures. This study investigates a novel process that exploits motion magnification to investigate the damage characteristics of lightweight mission-critical parts. The goal is to assure the structural integrity of 3D printed structures and composite structures by determining the inherent defects present in the part by exploiting their vibration characteristics. The minuscule vibration of the structure was recorded with the aid of a high-speed digital camera, and the …