Polymer and Organic Materials Commons^™

Friction And Wear Of Polytetrafluoroethylene/Graphene Oxide Composite Thin Films, Justin Kyle Carter

Graduate Theses and Dissertations

Polytetrafluoroethylene (PTFE) is a commonly used solid lubricant due to its low coefficient of friction and chemical inertness. As a polymer, PTFE suffers from high wear and low adhesion to substrates limiting its use as a thin film. Thin PTFE films are ideal candidates for solid lubrication in micro-machines and bearing applications. The main goal of this work is to enhance the durability of thin PTFE films through the addition of few layered graphene oxide (GO) as filler. In order to address adhesion issues, the addition of an adhesive layer of polydopamine (PDA) between stainless steel substrates and thin PTFE …

Crack Growth Behavior Under Creep-Fatigue Conditions Using Compact And Double Edge Notch Tension-Compression Specimens, Santosh B. Narasimha Chary

Graduate Theses and Dissertations

The American Society for Testing and Materials (ASTM) has recently developed a new standard for creep-fatigue crack growth testing, E 2760-10, that supports testing compact specimens, C(T), under load controlled conditions. C(T) specimens are commonly used for fatigue and creep-fatigue crack growth testing under constant-load-amplitude conditions. The use of these specimens is limited to positive load ratios. They are also limited in the amount of crack growth data that can be developed at high stress intensity values due to accumulation of plastic and/or creep strains leading to ratcheting in the specimen. Testing under displacement control can potentially address these shortcomings …

Use Of Polymer Rapid Tools As Functional Injection Mold Tooling, Sean Derrick

Masters Theses

Conventional tool making for injection molded plastics is expensive, time consuming, and generates a great deal of waste. Presently, industry is waiting for what is commonly referred to as Rapid Tooling (RT). The greatest opportunity for RT implementation would be the use of Additively Manufacturing (AM) technology. Specifically, AM techniques which use a high strength polymer resin substrate.

The following research is an initial feasibility study to determine if Polymer Rapid Tools (PRTs) could be used as functional injection mold tooling. The objective of the research was to determine if a PRT could mold a variety of features to a …

Kolsky Bar Experiment For High-Rate Large Deformations Of Polycarbonate, Jason G. Vogeler

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Polycarbonate (PC) is a tough, transparent engineering thermoplastic. Its impact strength and ability undergo large plastic deformations without shatter make PC an ideal protective material for impact-resilient eyewear, aircraft windows and transparent armor. A good understanding of the response of this material to large deformations at high strain rates is critical for its utilization in these applications. To this end, a striker-less Kolsky bar device is employed in this work for the needed material characterization. The apparatus allow impulsive torsion and/or compression loadings with pulse durations sufficiently long for the plastic flow behavior to develop fully. Three new testing techniques …

Kolsky Bar Experiment For High-Rate Large Deformations Of Polycarbonate, Jason Gerald Vogeler

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Polycarbonate (PC) is a tough, transparent engineering thermoplastic. Its impact strength and ability undergo large plastic deformations without shatter make PC an ideal protective material for impact-resilient eyewear, aircraft windows and transparent armor. A good understanding of the response of this material to large deformations at high strain rates is critical for its utilization in these applications. To this end, a striker-less Kolsky bar device is employed in this work for the needed material characterization. The apparatus allow impulsive torsion and/or compression loadings with pulse durations sufficiently long for the plastic flow behavior to develop fully. Three new testing techniques …

Physiological Fluid Specific Agglomeration Patterns Diminish Gold Nanorod Photothermal Characteristics, Kristen K. Comfort, Jared W. Speltz, Bradley M. Stacy, Larry R. Dosser, Saber M. Hussain

Chemical and Materials Engineering Faculty Publications

Investigations into the use of gold nanorods (Au-NRs) for biological applications are growing exponentially due to their distinctive physicochemical properties, which make them advantageous over other nanomaterials. Au-NRs are particularly renowned for their plasmonic characteristics, which generate a robust photothermal response when stimulated with light at a wavelength matching their surface plasmon resonance. Numerous reports have explored this nanophotonic phenomenon for temperature driven therapies; however, to date there is a significant knowledge gap pertaining to the kinetic heating profile of Au-NRs within a controlled physiological setting. In the present study, the impact of environmental composition on Au-NR behavior and degree …

Cellulose Nanocrystals As A Material For Microencapsulation, Lauren C. Kennedy, Congwang Ye, Colton Steiner, Carlos Martinez

The Summer Undergraduate Research Fellowship (SURF) Symposium

Cellulose is an abundant, biodegradable, and inexpensive renewable polymer that is light in weight with high mechanical strength (Habibi, Lucia, Rojas 2010). Full fibers of cellulose have been used in many products such as plastics and textiles for over a century and a half, but recently, modern extraction techniques have made it possible to investigate uses for minuscule cellulose fibers (Habibi, Lucia, Rojas 2010). Through acid hydrolysis, cellulose fibers become rod-like nanostructures with a high aspect ratio that are known as Cellulose Nanocrystals (CNCs) (Habibi, Lucia, Rojas 2010). Since CNCs are biodegradable and derive from a renewable resource, finding ways …

Next Generation Crystal Viewing Tool, Zach Schaffter, Gerhard Klimeck

The Summer Undergraduate Research Fellowship (SURF) Symposium

The science and engineering community is limited when it comes to crystal viewing software tools. Each tool lacks in a different area such as customization of structures or visual output. Crystal Viewer 2.0 was created to have all of these features in one program. This one tool simulates virtually any crystal structure with any possible material. The vtkvis widget offers users advanced visual options not seen in any other crystal viewing software. In addition, the powerful engine behind Crystal Viewer 2.0, nanoelectronic modeling 5 or (NEMO5), performs intensive atomic calculations depending on user input. A graphical user interface, or GUI, …

Efficiently Dispersing Carbon Nanotubes In Polyphenylene Sulfide, Kevin M. Sommer, R. Byron Pipes

The Summer Undergraduate Research Fellowship (SURF) Symposium

Thermal plastics are replacing conventional metals in the aerospace, sporting, electronics, and other industries. Thermal plastics are able to withstand relatively high temperatures, have good fatigue properties, and are lighter than metals. Unfortunately, they are not very electrically conductive. However, adding carbon nanotubes to thermal plastics such as polyphenylene sulfide (PPS) can drastically increase the plastic's conductivity at a low weight percent of nanotubes called the percolation threshold. The percolation threshold is the point where adding a little more carbon nanotubes brings together the network of nanotubes and greatly increases the conductivity. We need to learn how to increase the …

Testing Self Healing Properties In Polymers, Hamsini Gopalakrishna, John Blendell

The Summer Undergraduate Research Fellowship (SURF) Symposium

Mussels and barnacles have the ability to stick to underwater surfaces with the help of a cross-linked protein structure. Reduction in the plastic consumption can be achieved by using toughened polymers. Synthesized cross-linking polymers can be used for underwater adhesion by mimicking the protein structure used by mussels and barnacles. One such polymer is poly(3,4-dihydroxystyrene-co-styrene) having enhanced toughness. Traditionally, blister tests measure the adhesion between a substrate to a surface but this was modified to serve as the driving force to drive crack propagation in controlled flaws. The modified blister tests were carried out on polystyrene (PS) samples. Once the …

Interfacial Rheological Mechanics Of A Non-Ionic, Tri-Block Copolymer At Water/Hexadecane Interface, Jerome J. Nash, Kendra Erk

The Summer Undergraduate Research Fellowship (SURF) Symposium

Growing interest on the stability of foams and emulsions has lead to concentrated research of interfacial rheology. The response of an interfacial layer to mechanical deformation in size and shape is dependent on its composition. [Miller 2010] This research analysis focused on the adsorption and rheological mechanics of the non-ionic, tri-block copolymer, Pluronic 17R4 at the water/hexadecane interface. The adsorption and viscoelastic properties of the interface were measured via methods of pendant drop tensiometry and dynamic oscillation with drop shape analysis software. Interfacial tension measurements were taken to study the surface pressures of Pluronic 17R4 solutions with concentrations ranging from …

The Biological Impact Of Concurrent Exposure To Metallic Nanoparticles And A Static Magnetic Field, Kristen K. Comfort, Elizabeth I. Maurer, Saber M. Hussain

Chemical and Materials Engineering Faculty Publications

The rapid advancement of technology has led to an exponential increase of both nanomaterial and magnetic field utilization in applications spanning a variety of sectors. While extensive work has focused on the impact of these two variables on biological systems independently, the existence of any synergistic effects following concurrent exposure has yet to be investigated. This study sought to ascertain the induced alterations to the stress and proliferation responses of the human adult low calcium, high temperature keratinocyte (HaCaT) cell line by the application of a static magnetic field (approximately 0.5 or 30 mT) in conjunction with either gold or …

Low Volume Dispensing With High Speed Dispensers, Sunny Agarwal

Graduate Dissertations and Theses

With the high pace of innovation in the semiconductor manufacturing industry, there has been an increasing demand for more energy efficient and environmental friendly products. This research relates to a complex process of fluid dispensing at low volumes on a printed circuit board. Currently, a more refined non-contact dispensing terminology named “Streaming” is widely used to stream out material at low volumes for various applications. The key solution is to frame a dispensing method that lends itself most closely to the requirements of a specific production process.

This study represents a detailed approach of dispensing low volumes of materials in …

Improved Deinkability Of Lep (Liquid Electrophotography) Digital Prints, Zheng Wei

Masters Theses

Digital printing plays a very important role in the life of modern society. With the development of digital printing technologies, and the increasing market share of digital printing, the amount of digital prints in waste paper is rapidly increasing. Under “green” manufacturing and environmental sustainability, deinking of digital print inks is an urgent problem that needs to be solved. Indigo is a typical series of HP (Hewlett-Packard) digital presses that use a liquid ink named ElectroInk (Liquid Electrophotography or LEP). The particle size of HP ElectroInk is very small, 1-2 microns, which is smaller than dry toners. But, during flotation, …

Pan Nanofibers And Nanofiber Reinforced Composites, Cheng Ren

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Nanomaterials play an important role in the development of nanotechnology. They possess unique mechanical, physical, and chemical properties coupled with small size and ultrahigh surface area that can provide critical advantages for applications. Continuous nanofibers attract special interest due to their dual nano-macro nature and ability to bridge scales. Nanofibers are being considered for a broad range of applications spanning advanced filters, separation membranes, ultrasensitive sensors, micro/nano actuators, nanoprobes, tissue engineering scaffolds, protective and smart closing, and multifunctional composites. Most of these applications require certain mechanical properties and robustness. However, the literature on the mechanical behavior of nanofibers and their …

Complementarities Of Probabilistic And Evidence Approaches: An Uncertainty Assessment For Selection Of Composite Material, Stella B. Bondi, Resit Unal, Patrick T. Hester, Trina M. Chytka

Engineering Technology Faculty Publications

A complimentary probabilistic and evidence theory approach is utilized to enhance uncertainty assessments in the area of critical safety characteristics for conceptual design. This research provides additional exploration into the failure modes necessary to utilize Fiber Reinforced Polymer (FRP) and various composites to their fullest potential and to minimize uncertainty by comparing probability and evidence theories. This combined approach has been applied to a selection of composite material that could provide uncertainty assessment design for a space transportation system. Uncertainty estimates presented are bounded by belief and plausibility functions. The results may provide additional information to the decision makers in …

Improving The Efficiency Of P3ht:Icba Organic Solar Cells By Modifying The Photoactive Solution Preparation Step, Matthew Blaine Samson

Electrical & Computer Engineering Theses & Dissertations

Organic solar cells (OSCs) are a promising alternative to conventional silicon solar cells. These organic devices offer the promise of facile low cost large scale solution based processing on lightweight, flexible, plastic substrates. At the present state of the technology, however, OSCs exhibit relatively low power conversion efficiencies. To improve these efficiencies, new materials are constantly being developed.

One such material is the fullerene indene-C₆₀ bisadduct (ICBA). When implemented in a poly(3-hexylthiophene-2, 5-diyl) (P3HT) : ICBA bulk heterojunction solar cell, these devices exhibit open circuit voltages exceeding 0.8 V, a value much higher than the devices made implementing phenyl-C …

The Equi-Biaxial Fatigue Characteristics Of Epdm Under True (Cauchy) Stress Control Conditions, Mark Johnson

Conference Papers

Strain amplitude control is most often employed when carrying out fatigue testing of rubber components. Often the design engineer requires fatigue test data that is based on load amplitude control. This is analogous to engineering or nominal stress amplitude control. This usually makes it easy to maintain the load within the specified test limits during extended testing. Values of true stress and strain can be obtained from this approach, but the magnitudes of the maximum true stresses in these tests increase with accumulated cycles, whereas the equivalent maximum engineering stress values remain constant. This is easily demonstrated in the uniaxial …

Materials Education And Research In Art And Design: A New Role For Libraries (Survey Stats), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Program Sheet), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Program Booklet), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Website), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Collection Creation And Administration: A New Role For Libraries (White Paper), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

The Problem/Opportunity: To define, identify, and guide design-based materials collections in academic settings and foster community among those with existing collections and/or those considering creating and supporting one.

Contents and topics:

1. What is a materials collection?
2. Why have a materials collection?
3. Acquisition strategies
4. Organizational approaches
5. Programming possibilities
6. Symposium summary
7. Resources

Lunalight - Bringing Light To The Expanding World, Gabriela M. Igel, Daniel J. Patrick, Kimberley M. Smith

Materials Engineering

The LunaLight, a solar rechargeable light and cell phone charger, addresses the lack of access to electricity faced by 1.4 billion of the world’s population (International Finance Corporation). The LunaTech team has developed a product that is bright, simple, compact, versatile and competitive with existing products. Through a partnership with the non-profit organization One Million Lights, LunaTech has improved a previous team’s design to address user feedback, concerns of durability, and manufacturability.

The LunaLight design includes a 5 component plastic housing held together by 4 screws, a surface mounted PCB, a lithium-ion (Li-Ion) battery, one high-brightness LED, a solar panel, …

The Fabrication & Characterization Of An Electrokinetic Microfluidic Pump From Su-8, A Negative Epoxy-Based Photoresist, Nash Anderson

Master's Theses

Microfluidics refers to manipulation, precise control, and behavior of fluids at the micro and nanoliter scales. It has entered the realm of science as a way to precisely measure or mix small amounts of fluid to perform highly controlled reactions. Glass and polydimethylsiloxane (PDMS) are common materials used to create microfluidic devices; however, glass is difficult to process and PDMS is relatively hydrophobic. In this study, SU-8, an epoxy based (negative) photoresist was used to create various electrokinetic microfluidic chips. SU-8 is commonly used in microelectromechanical design. Spin coating of various SU-8 formulations allows for 1 μm to 100 μm …

Evaluation Of Corrosion Properties Of Proprietary Metal Alloy Stents For In-Vivo Use, Michael David Bremner

Materials Engineering

To assess corrosion rates of metal alloy bio-absorbable stents an experimental set-up was designed to mimic the coronary artery environment. The artery was modeled using 4mm diameter Tecoflex tubing and the metal alloy stents were inserted into the tubing using a catheter. As is the case in cardiac surgery, the catheter with the stent and a microballoon were maneuvered to the desired position. The microballoon was then slowly inflated to expand the stent and compress it against the tubing walls. The catheter and microballoon were then withdrawn. A circulating pump system was set up to cycle fetal bovine serum (FBS) …

Preparation Of A Polylactic Acid With Hydroxyapatite Reinforcement Composite, Odessa N. Quezon

Materials Engineering

Biodegradable polymers are a prime material choice for temporary biomedical devices due to its ability to degrade into non-toxic products for their use in vivo. However, polylactic acid (PLA) by itself lacks the sufficient strength and stiffness to permit their use as its properties begin to decrease as the polymer degrades. To improve the polymer’s mechanical properties, hydroxyapatite (HA) will be added to the PLA solution to act as reinforcement. The chemical property, glass transition temperature of a polymer, also plays a key role in the mechanical properties of the polymer. PLA’s glass temperature is 130⁰F. A polymer that …

Strength Testing And Material Characterization Of Cactus Spines, Mary Cooper, Jeff Goldstein, Thomas Tarlton

Materials Engineering

Twelve different species of cactus spines from 6 different genera were collected from living specimens and maintained in a dry storage environment. Spines from each species underwent 3-point bend testing, XRD testing, and SEM imaging. XRD analysis was used to verify the presence of cellulose whisker like nanocrystals and to calculate the percent crystallinity of each spine. SEM images were captured of fracture surfaces at viewing angles of 90° and 45° relative to the fracture surface, with magnifications ranging between 150x and 4,000x. A total of six spines from each species were tested in three point bending using a high-resolution …

Design And Construction Of A Simulated Evaporative Heat Exchanger For Testing The Mitigation Effects Of Pipe Coatings On Mineral Scale Deposition, Taylor J. Anderson

Materials Engineering

The thermal efficiency of evaporative heat exchangers is diminishing due to mineral scale buildup on heat exchanger surfaces. A simulated evaporative heat exchanger was designed and constructed for testing the mitigation effects of polymer coatings on mineral scale deposition rates. The heat exchanger was designed to cool hot mud at 200°F using a cooling water supply with a calcium concentration of 1000 ppm. The system was constructed using 1.5-inch diameter polypropylene piping, a DIG Corporation drip irrigation system, a TotalPond 530 GPH pond pump, an Omega CSI32K miniature benchtop controller, Omega FWH321-020 high temperature heater tape, and fifteen copper pipe …

Analyzing The Acoustical Properties Of Alternative Materials In Guitar Soundboards To Reduce Deforestation, Chris Dunn

Materials Engineering

To mitigate the effects of deforestation, man-made alternative materials were analyzed and tested for potential use in the soundboards of acoustic guitars. The materials evaluated included 0.06 in. foamed polycarbonate, 0.12 in. single-ply honeycomb fiberglass, and 0.04 in. epoxy fiberglass. The properties of Sitka spruce, the most common tonewood, were used as a benchmark. The Young’s modulus to density ratio found in Sitka spruce is relatively high, making its properties ideal for soundboard applications. Both Young’s modulus and density were necessary to calculate the acoustic constant of each material that was tested. The samples were subject to the impact of …