Polymer and Organic Materials Commons^™

Plastic Material Analysis And Bonding In Small Aquatic Vessels, Andrew R. Orr

Honors College Theses

This project presents the design and development of a suitable vessel for small-scale aquatic applications. The developed project is used for a remote-controlled duck hunting system, and the parameters of the design are based on the requirements for the system as a whole. Traditionally, plastics are fabricated using blow molding to create a single seamless form. However, for small-scale prototyping with limited resources, this method of fabrication is unsustainable for short-term, non-industrial design applications. As a result, an existing longer hull is selected and shortened to meet the required project length. The project evaluates multiple initial hull designs, ultimately selecting …

Made On Mars: Design And Manufacturing Of Structural Polymer-Regolith Composites, Pailey M. Vitale

Williams Honors College, Honors Research Projects

Human exploration of Mars is constrained by harsh environmental conditions and the prohibitive cost of transporting materials from Earth. Long-term sustainability requires the local production of mechanical and structural components using resources available on Mars, thereby minimizing payload mass. This project investigates polymer–regolith composites derived from atmospheric CO₂ and mineral-rich regolith as a pathway toward in-situ manufacturing. These composites, when compatible with additive manufacturing, could replace imported plastics, enable on-demand fabrication, and support closed-loop recycling systems. The objective is to design and evaluate polymer–regolith composites that maintain mechanical integrity and environmental resistance under Martian conditions, including extreme temperature swings, radiation …

An Overview Of Biomass-Derived Graphene Oxide And Its Characteristics For Future Sustainable Applications, Afif Wardana, Ahmad Nabil Shahab, Donanta Dhaneswara, Nofrijon Sofyan

Journal of Materials Exploration and Findings

The production of graphene oxide (GO) from biomass presents considerable promise as a sustainable alternative substitute for traditional semiconductors. Biomass waste, abundant and often underutilized worldwide, is distinguished by its high carbon content and regenerative characteristics, rendering it an optimal resource for sustainable material production. By heating its biopolymers, lignocellulosic biomass can be used as a new material to make graphene, which forms three-dimensional turbostratic crystallites. These crystallites, composed of partially defective aromatic carbon sheets with graphite-like characteristics, make it easier to create GO with specialized functions for cutting-edge applications. Its capability underscores the revolutionary potential of biomass waste in …

Characterization Of The Fatigue Threshold Behavior Of Uhmwpe, Bethany B. Smith, Anurag Roy, Robert O. Ritchie, Lisa A. Pruitt

Faculty Journal Articles

Ultra-high-molecular-weight-polyethylene (UHMWPE) has been the material of choice for bearings in total joint replacements (TJRs) for decades as a result of its excellent wear resistance, chemical inertness, energetic toughness, low friction, and biocompatibility. Utilization of this polymer in orthopedic devices requires oxidation, wear, and fatigue resistance. Balancing these important properties by tailoring processing techniques and modulating microstructural features has been an ongoing endeavor in the field. Research into the clinical applications of UHMWPE has primarily focused on the challenges of wear and oxidation while studies into the realm of fatigue have been more limited. Literature gaps exist in fully understanding …

Fire Fossils: Biomineral Infrastructures In Untangling Climates, Tanmayee More

Masters Theses

Diatoms drift, sediments sink, wildfires generate their own weather. Lightning strikes can blast sand into glass, and microscopic organisms do the same in the cold recesses of the ocean. What alchemies and metabolisms catalyze space, time, and energy? What are the thermodynamics of infrastructure in Climate Change?

Places, materials, and beings are afterimages. Through alchemical experiments, and multi-scalar imaging, I develop simulations of wildfires, and their profound, reverberating effects. In this thesis, a glass-meets-landscape experimental process enters these obscured conditions and renders new material relations for the built environment.

Incorporating Recycled And Repurposed Plastic Into 100% Reclaimed Asphalt Pavement, Basant Bhatt

Graduate Theses and Dissertations (2019 - present)

The increasing awareness of sustainability in the asphalt industry has driven the use of recycled materials like reclaimed asphalt pavement (RAP) and waste plastic. This study examines the incorporation of recycled polypropylene (rPP), recycled high-density polyethylene (rHDPE), and recycled low-density polyethylene (rLDPE) at 0.3%, 0.6%, and 0.8% dosages into 100% RAP, along with the warm mix asphalt additive Evotherm® P25. Laboratory tests were conducted to evaluate the mechanical and durability performance of the modified asphalt mixtures while rutting and fatigue life were evaluated using mechanistic-empirical (ME) analysis in PerRoad software. Both plastic type and dosage had a statistically significant impact …

Advanced Manufacturing Of Multifunctional Shape Memory Polymer Composites And Self-Healing Systems, John B. Konlan

LSU Doctoral Dissertations

The need for multifunctional light weight structures for engineering applications is on the rise. Multifunctional composites are desired because of their ability to combine multiple functionalities into one structure. The advantages of a high strength-to-weight ratio of multifunctional composites make them desirable and suitable for use in energy-efficient applications. Shape-memory polymers (SMPs) have attracted interest over the past several decades because of their multifunctional nature. They have found use in many applications such as aerospace, satellites, automobiles, textiles, and biomedical devices, where lightweight and multifunctionality are key. The self-healing nature of most SMPs makes them suitable for use in lightweight …

Reuse Of Calcium Carbonate (Caco3) Recovered From Discarded Carpets As Filler In Fiber-Reinforced Polymer (Frp) Composites, Roshan Devkota

Graduate Theses, Dissertations, and Problem Reports (ETD)

Over four billion pounds of carpet are discarded annually in the United States, making carpet waste a significant environmental concern. Calcium carbonate (CaCo₃) constitutes up to 45% of the mass of most synthetic carpets. Reusing this CaCo₃ as a filler in the rapidly growing fiber-reinforced polymer (FRP) industry, which is projected to reach USD 10.38 billion, presents a low-cost, practical approach to developing a market-based solution to post-consumer carpet waste.

This study investigates the reuse of CaCo₃ recovered from discarded carpet backing as a filler in FRP composites, focusing on its mechanical viability in comparison to virgin CaCo₃. The methodology …

Development Of Multifunctional Wood Composites With Integrated Phase Change Materials For Enhanced Thermal Management, Self-Healing, And Sustainability., Emmanuel Igbokwe

LSU Master's Theses

Abstract

This study focused on incorporating self-healing, flame retardancy, and energy harvesting capabilities into the wood composite to contribute to more sustainable and energy-efficient building practices. Oriented strand board has been widely used as sheath for roofing or dry walls in residential buildings. Residential buildings account for a large portion of energy consumption. Therefore, an oriented strand board with energy harvesting capability is highly desired. Additionally, flame retardancy and damage self-healing and end-of-life recycling are also critical features for buildings.

In this study, we prepared a novel oriented strand board by constructing sandwich structures. The face sheets of the sandwich …

Physics-Informed Machine Learning Methods For Inverse Design Of Multi-Phase Materials With Targeted Mechanical Properties, Yunpeng Wu

All Dissertations

Advances in machine learning algorithms and applications have significantly enhanced engineering inverse design capabilities. This work focuses on the machine learning-based inverse design of material microstructures with targeted linear and nonlinear mechanical properties. It involves developing and applying predictive and generative physics-informed neural networks for both 2D and 3D multiphase materials.

The first investigation aims to develop a machine learning method for the inverse design of 2D multiphase materials, particularly porous materials. We first develop machine learning methods to understand the implicit relationship between a material's microstructure and its mechanical behavior. Specifically, we use ResNet-based models to predict the elastic …

A Manufacturing-To-Response Pathway For Manufacturing Optimization Of Carbon Fiber Reinforced Polymer Composite Structures, Madhura Limaye

All Dissertations

Over the past decade, there has been an increased adoption of thermoplastic and thermoset based continuous carbon fiber reinforced polymer (CFRP) composites for structural applications in several industries. Among the different manufacturing methods, thermoforming process for thermoplastic based continuous CFRP’s offer a major advantage in reducing cycle times for large scale productions. Similarly, out-of-autoclave curing process for thermoset based continuous CFRP’s using heated tooling enables production of large composite structures. However, these manufacturing processes can have a significant impact on the structural performance of parts by inducing undesirable effects. These effects include inhomogeneous fiber orientations, thickness variations, and residual stresses …

Surface Treatments' Effects On The Capacitor's Dielectric Performance Under Electro-Thermal Stresses, Haider. M. Umran, Feipeng Wang

Karbala International Journal of Modern Science

Biaxial-oriented polypropylene (BOPP) films are characterized by unfavorable aging behavior because of their poor susceptibility to high temperatures, humidity, and high electric fields. This makes them unqualified to withstand harsh operating conditions, such as in capacitor applications. This study investigates the impact of annealing BOPP samples at 100 °C for five hours after fluorination at different times (15, 30, and 60 minutes) on their electrical and mechanical performance under electro-thermal stresses. Scanning electron microscope (SEM) images confirm that there is an increase in surface roughness and the formation of a dense layer of fluorine-containing groups monotonically with fluorination time. So, …

Engineering Nanofibers: Laboratory Characterization, Microstructural Analysis, And Image Processing Insights, Sayed Ahmadreza Razian, Mohammad Arjomandi, Kaspars Maleckis

UNO Student Research and Creative Activity Fair

Polymer nanofibers have attracted high interest in a wide array of applications, including biomaterial scaffolding, textiles, sensors, reinforcement in composites, and filtration systems. Many of these applications combine nanofibers into non-woven fabrics for better properties and easier manipulation. The properties and performance of nanofiber-based fabrics are affected by various microstructure parameters, including fiber alignment, diameter, and gap sizes between the nanofibers. These structural parameters can be controlled by adjusting various process parameters during manufacturing process, but the exact process parameter-microstructure relationships vary depending on the polymer system and need to be studied individually. The goal of this study is to …

Molecular Modeling Of Phenolic Resin For Carbon-Carbon Composites, Ivan Gallegos

Dissertations, Master's Theses and Master's Reports

One of the most difficult challenges associated with space exploration is terrestrial atmospheric reentry due to the high thermal loads generated. Carbon carbon (C/C) composites have been used as heat shielding materials due to their high strengthto- weight ratio and thermal properties and their applications include heat shielding for various high temperature environments. C/C composites are manufactured by polymer-infiltration pyrolysis (PIP) via cycles of curing and pyrolysis of a prepreg which can be costly and take up to several days. Thus, C/C composites ideal candidates for computationally-driven optimization techniques, such as a multiscale Integrated Computational Materials Engineering (ICME) approach, by …

Novel Precursors For Carbon Fiber Prepared By Direct Carbonization, Leah Noble

Theses and Dissertations--Chemical and Materials Engineering

For decades carbon fiber-based composites have been most heavily employed in lightweight, structural applications where low density and high strength are necessary, most notably within the aerospace industry. However, the advancement of carbon fiber into a wider array of industries has largely been limited by the high financial and energetic costs associated with its manufacture. Moreover, with an increasing societal emphasis on sustainability, there is an ever-growing desire for low-energy carbon fiber production pathways. One such pathway is the conversion of precursor fiber to carbon fiber by direct carbonization, wherein the energy-intensive, pre-carbonization stabilization step is omitted from the carbonization …

Cfrp Delamination Density Propagation Analysis By Magnetostriction Theory, Brandon Eugene Williams

All Dissertations

While Carbon Fiber Reinforced Polymers (CFRPs) have exceptional mechanical properties concerning their overall weight, their failure profile in demanding high-stress environments raises reliability concerns in structural applications. Two crucial limiting factors in CFRP reliability are low-strain material degradation and low fracture toughness. Due to CFRP’s low strain degradation characteristics, a wide variety of interlaminar damage can be sustained without any appreciable change to the physical structure itself. This damage suffered by the energy transfer from high- stress levels appears in the form of microporosity, crazes, microcracks, and delamination in the matrix material before any severe laminate damage is observed. This …

Carbon Fibers From Athabasca Oil-Sand Asphaltenes, Blake Reardon

All Theses

Carbon fibers possess ultra-high specific strength and modulus. Therefore, the material is popular in aerospace, automotive, and sports industries. Approximately 95% of all carbon fibers are spun from a high-cost precursor, polyacrylonitrile (PAN). There is a need for a cheaper grade of carbon fiber for low-cost applications because about half of carbon fiber cost is associated with precursor cost. A promising alternative to the high-cost PAN precursor is petroleum-based asphaltene. Asphaltenes are highly aromatic and have a high carbon content but lack the purity of the PAN precursor. Processes like the molten- sodium desulfurization upgrading have been used to harvest …

Interlaminar Tensile Properties Of Unidirectional And Woven Carbon Fiber Reinforced Toughened Epoxy Laminates, Eric Timothy Casey, Sean Mckalip Thompson

Materials Engineering

This project aims to develop a dataset on interlaminar tensile strength comparing unidirectional and woven thermoset matrix carbon fiber composites keeping ply count, matrix material, and fiber diameter constant. The interlaminar tensile strength is an important property relating to the delamination failure mode. Interlaminar tensile strength is determined using the ASTM D6415 testing standard. This test is a modified four-point bend test using a 90° curved beam test specimen. Laminates were produced by laying up pre-impregnated carbon fiber sheets onto a curved beam tooling. The unidirectional laminate was produced with 20 plies in a [0,0,90,0,0]₄ layup pattern. The woven …

Bio-Based Food Packaging Material For Intelligent Food Packaging Applications For Chicken Fillets, Kalpani Y. Perera, Amit K. Jaiswal, Swarma Jaiswal, Shubham Sharma

Articles

Bionanocomposite packaging is made up of bio- based materials that have high performance activity and are ecologically sustainable alternatives to packaging made of synthetic polymers. Intelligent packaging retains track of the state of the food and the environment in which it is stored, and communicates relevant changes to the consumer through visualization or other methods. The aim of this study was to develop a bionanocomposite intelligent packaging material by utilising sodium alginate, gelatin, nanoclay and curcumin. Sodium alginate, gelatin film incorporated with Curcumin (Cur), and Nanoclay (NC) in various concentrations (0% W/V, 0.5% W/V, 1% W/V and 1. 5% W/V) …

Bbt Acoustic Alternative Top Bracing Cadd Data Set-Norev-2022jun28, Bill Hemphill

STEM Guitar Project’s BBT Acoustic Kit

This electronic document file set consists of an overview presentation (PDF-formatted) file and companion video (MP4) and CADD files (DWG & DXF) for laser cutting the ETSU-developed alternate top bracing designs and marking templates for the STEM Guitar Project’s BBT (OM-sized) standard acoustic guitar kit. The three (3) alternative BBT top bracing designs in this release are
(a) a one-piece base for the standard kit's (Martin-style) bracing,
(b) 277 Ladder-style bracing, and
(c) an X-braced fan-style bracing similar to traditional European or so-called 'classical' acoustic guitars.

The CADD data set for each of the three (3) top bracing designs includes …

Evaluating The Effects Of Granulated Rubber And Glass Fibers In Polymer Concrete As A Structural Material For Wafer Grinding Machines, Kevin Gabriel Kuehn, Philip Randall Streeter

Materials Engineering

Polymer concrete is a composite material used to replace cast iron and steel in wafer grinding machines for vibration damping. During the grinding and lapping processes of manufacturing silicon wafers, excessive vibrations may cause subsurface damage which requires additional polishing and reduces yield. Nine compositions containing various levels of granulated rubber and glass fibers were manufactured. CRM WRF-10 granulated rubber was examined at 0%, 5%, and 10% and Corning Cem-Fil glass fibers were added at 0%, 0.5%, and 1% by weight. Smooth-On EpoxAcast 690 epoxy resin was held constant at 16% for each composition. Crushed granite aggregate from Martin Marietta, …

Sustainable Composites From Agricultural And Petroleum Waste, Menisha S. Karunarathna

All Dissertations

Green gas emission has been a pervasive and persistent subject of debate for a prolonged period. The soaring number of industries and vehicle fuel emissions presage a concomitant rise in global CO₂ emissions. Global cement production is responsible for 8% of the total CO₂ release, yet, the production continues due to the surging demand. Hence, there is an ongoing quest to find alternatives for cement and building materials produced with zero to lower CO₂ emissions. The work presented in this dissertation focuses on finding recyclable, zero CO₂ gas-producing high sulfur biocomposites materials, which can compete with …

Prospects For Using Metal-Polymer Composite Structures In The Gear Manufacturing, Umid Mamasobirov, Shoraxmat Shoobidov, A F. Husanboyev

Technical science and innovation

In this paper, some thermoplastic polymer composites and filler composites for the production of metal-polymer gear transmissions are presented. Efforts have been made to expand the raw material base and identify ways to increase the durability of gears through technological and design measures.

Rational Design Of Flexible And Stretchable Electronics Based On 3d Printing, Yuanhang Yang

Theses and Dissertations

Flexible and stretchable electronics have been considered as the key component for the next generation of flexible devices. There are many approaches to prepare the devices, such as dip coating, spin coating, Mayer bar coating, filtration and transfer, and printing, etc. The effectiveness of these methods has been proven, but some drawbacks cannot be ignored, such as lacking pattern control, labor consuming, requiring complex pretreatment, wasting conductive materials, etc.

In this investigation, we propose to adopt 3D printing technology to design flexible and stretchable electronics. The objective is to rationally design flexible and stretchable sensors, simplify the preparation process, form …

Molecular Modeling Of High-Performance Polymers, Sagar Umesh Patil

Dissertations, Master's Theses and Master's Reports

High-performance polymers are extensively used in the aerospace and aeronautics industries due to their low density, high specific strength, and high specific stiffness. These properties along with better infiltration with reinforcements [carbon nanotubes (CNTs), glass, etc.] capability make them an excellent candidate to fabricate Polymer Matrix Composites (PMCs) tailored for specific applications. The applications range from products used daily to deep space exploration. These materials are subjected to varying temperatures and pressures during fabrication and in service. Therefore, the evolution of their intrinsic properties needs to be studied and their ability to sustain extreme environmental conditions in outer space needs …

Seaweed Polysaccharide In Food Contact Materials (Active Packaging, Intelligent Packaging, Edible Films, And Coatings), Kalpani Y. Perera, Shubham Sharma, Amit K. Jaiswal, Swarna Jaiswal

Articles

Food contact materials (FCMs) are materials that come in contact with food products such as food packaging which play a significant role in the food quality and safety. Plastic, which is a major food packaging material, harms the eco-system, wildlife, and the environment. As a result, numerous researches have been in progress on alternative polymers, which has similar properties as plastic but is also environmentally friendly (biodegradable). In recent years, the utilization of seaweed polysaccharides has piqued interest due to its biodegradability, non-toxicity, antioxidant capabilities, and excellent film formation ability. However, it has a number of drawbacks such as low …

Tools And Strategies For The Patterning Of Bioactive Molecules And Macromolecules, Daniel J. Valles

Dissertations, Theses, and Capstone Projects

Hypersurface Photolithography (HP) is a printing method for fabricating structures and patterns composed of soft materials bound to solid surfaces and with ~1 micrometer resolution in the x, y, and z dimensions. This platform leverages benign, low intensity light to perform photochemical surface reactions with spatial and temporal control of irradiation, and, as a result, is particularly useful for patterning delicate organic and biological material. In particular, surface- initiated controlled radical polymerizations can be leveraged to create arbitrary polymer and block- copolymer brush patterns. Chapter 1 will review the advances in instrumentation architectures from our group that have made these …

Rapid Annealing Of Perovskite Solar Cell Thin Film Materials Through Intense Pulse Light., Amir Hossein Ghahremani

Electronic Theses and Dissertations

Perovskite solar cells (PSCs) have garnered a great attention due to their rapid efficiency improvement using cheap and solution processable materials that can be adapted for scalable high-speed automated manufacturing. Thin film perovskite photovoltaics (PVs) are typically fabricated in an inert environment, such as nitrogen glovebox, through a set of deposition and annealing steps, each playing a significant role on the power conversion efficiency (PCE), reproducibility, and stability of devices. However, atmospheric processing of PSCs would achieve lucrative commercialization. Therefore, it is necessary to utilize materials and methods that enable successful fabrication of efficient PSCs in the ambient environment. The …

Phase-Field Modeling Of The Polymer Membrane Formation Process For Micro- And Ultra-Filtration, Michael Rosario Cervellere

Graduate Theses and Dissertations

Porous polymer membrane filters are widely used in separation and filtration process. Micro- and ultra-filtration membranes are commonly used in biopharmaceutical applications such as filtering viruses and separating proteins from a carrier solution. The formation of these membrane filters via phase inversion is a complex and interconnected process where varying casting conditions can have a wide variety of effects on the final membrane morphol- ogy. Tailoring membrane filters for specific performance characteristics is a tedious and time consuming process. The time and length scales of membrane formation make it extremely difficult to experimentally observe membrane formation. Modeling the membrane formation …

Investigation Of Membrane Based Processes For Biomedical Applications, Efecan Pakkaner

Graduate Theses and Dissertations

As substantial developments were achieved in nanotechnology and polymer engineering, especially in the last few decades, the use of membranes and membrane-based procedures was found to be expanding into more and more research and development areas; including biological engineering, life sciences and biomedical engineering. Not only have they been the main focus of meaningful research, but they have also been the main pieces of the solutions to very thorny problems encountered within a wide range of applications from microfluidics to water treatment, thanks to their versatility, cost-effectiveness and biocompatibility, when compared to conventional separation techniques. To celebrate and embrace these …