Polymer and Organic Materials Commons^™

Effect Of The Stacking Sequence And Number Of Ply Orientation In A Quasi-Isotropic Laminated Plate On In-Plane Shear Modulus And Failure Modes, Ann Larson

Master's Theses

Maximizing the shear modulus and strength, as well as predicting failure mode and location, when designing a stacking sequence of quasi-isotropic carbon fiber laminated plates is essential to predict stability, resistance to deformation, and overall stiffness of the structure. This research investigates the effect of the stacking sequence of quasi-isotropic laminated composite plate materials in accordance with ASTM D5379: Standard Test Method for Shear Properties of Composite Materials by the V-Notched Beam Method.

In this research, experimental testing and Finite Element Analysis (FEA) were first used on aluminum to validate the simulation process before applying it to composite materials. The …

Thermally Induced Color Changes In Iron Oxide Pigments Used In Architectural Coatings, Han Diep

Master's Theses

The 2025 Palisades Fire was one of the most destructive wildfires in the history of Los Angeles, destroying thousands of structures and severely impacting the communities after. This widespread destruction demonstrated an urgent need for more effective wildfire prevention strategies. Architectural coatings do not only provide aesthetics and protection against environmental conditions but can also function as a thermal indicator when a fire breaks out. This study examines the thermally induced color transformation of iron oxide pigments, commonly used in earthtone paint, to provide information relevant to CAL FIRE for improved analysis of wildland-urban interface (WUI) fire behavior and mitigation …

Myceli-Yum: Elucidating Structure-Property Relationships For Polymer Degradation By Mycelial Digestion, Jordan Scott Ford

Master's Theses

Since the industrial entrance of polymer plastic materials, plastic has become ubiquitous in both everyday use and waste. Due to inefficiencies and knowledge gaps, current recycling methods are not able to account for the high scale of plastic waste, resulting in the bulk of this waste being landfilled, mishandled, and deposited in the environment. Mycelium, the microorganism responsible for fruiting mushroom bodies and mold growth, holds potential to reduce plastic waste and can potentially be utilized as a method of industrial recycling. Following a drug-design approach, the active site of mycelial enzymes responsible for natural biopolymer degradation have been assessed …

Multimodal Self-Folding Of Shape Memory Polymer Using Laser Induced Graphene, Liam Harrison Drew

Master's Theses

Shape memory polymers (SMPs) can undergo programmed shape transformations when heated above their glass transition temperature (T_g), enabling actuation through stimuli such as infrared (IR) radiation and Joule heating. These materials are promising for deployable systems and soft robotics due to their lightweight structure and elimination of traditional mechanical components. While IR-based actuation is simple and low-cost, it lacks precision in uncontrolled environments. Joule heating offers improved control but is often limited by conductive ink properties such as thickness, stiffness, or poor adhesion. This work introduces a novel method for multimodal SMP actuation using laser-induced graphene (LIG) transferred …

Low Earth Orbit Drag Sail Degradation Due To Atomic Oxygen And Ultraviolet Radiation, Hannah Rost

Master's Theses

As the orbital debris population increases, so does the risk of collisions with operational spacecraft. In response, the Federal Communications Commission has shortened the deorbit requirement from 25 years to five years. While natural atmospheric decay was sufficient under the previous guideline, many objects with low area to mass ratios can no longer passively comply. Smaller, non-propellant-carrying space objects such as CubeSats lack the ability to maneuver and must rely on alternative deorbit methods. One proposed solution is to deploy a drag sail at end of life to increase atmospheric drag and accelerate orbital decay. However, exposure to atomic oxygen …

Investigation Into Silicone-Silicate Conversion Due To Atomic Oxygen In The Low Earth Orbit Environment, Justin T. Self

Master's Theses

Silicones have been widely used over the years in spacecraft for a variety of functions, but atomic oxygen (AO) exposure in Low Earth Orbit causes a silicate (SiO₂) surface layer to rapidly develop on the silicone which results in a permanent change in its thermal and optical properties. Although this silicone to silicate conversion is known to occur, statistical predictions of layer formation as a function of time on orbit are not found in literature. This thesis utilized optical and scanning electron microscopy, Fourier-Transform Infrared Spectroscopy, diffuse reflectance spectroscopy, and nonlinear regression statistical techniques after RF plasma asher …

Degradation Characterization Of Nopal-Based Biopolymer Made From Opuntia Sp. Juice, Beeswax, Animal Protein, And Polyvinyl Alcohol, Logan Williams, Mary Elizabeth Holland, Spencer Williams

Materials Engineering

Since the introduction of polymers in the 1960s, there has been an exponential increase in use. Driven by rapidly growing demand, the volume of polymers in the production, application, and end-of-life stages has surged. The widespread use of these materials has led to escalating environmental pollution, which disrupts ecosystems, and contributes to global ecological degradation. While advancements in recycling technologies and infrastructure have shown promise, they have not maintained pace with polymer production and disposal. This imbalance warrants research into sustainable alternatives. Environmentally benign polymers derived from renewable sources and exhibiting minimal ecological impact at the end of their life …

Chemical Recycling Of Pet Plastic Waste, Charlie Parker, Benjamin Puga, Jake Verschoor

Materials Engineering

The growing accumulation of plastic waste, specifically polyethylene terephthalate (PET), has driven the need for more efficient and scalable chemical recycling methods. This study investigated the methanolysis of PET using zinc oxide (ZnO) nanoparticles as a catalyst and tetrabutylammonium chloride (NBu₄Cl) as an ionic liquid, aiming to reduce methanol consumption while achieving high PET conversion efficiency. ZnO nanoparticles were synthesized via wet chemistry and characterized using Dynamic Light Scattering (DLS), which showed an average particle size of 13.5 nm with a polydispersity index of 0.1556, indicating a moderately-high monodisperse distribution of particles sufficient for reactions. The main conversion product, dimethyl …

Development Of Ex-Situ Accelerated Chemical Stress Test Protocol For Common Anionic Exchange Membrane Chemistries, Michael D. Friend, Michael D. Friend

Master's Theses

The development of sustainably produced hydrogen fuel (“green hydrogen”) is key for the transition to clean energy sources. Green hydrogen is produced via water electrolysis. As with many clean energy sources, one of the major barriers for scaling water electrolysis is cost. A newer category of water electrolysis is Anionic Exchange Membrane (AEM) water electrolysis. AEM electrolysis systems have the potential to cost less as they do not require the expensive precious metal catalysts the current high preforming Proton Exchange Membrane water electrolysis technologies do. However, AEM lifetimes must be long enough to be cost competitive and AEM chemical durability …

Solubility Characterization Of Organic Molecules For Aqueous Organic Redox Flow Batteries, Anthony W. Ferrell, Harkeerith K. Vij, Seamus D. Jones

College of Engineering Summer Undergraduate Research Program

The major obstacle to renewable energy sources is a lack of long-term energy storage capabilities. Energy produced during the day dissipates, leaving insufficient electricity for at night. The goal of the project is to design an Aqueous Organic Redox Flow Battery (AORFB) to act as long-term energy storage. Work has been done using machine learning to identify suitable compounds for the batteries. In this work there was no indication as to the aqueous solubility of the molecules; this controls the device’s energy storage capabilities. We used a machine learning model to determine the aqueous solubility of slightly more than 3000 …

Investigation Of Temperature, Solution Strength, And Applied Stress Effects On Cation Exchange Processes In Different Geosynthetic Clay Liner Products, Kendra Fuller

Master's Theses

An extensive laboratory test program was conducted to analyze and compare the cation exchange processes in three different varieties of sodium bentonite (Na-B) geosynthetic clay liners (GCLs) over increased conditioning durations up to 32 days and investigate the effects of temperature, solution strength, and applied stress. The goal of this test program was to establish whether the variables of temperature, solution strength, and applied stress improved or degraded the engineering properties of GCLs in laboratory testing and municipal solid waste (MSW) landfill applications. The GCLs were conditioned in liquids of increasing ionic strength, using deionized water and 2, 50, and …

Predicting Rheology Of Uv-Curable Nanoparticle Ink Components And Compositions For Inkjet Additive Manufacturing, Cameron D. Lutz

Master's Theses

Inkjet additive manufacturing is the next step toward ubiquitous manufacturing by enabling multi-material printing that can exhibit various mechanical, electronic, and thermal properties. These characteristics are realized in the careful formulation of the inks and their functional materials, but there are many constraints that need to be satisfied to allow optimal jetting performance and build quality when used in an inkjet 3-D printer. Previous research has addressed the desirable rheology characteristics to enable stable drop formation and how the metallic nanoparticles affect the viscosity of inks. The contending goals of increasing nanoparticle-loading to improve material deposition rates while trying to …

Fabrication Of Alumina Membranes From Uv Resin– Alumina Particle Slurries, Dominique Henry Porcincula

Master's Theses

Ceramics membranes are made in a wide variety of different techniques using a wide variety of different materials. However, many of the common techniques utilize a slurry of ceramic particles, additives, and either organic solvent or water that is shaped into a membrane, left to dry, and then sintered together. Drying is a time consuming process, often requiring several hours for the liquid medium to evaporate. Defect formation caused by development of partial pressures across the drying membrane, including cracks and warpage, also typically occurs during the drying process. To address this, slurries of ceramic particles made with a low …

Surface Characterization Of Low-Density Polyethylene Mulch, Risha Shah

Materials Engineering

Plastic pollution in aquatic systems has traditionally been highlighted in past and current research due to the increase in plastic production every year. Unfortunately, quantitative and qualitative data regarding plastic pollution on land systems such as agricultural mulch is limited. Agricultural mulch breaks down into macroplastics and then degrades into microplastics. The microplastics investigated in this study are all secondary microplastics: microplastics that form due to weathering of larger fragments of plastic. Weathering can occur due to a variety of factors; however, UV radiation and mechanical weathering have been the factors of focus on most current research in microplastic formulation. …

Interlaminar Tensile Properties Of Unidirectional And Woven Carbon Fiber Reinforced Toughened Epoxy Laminates, Eric Timothy Casey, Sean Mckalip Thompson

Materials Engineering

This project aims to develop a dataset on interlaminar tensile strength comparing unidirectional and woven thermoset matrix carbon fiber composites keeping ply count, matrix material, and fiber diameter constant. The interlaminar tensile strength is an important property relating to the delamination failure mode. Interlaminar tensile strength is determined using the ASTM D6415 testing standard. This test is a modified four-point bend test using a 90° curved beam test specimen. Laminates were produced by laying up pre-impregnated carbon fiber sheets onto a curved beam tooling. The unidirectional laminate was produced with 20 plies in a [0,0,90,0,0]₄ layup pattern. The woven …

Effect Of Environmental And Ultraviolet Degradation On The Albedo Of Polyethylene Sheet Materials For Improved Energy Harvesting By Bifacial Photovoltaic Power Plants, William A. Jang, Roxy H. Jackson-Gain

Materials Engineering

Solar energy farms typically utilize monofacial photovoltaic (mPV) cells in their arrays to capture direct sunlight to produce renewable energy. However, the efficiency of these farms can be increased by 2 – 6% through the implementation of bifacial photovoltaic cells (bPV). These bPV cells function by capturing incident ultraviolet (UV) light energy that is reflected off the surface to increase its overall energy production. The amount of UV energy that is reflected is dependent on the albedo value of surface, which is a measure of energy reflectance. In this study, samples of unreinforced polyethylene (PE), scrim-reinforced polyethylene (SR-PE), and woven …

Covalent Adaptable Networks For Wood Coatings, Jachin Boaz Clarke

Materials Engineering

Wood swells and shrinks causing problems with seasonal humidity. Applying thick coatings of reactive finishes based on cross-linked polyurethane, epoxy, or polyesters can slow moisture-vapor exchange. However, the use of thick coatings leads to cracking and crazing sooner than thin finishes. This research proposes the addition of 3.3 mol % triazabicyclodecene, a conventionally used covalent adaptable network catalyst, in a commercially available polyester-based wood coating. The self-healing of the wood coating is tested using DMA stress relaxation and compression molding. The result from DMA renders inconclusive and compression molding indicates the novel wood coating oxidizes at elevated temperatures. The wood …

Fabrication Of Thin-Film Composite, Reverse-Osmosis Membranes With Polyethylenimine Modifications For Enhancing Membrane Fouling Resistance, Stephanie N. Hamilton

Master's Theses

Increasing water reuse opportunities for communities has become increasingly important as access to clean water is becoming more scarce. Reverse Osmosis (RO) is an advanced treatment technology used in water recycling wastewater for potable reuse applications. RO is a promising technology; however, the membranes have limitations including their high energy demand and their susceptibility to membrane fouling. The main objective of this study was to develop a reproducible method for the fabrication of RO membranes with enhanced flux and reduced susceptibility to fouling. Literature contains numerous publications on fabrication of thin film composite (TFC) RO membranes with high performance. However, …

Evaluating The Effects Of Granulated Rubber And Glass Fibers In Polymer Concrete As A Structural Material For Wafer Grinding Machines, Kevin Gabriel Kuehn, Philip Randall Streeter

Materials Engineering

Polymer concrete is a composite material used to replace cast iron and steel in wafer grinding machines for vibration damping. During the grinding and lapping processes of manufacturing silicon wafers, excessive vibrations may cause subsurface damage which requires additional polishing and reduces yield. Nine compositions containing various levels of granulated rubber and glass fibers were manufactured. CRM WRF-10 granulated rubber was examined at 0%, 5%, and 10% and Corning Cem-Fil glass fibers were added at 0%, 0.5%, and 1% by weight. Smooth-On EpoxAcast 690 epoxy resin was held constant at 16% for each composition. Crushed granite aggregate from Martin Marietta, …

Stabilization Of Palm Wood Using Water-Based Impregnation, David A. Barnes

Materials Engineering

Impregnation is a technique for stabilizing wood that involves saturating the material in a liquid and allowing it to cure before use. Stabilization methods such as this are employed for a variety of reasons; chiefly, the low dimensional stability of wood and palm means that they are subject to several failure modes that arise from changing environmental conditions, such as cracking, warping, and bending. Samples of Borassus flabellifer, black palm, provided by DuraPalm were impregnated with solvent-based and water-based stabilizers, and untreated wood samples used as a control group. Kop-Coat WoodYouth® Plus was used as a solvent-based stabilizer, and impregnation …

Effects Of Release Materials And Temperature Ramp Rates On The Surface Finish Of Carbon-Fiber Composite Components, Sudeep Louis, Thucmy Dang, Ethan Schlocker

Materials Engineering

Toray Advanced Composites is interested in improving their carbon fiber reinforced polymers (CFRP) manufacturing process by enhancing their control on the amount of surface roughness for varied customer preference. Surface roughness of CFRP is important in post-production processes including coating, priming, and painting. This project seeks to determine the effects of three release materials and two temperature ramp rates on the surface finish of CFRP. The release materials used were Tooltech, FEP, and Frekote 770-NC. The two initial temperature ramp rates were 1°F/min and 2°F/min. Surface roughness was measured using a profilometer and analyzed using Ra values. Ra is an …

Analysis Of Novel Corrosion Resistant Maraging Steels For Use In Additive Manufacturing, Bradley Michael Samuel, James Knowlton Smith

Materials Engineering

Stainless maraging steel has been proven to be an industry standard material for plastic injection molds. Its high hardness and corrosion resistance extend the lifetime of the tool. This alloy system is also well-suited to additive manufacturing, which can be utilized to form internal cooling channels, further increasing tool life. Using Rapid Alloy Development (RAD) Oerilkon METCO is developing a new composition of stainless maraging tool steel that has high hardness/strength, is corrosion resistant, and has additive-capable melting and solidification properties. This study tests the hardness and corrosion resistance of the new RAD alloys against the current market competitor Corrax …

In Situ Marine Biodegradation Of Poly(Lactic) Acid And Thermoplastic Starch Blends, Brittany Denicholas

Materials Engineering

Marine life has been suffering from macro- and microplastics since the inception of petroleum-based plastic. Bio-based biodegradable polymers such as PLA and TPS can help mitigate the damage done by petroleum plastics. Blending PLA and TPS can reduce the cost while preventing a significant effect on the material properties. PLA/TPS blend compositions such as 90/10, 80/20, 70/30 could be candidates for a solution. The PLA/TPS blends have been submerged in a marine environment at the Cal Poly Pier in Avila Beach for 8 weeks. Three sample sets containing three of each blend composition were collected every week and tested in …

Citric Or Acetic Acid Effects On The Crosslinking Of Pvoh, Samuel Carr, Erika Szaldobagyi

Materials Engineering

Transportation and shipping processes are the most dangerous times for food due to harsh handling and frequent temperature changes. Plain corrugated boxes cannot withstand the damp environment caused by melting ice that is used to keep foods cold and fresh. To minimize damage, a protective polymer film coating can be applied. These coatings can be unsafe when used with food and will lead to excess waste by limiting the recyclability of the boxes. The purpose of this project was to produce nontoxic crosslinked PVOH films to determine suitability for a cost effective, biodegradable, and repulpable corrugated box coating. Polyvinyl alcohol …

Determining The Efficacy Of A Silica And Bacterial Cellulose Composite Model System, Hannah Martin, Daisy Kamp

Materials Engineering

Bacterial cellulose (BC) is a sustainable alternative to petroleum-based polymer films for synthetic leather applications. Synthesized by a symbiotic culture of bacteria and yeast, BC is a three-dimensional structure composed of cellulose microfibrils. However, pure BC lacks certain desirable properties such as high tensile strength. Previous studies have shown that loading BC with nanoparticles to form nanocomposites has improved BC’s mechanical properties. However, this was not studied as a function of particle size. This study focuses on using silica/BC nanocomposites to model the impact that particle size and silica soaking concentrations have on the uptake efficiency of these particles into …

Soil Degradation Of A Plastic Blend Of Opuntia Ficusindica Juice, Animal Protein And Beeswax, Isabel A. Gamez, Daniel R. Kava

Materials Engineering

Since the introduction of single use plastics in the early 1900s, their usage has increased exponentially. Unfortunately, due to this exponential increase there are negative environmental implications of their production, which requires further consideration. Currently, there are various waste disposal practices for SUPs, including landfilling, incineration, and recycling. Recent data revealed that only 14 % of plastic waste was recycled, with 40% of plastic waste being landfilled, while the rest of the plastic waste was incinerated or released to the environment at 14 % and 32 %, respectively. A potential solution to the plastic waste issue is developing a polymer …

Optimization Of A Novel Nipam-Based Thermoresponsive Copolymer For Intramuscular Injection As A Myoblast Delivery Vehicle To Combat Peripheral Artery Occlusive Disease, Quentin R. Klueter

Master's Theses

There is a need for a minimally invasive delivery method to enable cell therapies to combat peripheral artery occlusive disease (PAOD) in end stage patients. Myoblasts show promise as a cell mediated therapy but warrant an improved delivery method to increase cell retention in the region of interest because of their adherent nature, relative to previously used BM-MNC’s that are non-adherent. Contemporary issues with achieving successful cell therapies of vasculature can be mainly characterized by the lack of clinical translation from promising animal studies and absence of cell delivery scaffolding. Naturally, polymers have been widely experimented with as grafts to …

Automated Mini-Tubular Ceramic Production, Hunter Brooks, Daniel Freeman, Leo Taranta-Slack

Mechanical Engineering

Researchers at Lawrence Livermore National Laboratory need a way to increase the rate of manufacturing of mini-tubular ceramics to be used in testing particulate air filters. This document outlines our process from researching and writing an initial scope of work all the way to fabricating and testing a final prototype. This journey takes us through the background research, ideation process and selection of a final design. We also detail the desired engineering specifications and our concept selection process. We dedicate a significant portion of this report to discussion of our final design. We delve into how it was manufactured as …

Analysis Of The Use Of Waste Material In 3d Printing, Alexander Laurence

Materials Engineering

Globally, only 9% of plastic by mass is recycled. Allowing consumers to directly convert polyethylene terephthalate (PET) waste into 3D filament can increase the recycling rate by reducing contamination and costs from traditional large-scale recycling methods. This was tested by heating strips of PET to various temperatures within its glass transition region and pressing a roller with a 1.75 mm indentation against it to observe strip deformation. PET was also placed in a hemispherical well with a 1.75 mm diameter hole at the bottom and heated above its melting temperature to determine the mass of PET required to extrude 3D …

Void And Density Analysis Of Cyanate Ester Composites, Cameron B. Atwood

Materials Engineering

In large scale composite manufacturing, voids and their frequency within prepreg materials play an important role in predicting the mechanical properties of a final composite laminate. The industry standard process for determining voids in composite materials is through resin digestion and resin ignition via ASTM D3171. One limitation to this standard is its ability to frequently produce negative void volume values in quality control testing, due to the calculation sensitivity of input resin and fiber densities. For this reason, Toray Advanced Composites wanted to investigate the process steps of ASTM D3171 to determine if discrepancies in resin density data may …