Polymer and Organic Materials Commons^™

Tuning Ion Mobility And Molecular Confinement In High-Performance Polymer Electrolytes For Energy Storage, Ezzeldien Yousef Muhammed Yousef

Theses and Dissertations

This research addresses the critical energy density limitations of aqueous supercapacitors, which are traditionally constrained by the narrow electrochemical stability window (ESW) of water 1.23 V. By employing two distinct molecular engineering strategies, this study developed high-performance electrolyte systems that significantly extend voltage stability and thermal resilience.

The first system, CsBr@PAM/HA, utilizes a polyacrylamide and hyaluronic acid hydrogel matrix. This system exploits the chaotropic nature of Cs⁺ ions to disrupt the aqueous hydrogen-bonding network, enhancing ionic conductivity to 104 mS cm^-1. Through systematic salt screening, CsBr was identified as the optimal electrolyte, enabling a stable 2.0 V …

Thermally Induced Color Changes In Iron Oxide Pigments Used In Architectural Coatings, Han Diep

Master's Theses

The 2025 Palisades Fire was one of the most destructive wildfires in the history of Los Angeles, destroying thousands of structures and severely impacting the communities after. This widespread destruction demonstrated an urgent need for more effective wildfire prevention strategies. Architectural coatings do not only provide aesthetics and protection against environmental conditions but can also function as a thermal indicator when a fire breaks out. This study examines the thermally induced color transformation of iron oxide pigments, commonly used in earthtone paint, to provide information relevant to CAL FIRE for improved analysis of wildland-urban interface (WUI) fire behavior and mitigation …

Adsorption Of Pfas On Bridged Functionalized Organosilica Materials, Elisha Lawerh Kabutey

Electronic Theses and Dissertations

PFAS are hazardous contaminants that have a devastating impact on human health and the environment. Their hazardous nature has led to the development of various adsorption methods for removing these contaminants from water sources. In this study, functionalized organosilica materials were synthesized from bis[3-(trimethoxysilyl)propyl] amine using the sol-gel method. The surface amino groups of the organosilica were converted into amine hydrochloride groups. Their adsorption properties were evaluated using salts of perfluorooctanoic acid, perfluorooctanesulfonic acid, and perfluorobutanesulfonic acid. Results showed excellent adsorption capacity of the materials. Adsorption of PFAS leads to particle agglomeration and flotation of the spent material. A column …

Engineering Silicone Magnetic Fluids For Localized Radiation Attenuation During Ocular Melanoma Brachytherapy, Zachary L. Caprow

All Dissertations

Ocular melanoma is commonly treated using plaque brachytherapy; however, radiation-induced damage to healthy ocular tissues frequently results in partial or complete vision loss. This work investigates the development of an injectable, magnetically responsive silicone magnetic fluid designed to localize adjacent to the tumor and attenuate low-energy gamma radiation during treatment.

The material system consists of iron oxide nanoparticles surface-functionalized with a siloxane polymer, in which the nanoparticles provide magnetic responsiveness and radiation attenuation, while the polymer coating ensures colloidal stability, injectability, and biocompatibility. A one-pot synthetic approach was developed wherein a functionalized siloxane polymer containing iron-affinitive groups was reacted with …

Bio-Papcz: Corn Starch-Based Composite Bioplastic Reinforced With Pineapple Leaf Fiber (Palf), Zinc Oxide (Zno), And Polyvinyl Alcohol (Pva), Marvin C. Caya, Shervin Austin C. Huang, Jovar Khalel J. Maghari, Ruel M. Levida

Sinaya: A Philippine Journal for Senior High School Teachers and Students

Plastic pollution poses a serious global threat, as petroleum-based plastics persist for centuries, and their surging production of over 450 million tons overwhelms ecosystems (Ritchie et al., 2023). Using a quantitative experimental research design, the study examined the effects of varying concentrations of cornstarch-based bioplastic reinforced with pineapple leaf fiber (PALF), polyvinyl alcohol (PVA), and zinc oxide (ZnO) on the bioplastic’s tensile strength and soil degradability. Sample C2 (ZnO 3.0 %w/w; PVA 9.0 %w/w) demonstrated the optimal tensile properties with a tensile strength of 0.76 MPa and an elongation at break of 6.40%, which was attributed to the addition of …

An Overview Of Biomass-Derived Graphene Oxide And Its Characteristics For Future Sustainable Applications, Afif Wardana, Ahmad Nabil Shahab, Donanta Dhaneswara, Nofrijon Sofyan

Journal of Materials Exploration and Findings

The production of graphene oxide (GO) from biomass presents considerable promise as a sustainable alternative substitute for traditional semiconductors. Biomass waste, abundant and often underutilized worldwide, is distinguished by its high carbon content and regenerative characteristics, rendering it an optimal resource for sustainable material production. By heating its biopolymers, lignocellulosic biomass can be used as a new material to make graphene, which forms three-dimensional turbostratic crystallites. These crystallites, composed of partially defective aromatic carbon sheets with graphite-like characteristics, make it easier to create GO with specialized functions for cutting-edge applications. Its capability underscores the revolutionary potential of biomass waste in …

Upcycling Commodity Polymers To Advanced Materials For Energy And Environmental Sustainability, Anthony Griffin-Espinoza

Dissertations

Synthetic polymers play an essential role in nearly every aspect of our lives. Extending beyond single-use packaging, polymeric material design has progressed to attain tailorable architectures granting exceptional performance across advanced applications, including carbon-fiber reinforced polymer composites for aerospace, conductive materials for soft electronics, and drug carriers for biomedicine. While highly promising, intricately designed polymers needed to achieve excellent performance often have limited processability, complex synthetic methods, and expensive precursors. Furthermore, due to a lack of recyclability, commodity polymer waste streams result in both environmental impacts and a substantial loss of economic value. This dissertation focuses on developing robust strategies …

Understanding Structure-Property Relationships Within Polyolefin-Derived Vitrimer Systems, Mikaela Sadri

Dissertations

Polyolefins are extremely ubiquitous materials due to their satisfactory material properties, ease of synthesis, and low cost. Unfortunately, their extensive use has led to a global plastic waste mismanagement problem. As such, notable efforts have recently focused on converting these commodity polymers into vitrimers, or dynamic networks, to extend their use-life and tailor their properties. However, the fundamental polymer physics of these emerging materials, remain largely underexplored, hindering their widespread implementation. To address this challenge and enable a more sustainable future, the overarching goal of my dissertation research is to understand the fundamental structure-property relationships within complex polyolefin-derived vitrimer systems. …

Poly(Pyridinium Salt)S Containing 9,9-Bis(4- Aminophenyl)Fluorene Moieties With Various Organic Counterions Exhibiting Both Lyotropic Liquid-Crystalline And Light-Emitting Properties, Pradip K. Bhowmik, David King, Haesook Han, Andras F. Wacha, Matti Knaapila

Chemistry and Biochemistry Faculty Research

Main-chain conjugated and non-conjugated polyelectrolytes are an important class of materials that have many technological applications ranging from fire-retardant materials to carbon-nanotube composites, nonlinear optical materials, electrochromic materials for smart windows, and optical sensors for biomolecules. Here, we describe a series of poly(pyridinium salt)s-fluorene containing 9,9-bis(4-aminophenyl)fluorene moieties with various organic counterions that were synthesized using ring-transmutation polymerization and metathesis reactions, which are non-conjugated polyelectrolytes. Their chemical structures were characterized by Fourier transform infrared (FTIR), proton (1H) and fluorine 19 (19F) nuclear magnetic resonance (NMR) spectrometers, and elemental analysis. They exhibited polyelectrolytic behavior in dimethyl sulfoxide. Their lyotropic liquid-crystalline phases were …

Myceli-Yum: Elucidating Structure-Property Relationships For Polymer Degradation By Mycelial Digestion, Jordan Scott Ford

Master's Theses

Since the industrial entrance of polymer plastic materials, plastic has become ubiquitous in both everyday use and waste. Due to inefficiencies and knowledge gaps, current recycling methods are not able to account for the high scale of plastic waste, resulting in the bulk of this waste being landfilled, mishandled, and deposited in the environment. Mycelium, the microorganism responsible for fruiting mushroom bodies and mold growth, holds potential to reduce plastic waste and can potentially be utilized as a method of industrial recycling. Following a drug-design approach, the active site of mycelial enzymes responsible for natural biopolymer degradation have been assessed …

Tailoring The Morphology Of Block Copolymers Via Solvent-Vapor Annealing, Bayleigh Madelin Loving

Honors Theses

Triblock polystyrene-polyisobutylene-polystyrene (PS-PIB-PS) copolymers have widespread applications from thermoplastic elastomers to protective coatings for ballistic applications. The incompatibility between the soft PIB and hard PS phases leads to phase separation and subsequent formation of morphological domains like lamellae and cylinders. The structures are stabilized by physical crosslinks, which can greatly improve the toughness of the triblock systems by preventing chain pullout during tensile deformation. We tailored the morphologies (achieving different morphologies with the same block copolymer) by changing the annealing conditions of the block copolymers. Solvent vapor annealing was used to selectively activate the mobility of a particular block, causing …

Mechanistic Investigation Of Ring-Opening Polymerization Of Polycaprolactone Using Tin(Ii) Catalysts: Ligand Effects And Biomedical Applications, Eva-Larue M. Barber

Honors Scholar Theses

This research explores the mechanistic aspects of ring-opening polymerization (ROP) of ε-caprolactone (CL) to produce polycaprolactone (PCL), a biodegradable polymer widely used in biomedical applications. The study investigates how light exposure and catalyst concentration influence polymerization efficiency, using tin(II) 2-ethylhexanoate [Sn(Oct)₂] as the catalyst in a non-polar toluene solvent at 90 °C. Reactions were conducted under either ambient light or black light bulb (BLB) illumination, with monomer-to-catalyst ratios of 1:1 and 200:1.

Proton nuclear magnetic resonance (¹H NMR) spectroscopy was used to analyze conversion efficiency by tracking the disappearance of monomer signals and appearance of characteristic PCL peaks. Results revealed …

Effects Of High Temperature Compaction On 3d Printed Carbon Fiber Reinforced Polymer Composites, John D. Barber

Mechanical & Aerospace Engineering Theses & Dissertations

The aim of this dissertation was to study the effects of hot temperature compaction (HTC) upon the polymorphism and the mechanical behavior of an additively manufactured (AM), carbon fiber reinforced polyamide (PA6). Different pressure and temperature levels during HTC were tested to determine the overall effect upon the mechanical behavior and the material crystalline composition. Treated, carbon fiber reinforced PA6 samples were analyzed using differential scanning calorimetry, x-ray diffraction, thermogravimetric analysis, scanning electron microscopy, double cantilever beam testing and three-point bending testing. When considered with respect to as-printed samples, an HTC temperature of 190°C combined with 80 psi pressure resulted …

Solid-State Crystallization Of Zeolites And Their Use In Plastic Upcycling Applications, Yixin Liao

Doctoral Dissertations

Plastics have been an irreplaceable component of modern technology as well as everyday life. They have brought much convenience to us with their characteristics of great malleability, durability, and stability. The versatile and low-cost nature of plastics also enables their wide engagement in many modern industries including automobile, medical, communication as well as aerospace. Polyethylene (“PE”), made from polymerization of ethylene, is one of the most widely used plastics in the world. Being cheap, flexible, and long-lasting, they are extensively used in the packaging industry, especially for plastic bags and other sorts of containers. However, the durability of plastics, on …

Biobased Acrylate Composites With Enhanced Strength For Additive Manufacturing, Nicole Wagner, Joseph Mcwherter

Engineering Faculty Articles and Research

With the expanding use of polymers in additive manufacturing, sustainable resins for use in vat photopolymerization are required to reduce their environmental impact. One promising approach to achieve this is to incorporate biobased fillers that replace the acrylates in photopolymer resins as ‘green’ alternatives. In this study, photopolymer composites consisting of a methacrylate resin with varying calcium carbonate powder content between 0 and 50 wt.% were investigated. A digital light processing technique was used to fabricate tensile test specimens for mechanical testing. Good printability, dimensional accuracy, and good interlayer adhesion were observed for composite resin formulations that incorporated calcium carbonate …

Influence Of Glycopolymer Structure On Amphiphilic, Hybrid, Linear Branched Block Copolymer Properties For Use In Biomedical Applications, Kevin Green

Dissertations

The focus of this dissertation is evaluating and adding fundamental knowledge regarding the structure-property relations of glycopolymers used in the design of hybrid block copolymers (HBC) that are cable of self-assembling into delivery vehicles for biomedical applications. A shift to the utilization of natural materials in the design and fabrication of drug-delivery vehicles has garnered significant attention. Understanding the effects of linear glycopolymers content and composition on the resulting HBCs properties can provide valuable insight into how these materials may be tailored for use in targeted biological applications.

The first chapter introduces current literature on the need for improvement in …

Solubility Characterization Of Organic Molecules For Aqueous Organic Redox Flow Batteries, Anthony W. Ferrell, Harkeerith K. Vij, Seamus D. Jones

College of Engineering Summer Undergraduate Research Program

The major obstacle to renewable energy sources is a lack of long-term energy storage capabilities. Energy produced during the day dissipates, leaving insufficient electricity for at night. The goal of the project is to design an Aqueous Organic Redox Flow Battery (AORFB) to act as long-term energy storage. Work has been done using machine learning to identify suitable compounds for the batteries. In this work there was no indication as to the aqueous solubility of the molecules; this controls the device’s energy storage capabilities. We used a machine learning model to determine the aqueous solubility of slightly more than 3000 …

Chemical Recycling Of Bio-Based Polyurethane Foams: Evaluating Bio-Based Glycols In Comparison To Petroleum-Based Glycols, Anirudh Thorbole Mr.

Electronic Theses & Dissertations

The paradigm shift towards bio-based polyurethane foams (bio-PUF) has significantly increased post-consumer waste. To address this issue, this research represents a novel approach to enhance sustainable development in the recycling industry by replacing traditional petroleum-based glycols with sustainable bio-based alternatives. This study explores the glycolysis of bio-PUF using bio-based SG-522 glycol and polyethylene glycol (PEG) for comparison. The findings from this research as outlined, reveal no significant differences in depolymerization time between the two glycols, achieving proper depolymerization and high recovery yields of over 95% after solvent purification. Comprehensive FT-IR and NMR analyses confirmed the successful degradation of bio-PUF and …

Poly(Thioether) Thermosets With Gated Photodegradation, Surabhi Jha

Dissertations

Photodegradable polymer networks are attractive due to the precise spatiotemporal control and large-area applicability of light. Chemical linkages that enable these polymer networks to be photo-responsive, also hinder their applicability in ambient light. Photostable and photodegradable networks have recently been reported to overcome this challenge by combining other stimuli with light for degradation. We report the design of a network that responds to a simultaneous, dual stimulus for photodegradation. We design poly(thioether acetal) networks with benzylidene acetal moieties that are known to undergo β-scission in the presence of free thiols. By blocking these free thiols with a thermally labile protecting …

Characterization Of Interlayer Laser Shock Peening During Fused Filament Fabrication Of Polylactic Acid (Pla), Fabien Denise

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The field of additive manufacturing (AM) has gained a significant amount of popularity due to the increasing need for more sustainable manufacturing techniques and the adaptive development of complex product geometries. The problem is that AM parts routinely exhibit flaws or weaknesses that affect functionality or performance. Over the years, surface treatments have been developed to compensate certain flaws or weaknesses in manufactured products. Combining surface treatments with the modularity of additive manufacturing could lead to more adaptable and creative improvements of product functions in the future. The current work evaluates the feasibility of pursuing a new research axis in …

Characterization Of Mechanically Recycled Polylactic Acid (Pla) Filament For 3d-Printing By Evaluating Mechanical, Thermal, And Chemical Properties And Process Performance, Mahsa Shabani Samghabady

All Theses

Polylactic acid (PLA) is a biopolymer made from renewable resources such as sugar and corn. PLA filament is a popular material used in Fused Deposition Modeling (FDM) 3D-printing. While this material has many advantages, all the failed parts, support structures, rafts, nozzle tests, and the many prototype iterations during the 3D-printing process contribute to the plastic pollution and release of greenhouse gases. Although PLA is biodegradable, it can take years to degrade in landfills. Instead of throwing away PLA waste and buying new filaments, PLA can be recycled. Amongst the different recycling technologies, mechanical recycling is the most environmentally friendly. …

Covalent Adaptable Networks For Wood Coatings, Jachin Boaz Clarke

Materials Engineering

Wood swells and shrinks causing problems with seasonal humidity. Applying thick coatings of reactive finishes based on cross-linked polyurethane, epoxy, or polyesters can slow moisture-vapor exchange. However, the use of thick coatings leads to cracking and crazing sooner than thin finishes. This research proposes the addition of 3.3 mol % triazabicyclodecene, a conventionally used covalent adaptable network catalyst, in a commercially available polyester-based wood coating. The self-healing of the wood coating is tested using DMA stress relaxation and compression molding. The result from DMA renders inconclusive and compression molding indicates the novel wood coating oxidizes at elevated temperatures. The wood …

Enhancing Compatibility And Mechanical Properties Of Natural Rubber Composites, Krisma Yessi Sianturi, Adam Febriyanto Nugraha, Belle Kristaura, Mochamad Chalid

Journal of Materials Exploration and Findings

Pure natural rubber (NR) exhibits low mechanical properties, necessitating the incorporation of additives like vulcanizing agents and fillers. Carbon black and silica, conventional fillers, are relatively expensive and not environmentally friendly. This study explores using Oil Palm Empty Fruit Bunch (OPEFB) fiber as an affordable, abundant, and biodegradable alternative filler for NR. However, compatibility issues arise between the nonpolar NR and the polar OPEFB fiber. A latex-starch hybrid coupling agent (CA (NR-St)) was added to the composite formulation to address this. NR, OPEFB fiber, and the coupling agent were mixed using an open roll mill with a 10 phr OPEFB …

Separation Of Organic Acids Through Direct Catalysis From Sugars, Katelyn Robinson

Chemical Engineering Undergraduate Honors Theses

Society relies on plastic products, whether they are single use or durable. A downside of plastic is that the most common type is a product of oil and oil is not only a limited resource but also a climate-damaging resource. Polylactic acid (PLA) is a bio-based, biodegradable plastic. However, the process of converting biomass to polylactic acid polymer has the largest environmental impact of the PLA production process, so alternative methods of conversion are needed (Moretti et al., 2021). The polylactic acid polymer can be made with lactic acid, which can be converted from glucose.

The Influence Of Diamine Curing Additives On The Network Architecture Of Phthalonitrile Thermosetting Polymers, Tyler J. Richardson

Dissertations

Phthalonitrile monomers undergo diamine-promoted polymerization by a complex reaction mechanism involving two competitive cure pathways, forming two primary network architectures: linear polyisoindoline chains and branched triazine crosslinks. The influence of the diamine curing additive on the polymerization pathway, and the influence of the resulting network architectures on cured network properties, have not been adequately explored within the phthalonitrile field. Two structurally different diamine curing additives, bis[4-(3-aminophenoxy)phenyl] sulfone (mBAPS) and 1,3-phenylenebis((4-(4-aminophenoxy)phenyl)methanone) (AEK-134), were studied for the polymerization of resorcinol phenylphosphate phthalonitrile (RPPhPN), where the influence of diamine structure and concentration on the polymerization behavior, network architecture, and bulk thermal and thermomechanical …

Hydrothermal Liquefaction Of Saccharina Latissima For The Production Of Biofuel, Mayokun A. Oke

Mechanical Engineering Theses

We performed hydrothermal liquefaction of brown macroalga (Saccharina latissima) in the presence of homogenous and heterogenous catalysts such as KOH, Na₂CO₃, Pd/C, HZSM-5, Ce/HZSM-5, and Ni/SiO₂-Al₂O₃ in hot compressed water, to investigate their effects on product yield and composition in the biocrude. To investigate hydrocarbon production, we used methanol as co-solvent (methanol-to-water 1/4 vol.%) and as the only liquefaction solvent. We carried out the experiments in a batch reactor at 330^oC and 120-130 bar, and varying temperature, algae-to-water ratio, residence time, and pretreatment method. The biocrude yields …

Polyethersulfone Thin-Film Nanocomposite Membrane Embedded With Amine-Functionalized Graphene Oxide For Desalination Applications, Ahmed Bahaeldin

Theses and Dissertations

Thin-film nanocomposite (TFN) desalination membranes were prepared based on a polyethersulfone (PES) support, where the polyamide (PA) layer was embedded with amine-functionalized graphene oxide (GO). The effect of adding various concentrations of functionalized and un-functionalized GO on the desalination performance, hydrophilicity, and morphology of the membranes was additionally assessed throughout this work. Scanning electron microscopy (SEM) measurements were used to assess the morphology of the membranes in combination with Brunauer-Emmett-Teller (BET) analysis. Contact angle measurements were used to gauge the hydrophilicity of the synthesized membranes. The membrane with the best desalination performance contained 1x10^-3 wt/vol% of functionalized GO in …

The Application Of Photoelectron Spectroscopies In Analyzing The Impact Of Interfacial Energetics On Perovskite Solar Cells, Tuo Liu

Theses and Dissertations--Chemistry

In recent years, organic-inorganic metal halide perovskites (HP) have garnered tremendous attention in photovoltaic research. This attention is attributed to their low cost and excellent optoelectronic properties, including large absorption coefficients, tunable bandgaps, long charge-carrier diffusion lengths, and low densities of deep trap states. Inverted p-i-n architecture perovskite solar cells (PSCs) are of intense interest and are generally regarded as more amenable to low-temperature solution processing. Nevertheless, the development of inverted PSCs is lagging the conventional architecture devices. Imperfect energy level alignments and charge carrier recombination, especially at the interface between perovskite and electron transport layers (ETLs), are two main …

Bbt Acoustic Alternative Top Bracing Cadd Data Set-Norev-2022jun28, Bill Hemphill

STEM Guitar Project’s BBT Acoustic Kit

This electronic document file set consists of an overview presentation (PDF-formatted) file and companion video (MP4) and CADD files (DWG & DXF) for laser cutting the ETSU-developed alternate top bracing designs and marking templates for the STEM Guitar Project’s BBT (OM-sized) standard acoustic guitar kit. The three (3) alternative BBT top bracing designs in this release are
(a) a one-piece base for the standard kit's (Martin-style) bracing,
(b) 277 Ladder-style bracing, and
(c) an X-braced fan-style bracing similar to traditional European or so-called 'classical' acoustic guitars.

The CADD data set for each of the three (3) top bracing designs includes …

Bbt Side Mold Assy, Bill Hemphill

STEM Guitar Project’s BBT Acoustic Kit

This electronic document file set covers the design and fabrication information of the ETSU Guitar Building Project’s BBT (OM-sized) Side Mold Assy for use with the STEM Guitar Project’s standard acoustic guitar kit. The extended 'as built' data set contains an overview file and companion video, the 'parent' CADD drawing, CADD data for laser etching and cutting a drill &/or layout template, CADD drawings in AutoCAD .DWG and .DXF R12 formats of the centerline tool paths for creating the mold assembly pieces on an AXYZ CNC router, and support documentation for CAM applications including router bit specifications, feeds, speed, multi-pass …