Semiconductor and Optical Materials Commons^™

Characterization Of Metal Contacts On Hydrothermally Synthesized Uranium Dioxide For Novel Semiconductor Applications, Tory E. Robinson

Theses and Dissertations

This research is focused on determining which metals or combinations of metals form effective electrical contacts on hydrothermally synthesized UO2 substrates to allow for additional work in characterization of the material as well as the feasibility of its use in semiconductor devices such as solid-state neutron detectors. A methodology was established for selection of candidate metals. Target mixtures composed of Au, Ag, Pt, and Mg were chosen along with several single-metals. Thin metal films were deposited onto tungsten probe tips and hydrothermally synthesized UO2 samples to allow for analysis of mechanical and deposited contact to the substrates through I-V measurements.

3-D Multifunctional Sensors Fabricated On Fiber Tips Using A Two-Photon Polymerization Process, Jonathan W. Smith

Theses and Dissertations

This thesis conducts research involving designing, fabricating, and testing optical fiber tip refractive index sensors. The fabrication process used for these sensors is a two-photon polymerization process utilizing a photo sensitive polymer. Unlike planar lithography, this fabrication process allows the creation of arbitrary shapes with a great degree of freedom. Three different fiber tip sensors were fabricated and tested. The first is a flat surfaced single cavity Fabry-Pérot interferometer (FPI) device, the second is a flat surfaced double cavity FPI device, and the final is a confocal surfaced double cavity FPI device. These sensors are tested for thermal radiation and …

Coupling Of Light's Orbital Angular Momentum To A Quantum Dot Ensemble, Alaa A. Bahamran

Electronic Theses and Dissertations

We theoretically and experimentally investigate the transfer of orbital angular momentum from light to an ensemble of semiconductor-based nanostructures composed of lead sulfide quantum dots. Using an ensemble of quantum dots offers a higher cross-section and more absorption of twisted light fields compared to experimentally challenging single-nanostructure measurements. However, each quantum dot (except for on-center) sees a displaced light beam parallel to its own axis of symmetry. The transition matrix elements for the light-matter interaction are calculated by expressing the displaced light beam in terms of the appropriate light field centered on the nanoparticles. The resulting transition rate induced by …

Scanning Probe Microscopy Measurements On 2d Materials And Iridates, Armin Ansary

Theses and Dissertations--Physics and Astronomy

In the past two decades, there has been a quest to understand and utilize novel materials such as iridates and two-dimensional (2D) materials. These classes of materials show a lot of interesting properties both in theoretical predictions as well as experimental results. Physical properties of some of these materials have been investigated using scanning probe measurements, along with other techniques.

One-dimensional (1D) catalytic etching was investigated in few-layer hexagonal boron nitride (hBN) films. Etching of hBN was shown to share several similarities with that of graphitic films. As in graphitic films, etch tracks in hBN commenced at film edges and …

Engineering Plasmonic Nanostructures For Light Management And Sensing, Sujan Phani Kumar Kasani

Graduate Theses, Dissertations, and Problem Reports (ETD)

The two major global problems are to provide health safety and to meet energy demands for ever growing population on a large scale. The study of light interaction with nanostructures has shown a promising solution in improving the fields of bio-sensor and solar energy devices which addresses above mentioned two major global problems. Nanostructures have tunable physicochemical properties such as light absorption, electrical and thermal properties unlike bulk materials, which gives an advantage in applications like bio-sensing and energy harvesting devices. The development of nanofabrication techniques along with the discovery of Surface Enhanced Raman Scattering (SERS) and Plasmon Enhanced Fluorescence …

Transient Transmission Oscillations In Doped And Undoped Lithium Niobate Induced By Near-Infrared Femtosecond Pulses, Bryan J. Crossman, Gregory J. Taft

Physics Faculty Publications

Transient transmission oscillations in X-cut and Z-cut congruent, iron-doped, and magnesium-doped lithium niobate samples were measured using 50 fs, 800 nm, 0.5 nJ pulses from a self-mode-locked Ti:sapphire laser in an optical pump–probe system. Several Raman-active oscillation modes excited by these pulses were observed as changes in the transmitted probe intensity versus time delay between the pump and probe pulses. The samples were rotated to determine how the incident polarization of the pump pulses affects the mode excitations. The observed Raman-active oscillations correspond to previously reported symmetry modes measured with traditional, continuous-wave, Raman spectroscopy using the same scattering …

A Simple And Robust Approach To Reducing Contact Resistance In Organic Transistors, Zachary A. Lamport, Katrina J. Barth, Hyunsu Lee, Eliot Gann, Sebastian Engmann, Hu Chen, Martin Guthold, Iain Mcculloch, John E. Anthony, Lee J. Richter, Dean M. Delongchamp, Oana D. Jurchescu

Chemistry Faculty Publications

Efficient injection of charge carriers from the contacts into the semiconductor layer is crucial for achieving high-performance organic devices. The potential drop necessary to accomplish this process yields a resistance associated with the contacts, namely the contact resistance. A large contact resistance can limit the operation of devices and even lead to inaccuracies in the extraction of the device parameters. Here, we demonstrate a simple and efficient strategy for reducing the contact resistance in organic thin-film transistors by more than an order of magnitude by creating high work function domains at the surface of the injecting electrodes to promote channels …

Growth And Behaviors Of Inn/Gan Multiple Quantum Wells By Plasma-Assisted Molecular Beam Epitaxy, Chen Li

Graduate Theses and Dissertations

Fully realizing the potential of InGaN semiconductors requires high quality materials with arbitrary In-content. To this date the growth of In-rich InGaN films is still challenging since it suffers from the low growth temperatures and many detrimental alloying problems. InN/GaN multiple quantum wells (MQWs) and super lattices (SLs) are expected to be promising alternatives to random InGaN alloys since in principle they can achieve the equivalent band gap of InGaN random alloys with arbitrarily high In-content and at the same time bypass many growth difficulties.

This dissertation focuses on studying the growth mechanisms, structural properties and energy structures of InN/GaN …

Fabrication And Characterization Of Electrochemical Glucose Sensors, Mohammed Marie

Graduate Theses and Dissertations

Electrochemical sensors based on the nanostructure of the semiconductor materials are of tremendous interest to be utilized for glucose monitoring. The sensors, based on the nanostructure of the semiconductor materials, are the third generations of the glucose sensors that are fast, sensitive, and cost-effect for glucose monitoring.

Glucose sensors based on pure zinc oxide nanorods (NRs) grown on different substrates, such ITO, FTO, and Si/SiO2/Au, were investigated in this research. Silicon nanowire (NW)- based glucose sensors were also studied. First, an enzyme-based glucose sensor was fabricated out of glass/ITO/ZnO NRs/BSA/GOx/nafion membrane. The sensor was tested amperometrically at different glucose concentrations. …

Comparative Study Of Power Semiconductor Devices In A Multilevel Cascaded H-Bridge Inverter, Kenneth Mordi

Graduate Theses and Dissertations

This thesis compares the performance of a nine-level transformerless cascaded H-bridge (CHB) inverter with integrated battery energy storage system (BESS) using SiC power MOSFETs and Si IGBTs. Two crucial performance drivers for inverter applications are power loss and efficiency. Both of these are investigated in this thesis. Power devices with similar voltage and current ratings are used in the same inverter topology, and the performance of each device is analyzed with respect to switching frequency and operating temperature. The loss measurements and characteristics within the inverter are discussed. The Saber® simulation software was used for the comparisons. The power MOSFET …

Growth And Characterization Of Silicon-Germanium-Tin Semiconductors For Future Nanophotonics Devices, Bader Saad Alharthi

Graduate Theses and Dissertations

The bright future of silicon (Si) photonics has attracted research interest worldwide. The ultimate goal of this growing field is to develop a group IV based Si foundries that integrate Si-photonics with the current complementary metal–oxide–semiconductor (CMOS) on a single chip for mid-infrared optoelectronics and high speed devices. Even though group IV was used in light detection, such as photoconductors, it is still cannot compete with III-V semiconductors for light generation. This is because most of the group IV elements, such as Si and germanium (Ge), are indirect bandgap materials. Nevertheless, Ge and Si attracted industry attention because they are …

Water Processable N-Type Organic Semiconductor, Ruben S. Riquelme, Matthew Collins Weisenberger, Camila F. Gomez

Center for Applied Energy Research Faculty Patents

The present invention concerns a water-processable n-type semiconductor comprised of polyvinylpyrrolidone (PVP), carbon nanotubes (CNTs) and poly(ethyleneimine) (PEI). The semiconductors are prepared by providing PVP and CNTs in a hydrophilic slurry and dispersing therein small amounts of PEI.

Vertical Transport Study Of Iii-V Type-Ii Superlattices, Zahra Taghipour

Optical Science and Engineering ETDs

Type-II strained layer superlattice (T2SL) semiconductors hold great promise for mid- and long-wavelength infrared photodetectors. While T2SL-based materials have advanced significantly in the last three decades, an outstanding challenge to improve the T2SLs is to understand the carrier transport and its limitations, in particular along the superlattice growth layers.

In this dissertation, an overview of the current state-of-the-art InAs/GaSb T2SLs is presented. Fundamental semiconductor device equations and transport properties, including miniband conduction and the drift-diffusion parameters, are reviewed, and the fundamental limiting factors in carrier's transport are discussed. Furthermore, the standard method of electron-beam-induced current technique to measuring these parameters …

Creating A Computational Tool To Simulate Vibration Control For Piezoelectric Devices, Ahmet Ozkan Ozer, Emma J. Moore

Posters-at-the-Capitol

Piezoelectric materials have the unique ability to convert electrical energy to mechanical vibrations and vice versa. This project takes a stab to develop a reliable computational tool to simulate the vibration control of a novel “partial differential equation” model for a piezoelectric device, which is designed by integrating electric conducting piezoelectric layers constraining a viscoelastic layer to provide an active and lightweight intelligent structure. Controlling unwanted vibrations on piezoelectric devices (or harvesting energy from ambient vibrations) through piezoelectric layers has been the major focus in cutting-edge engineering applications such as ultrasonic welders and inchworms. The corresponding mathematical models for piezoelectric …

Controlled Nanomorphology Of Hybrid Organic/Inorganic Multi-Component Composites Through Cooperative Non-Covalent Interactions, Lingyao Meng

Shared Knowledge Conference

Hybrid organic–inorganic nanocomposite polymers, with inorganic nanoparticles embedded in organic matrix have emerged as a special category of multifunctional materials. With rational materials design, these hybrids can show the synergistic effect of the properties from both phases. Homogenous dispersion and orderly arrangement of the organic and inorganic components are key in their functionalities. By controlling the interface and corresponding interfacial interactions between the organic and inorganic entities, we have developed a logical approach to form stable and controlled hybrid nanofiber structures. We demonstrate the formation of hybrid polymer/quantum dots (or iron oxide nanoparticles) nanocomposites through non-covalent interactions (hydrogen bonding, ionic …

The Fabrication And Characterization Of Cu(In,Ga)Se2 Solar Cell, Yasir Al-Rikabi

Theses and Dissertations

The extremely large energy consumption rate on Earth today is likely to exhaust the conventional energy resources such as fossil fuels and coal in the near future. The need for new renewable energy sources becomes inevitable and urgent. Among various new energy resources, solar energy is the most promising one because it is abundant and environmentally clean. The Sun light can be converted into electricity by using solar cell devices. Even though the solar cell panels made of thin films are in competition with conventional single crystal solar cells, only four thin film solar cells, i.e. amorphous silicon (a- Si), …

High Performance Glad Nanorod Cuinxga(1-X)Se2 Arrays With Enhanced Carrier Collection And Light Trapping For Photodetector Applications, Matthew P. Brozak

Theses and Dissertations

Nanostructured arrays have become an appealing alternative to their thin film and bulk counterparts in photovoltaic and photoconductivity applications. Thin films have recently continued the evolution of efficiency and material sciences after taking over from traditional, doped silicon devices. Inside of the thin film revolution, CuInxGa(1-x)Se2 (CIGS) has emerged as a high efficiency p-type semiconductor with a wide band gap that is tunable based on the Indium to Gallium ratio and often deposited via expensive, high temperature deposition methods. While each of the aforementioned methods of construction have their disadvantages, the advantages of each can be combined to potentially increase …

Nanoflower-Like Bi2moo6/Ag3po4 In Water Treatment, Xavier Morgan-Lange, Jaeyun Moon, Kaleab Ayalew

McNair Poster Presentations

• Environmental issues continue to intensify causing natural resources such as clean water to become increasingly scarce while demand only continues to grow. • Some of the most effective measures taken appear to be bioremediation tactics and their synthetic counterparts. • A critical area of interest are semi-conducting photocatalytic nanomaterials that take advantage of the photo-electric effect and use the introduction of ultra violet (UV) and visible light to induce oxidation and reduction reaction in p-type semiconductors. This results in the decomposition of certain pollutants and/or deactivates certain microbes in water. • These materials have the potential to operate using …

Electron Paramagnetic Resonance And Optical Absorption Study Of Acceptors In Cdsip2 Crystals, Elizabeth M. Scherrer, Larry E. Halliburton, Eric M. Golden, Kevin T. Zawilski, Peter G. Schunemann, F. Kenneth Hopkins, Kent L. Averett, Nancy C. Giles

Faculty Publications

Cadmium silicon diphosphide (CdSiP₂) is a nonlinear material often used in optical parametric oscillators (OPOs) to produce tunable laser output in the mid-infrared. Absorption bands associated with donors and acceptors may overlap the pump wavelength and adversely affect the performance of these OPOs. In the present investigation, electron paramagnetic resonance (EPR) is used to identify two unintentionally present acceptors in large CdSiP₂ crystals. These are an intrinsic silicon-on-phosphorus antisite and a copper impurity substituting for cadmium. When exposed to 633 µm laser light at temperatures near or below 80 K, they convert to their neutral paramagnetic charge …

Thienoisatin Oligomers As N-Type Molecular Semiconductors, Natalie M. Kadlubowski, Xuyi Luo, Jianguo Mei

The Summer Undergraduate Research Fellowship (SURF) Symposium

Organic field effect transistors (OFETs) offer many advantages compared to traditional inorganic transistors, such as flexibility and solution processability. In this study we design and synthesize two thienoisatin-based organic semiconducting small molecules, then investigate their electronic properties in n-type OFETs. To introduce n-type charge transport, electron-withdrawing dicarbonitrile moieties were installed on thienoisoindigo and bis-thienoisatin molecules, which led to a quinoidal conjugation on thienoisoindigo, while maintaining an aromatic conjugation on the bis-thienoisatin. Following the syntheses, the molecules were characterized to determine highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) levels via cyclic voltammetry, as well as any potential …

Application Of Nano-Plasmonics For Sers Bio-Detection And Photocatalysis In The Same Platform, Muhammad R. Shattique

Graduate Theses/Dissertations

Nano-biological systems interfacing nano-structured solid surfaces with biological compounds such as oligonucleotides or proteins are highly regarded as enabling materials for biosensing and biocatalysis applications. In particular, nanostructures of noble metals such as gold or silver, when exposed to light, exhibit a phenomenon known as surface plasmon resonance. When a proper metal nanostructure (plasmonic substrate) is exposed to light, very efficient absorption of incoming photons is possible, resulting in a buildup of localized high-energy regions, or “hot-spots”, where energetic carriers or “hot carriers” can be created. These hot-carriers can be used to catalyze desired chemical transformations in materials located nearby. …

Properties Of Matter, Mike Jackson, Holly Haney

High School Lesson Plans

Students will investigate the relationship(s) between thermal and electrical properties of matter. First, students will use a multimeter and temperature probe to investigate the relationship between electrical resistance and temperature of an electrical resistor composed of metals. They will then graph collected data to analyze the relationship and draw a conclusion as to their relationship. They will then perform the same investigation on a thermal resistor made of a semiconducting substance and analyze that collected data. Finally, using ClaimEvidence-Reasoning (CER) structure, students will use their experimental evidence to state the similarities and differences between the electro-thermal properties of metals and …

Enhanced Coupling Strength Gratings For Outcouplers In Optical Waveguides, Ruo-Hua He

Electrical Engineering Theses and Dissertations

Gratings used for silicon photonic waveguides were demonstrated with outcoupling efficiency greater than 60% in a short grating length of 13 µm at a wavelength of 1550 nm. Due to problems of generating light from silicon, light has to be generated by either growing III-V material, wafer bonding III-V material to silicon, or externally generated light has to be coupled into and out of silicon photonic waveguides. Gratings have been used in semiconductor lasers to obtain single frequency operation. Some applications such as telecommunications require a narrow and single spectral line. And such single frequency lasers are typically distributed Bragg …

Modeling Recombination In Solar Cells, Paul Chery

Macalester Journal of Physics and Astronomy

Solar cells are a competitive alternative to nonrenewable energy sources such as fossil fuels. However, the efficiency of these devices is limited by photogenerated carrier recombination. We use a finite difference numerical model to study recombination phenomena in the absorber layer of solar cells including alternate recombination models and the effects of spatial distribution of recombination centers. We compare the effect of using the constant lifetime approximation for recombination to the full Shockley-Read-Hall expression in Silicon solar cells and find that the constant lifetime approximation holds for high defect densities but not for high photon flux densities. Finally, we simulate …

In Situ Sem Solidification Study Of Ga And Egain: A Characterization Technique For Monitoring The Microstructural Evolution Of Liquid Metals, Jeremy Geovann Del Aguila

Materials Engineering

Scanning electron microscopy (SEM) video recording is used to characterize the solidification of small volumes of 99.999% pure gallium (Ga) and eutectic gallium-indium (eGaIn) under a high vacuum environment. Specimen are superheated to 55℃ using a hot plate, cast into spherical droplets, and cooled in situ by means of a Peltier cooling stage. Special attention is given to the preparation of the specimen prior to viewing because of gallium and its alloys’ nature to form an oxide layer when melted and air cooled. The oxide acts as a skin that inhibits the observation of microstructural features during solidification. Heated samples …

Solar Cell Potential Induced Degradation Sensor, Luc Alexandre Tousignant

Materials Engineering

It is important to maintain Photovoltaic (PV) cells and protect them from damage mechanisms like Potential Induced Degradation (PID), which can contribute to shorter lifespans and lower efficiencies. Current leakage through cell encapsulation can cause charge migration in PV cells that reduces the maximum quantum efficiency, which is the cause of PID. An experiment was setup to determine the feasibility of a non-silicon sensor able to produce similar leakage behavior to traditional PV cells under recorded humidity conditions. Thin sheet metals were encapsulated in EVA, a common PV encapsulant polymer, and mounted in aluminum framing. Three sensors, along with a …

Three Speed 3d Printed Magnetic Gear, Robert J. Rutherford

Maseeh Summer Undergraduate Research Experience

Power transmission is traditionally achieved with a mechanical gear. Mechanical gears require maintenance, cause vibration, and have no overload protection. Magnetic gears offer an innovative solution to these drawbacks as they do not require regular maintenance, have no need for lubrication, create very little acoustic noise, have built in overload protection and as a result of these advantages, have a longer lifetime of operation. This research focused upon the design, assembly and demonstration of the magnetic gear concept. The research used a solid works design, 3D printed ABS plastic housing, and use of neodymium magnets and ferromagnetic iron segments.

This …

A Comparative Analysis Of Integrated Optical Waveguide Isolators With Magneto-Optic Layers, Reyhane Oztekin

Electrical Engineering Theses and Dissertations

The objective of this study is to theoretically devise an on-chip optical isolator which is monolithically integrated with a semiconductor waveguide layer yielding low loss. The optical properties of iron are modeled for the use of optical waveguide isolators by improving the Brendel-Bormann model. Our model for iron shows excellent fit with the optical data up to 30 electronvolts (eV). The semiconductor optical waveguide isolator with magneto-optic layers based on non-reciprocal loss shift is developed in this study. Fe, Co, and Ni metals as well as cerium-substituted yttrium iron garnet (Ce:YIG) have been used as magneto-optic layers. We have shown …

Investigation Of The Effects Of Harmful Radiation On Type-Ii Strained Layer Superlattice Focal Plane Arrays Operated In The Long Wave Infrared, Patrick Fumo

Electrical Engineering Theses and Dissertations

In-situ exposure of InAs/InAsSb strained layer superlattice focal plane arrays to gamma-rays revealed the possibility of a detector capable of imaging through a total ionizing dose event. Two long wave infrared focal plane arrays were exposed to a Co⁶⁰ source at dose rates of 60 Rads/s and 70 Rads/s in incremental steps up to a total accumulated dose of 30 kRads. The first device showed no degradation in dark current density with accumulated dose while the second device tested showed a small increase up to 1 kRad and minimal increases with subsequent dose steps. The primary imaging defect in …

Ii-Vi Semiconductor Nanowire Array Sensors Based On Piezotronic, Piezo-Phototronic And Piezo-Photo-Magnetotronic Effects, Shuke Yan

LSU New Orleans Theses and Dissertations

With the rapid progress of nanotechnologies, there are two developing trends for the next generation of sensors: miniaturization and multi-functionality. Device miniaturization requires less power consumption, or even self-powered system. Multi-functional devices are usually based on multi-property coupling effects. Piezoelectric semiconductors have been considered to be potential candidates for self-powered/multi-functional devices due to their piezotronic coupling effect. In this dissertation, ZnO and CdSe nanowire arrays have been synthesized as the piezoelectric semiconductor materials to develop the following self-powered/multi-functional sensors: (1) self-powered gas sensors of ZnO/SnO₂, ZnO/In₂O₃, ZnO/WO₃ and CdSe nanowire arrays have been …