Polymer and Organic Materials Commons^™

Development And Tribological Characterization Of Uhmwpe-Tin Composite Coatings Deposited By Electrostatic Spraying, Jarrod Keith Perez

Theses and Dissertations

The increasing demand for inert, wear-resistant, cost-efficient, environmentally friendly, and low-friction coatings has driven extensive research into polymer-based solutions. Among these, ultra-high-molecular-weight polyethylene (UHMWPE) has emerged as a strong candidate due to its low density, anticorrosion properties, self-lubricating nature, affordability, and ease of processing. However, its low load-bearing capacity limits its widespread use in high-stress tribological applications. To overcome this limitation, this project investigates the development and characterization of UHMWPE composite coatings reinforced with titanium nitride (TiN) particles at varying concentrations (2.5, 5, and 10 wt%) to enhance their mechanical properties and wear resistance.

Molecular Modeling Methods And Applications For Accelerating Polymerization And Pyrolysis Studies, Joshua D. Kemppainen

Dissertations, Master's Theses and Master's Reports

Polymer matrix composites and carbon-carbon composites play critical roles in the aerospace, automotive, and construction industries. Different matrix materials and processing conditions can lead to a large variety of composite materials and composite properties. Integrated computational materials engineering has been used to tailor PMC matrix materials and processing conditions to specific properties and manufacturing techniques. The integrated computational materials engineering process modeling framework uses molecular dynamics at the nanometer length scale to characterize the evolving thermo-mechanical properties of the polymer as it cures. Then finite element analysis is used at the micrometer length scale to adjust cure cycles to tailor …

Spray-On Sensor Formulations That Enable Detection Of Physical And Chemical Stimuli, Priyanka Shiveshwarkar

Bioengineering Dissertations - Archive

Polydiacetylene based materials have been used for a variety of liquid phase sensing applications. There remains a need for low cost, easy-to-read gas phase sensors for continuous monitoring of physiological parameters and environmental hazards at work or at home. Such sensors could have applications in everyday life, for example as point-of-care or at home testing devices to enable early detection of disease to reduce healthcare costs. Making accessible and non-invasive technologies for monitoring of health and health risks provides individuals with the ability to be proactive in regard to their health and safety. In other examples, environmental monitoring systems could …

Characterization Of Interlayer Laser Shock Peening During Fused Filament Fabrication Of Polylactic Acid (Pla), Fabien Denise

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The field of additive manufacturing (AM) has gained a significant amount of popularity due to the increasing need for more sustainable manufacturing techniques and the adaptive development of complex product geometries. The problem is that AM parts routinely exhibit flaws or weaknesses that affect functionality or performance. Over the years, surface treatments have been developed to compensate certain flaws or weaknesses in manufactured products. Combining surface treatments with the modularity of additive manufacturing could lead to more adaptable and creative improvements of product functions in the future. The current work evaluates the feasibility of pursuing a new research axis in …

Effect Of Environmental And Ultraviolet Degradation On The Albedo Of Polyethylene Sheet Materials For Improved Energy Harvesting By Bifacial Photovoltaic Power Plants, William A. Jang, Roxy H. Jackson-Gain

Materials Engineering

Solar energy farms typically utilize monofacial photovoltaic (mPV) cells in their arrays to capture direct sunlight to produce renewable energy. However, the efficiency of these farms can be increased by 2 – 6% through the implementation of bifacial photovoltaic cells (bPV). These bPV cells function by capturing incident ultraviolet (UV) light energy that is reflected off the surface to increase its overall energy production. The amount of UV energy that is reflected is dependent on the albedo value of surface, which is a measure of energy reflectance. In this study, samples of unreinforced polyethylene (PE), scrim-reinforced polyethylene (SR-PE), and woven …

Beeswax Wraps As An Alternative To Single-Use Plastics, Sarah Skiver

Williams Honors College, Honors Research Projects

The project goal was to compare the food storage efficacy of sustainable beeswax wraps verses the single-use plastic methods of resealable plastic sandwich bags and plastic cling wrap. The goal was also to test the reusability of the beeswax wraps, as it is a key advantage of beeswax wraps that is advertised. The project purpose was to explore sustainable and eco-friendly alternatives to single use plastics, which are harmful to the environment in both their production and their disposal. Food spoilage was compared in beeswax wrap, plastic sandwich bags, and plastic cling wrap, and spoilage was also observed in a …

Characterization Of Thermal Gelation Properties In Bioresorbable Thermally Activated Hydrogel Polymers For Hernia Surgery Applications, Alexander Mayfield

All Theses

Hydrogel adhesives are a new class of materials with excellent biocompatibility, which makes them very attractive for biomaterial applications. It has been previously shown that Tetronic T1107, a four-arm poly (propylene oxide)-poly (ethylene oxide) (PPO-PEO) block copolymer, is useful as a chemical crosslinking thermo-responsive hydrogel for bioadhesive applications. The end groups of this polymer are modified with acrylate and N-hydroxysuccinimide (NHS) functional groups. The acrylate end group gives the polymer cohesive properties with long-range chemical crosslinking using dithiothreitol (DTT), while the NHS end group gives the polymer adhesive properties through bonding with amines found in organic tissue. It was found …

3d Printed Multicomponent Polymer Based Materials Via Hybrid Filaments: Fabrication And Characterization, Erik Antonio

All Dissertations

Additive manufacturing, also known as 3D printing, promises a manufacturing revolution for both industry and academic circles. One of the most widely used method of 3D printing is Fused Deposition Modeling (FDM) or Fused Filament Fabrication (FFF), which requires a thermoplastic filament to be directed towards a heating block and then deposited via extrusion layer by layer to produce a finished part. However, there are significant issues with this technology, mainly a limitation on the materials available for use and mechanical property deficiencies when compared to traditional manufacturing. These issues are brought about by the temperature limited nature of the …

Electromechanical Fatigue Properties Of Dielectric Elastomer Stretch Sensors Under Orthopaedic Loading Conditions, Andrea Karen Persons

Theses and Dissertations

Fatigue testing of stretch sensors often focuses on high amplitude, low-cycle fatigue (LCF) behavior; however, when used for orthopaedic, athletic, or ergonomic assessments, stretch sensors are subjected to low amplitude, high-cycle fatigue (HCF) conditions. As an added layer of complexity, the fatigue testing of stretch sensors is not only focused on the life of the material comprising the sensor, but also on the reliability of the signal produced during the extension and relaxation of the sensor. Research into the development of a smart sock that can be used to measure the range of motion (ROM) of the ankle joint during …

Prospects For Using Metal-Polymer Composite Structures In The Gear Manufacturing, Umid Mamasobirov, Shoraxmat Shoobidov, A F. Husanboyev

Technical science and innovation

In this paper, some thermoplastic polymer composites and filler composites for the production of metal-polymer gear transmissions are presented. Efforts have been made to expand the raw material base and identify ways to increase the durability of gears through technological and design measures.

Development Of Biomaterials For Drug Delivery, Raquel De Castro

Graduate Theses and Dissertations

Drug delivery systems (DDS) have highly evolved in the last decades with the development of hydrogels and nanoparticles. However, high systemic uptake, side effects, low bioavailability, and encapsulation efficiency continue to be a major hurdle faced by such DDSs.

Nanoparticles and hydrogels can be specifically designed for targeted DDSs to mitigate some of the problems. This dissertation aimed to design two DDSs for ocular drug delivery and one for cancer treatment. The first project sought to develop chitosan nanoparticles (Cs-NP) using PEGDA as a copolymer to encapsulate gentamicin (GtS) for ocular drug delivery. Cs-NPs contain positive charges that can interact …

Multi-Level Analysis Of Atomic Layer Deposition Barrier Coatings On Additively Manufactured Plastics For High Vacuum Applications, Nupur Bihari

Dissertations, Master's Theses and Master's Reports

While hardware innovations in micro/nano electronics and photonics are heavily patented, the rise of the open-source movement has significantly shifted focus to the importance of obtaining low-cost, functional and easily modifiable research equipment. This thesis provides a foundation of open source development of equipment to aid in the micro/nano electronics and photonics fields.

First, the massive acceptance of the open source Arduino microcontroller has aided in the development of control systems with a wide variety of uses. Here it is used for the development of an open-source dual axis gimbal system. This system is used to characterize optoelectronic properties of …

Effects Of Hard-To-Soft Segment Ratios On The Synthesis And Physico-Mechanical Properties Of Polyurethane Films, Aaron C. Wilson

Mechanical Engineering Theses

Blood-contacting cardiovascular stents often induce a secondary clotting event due to unrestricted enzymatic activities. The use of hemocompatible polyurethane coatings on these implantable devices is one of the most promising methods to reduce device rejection. In this study, four commercial polyurethane films of various thicknesses and compositions were evaluated for their anticoagulation properties. Results suggested that these films exhibited excellent thermal and physico-mechanical properties while capable of increasing contact time with blood plasma by over a thousand-fold as compared to a control surface. Due to the unknown structure and composition of these commercial films, polyurethane samples were synthesized from toluene …

Tailoring Photodegradation Rates Of Acetal-Containing Polymer Networks, Michael Sandoz

Honors Theses

In this thesis, we explore the degradation of poly (thioether acetal) thermosets via a photoinduced thiol-catalyzed ß-scission of acetal linkages incorporated as network crosslink junctions. Specifically, a library of bis-allyl acetal-containing monomers derived from para-substituted benzaldehydes was synthesized and formulated into photopolymerizable thiol-ene resins with commercially available thiol monomers. By varying the electron donating or withdrawing nature of the monomer substituent, we explored the impact of substituent effects on the rate of polymer degradation. Furthermore, we compare the results to those expected from a classical Hammett-type relationship of substituent electronic effects. FTIR was employed to track the appearance of the …

Towards Completely Automated Glycan Synthesis, Matteo Panza

Dissertations

Carbohydrates are ubiquitous both in nature as biologically active compounds and in medicine as pharmaceuticals. Although there has been continued interest in the synthesis of carbohydrates, chemical methods require specialized knowledge and hence remain cumbersome. The need for development of rapid, efficient and operationally simple procedures has come to the fore. This dissertation focuses on the development of a fully automated platform that will enable both experts and non-specialists to perform the synthesis of glycans. Existing automated methods for the synthesis of oligosaccharides are highly sophisticated, operationally complex, and require significant user know-how. By contrast, high performance liquid chromatography (HPLC) …

Minimizing The Dimensional Change In Two Component Epoxy Based Thermoset Adhesives Through Adapting Mix Ratio And Initial Crosslink Density, Jefferson Peter Norman

Materials Engineering

Meissner Filtration uses amine-hardened epoxy as a high-performance adhesive to encapsulate hollow fiber membranes at the ends of rigid filter housings. Dimensional change of the epoxy while curing can result in residual stress formation that is detrimental to the manufacturing of the filter and causes structural integrity issues when the filter is used in industrial processes where heating and cooling cycles are implemented. The residual stresses can cause cracks, microscopic fractures, and delamination from the housing, resulting in failure of the filter. The goal of this project was to evaluate how changes in processing conditions could minimize dimensional variability due …

Non-Toxic Soil Thickeners For Reducing Mudslide Intensity, Miranda Miao, Isaac Blackburn, Erika Haley Yao

Materials Engineering

Non-toxic food thickeners were investigated as a solution for thickening mud to mitigate the effects of mudslides. All soil was obtained from a site on the California Polytechnic State University campus where a mudslide occurred in 2017. Guar gum was mixed into the soil at 1 wt% and 10 wt% of the moisture content in the soil. Whey protein was mixed into the soil at 2 wt% and 19 wt% of the moisture content in the soil. The soils’ liquid limit was found using the Casagrande cup testing method. Liquid limit testing indicated that thickeners raised the liquid limit, most …

Maximizing Poly(3-Butylthiophene-2,5-Diyl) Electrical Conductivity By Maximizing Transcrystal Growth, Edward Alexander Bicknell

Materials Engineering

Polymers are generally considered electrical insulators. Despite this, research in the mid 1970’s found that polymers consisting of a conjugated backbone structure could become electrically conductive upon doping.1 The conjugated polymer analyzed for this project was poly(3-butylthiophene-2,5-diyl) (P3BT). Transcrystals have been found as a way to promote electrical conductivity through mechanisms including π bond atomic orbital overlap and electron mobility.2 In theory, maximizing transcrystal length would also maximize P3BT electrical conductivity, increasing its applicable use in electronic devices. The goal of this project was to determine a methodological way to maximize P3BT electrical conductivity by producing the longest transcrystal length …

Compression Set Improvement Of Thermoplastic Vulcanizates For High Temperature Tubing, Mitchell Valaitis

Williams Honors College, Honors Research Projects

It was hypothesized that increasing the curative level of the fluorocarbon rubber (FKM) used in manufacturing of thermoplastic vulcanizate (TPV) materials would decrease the compression set values of the TPV enough for it to be suitable as a flexible, lightweight alternative to high operating temperature thermoset rubber tubing currently being used for power steering hose. First, promising TPV formulations were identified by varying the polyamide (PA) and FKM used in a Brabender mixer. Four different types of polyamide and four different types of FKM were investigated, with two of the FKM types and one polyamide type identified as being promising. …

Magnetic Ordering In A Vanadium-Organic Coordination Polymer Using A Pyrrolo[2,3-D:5,4-D']Bis(Thiazole)-Based Ligand, Yulia A. Getmanenko, Christopher S. Mullins, Vladimir N. Nesterov, Stephanie Lake, Chad Risko, Ezekiel Johnston-Halperin

Chemistry Faculty Publications

Here we present the synthesis and characterization of a hybrid vanadium-organic coordination polymer with robust magnetic order, a Curie temperature T_C of ∼110 K, a coercive field of ∼5 Oe at 5 K, and a maximum mass magnetization of about half that of the benchmark ferrimagnetic vanadium(tetracyanoethylene)_~2 (V·(TCNE)_~2). This material was prepared using a new tetracyano-substituted quinoidal organic small molecule 7 based on a tricyclic heterocycle 4-hexyl-4H-pyrrolo[2,3-d:5,4-d′]bis(thiazole) (C₆-PBTz). Single crystal X-ray diffraction of the 2,6-diiodo derivative of the parent C₆-PBTz, showed a disordered hexyl chain and …

Exploring The Relationship Between Cellular Structure And Mechanical Properties Of Polymer Foams, Timothy Lee Tan

Materials Engineering

Polymer foams are the material of choice for applications that require comfort, cushioning, and high energy absorption. While popular, the relationship between their microstructure and their mechanical properties is not yet strongly predictable. The aim of this project is to look at the different relationships between the area or volume occupied by pores compared to the amount of solid material and determine which method of quantifying this relationship will provide the best prediction of mechanical properties. To examine this relationship, foams of various densities made from either ethylene-co-vinyl acetate or thermoplastic polyurethane were first physically characterized through three methods: (1) …

Improving The Mechanical Performance Of 3d Printed Parts Using Fused Filament Fabrication, Inderpreet Binning

Industrial and Manufacturing Engineering

The 3D printing industry has seen rapid growth in the last 10 years and has been called the next industrial revolution. There are several different processes used in 3D printing, but the most popular process is called Fused Filament Fabrication (FFF) or Fused Deposition Modeling (FDM). This is the process where (most commonly) plastic filament enters a nozzle, is heated to a semi-liquid state, and then deposited into a pattern to create a print. One major drawback to this process is that the prints are anisotropic. This means that the strength of the print varies with the orientation that it …

Synthesis Of Acceptors For Use In Donor-Acceptor Copolymers And Characterization Of These Polymers, William D. Walker

Honors Theses

In this thesis, a selenium-derivatized acceptor was synthesized to examine the heavy atom effects of selenium on the position of the frontier molecular orbitals (HOMO/LUMO band gap) as opposed to sulfur in a donor-acceptor copolymer for use in light harvesting and detection applications. Over the course of this research, standard operating protocols for ultraviolet-visible (UV-Vis-NIR) and Fourier transform infrared (FT-IR) spectroscopies, as well as cyclic voltammetry (CV) characterization techniques were established. Once synthesized, the polymers were characterized through use of the established characterization protocols. The selenium-derivatized polymer exhibited a bathochromic shift compared to the sulfur analogue, with a solid-state absorption …

Thermal And Mechanical Properties Of Polymers Using Molecular Dynamics, Daniel Glass, Alejandro Strachan, Lorena Alzate-Vargas, Chunyu Li, Benjamin Haley

The Summer Undergraduate Research Fellowship (SURF) Symposium

Polymer systems have gained attention during the past years because of their technological and industrial applications. Simulations, particularly molecular dynamics, are very useful for exploring properties of amorphous polymers, without using experiments. Our goal is to create a readily-available tool that will perform MD simulations in order to get thermal and mechanical properties (Glass transition temperature, Young Modulus) of the polymers. The work that has been done will be part of a tool to help people to learn about polymer properties including Glass Transition Temperature. We model some polymers at a scale of 10,000 atoms. The tool uses LAMMPS to …

Electrospinning Of Polycaprolactone Core-Shell Nanofibers With Anti-Cancer Drug, Sakib Iqbal, Mujibur Khan, Saheem Absar, Andrew Diamanduros, Samuel Chambers

GS4 Student Scholars Symposium

Encapsulation of a model anti-cancer drug, 5-Fluorouracul (5-FU) into biocompatible core-shell nanofibers of polycaprolactone (PCL) nanofibers was fabricated using a coaxial electrospinning process. Our work aims to solve these issues using a novel method of fabrication of fibers featuring confinement of drugs within a biodegradable core-shell structure, thereby permitting sustained release of drugs to specific sites of treatment, such as tissues affected with tumor cells. The coaxial electrospinning was performed using a sheath polymer solution consisting of a 14 wt% PCL solution and a 5 wt% solution of 5-FU as the core solution. Dimethylformamide (DMF) was used as the solvent …

Design And Synthesis Of Low-Bandgap Polymers For Organic Photovoltaic Applications, Letian Dou

Link Foundation Energy Fellowship Reports

This research at UCLA focused on the design and synthesis of novel conjugated polymers as the electron-donor material for photovoltaic devices. By careful molecular design both on the polymer backbone and the side chains, a series of low-bandgap conjugated polymers were synthesized for a variety of photovoltaic applications, including single junction and tandem polymer solar cells. In addition, the author designed and synthesized a novel higly perfect polymer single crystal material via a visible light triggered topochemical reaction. This kind of materials shows high potential for application in solar cells and transistors, which, the author believe, is a huge breakthrough …

Evaporation-Induced Formation Of Well-Ordered Surface Patterns On Polymer Films, Wei Sun

Theses and Dissertations--Chemical and Materials Engineering

Various techniques of fabricating surface patterns of small scales have been widely studied due to the potential applications of surface patterns in a variety of areas. It is a challenge to fabricate well-ordered surface area efficiently and economically. Evaporation-induced surface patterning is a promising approach to fabricate well-ordered surface patterns over a large area at low cost. In this study, the evaporation-induced surface patterns with controllable geometrical characteristics have been constructed. The dewetting kinetics on deformable substrate is also investigated.

Using simple templates to control the geometry and the evaporation behavior of a droplet of volatile solvent, various gradient surface …

Wear Resistant Polydopamine/Ptfe Nanoparticle Composite Coating For Dry Lubrication Applications, Samuel George Beckford

Graduate Theses and Dissertations

This dissertation presents an investigation into the effect of nanoparticle fillers and a polydopamine adhesive primer on the tribological performance of thin PTFE films. The principal objective of this investigation was to reduce wear in PTFE films, an issue which precludes the use of PTFE films in tribological applications requiring high durability. The friction and wear of the composite films were evaluated using a ball-on-flat configuration in linear reciprocating motion. It was found that the use of a polydopamine adhesive primer reduces the wear of PTFE films more than 600 times. X-ray photoelectron spectroscopy (XPS) results show that a tenacious …

Rheo-Piv Investigation Of Fracture And Self-Healing In A Triblock Copolymer Gel, Benjamin A. Helfrecht, Travis L. Thornell, Kendra A. Erk

The Summer Undergraduate Research Fellowship (SURF) Symposium

Physically associating polymer gels have shown the ability to heal after failure, making them promising candidates for various medical applications or consumer products. However, the processes by which these materials self-heal is not well-understood. This study seeks to explain the self-healing behavior of the triblock copolymer poly(methyl methacrylate)-poly(n-butyl acrylate)-poly(methyl methacrylate), or PMMA-PnBA-PMMA, by probing the material’s post-fracture behavior with rheometry and particle image velocimetry (PIV). The self-healing behavior was studied by deforming each gel in shear until failure multiple times with “recovery” periods in-between. PIV was used to verify the occurrence of each fracture in both time and space. Stress …

A Soft Condensed Matter Approach Towards Mathematical Modelling Of Mass Transport And Swelling In Food Grains, Michael Chapwanya, N. Misra

Articles

Soft condensed matter (SCM) physics has recently gained importance for a large class of engineering materials. The treatment of food materials from a soft matter perspective, however, is only at the surface and is gaining importance for understanding the complex phenomena and structure of foods. In this work, we present a theoretical treatment of navy beans from a SCM perspective to describe the hydration kinetics. We solve the transport equations within a porous matrix and employ the Flory–Huggin’s equation for polymer–solvent mixture to balance the osmotic pressure. The swelling of the legume seed is modelled as a moving boundary with …