Polymer and Organic Materials Commons^™

A Platform For Fast Detection Of Let-7 Micro Rna Using Polyaniline Fluorescence And Image Analysis Techniques, Partha P. Sengupta

Master's Theses

The project describes a new strategy for transducing hybridization events through modulating intrinsic properties of the electroconductive polymer polyaniline (PANI). When DNA based probes electrostatically interact with PANI, its fluorescence properties are increased, a phenomenon that can be enhanced by UV irradiation. Hybridization of target nucleic acids results in dissociation of probes causing PANI fluorescence to return to basal levels. By monitoring restoration of base PANI fluorescence as little as 10^-11 M (10 pM) of target oligonucleotides could be detected within 15 minutes of hybridization. Detection of complementary oligos was specific, with introduction of a single mismatch failing to …

Process Development For Compression Molding Of Hybrid Continuous And Chopped Carbon Fiber Prepreg For Production Of Functionally Graded Composite Structures, Corinne Marie Warnock

Master's Theses

Composite materials offer a high strength-to-weight ratio and directional load bearing capabilities. Compression molding of composite materials yields a superior surface finish and good dimensional stability between component lots with faster processing compared to traditional manufacturing methods. This experimental compression molding capability was developed for the ME composites lab using unidirectional carbon fiber prepreg composites. A direct comparison was drawn between autoclave and compression molding methods to validate compression molding as an alternative manufacturing method in that lab. A method of manufacturing chopped fiber from existing unidirectional prepreg materials was developed and evaluated using destructive testing methods. The results from …

Effects Of Expected Service Life Exposures On The Functional Properties And Impact Performance Of An American Football Helmet Outer Shell Material, David E. Krzeminski

Dissertations

The purpose of this dissertation is to gain a greater scientific understanding of the changes in functional material properties and impact performance of an American football helmet outer shell material under expected service life exposures. The research goals are to (i) quantify chemical, physical, thermal, and mechanical degradation of an American football outer shell material under expected environmental conditions and (ii) develop a linear drop test impact protocol to employ expected on-field impact conditions to American football helmet components and a plaque-foam (i.e., shell-liner) surrogate. Overall, a step-wise progression of analysis was demonstrated to concurrently quantify and understand changes in …

Hybrid Aryl-Ether-Ketone And Hyperbranched Epoxy Networks, John Misasi

Dissertations

In this dissertation, relationships between chemical structures, cure kinetics and network architectures are correlated to bulk mechanical properties for novel, hybrid epoxy-amine networks. The work is split into two primary sections: the first is the synthesis and characterization of multifunctional glassy networks based on aryl-ether-ketone diamine curatives, while the second is based on the synthesis and characterization of hyperbranched epoxy polymers and their resulting networks.

Three aryl-ether-ketone (AEK) diamines of increasing molecular weights were synthesized and used to cure 4,4’-tetraglycidylether of diaminodiphenylmethane (TGDDM); the resulting networks were compared to 4,4’-diaminodiphenyl sulfone cured TGDDM. Architectural differences were created by varying cure …

Polyacrylonitrile Copolymers: Effects Of Molecular Weight, Polydispersity, Composition, And Sequencing On Thermal Ring-Closing Stabilization, Jeremy D. Moskowitz

Dissertations

Controlled polyacrylonitrile (PAN)-based carbon fiber precursors with defined molecular weights, polydispersities, compositions, and architectures have been prepared for their study on thermal ring-closing stabilization behavior. PAN and its copolymers of number average molecular weights exceeding 170,000 g/mol were successfully synthesized via low temperature reversible addition-fragmentation chain transfer (RAFT) polymerization. RAFT polymerizations of PAN-based precursors were compared to conventional free radical solution polymerizations with a focus on the effects of molecular weight and polydispersity on structural evolution and cyclization efficiency. When RAFT polymerization was extended to copolymers, it was found that RAFT copolymers achieved greater cyclization intensities and improved thermal stability …

Development Of Dual-Cure Hybrid Polybenzoxazine Thermosets, Jananee Narayanan Sivakami

Dissertations

Polybenzoxazines are potential high performance thermoset replacements for traditional phenolic resins that can undergo an autocatalytic, thermally initiated ring - opening polymerization, and possess superior processing advantages including excellent shelf-life stability, zero volatile loss and limited volumetric shrinkage. The simplistic monomer synthesis and availability of a wide variety of inexpensive starting materials allows enormous molecular design flexibility for accessing a wide range of tailorable material properties for targeted applications. Despite the fact, once fully cured, benzoxazines are difficult to handle due to their inherent brittleness, leaving a very little scope for any modifications. The motivation of this dissertation is directed …

Volatile Condensible Material Deposition In Leo Simulated Environment, Jinya Pu

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Room Temperature Vulcanized (RTV) silicone and compounds are widely used in outer-space for bonding or potting spacecraft components. In geosynchronous equatorial orbit (GEO), the silicone may outgas species which can condense on optically sensitive surfaces and degrade their performance, therefore shortening the lifetime of spacecraft. In low-earth-orbit (LEO), the silicone rubber is subject to an energetic and corrosive environment. Atomic oxygen (AO) and ultraviolet radiation can cause abrasion and degradation of the silicone rubber, cause changes in existing condensed VCM films and affect the properties of VCM films condensing in this atmosphere. Experiments were performed to simulate GEO conditions. In …

Influence Of Carbon Nanofillers On The Curing Kinetics Of Epoxy-Amine Resin, Luigi Vertuccio, Salvatore Russo, Marialuigia Raimondo, Khalid Lafdi, Liberata Guadagno

Chemical and Materials Engineering Faculty Publications

The cure kinetics of an epoxy resin based on the tetrafunctional epoxy precursor N,N′-tetraglycidyl methylene dianiline-(TGMDA) hardened with 4,4-diaminodiphenyl sulfone is investigated. The influence of carbon nanofillers (carbon nanotubes, carbon nanofibers, and graphene based nanoparticles) on the cure kinetic is studied. Kinetic analysis is performed by dynamic and isothermal differential scanning calorimetry (DSC).

In dynamic experiments, the activation energy was computed using an advanced isoconversional method while under isothermal conditions, the Kamal’s model of diffusion control was applied to simulate the systems throughout the curing process. The isothermal analysis shows that the introduction of the diluent decreases, …

Characterization Of Hydrogel Curing Methods For Manufacturability, Hannah E. Brown, Rebecca K. Kramer, Edward L. White

The Summer Undergraduate Research Fellowship (SURF) Symposium

In the field of soft robotics, hydrogels possess material properties that allow them to function as both soft strain sensors and dielectric elastomer actuators. However, there is still much that needs to be understood about the curing process of hydrogels and the resulting material characteristics before manufacturing these devices can be accomplished. In this study, we investigated the effect of curing time and sample volume on the as-cured material properties of acrylamide-based hydrogels hydrated with lithium and magnesium chloride salt solutions. Samples were cured at room temperature, 60° C and 100° C, and the resulting changes in mechanical stiffness and …

Fracture Mechanics-Based Simulation Of Pv Module Delamination, Dominic I. Jarecki, Johanna B. Palsdottir, Peter Bermel, Marisol Koslowski

The Summer Undergraduate Research Fellowship (SURF) Symposium

Photovoltaic (PV) cells are rapidly growing as a renewable alternative to fossil fuels like coal, oil, and natural gas. However, greater adoption has also reduced government subsidies, placing the onus of making solar panels economically competitive on innovative research. While multiple methods have been considered for reducing costs, with each reduction in cost comes the associated peril of reduction in quality and useful lifetime. Several problems considered solved have now resurfaced as potential failure mechanisms with the introduction of cheaper PV cell technologies. However, to remain economically viable, PV modules will not only have to become cheaper, they will have …

Synthesis, Characterization, And Thermoelectric Properties Of Radical Siloxanes, Arnold J. Eng, Bryan Boudouris, Edward P. Tomlinson, Martha Emily Hay

The Summer Undergraduate Research Fellowship (SURF) Symposium

More than half of the annual energy consumption in the United States is lost as waste heat. Polymer-based thermoelectric devices have the potential to utilize this waste heat both sustainably and cost-effectively. Although conjugated polymers currently dominate research in organic thermoelectrics, the potential of using polymers with radical pendant groups have yet to be realized. These polymers have been found to be as conductive as pristine (i.e., not doped) poly(3-hexylthiophene) (P3HT), a commonly-used charge-transporting conjugated polymer. This could yield promising avenues for thermoelectric material design as radical polymers are more synthetically tunable and are hypothesized to have a high Seebeck …

Thermal And Mechanical Properties Of Polymers Using Molecular Dynamics, Daniel Glass, Alejandro Strachan, Lorena Alzate-Vargas, Chunyu Li, Benjamin Haley

The Summer Undergraduate Research Fellowship (SURF) Symposium

Polymer systems have gained attention during the past years because of their technological and industrial applications. Simulations, particularly molecular dynamics, are very useful for exploring properties of amorphous polymers, without using experiments. Our goal is to create a readily-available tool that will perform MD simulations in order to get thermal and mechanical properties (Glass transition temperature, Young Modulus) of the polymers. The work that has been done will be part of a tool to help people to learn about polymer properties including Glass Transition Temperature. We model some polymers at a scale of 10,000 atoms. The tool uses LAMMPS to …

Morphology-Property Relationship For Binary Organic Thin Films, Alyssa Lynn Griffin

Master's Theses

Organic thin films can be readily mass-produced through solution-based fabrication methods including ink-printing and solution-casting because their light weight, flexibility, and inexpensive sources. Their applications range from organic field-effect transistors (OFET), organic solar cells (OSC), to organic light emitting diodes (OLEDs). Compared with pure component films, binary organic thin films (BOTF) allows for novel characteristics and specialized features to handle more demanding tasks. Due to the complex intermolecular interactions in BOTF, various microscopic phases with different morphological and electronic properties may be formed and this information is difficult to extract through conventional bulk measurements.

Organic thin films can be readily …

Efficiency Enhancement In Solution Processed Organic And Organic–Inorganic Hybrid Perovskite Solar Cells, Zhengguo Xiao

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Solution processed thin film photovoltaic devices are one of the most promising renewable energy sources. Organic solar cells have been intensively studied due to their advantages of light-weight, flexibility and low-cost materials and manufacturing. The organic-inorganic hybrid perovskite materials have recently shown great potential application in solar cells. The PCE increased dramatically from 3.8% in 2009 to a certified efficiency of 20.1% in 2014. In this dissertation, we focus on the efficiency enhancement for solution processed organic and organic-inorganic solar cells.

In Chapter 2, I demonstrated that the crystallinity of the ferroelectric polymer P(VDF-TrFE) at the organic active layer/ electrode …

Spotlight On Graphene Research From The Middle East, Kathleen A. Lehman

University Libraries Faculty Publications and Presentations

In an extension to the 2011 article “Reviews of Science for Science Librarians: Graphene” (Lehman 2011), this paper seeks to continue exploring the trend of graphene research but limits its focus to the research production of countries in the Middle East. In addition to reporting on the research output of this group of countries, this article will also examine the most prolific Middle Eastern graphene authors,their supporting institutions and funding agencies, the most cited publications from this group, the journals most used for publication of their work, and the general trend in graphene research growth in the Middle East. As …

Temperature Dependent Surface Reconstruction Of Freely Suspended Films Of 4-N-Heptyloxybenzylidene-4-N-Heptylaniline, Daniel E. Martinez Zambrano

Lawrence University Honors Projects

Surfaces of freely suspended thick films of 4-n-heptyloxybenzylidene-4-n-heptylaniline (7O.7) in the crystalline-B phase have been imaged using non-contact mode atomic force microscopy. Steps are observed on the surface of the film with a height of 3.0 +/- 0.1 nm corresponding to the upright molecular length of 7O.7. In addition, we find that the step width varies with temperature between 56 and 59 degrees C. The steps are many times wider than the molecular length, suggesting that the steps are not on the surface but instead originate from edge dislocations in the interior. Using a strain model for liquid crystalline layers …

Effect Of Heat Treatment On The Mechanical Properties In Natural Bamboo, Austin Levy, Mackenzie Kirkpatrick

Materials Engineering

Previous studies have shown that heat treatments have the ability to improve mechanical strength and stiffness in hardwood species. Compared to structural hardwoods, bamboo is a more sustainable and globally viable renewable resource. Therefore, Bambusoides vivax (timber bamboo) culms were fabricated into flat, rectangular cross-section samples with varying cellulose content to be heat treated and tested for mechanical properties. All samples were heat treated (HT) twice. The first HT was a normalization of all samples at 103 +/- 3 °C. The second HT was performed at various times and temperatures ranging from 130°C to 170°C for 0.5 to 3 hours. …

Minimizing Sheet Resistance Of Organic Photovoltaic Cell Top Contact Electrode Layer: Silver Nanowire Concentration Vs. Conductive Polymer Doping Concentration, Caitlyn Cook

Materials Engineering

The top contact electrode layers of nine organic photovoltaic cells were prepared with two varying factors: three Silver nanowire (AgNW) densities deposited on a conductive polymer doped with three concentrations. Silver’s low sheet resistance of 20-Ω/sq is hypothesized to lower the sheet resistance of the anode layer and thus enhance the overall efficiency of the cell. Four-point probe measurements indicated that increasing AgNW density in the top contact electrode layer of an organic photovoltaic cell significantly reduces sheet resistance from 52.2k-Ω/sq to 18.0 Ω/sq. Although an increase in doping concentration of the conductive polymer reduced sheet resistance in low AgNW …

Effect Of Time Delay Between Etching And Adhesive Bonding (“Outlife” Time) On Lap-Shear Strength Of Aluminum Alloys Using Environmentally-Friendly P2 Etch, Josh Barkhimer, Matthew Erich, Gokul Nair

Materials Engineering

Raytheon Company currently uses a Forest Products Laboratory (FPL) paste etchant for preparing aluminum surfaces for adhesive bonding, and FPL is a source of hazardous hexavalent chromium. The goal of this study was to evaluate a less-toxic P2 paste etchant as a possible replacement. Coupons of 2024-T3, 6061-T6, and 7075-T6 grades of aluminum alloy were solvent-degreased, abrasively cleaned, and etched at room temperature using P2 paste following a strict protocol adopted from Raytheon. Coupons were then left exposed to air for assigned time intervals (or “outlife” times) of 0, 1, 4, 8, 16, and 63 or 72 hours. The aluminum …

Molecular Dynamics Investigation Of The Arabinan-Cellulose Interface For Cellulose Nanocomposite Applications, Luke Thornley

Materials Engineering

Atom level computer simulations of the arabinan and cellulose interface were performed to better understand the mechanisms that give arabinan-cellulose composites (ArCCs) their strength with the goal to improve man-made ArCCs. The molecular dynamics (MD) software LAMMPS was used in conjunction with the ReaxFF/c force field to model the bond between cellulose and arabinan. A cellulose nanocrystal with dimensions 51 x 32 x 8 Å was minimized with various weight percent of water, 0%, 3%, 5%, 8%, 10%, and 12%. After the system was equilibrated for at least 100,000 femtoseconds, an arabinan molecule composed of 8 arabinose rings was added …

Self-Contained Breathing Apparatus For Firefighter With A Permanent Stoma, Jason Delgadillo, Aaron Wheeler, Zachary Wishbow

Biomedical Engineering

The purpose of this project was to create a unique SCBA (self-contained breathing apparatus) for a firefighter named Chris Gauer. This prototype consists of a SCBA headgear connected to a polycarbonate-formed stoma mask with a medical-grade sanitary silicone hose.

Effect Of Surfactant Architecture On Conformational Transitions Of Conjugated Polyelectrolytes, Greg A. Braggin

Master's Theses

Water soluble conjugated polyelectrolytes (CPEs), which fall under the category of conductive polymers, possess numerous advantages over other conductive materials for the fabrication of electronic devices. Namely, the processing of water soluble conjugated polyelectrolytes into thin film electronic devices is much less costly as compared to the processing of inorganic materials. Moreover, the handling of conjugated polyelectrolytes can be performed in a much more environmentally friendly manner than in the processing of other conjugated polymers because conjugated polyelectrolytes are water soluble, whereas other polymers will only dissolve in toxic organic solvents. The processing of electronic devices containing inorganic constituents such …

Predictive Modeling Of Oxygen Transmission Through Micro-Perforations For Packaging Applications, Ayman Abdellatief, Bruce A. Welt, Jason Butler, Eric Mclamore, Arthur Teixeira, Sanjay Shukla

Journal of Applied Packaging Research

Methods for creating precise perforations in respiring produce packaging are being increasingly adopted. Knowledge of oxygen transfer through perforated packaging and oxygen distribution in packages is necessary for successful packaging design of fresh produce. An approach to modeling perforated packaging performance was developed using a cylindrical chamber with precision perforations using Fick’s second law. The model was simulated using two techniques including Finite Element Method (FEM) using commercially available software and Finite Volume Method (FVM) through programming. Perforations were approximated as a source term in the second method. Both simulation techniques showed trends similar to experimental data.

Feasibility Study: The Evaluation Of Polymer Coatings To Prevent Weathering Of Weak Rocks, Lauren Distler

Senior Honors Projects, 2010-2019

The weathering and erosion of weak rocks along roadways can cause dangerous and potentially fatal rockfalls.   Various slope stabilization methods exist, but each presents a set of challenges and trade-offs.   The focus of the project is to understand the feasibility of utilizing of a polymerbased slope stabilization technique. Rock samples were collected along US Route 33 in Virginia and West Virginia, and preliminary tests were conducted to evaluate the absorption of water (% mass) and durability. The study evaluates three polymer options in regard to the following criteria: adhesion to rock, layer thickness, semi-permeability, insolubility, and non-toxicity. The polymer selection …

Material Coefficient Of Thermal Expansion Investigation For Use In Additive Manufacturing Fused Deposition Modeling For Composite Tooling, Daniel Joseph Miller

Master's Theses

Polymer matrix composites are being used to manufacture light weight, high stiffness aircraft structures. These structures are often manufactured from carbon fiber reinforced epoxy. When these structures are damaged, they must be repaired to restore strength to the component to avoid the cost and logistics of having replacements parts. Occasionally, these repairs require tooling in order to make a quality repair, however, tooling generally has a long lead time. Additive manufacturing could be used to manufacture rapid tooling to create tooling for composite repairs. The issue is that polymer printed tooling has a much higher coefficient of thermal expansion (CTE) …

Cure Kinetics, Morphologies, And Mechanical Properties Of Thermoplastic/Mwcnt Modified Multifunctional Glassy Epoxies Prepared Via Continuous Reaction Methods, Xiaole Cheng

Dissertations

The primary goal of this dissertation is to develop a novel continuous reactor method to prepare partially cured epoxy prepolymers for aerospace prepreg applications with the aim of replacing traditional batch reactors. Compared to batch reactors, the continuous reactor is capable of solubilizing and dispersing a broad range of additives including thermoplastic tougheners, stabilizers, nanoparticles and curatives and advancing epoxy molecular weights and viscosities while reducing energy consumption.

In order to prove this concept, polyethersulfone (PES) modified 4, 4’-diaminodiphenylsulfone (44DDS)/tetraglycidyl-4, 4’-diaminodiphenylmethane (TGDDM) epoxy prepolymers were firstly prepared using both continuous reactor and batch reactor methods. Kinetic studies confirmed the chain …

Electrospinning Of Polycaprolactone Core-Shell Nanofibers With Anti-Cancer Drug, Sakib Iqbal, Mujibur Khan, Saheem Absar, Andrew Diamanduros, Samuel Chambers

GS4 Student Scholars Symposium

Encapsulation of a model anti-cancer drug, 5-Fluorouracul (5-FU) into biocompatible core-shell nanofibers of polycaprolactone (PCL) nanofibers was fabricated using a coaxial electrospinning process. Our work aims to solve these issues using a novel method of fabrication of fibers featuring confinement of drugs within a biodegradable core-shell structure, thereby permitting sustained release of drugs to specific sites of treatment, such as tissues affected with tumor cells. The coaxial electrospinning was performed using a sheath polymer solution consisting of a 14 wt% PCL solution and a 5 wt% solution of 5-FU as the core solution. Dimethylformamide (DMF) was used as the solvent …

Optimization Of Graphene-Based Materials Outperforming Host Epoxy Matrices, Liberata Guadagno, Marialuigia Raimondo, Luigi Vertuccio, Marco Mauro, Gaetano Guerra, Khalid Lafdi, Biagio De Vivo, Patrizia Lamberti, Giovanni Spinelli, Vincenzo Tucci

Chemical and Materials Engineering Faculty Publications

The degree of graphite exfoliation and edge-carboxylated layers can be controlled and balanced to design lightweight materials characterized by both low electrical percolation thresholds (EPT) and improved mechanical properties. So far, this challenging task has been undoubtedly very hard to achieve.

The results presented in this paper highlight the effect of exfoliation degree and the role of edge-carboxylated graphite layers to give self-assembled structures embedded in the polymeric matrix. Graphene layers inside the matrix may serve as building blocks of complex systems that could outperform the host matrix. Improvements in electrical percolation and mechanical performance have been obtained by a …

Process And Apparatus For Manufacturing Grease, Lou A. T. Honary, James E. Wesley

Patents (University of Northern Iowa)

A process and corresponding apparatus and system for use in preparing soaps from fatty acid containing oil compositions, and in turn, for preparing greases by the use of such soaps in combination with one or more base oils.

Methods For Analyzing The Structure Of Creases In Heat Sealed Paperboard Packages, Ville Leminen, Petri Mäkelä, Panu Tanninen, Juha Varis

Journal of Applied Packaging Research

Press-forming of paperboard has been previously studied by several authors. A point of interest regarding gas tight heat sealing of the packages are the creases in the package. The objective of this article was to study and compare different microscopic imaging methods to research an optimal imaging method for the formation of creases in the press-forming process of polymer coated paperboard trays. The studied methods were: Scanning electrode microscopy (SEM), X-ray Microtomography, Optical light microscopy and Polarized light microscopy. All four tested methods delivered clear images. Casting of the samples in an acrylic resin and light microscope imaging was found …