Polymer and Organic Materials Commons^™

Silica Nanoparticle-Based Coatings With Superhydrophilic And Superhydrophobic Properties, Robert Andrew Fleming

Graduate Theses and Dissertations

Superhydrophilic and superhydrophobic surfaces have potential for implementation into a variety of fields, including self-cleaning surfaces, anti-fogging transparent materials, and biomedical applications. In this study, sandblasting, oxygen plasma treatments, silica nanoparticle films, and a low surface energy fluorocarbon film were employed to change the natural surface wettability of titanium, glass, and polyethylene terephthalate (PET) substrates, with an aim to produce superhydrophilic and superhydrophobic behavior. The effects of these surface modifications are characterized by water contact angles (WCAs), surface wetting stability, surface morphology and roughness, surface elemental composition, and optical transmittance measurements. The results show that stable superhydrophilic and superhydrophobic surfaces …

Design, Fabrication, Testing Of Cnt Based Isfet And Characterization Of Nano/Bio Materials Using Afm, Zhuxin Dong

Graduate Theses and Dissertations

A combination of Carbon Nanotubes (CNTs) and Ion Selective Field Effect Transistor (ISFET) is designed and experimentally verified in order to develop the next generation ion concentration sensing system. Micro Electro-Mechanical System (MEMS) fabrication techniques, such as photolithography, diffusion, evaporation, lift-off, packaging, etc., are required in the fabrication of the CNT-ISFET structure on p-type silicon wafers. In addition, Atomic Force Microscopy (AFM) based surface nanomachining is investigated and used for creating nanochannels on silicon surfaces. Since AFM based nanomanipulation and nanomachining is highly controllable, nanochannels are precisely scratched in the area between the source and drain of the FET where …

Prediction Of Compressive Creep Bhaviour In Flexible Polyurethane Foam Over Long Time Scales And At Elevated Temperatures, Conor Briody, Barry Duignan, Stephen Jerrams, Stephen Ronan

Articles

Compressive creep gradually affects the structural performance of flexible polymeric foam material over extended time periods. When designing components, it is often difficult to account for long-term creep, as accurate creep data over long time periods or at high temperatures is often unavailable. This is mainly due to the lengthy testing times and/or inadequate high temperature testing facilities. This issue can be resolved by conducting a range of short-term creep tests and applying accurate prediction methods to the results. Short-term creep testing was conducted on viscoelastic polyurethane foam, a material commonly used in seating and bedding systems. Tests were conducted …

A Silicon Carbide Based Solid-State Fault Current Limiter For Modern Power Distribution Systems, Erik Darnell Johnson

Graduate Theses and Dissertations

The fault current limiter represents a developing technology which will greatly improve the reliability and stability of the power grid. By reducing the magnitude of fault currents in distribution systems, fault current limiters can alleviate much of the damage imposed by these events. Solid-state fault current limiters in particular offer many improved capabilities in comparison to the power system protection equipment which is currently being used for fault current mitigation. The use of silicon carbide power semiconductor devices in solid-state fault current limiters produces a system that would help to advance the infrastructure of the electric grid.

A solid-state fault …

Pulse Sharpening Effects Of Thin Film Ferroelectric Transmission Lines, Robert J. Sleezer

Graduate Theses and Dissertations

Advances in material science have resulted in the development of electrically nonlinear high dielectric thin film ferroelectrics, which have led to new opportunities for the creation of novel devices. This dissertation investigated one such device: a low voltage nonlinear transmission line (NLTL). A finite element simulation of ferroelectric transmission lines showed that NLTLs are capable of creating shockwaves. Additionally, if the losses are kept sufficiently low, it was shown that voltage gain should be possible. Furthermore, a method of accounting for material dispersion was developed. Results from simulations including material dispersion showed that temporal solitons might be possible from a …

Titanium Aluminum Nitride Films Deposited By Ac Reactive Magnetron Sputtering: Study Of Positioning Effect In An Inverted Cylindrical Magentron Sputtering System, George C. Vandross Ii

Graduate Theses and Dissertations

TiAlN films were deposited on glass substrates by AC magnetron sputtering at 2 kW with constant Argon and Nitrogen gas flow rates to study the effects of positioning on the deposited films. The deposition system used was an ICM-10 IsoFlux cylindrical magnetron sputtering chamber. The samples were placed in different positions and tilts with respect to the location of the Titanium and Aluminum targets in the chamber. It was found that with change in position and application of tilts, deposited films acquired different physical and chemical properties. It is believed that the differences in these properties were caused by to …

P3ht:Pcpdtbt:Pcbm Multi- Polymer Single Layer Solar Cells, Ted Andreas

Physics

OPV efficiencies are limited by their narrow absorption; rather than using tandem architecture to overcome this obstacle, our group combined P3HT and PCPDTBT into a single layer BHJ solar cell that achieved 2.0% PCE. This is 33% higher than the pure P3HT control from this group, proving that multi-polymer solar cells have the potential to outperform their single-polymer components.

Biaxial Bending And Lateral-Torsional Instability Of Imperfect Frp I-Beams Including Effects Of Retrofitting, Jodi Marie Knorowski

Civil & Environmental Engineering Theses & Dissertations

This thesis presents the outcome of a theoretical and experimental study of the behavior of Fiber Reinforced Polymer (FRP) I-beams susceptible to lateral-torsional instability or when subjected to biaxial bending. Laboratory experiments involved application of vertical and horizontal static loads to a 4 x 4 x ¼ in. I-beam with various lengths, and the resulting displacement, twist, and strain were recorded. In the vertical direction, the beam was loaded from different reference load heights with respect to the shear center of the beam. The governing biaxial flexure and torsion differential equations were modified to account for the presence of initial …

Fabrication And Characterization Of Biocomposites From Polylactic Acid And Bamboo Fibers, Sarah E. Royse

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Environmental concerns have been motivating research in the field of biodegradable materials, especially those from biological sources. Polylactic acid (PLA) is one biopolymer with the potential to replace some standard synthetic polymers. PLA is currently used for fibers, medical sutures, and some packaging, but is still used very little compared with synthetic polymers. One thing that can be done to expand the potential applications of PLA is to add fibers to create composite materials. Bamboo is a good choice for these fibers because it is abundant in many parts of the world, grows very quickly, and is widely unused. Composites …

Atomistic Simulations Of Defect Nucleation And Intralayer Fracture In Molybdenum Disulphide During Nanoindentation, James A. Stewart

Graduate Theses and Dissertations

Molybdenum disulphide (MoS2) is a layered, hexagonal crystal that has a very low coefficient of friction. Due to this low coefficient of friction, MoS2 has become a well-known solid lubricant and liquid lubricant additive. As such, nanoparticles of MoS2 have been proposed as an additive to traditional liquid lubricants to provide frictional properties that are sensitive to different temperature and pressure regimes. However, to properly design these MoS2 nanoparticles to be sensitive to different temperature and pressure regimes, it is necessary to understand the mechanical response of crystalline MoS2 under mechanical loading. Specifically, the fundamental mechanism associated with the nucleation …

Semiconductor Nanocrystals: From Quantum Dots To Quantum Disks, Zheng Li

Graduate Theses and Dissertations

The bottom-up colloidal synthesis opened up the possibility of finely tuning and tailoring the semiconductor nanocrystals. Numerous recipes were developed for the preparation of colloidal semiconductor nanocrystals, especially the traditional quantum dots. However, due to the lack of thorough understanding to those systems, the synthesis chemistry is still on the empirical level. CdS quantum dots synthesis in non-coordinating solvent were taken as a model system to investigate its molecular mechanism and formation process, ODE was identified as the reducing agent for the preparation of CdS nanocrystals, non-injection and low-temperature synthesis methods developed. In this model system, we not only proved …

Wireless Temperature Monitoring System For The Cal Poly Pilot Winery, Caitlin Devaney

Materials Engineering

This project, with an interdisciplinary group of two computer engineers and one materials engineer, was seeking to implement an automated temperature monitoring system which is affordable and easy to use, as well as adaptable to any arrangement and scale of a winemaker’s fermentation setup. My goal, as the materials engineer, was to design, fabricate, and test the enclosure, for the wireless nodes that are placed in the wine fermentation tanks, and the materials used for the node enclosure. For the enclosure of the system, materials selection was completed using CES software using limitations of only polymer materials which absorb less …

Blunt Impact Performance Evaluation Of Helmet Lining Systems For Military And Recreational Use, Jaclyn Siniora, Ryan Taylor, Darren Suey

Industrial Technology and Packaging

With the increasing problem in collegiate athletes experiencing injuries to the brain, different helmet liners where put to the test to see which liner provided athletes the greatest protection under specific conditions.

This senior project evaluates five different liners in football helmets. Each of the helmet liners were tested at three different temperatures: hot, cold, and ambient. Each helmet had seven different impact locations which were put to the test. The project was designed to be used to test ACH military combat liners as well. Due to shipping bottle necks the ACH combat liners have been left to future Cal …

Biaxial & Twist Testing Of Composite Carbon-Fiber Sandwich Panels For Automotive Racing Vehicles, Erik Eckberg

Materials Engineering

Composite sandwich panels were constructed with 4-ply plain weave carbon-fiber/epoxy face sheets in the 0^o/45^o/0^o/45^o orientation and 1/8^th inch Nomex honeycomb core. The panels were cut into 5-inch square test plates for mechanical testing. All testing was done on a fixture designed and fabricated by Pratt & Miller Engineering and installed on an Instron testing system at Cal Poly. The twist test was performed by supporting diagonal corners of the plate while simultaneously loading the opposite two corners at a crosshead rate of .06 in/min (ASTM 3044-94R11). Out of 10 panels tested, …

Artificial Alveolar-Capillary Membrane On A Microchip, Keith Male

Materials Engineering

A microfluidic device was synthesized out of polydimethyl siloxane (PDMS) to simulate the structure of the alveolar-capillary interface of the human lung. Soft lithography techniques were used to build a mold structure out of SU-8 epoxy at heights ranging from 30µm to 110 µm on a silicon substrate, with the 70 µm structure working the best. A mixture of 10:1 Sylgard 184 elastomer was then cast using the mold, and cured at a temperature of 80^oC. For the porous membrane, the PDMS was spun on at 6000rpm for 30 seconds using a spin coater to produce a membrane …

Bond Strength Characterization Of Su-8 To Su-8 For Fabricating Microchannels Of An Electrokinetic Microfluidic Pump, Nash Anderson

Materials Engineering

Photosensitive negative resist polymer layers of SU-8 2050 were adhered to 100 mm n-type silicon and Pyrex wafers via spin coating. These wafers were then bonded together at various temperatures of 100 ͦC, 120 ͦC, 140 ͦC, 150 ͦC, 160 ͦC, and 180 ͦC. The target thickness of each SU-8 layer was 100 µm. Photolithography was used to create microfluidic channels within the SU-8. An n-type silicon wafer and a Pyrex wafer, each with an SU-8 layer, were brought together on the “hard bake” or final step of SU-8 polymerization. A pressure of ~300 KPa was applied during the hard …

Multipolymer Interactions In Bulk Heterojunction Photovoltaic Devices, Grant Olson

Physics

Multipolymer photovoltaics, single layer devices made up of multiple photoactive polymers, can create organic photovoltaics (OPVs) with a wider spectral response than single polymer systems without the difficult fabrication of a tandem. Our group has successfully created multipolymer solar devices with 2% power conversion efficiency. We have analyzed the optical and electrical properties of these devices, and found that it may be possible for polymers to assist each other with charge extraction, though combining polymers disrupts single polymer crystallinity.

Effects Of Abrasive Particles On The Projected Fatigue Life Of Nylon Climbing Rope, Casey Johnson, Charlie Klonowski

Materials Engineering

When climbing rope is used outdoors, it is exposed to foreign particles such as sand and silt. These particles can potentially work their way through a rope’s sheath and damage the load bearing core decreasing the rope’s strength without exhibiting obvious wear. This project quantified the effect of abrasive particles on the fatigue life of nylon climbing rope. The experimental design involved 18 pieces of static nylon rope of kernmantle construction. 9 of these samples were heavy agitated in a slurry of water, silt, sand and soil, and left to sit for 24 hours. The remaining 9 samples were submerged …

Active Response Of Polymer Materials From External Stimuli – Solvents And Light; Grafting Reactions On Perovskite Layers, Jianxia Zhang

LSU New Orleans Theses and Dissertations

The active response of a series of polymeric materials was investigated. Both solvent activated and light activated thin films and wire systems show dynamic behaviors when exposed to different stimuli.

Solvent mediated fluxional behavior of polymer thin films involved extensive, rapid curling both on infusion and evaporation of good solvents. These films can be either lab-fabricated ones or commercial ones, and the curling behavior can be as fast as seconds. Conditions including polymer materials, chosen solvents, and film geometry can affect the behavior.

Methods that allowed for the creation and retention of distorted wire structures were also developed; the asymmetric …

Advanced Design Optimization For Composite Structure: Stress Reduction, Weight Decrease And Manufacturing Cost Savings, Shayan Ahmadian

Master's Theses

An injection moldable chopped fiber composite actuator with detailed drawing and tolerances was designed within one year. A vendor was selected and a quote for injection molding tooling cost for production was obtained and the first prototype was built in addition of six months. The risks are identified and material characterization tests are proposed.

The objective of this project was redesigning an aluminum made actuator with a continuous fiber composite for weight saving purposes. After searching the literature and consulting with experts in the field it was concluded that manufacturing costs associated with continuous fiber composite are 3 times as …

Nanocharacterization Of Porous Materials With Atomic Force Microscopy, Yasemin Kutes

Master's Theses

Scanning Probe Microscopy techniques have proven very useful in the investigation of porous nanostructured surfaces. Especially, Atomic Force Microscopy (AFM) has been widely used due to its compatibility with non-conducting surfaces. In particular, AFM often complements other techniques like scanning and transmission electron microscopy by providing quantitative surface information coupled with nanoscale spatial resolution. Its ability to operate in fluid is also important, as this allows researchers to mimic the physiological environment of biological materials and systems. In this work, two main types of porous materials are studied with AFM, including Phosphoric Acid Fuel Cell (PAFC) electrode catalyst layers, and …

Cross-Linked Pdms Expansion Due To Submersion In Liquid And Supercritical Co2, Teng Yang

Graduate Theses and Dissertations

Characterization of micro/nano-copper particles impregnated Polydimethylsiloxane (PDMS) submersed in supercritical carbon dioxide (scCO2) was studied. The purpose of this investigation was to advance micro-corrosion sensor technology utilizing PDMS and micro-metal particle composite as the sensing element currently under-development. One of the key challenges encountered was the removal of the native oxides inherently existing on the metal particles. Numerous techniques were experimented with to counter this problem at the UA Engineered Micro/Nano Systems Laboratory (EMNSL), with swell-based protocols being identified as the most promising solution. In terms of compatibility to Micro-electro-mechanical Systems (MEMS) fabrication, CO2 is often used in the release …

A Conductivity Testing System Coupled With A Tensile Testing Machine To Measure The Surface Properties Of Polymer Specimens, Nguyen T. Nguyen

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Polymers play an essential role in our everyday life due to their employment in a widespread range of applications. Polymers are used in industries such as space, biomedical, electronics, etc. in which their electrical and mechanical properties are major aspects which need to be investigated prior to implementation. When subjected to mechanical stimulations, polymers may exhibit changes in electrical conductivity which can vary locally within the specimens, especially in those of conducting polymers. In mechanical investigations a tensile testing machine is used to understand polymers’ strength, elasticity or other mechanical properties. In electrical analysis, using a four-point probe to examine …

Electrospun Polycaprolactone Nanofiber Scaffolds For Tissue Engineering, Andreas Haukas

Graduate Theses and Dissertations

Stem cell and tissue engineering offer us with a unique opportunity to research and develop new therapies for treating various diseases that are otherwise incurable using traditional medicines. However, development of these new therapies replies upon the establishment of in vitro cell culture and differentiation systems that mimic in vivo microenvironments required for cell-cell and cell-ECM interaction. The development of these cell culture systems depends upon the identification of appropriate biomaterials and cell sources. Biomaterials should be carefully selected and fabricated into scaffolds for supporting cell growth and differentiation. In this study, we explored the fabrication of 3D electrospun nanofiber …

Physiochemical And Nanomanipulation Studies Of Carbon Nanomaterials, Siva Naga Sandeep Chalamalasetty

Graduate Theses and Dissertations

Carbon nanomaterials are, without a doubt, one of man's wonder creations. Though these nanomaterials are a very recent trend, extraordinary electromechanical properties and the light weightiness of these nanomaterials attracted the attention of researchers. Although vast research has been done since the start of the US nanotechnology initiative, much effort was in the area of synthesis and characterization of the nanomaterials. However, most of the traditional macroscopic material's theories fail at the nanoscale level, and since the material properties are dependent on size and structure at nanoscale level, the behavior of the carbon nanomaterials in different environments needs attention. High …

The Implementation Of A Visco-Hyperelastic Numerical Material Model For Simulating The Behaviour Of Polymer Foam Materials, Conor Briody, Barry Duignan, Stephen Jerrams, John Tiernan

Articles

Polyurethane foam has been in use for some time in wheelchair seating systems as it offers good pressure relieving capabilities in most cases. However, little characterisation work has gone into seating foam materials by comparison with conventional elastomeric materials. Accurate material models could allow better prediction of foam in-service behaviour, which could potentially improve seating design practises. The objective of this work was to develop an approach for the validation of hyperelastic and viscoelastic material model parameters used to simulate polyurethane foam behaviour. Material parameters were identified from relevant test procedures and implemented in a Finite Element simulation of an …

Biomedical Properties And Preparation Of Iron Oxide-Dextran Nanostructures By Maple Technique, Carmen Steluta Ciobanu, Simona Liliana Iconaru, Eniko Gyorgy, Mihaela Radu, Marieta Costache, Anca Dinischiotu, Philippe Le Coustumer, Khalid Lafdi, Daniela Predoi

Chemical and Materials Engineering Faculty Publications

Background: In this work the chemical structure of dextran-iron oxide thin films was reported. The films were obtained by MAPLE technique from composite targets containing 10 wt. % dextran with 1 and 5 wt.% iron oxide nanoparticles (IONPs). The IONPs were synthesized by co-precipitation method. A KrF* excimer laser source (λ = 248 nm, τFWHM≅25 ns, ν = 10 Hz) was used for the growth of the hybrid, iron oxide NPs-dextran thin films.

Results: Dextran coated iron oxide nanoparticles thin films were indexed into the spinel cubic lattice with a lattice parameter of 8.36 Å. The particle sized calculated was …

Carbon Nanotubes Grown On Glass Fiber As A Strain Sensor For Real Time Structural Health Monitoring, Matthew Boehle, Qiong Jiang, Lingchuan Li, Alexandre Lagounov, Khalid Lafdi

Chemical and Materials Engineering Faculty Publications

In order to more effectively monitor the health of composite structures, a fuzzy fiber sensor has been developed. The fuzzy fiber is a bundle of glass fibers with carbon nanotubes or nanofibers (CNTs or CNFs) grown on the surface. The nanotube coating makes the fiber bundle conductive while the small conductive path increases sensitivity. The fuzzy fiber sensor can replace conventional metal foil strain gauges in composite applications. The electrical response of the sensor is monitored in real time to measure strain, vibration, cracking and delamination. Continuous monitoring provides instant notification of any problems. Implementation of this sensor network in …

The Significance Of Equi-Biaxial Bubble Inflation In Determining Elastomeric Fatigue Properties, Stephen Jerrams, Niall Murphy, John Hanley

Books/Book Chapters

It is well documented that for the effective modelling of the static and dynamic behaviour of elastomeric components using the finite element (FE) method it is essential to obtain material parameters that are derived from a range of physical tests. For a conventional linear solid, uniaxial testing suffices to fully characterise the material, but for rubber it is necessary to test in at least two deformation modes. Also, the determination of fatigue lives of rubber components is still in its infancy and a reliable, repeatable fatigue test for rubber will have important consequences for component design, functionality, maintenance and cost. …

Limited Thermal Conductance Of Metal-Carbon Interfaces, Jaime J. Gengler, Sergei V. Shenogin, John E. Bultman, Ajit K. Roy, Andrey A. Voevodin, Christopher Muratore

Chemical and Materials Engineering Faculty Publications

The thermal conductance for a series of metal-graphite interfaces has been experimentally measured with time-domain thermoreflectance (TDTR). For metals with Debye temperatures up to ∼400 K, a linear relationship exists with the thermal conductance values. For metals with Debye temperatures in excess of ∼400 K, the measured metal-graphite thermal conductance values remain constant near 60 MW m−2 K−1. Titanium showed slightly higher conductance than aluminum, despite the closeness of atomic mass and Debye temperature for the two metals. Surface analysis was used to identify the presence of titaniumcarbide at the interface in contrast to the aluminum and gold-carbon interfaces (with …