Polymer and Organic Materials Commons^™

Tuning Ion Mobility And Molecular Confinement In High-Performance Polymer Electrolytes For Energy Storage, Ezzeldien Yousef Muhammed Yousef

Theses and Dissertations

This research addresses the critical energy density limitations of aqueous supercapacitors, which are traditionally constrained by the narrow electrochemical stability window (ESW) of water 1.23 V. By employing two distinct molecular engineering strategies, this study developed high-performance electrolyte systems that significantly extend voltage stability and thermal resilience.

The first system, CsBr@PAM/HA, utilizes a polyacrylamide and hyaluronic acid hydrogel matrix. This system exploits the chaotropic nature of Cs⁺ ions to disrupt the aqueous hydrogen-bonding network, enhancing ionic conductivity to 104 mS cm^-1. Through systematic salt screening, CsBr was identified as the optimal electrolyte, enabling a stable 2.0 V …

Thermally Induced Color Changes In Iron Oxide Pigments Used In Architectural Coatings, Han Diep

Master's Theses

The 2025 Palisades Fire was one of the most destructive wildfires in the history of Los Angeles, destroying thousands of structures and severely impacting the communities after. This widespread destruction demonstrated an urgent need for more effective wildfire prevention strategies. Architectural coatings do not only provide aesthetics and protection against environmental conditions but can also function as a thermal indicator when a fire breaks out. This study examines the thermally induced color transformation of iron oxide pigments, commonly used in earthtone paint, to provide information relevant to CAL FIRE for improved analysis of wildland-urban interface (WUI) fire behavior and mitigation …

Adsorption Of Pfas On Bridged Functionalized Organosilica Materials, Elisha Lawerh Kabutey

Electronic Theses and Dissertations

PFAS are hazardous contaminants that have a devastating impact on human health and the environment. Their hazardous nature has led to the development of various adsorption methods for removing these contaminants from water sources. In this study, functionalized organosilica materials were synthesized from bis[3-(trimethoxysilyl)propyl] amine using the sol-gel method. The surface amino groups of the organosilica were converted into amine hydrochloride groups. Their adsorption properties were evaluated using salts of perfluorooctanoic acid, perfluorooctanesulfonic acid, and perfluorobutanesulfonic acid. Results showed excellent adsorption capacity of the materials. Adsorption of PFAS leads to particle agglomeration and flotation of the spent material. A column …

Engineering Silicone Magnetic Fluids For Localized Radiation Attenuation During Ocular Melanoma Brachytherapy, Zachary L. Caprow

All Dissertations

Ocular melanoma is commonly treated using plaque brachytherapy; however, radiation-induced damage to healthy ocular tissues frequently results in partial or complete vision loss. This work investigates the development of an injectable, magnetically responsive silicone magnetic fluid designed to localize adjacent to the tumor and attenuate low-energy gamma radiation during treatment.

The material system consists of iron oxide nanoparticles surface-functionalized with a siloxane polymer, in which the nanoparticles provide magnetic responsiveness and radiation attenuation, while the polymer coating ensures colloidal stability, injectability, and biocompatibility. A one-pot synthetic approach was developed wherein a functionalized siloxane polymer containing iron-affinitive groups was reacted with …

An Overview Of Biomass-Derived Graphene Oxide And Its Characteristics For Future Sustainable Applications, Afif Wardana, Ahmad Nabil Shahab, Donanta Dhaneswara, Nofrijon Sofyan

Journal of Materials Exploration and Findings

The production of graphene oxide (GO) from biomass presents considerable promise as a sustainable alternative substitute for traditional semiconductors. Biomass waste, abundant and often underutilized worldwide, is distinguished by its high carbon content and regenerative characteristics, rendering it an optimal resource for sustainable material production. By heating its biopolymers, lignocellulosic biomass can be used as a new material to make graphene, which forms three-dimensional turbostratic crystallites. These crystallites, composed of partially defective aromatic carbon sheets with graphite-like characteristics, make it easier to create GO with specialized functions for cutting-edge applications. Its capability underscores the revolutionary potential of biomass waste in …

Myceli-Yum: Elucidating Structure-Property Relationships For Polymer Degradation By Mycelial Digestion, Jordan Scott Ford

Master's Theses

Since the industrial entrance of polymer plastic materials, plastic has become ubiquitous in both everyday use and waste. Due to inefficiencies and knowledge gaps, current recycling methods are not able to account for the high scale of plastic waste, resulting in the bulk of this waste being landfilled, mishandled, and deposited in the environment. Mycelium, the microorganism responsible for fruiting mushroom bodies and mold growth, holds potential to reduce plastic waste and can potentially be utilized as a method of industrial recycling. Following a drug-design approach, the active site of mycelial enzymes responsible for natural biopolymer degradation have been assessed …

Mechanistic Investigation Of Ring-Opening Polymerization Of Polycaprolactone Using Tin(Ii) Catalysts: Ligand Effects And Biomedical Applications, Eva-Larue M. Barber

Honors Scholar Theses

This research explores the mechanistic aspects of ring-opening polymerization (ROP) of ε-caprolactone (CL) to produce polycaprolactone (PCL), a biodegradable polymer widely used in biomedical applications. The study investigates how light exposure and catalyst concentration influence polymerization efficiency, using tin(II) 2-ethylhexanoate [Sn(Oct)₂] as the catalyst in a non-polar toluene solvent at 90 °C. Reactions were conducted under either ambient light or black light bulb (BLB) illumination, with monomer-to-catalyst ratios of 1:1 and 200:1.

Proton nuclear magnetic resonance (¹H NMR) spectroscopy was used to analyze conversion efficiency by tracking the disappearance of monomer signals and appearance of characteristic PCL peaks. Results revealed …

Solubility Characterization Of Organic Molecules For Aqueous Organic Redox Flow Batteries, Anthony W. Ferrell, Harkeerith K. Vij, Seamus D. Jones

College of Engineering Summer Undergraduate Research Program

The major obstacle to renewable energy sources is a lack of long-term energy storage capabilities. Energy produced during the day dissipates, leaving insufficient electricity for at night. The goal of the project is to design an Aqueous Organic Redox Flow Battery (AORFB) to act as long-term energy storage. Work has been done using machine learning to identify suitable compounds for the batteries. In this work there was no indication as to the aqueous solubility of the molecules; this controls the device’s energy storage capabilities. We used a machine learning model to determine the aqueous solubility of slightly more than 3000 …

Poly(Thioether) Thermosets With Gated Photodegradation, Surabhi Jha

Dissertations

Photodegradable polymer networks are attractive due to the precise spatiotemporal control and large-area applicability of light. Chemical linkages that enable these polymer networks to be photo-responsive, also hinder their applicability in ambient light. Photostable and photodegradable networks have recently been reported to overcome this challenge by combining other stimuli with light for degradation. We report the design of a network that responds to a simultaneous, dual stimulus for photodegradation. We design poly(thioether acetal) networks with benzylidene acetal moieties that are known to undergo β-scission in the presence of free thiols. By blocking these free thiols with a thermally labile protecting …

Rational Design Of Peptide-Based Materials Informed By Multiscale Molecular Dynamics Simulations, Dhwanit Rahul Dave

Dissertations, Theses, and Capstone Projects

The challenge of establishing a sustainable and circular economy for materials in medicine and technology necessitates bioinspired design. Nature's intricate machinery, forged through evolution, relies on a finite set of biomolecular building blocks with through-bond and through-space interactions. Repurposing these molecular building blocks requires a seamless integration of computational modeling, design, and experimental validation. The tools and concepts developed in this thesis pioneer new directions in peptide-materials design, grounded in fundamental principles of physical chemistry. We present a synergistic approach that integrates experimental designs and computational methods, specifically molecular dynamics simulations, to gain in-depth molecular insights crucial for advancing the …

Characterization Of Interlayer Laser Shock Peening During Fused Filament Fabrication Of Polylactic Acid (Pla), Fabien Denise

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The field of additive manufacturing (AM) has gained a significant amount of popularity due to the increasing need for more sustainable manufacturing techniques and the adaptive development of complex product geometries. The problem is that AM parts routinely exhibit flaws or weaknesses that affect functionality or performance. Over the years, surface treatments have been developed to compensate certain flaws or weaknesses in manufactured products. Combining surface treatments with the modularity of additive manufacturing could lead to more adaptable and creative improvements of product functions in the future. The current work evaluates the feasibility of pursuing a new research axis in …

Covalent Adaptable Networks For Wood Coatings, Jachin Boaz Clarke

Materials Engineering

Wood swells and shrinks causing problems with seasonal humidity. Applying thick coatings of reactive finishes based on cross-linked polyurethane, epoxy, or polyesters can slow moisture-vapor exchange. However, the use of thick coatings leads to cracking and crazing sooner than thin finishes. This research proposes the addition of 3.3 mol % triazabicyclodecene, a conventionally used covalent adaptable network catalyst, in a commercially available polyester-based wood coating. The self-healing of the wood coating is tested using DMA stress relaxation and compression molding. The result from DMA renders inconclusive and compression molding indicates the novel wood coating oxidizes at elevated temperatures. The wood …

The Application Of Photoelectron Spectroscopies In Analyzing The Impact Of Interfacial Energetics On Perovskite Solar Cells, Tuo Liu

Theses and Dissertations--Chemistry

In recent years, organic-inorganic metal halide perovskites (HP) have garnered tremendous attention in photovoltaic research. This attention is attributed to their low cost and excellent optoelectronic properties, including large absorption coefficients, tunable bandgaps, long charge-carrier diffusion lengths, and low densities of deep trap states. Inverted p-i-n architecture perovskite solar cells (PSCs) are of intense interest and are generally regarded as more amenable to low-temperature solution processing. Nevertheless, the development of inverted PSCs is lagging the conventional architecture devices. Imperfect energy level alignments and charge carrier recombination, especially at the interface between perovskite and electron transport layers (ETLs), are two main …

Tools And Strategies For The Patterning Of Bioactive Molecules And Macromolecules, Daniel J. Valles

Dissertations, Theses, and Capstone Projects

Hypersurface Photolithography (HP) is a printing method for fabricating structures and patterns composed of soft materials bound to solid surfaces and with ~1 micrometer resolution in the x, y, and z dimensions. This platform leverages benign, low intensity light to perform photochemical surface reactions with spatial and temporal control of irradiation, and, as a result, is particularly useful for patterning delicate organic and biological material. In particular, surface- initiated controlled radical polymerizations can be leveraged to create arbitrary polymer and block- copolymer brush patterns. Chapter 1 will review the advances in instrumentation architectures from our group that have made these …

Degumming Of Hemp Fibers Using Combined Microwave Energy And Deep Eutectic Solvent, Bulbul Ahmed

LSU Master's Theses

Hemp is considered as one of the sustainable agricultural fiber materials. Degumming or surface modification of hemp bast is needed to produce single fibers for ensuing textile and industrial applications. The traditional degumming process necessitates a high amount of alkali, which causes detrimental environmental pollution. This study offers a new method to degum hemp fibers with reduced use of harmful alkali and precious water resources. In this work, hemp bast fibers were degummed by using combined microwave energy and deep eutectic solvent (DES). The properties of hemp fibers manufactured by this method were investigated and compared with the traditional alkali …

Phase-Field Modeling Of The Polymer Membrane Formation Process For Micro- And Ultra-Filtration, Michael Rosario Cervellere

Graduate Theses and Dissertations

Porous polymer membrane filters are widely used in separation and filtration process. Micro- and ultra-filtration membranes are commonly used in biopharmaceutical applications such as filtering viruses and separating proteins from a carrier solution. The formation of these membrane filters via phase inversion is a complex and interconnected process where varying casting conditions can have a wide variety of effects on the final membrane morphol- ogy. Tailoring membrane filters for specific performance characteristics is a tedious and time consuming process. The time and length scales of membrane formation make it extremely difficult to experimentally observe membrane formation. Modeling the membrane formation …

Atomic Oxygen Resistant Low Earth Orbit Stable Polymer Matrix Composites Employing Phenylphosphine Oxide Epoxy-Amines, Witold Fuchs

Dissertations

Atomic oxygen (AO) attacks polymer matrix composites (PMC’s) on the surfaces of spacecraft in low earth orbit (LEO) and threatens safe spacecraft operation and service life. Incorporating phenylphosphine oxide (PPO) groups into polymer chains offers a self-regenerating method of protection from AO but remains poorly understood. Herein, epoxies containing PPO groups were synthesized with increasing concentrations of phosphorus [P] from 0 to 8 wt % to investigate their AO resistance. Measurements confirmed the exposure of these materials to AO produces a passivation phosphate (POx) layer on the surface of the sample and the efficacy of the resultant layer was directly …

Development Of Biomaterials For Drug Delivery, Raquel De Castro

Graduate Theses and Dissertations

Drug delivery systems (DDS) have highly evolved in the last decades with the development of hydrogels and nanoparticles. However, high systemic uptake, side effects, low bioavailability, and encapsulation efficiency continue to be a major hurdle faced by such DDSs.

Nanoparticles and hydrogels can be specifically designed for targeted DDSs to mitigate some of the problems. This dissertation aimed to design two DDSs for ocular drug delivery and one for cancer treatment. The first project sought to develop chitosan nanoparticles (Cs-NP) using PEGDA as a copolymer to encapsulate gentamicin (GtS) for ocular drug delivery. Cs-NPs contain positive charges that can interact …

Valorization Of Xylan In Agroforestry Waste Streams, Harrison Appiah

Graduate Theses, Dissertations, and Problem Reports (ETD)

Valorization of Xylan in Agroforestry Waste Streams.

Harrison Appiah

Microwave-assisted deep eutectic solvent and gamma-valerolactone metallic chloride catalyzed conversion of xylan to furfural were investigated using a 2x3 factorial experimental design at two levels of percent microwave power, reaction time, and catalyst concentration. The levels of each factor studied were (20%, 60% microwave power, 2, 4 minutes, and 10, 20mg) respectively. The effect of three metallic chloride catalysts (LiCl, FeCl3.6H20, CuCl2) on the conversion of xylan to furfural was also investigated. The gamma-valerolactone-ferric chloride sent system exhibited the highest mean yield of furfural (56.50%). The next highest furfural yield of …

Multi-Level Analysis Of Atomic Layer Deposition Barrier Coatings On Additively Manufactured Plastics For High Vacuum Applications, Nupur Bihari

Dissertations, Master's Theses and Master's Reports

While hardware innovations in micro/nano electronics and photonics are heavily patented, the rise of the open-source movement has significantly shifted focus to the importance of obtaining low-cost, functional and easily modifiable research equipment. This thesis provides a foundation of open source development of equipment to aid in the micro/nano electronics and photonics fields.

First, the massive acceptance of the open source Arduino microcontroller has aided in the development of control systems with a wide variety of uses. Here it is used for the development of an open-source dual axis gimbal system. This system is used to characterize optoelectronic properties of …

In Depth Characterisation Of The Biomolecular Coronas Of Polymer Coated Inorganic Nanoparticles With Differential Centrifugal Sedimentation, André Perez-Potti, Hender Lopez, Beatriz Pelaz, Abuelmagd Abdelmonem, Mahmoud G. Soliman, Ingmar Schoen, Philip M. Kelly, Kenneth A. Dawson, Wolfgang J. Parak, Zeljka Krpetic, Marco P. Monopoli

Articles

Advances in nanofabrication methods have enabled the tailoring of new strategies towards the controlled production of nanoparticles with attractive applications in healthcare. In many cases, their characterisation remains a big challenge, particularly for small-sized functional nanoparticles of 5 nm diameter or smaller, where current particle sizing techniques struggle to provide the required sensitivity and accuracy. There is a clear need for the development of new reliable characterisation approaches for the physico-chemical characterisation of nanoparticles with significant accuracy, particularly for the analysis of the particles in the presence of complex biological fluids. Herein, we show that the Differential Centrifugal Sedimentation can …

Practical Adhesion Measurements In Organic Coatings; Advancing Understanding And Mechanical Methods Development, Diana Gottschalk

Dissertations

“Adhesion” can be considered either a mechanical or chemical phenomenon. The mechanical interpretation describes the difficulty of separating surfaces and is useful for quantifying performance within applications that depend on bulk and interfacial properties. Chemical adhesion describes interfacial resistance to chemical attack and does not depend on bulk properties. Predicting chemical failure through mechanical measurement is confounded by the influence of bulk properties. However, the prospect is attractive because of the robust tolerance for sample geometries, allowing experiments to resemble an end-use system. The present work's primary goal was to elevate mechanical methods to provide a detailed interfacial characterization of …

Preparation And Characterisation Of Heat Treated Oil Palm-Empty Fruit Bunch/High Density Polyethylene Composites, Nordin Nur Afifah

Student Works (2020-2029)

Natural fibre composites (NFCs) are composite materials, in which the reinforcing fibres are derived from renewable and carbon dioxide neutral resources such as wood or plants. NFC can be made by replacing synthetic fibres with various types of natural fibres. Oil palm empty fruit bunch (OPEFB) fibre and oil palm mesocarp fibre are two important types of fibrous materials left in the palm-oil industry. In this study, EFB will be used as a reinforcement to the high-density polyethylene (HDPE). EFB was heat-treated at 180°C using vacuum oven for one hour, extrusion compounded with HDPE at 10%, 20% and 30% weight …

Synthesis And Characterization Of Porous Carbon Composite Derived From Biomass Waste For Supercapacitor Application, Cheng Kim Sim

Student Works (2020-2029)

Energy storage devices have gradually dominated human daily activities and indispensable to economy development such as supercapacitor and battery. There are few factors determining the performance of supercapacitor and active material is one of the crucial. Therefore, biomass such as pineapple peel (PP) and green waste (GW) were preferred and prior mixed with manganese and tin carbonate to synthesize carbon composite (PP/GW-ZMO and PP/GW-ZTO) via combustion. Brunauer–Emmett–Teller (BET) was employed to study the textural properties with the highest specific surface area obtained in PP-C (1765.92 m2g-1) and GW-C (1613.92 m2g-1). The existence of composite materials was examined using x-ray diffraction …

Effect Of Post-Consumer Content And Bioplastic Incorporation On Polymeric Resin In Consumer Applications, Shelby Bicknell

Electronic Theses & Dissertations

Controversy surrounds the use of plastic products, primarily due to their potentially negative impact on the environment at the end of their lifecycle. The most widely used plastics are manufactured from petrochemicals such as petroleum, coal or natural gas. Petrochemical plastics are not able to readily breakdown in the environment, which aggravates the existing pollution problems. Fortunately, there are eco-friendly alternatives to petrochemical-based plastics. Bioplastics may be derived from renewable sources, biodegradable, or both. Bio-based plastics are plastics that may be derived from renewable biomass sources including, but not limited to, vegetable oils, cornstarch, straw, woodchips, and food waste. They …

Enhancement Of Phase Change Material Sorbitol By Nanoparticle Inclusion For Improving Thermal Energy Storage Capabilities, Joshua Kasitz

Mechanical Engineering Undergraduate Honors Theses

Thermal management of electronic devices has become an increasingly vital field of study with the rapid miniaturization of many key electrical components. With the significant improvement of semiconductor manufacturing and intensified focus on interconnects, electronic devices have decreased in size at an incredible rate. Decreasing spatial requirements is essential to improving device capabilities as the electronic system is able to incorporate more components. Currently, electronic systems are drastically limited by the capabilities of their cooling mechanisms. Smaller devices lead to large increases in the energy density of the system and require more powerful cooling systems to maintain proper component operating …

Gravity-Drawing Flexible Silicone Filaments As Fiber Optics And Model Foldamers, Katherine Snell

CMC Senior Theses

Here, we present a method of gravity-drawing polydimethylsiloxane (PDMS) silicone fibers with application as fiber optics and as model foldamers. Beginning as a viscous liquid, PDMS is cured using heat until its measured viscosity reaches 4000 mPa•s. The semi-cured elastomer is then extruded through a tube furnace to produce thin (diameters on the order of hundred micrometers) filaments with scalable lengths. PDMS is biocompatible, gas-permeable, flexible, and hydrophobic. Additionally, the PDMS surface hydrophobicity can be modified via UV exposure, O2 plasma, and corona discharge. We demonstrate the patternibility (i.e patterns of hydrophobicity) of PDMS fibers, adding complexity to potential foldamer …

Redox-Active Porous Organic Materials For Electrochemical Energy Storage Applications, K. Shamara Weeraratne

Theses and Dissertations

As the demand for renewable energy technologies grows, so does the need for cheaper, more efficient rechargeable batteries to store the energy. While lithium-ion battery (LIBs) technology is well established, it suffers from limited lithium supplies. Furthermore, the highly toxic transition metals used in the electrodes places a huge burden on the environment. Therefore, replacing lithium with more economical sodium metal in rechargeable batteries (i.e. sodium-ion batteries, SIBs) has garnered considerable attention. Despite the fact that sodium and lithium share similar electrochemical properties, which may cause the transition from lithium to sodium easier, the larger ionic radius of Na^{+ …}

Interfaces In Lead-Free Tin Perovskite Photovoltaics: An Investigation Of Energetics, Ion Mobility, Surface Modification, And Performance, Alex Boehm

Theses and Dissertations--Chemistry

Halide perovskites have generated tremendous interest as low-cost semiconductors for optoelectronics, such as photovoltaics, lasers, and light emitting diodes due to their extraordinary optical and transport properties. Perovskite photovoltaics in particular have demonstrated a meteoric rise in power conversion efficiencies and drawn considerable interest as a next-generation solar energy technology. The rapid development has centered around lead-based derivatives, and concerns regarding the toxicity of lead has sparked interest in low toxicity and more environmentally friendly perovskite derivatives. In this regime tin (Sn) is regarded as a prominent alternative owing to the ideal bandgap and reduced toxicity exhibited by Sn-halide perovskites. …

The Fabrication And Properties Of Magnetorheological Elastomers Employing Bio-Inspired Dopamine Modified Carbonyl Iron Particles, Yanfen Zhou, Lele Li, Wenyue Li, Shipeng Wen, Liang Jiang, Stephen Jerrams, Jianwei Ma, Shaojuan Chen

Articles

To obtain magnetorheological elastomers (MREs) with improved mechanical properties and exhibiting an enhanced magnetorheological (MR) effect, bio-inspired dopamine modification has been used to improve the functionality at the surface of carbonyl iron (CI) particles. Various techniques including x-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to confirm that a polydopamine (PDA) layer of about 27.5 nm had been successfully deposited on the surface of the carbonyl iron particles prior to their inclusion in the MRE composites. The magnetic properties of PDA modified CI particles were shown to be almost the same as those …