Semiconductor and Optical Materials Commons^™

Model-Based Design Of An Optimal Lqg Regulator For A Piezoelectric Actuated Smart Structure Using A High-Precision Laser Interferometry Measurement System, Grant P. Gallagher

Master's Theses

Smart structure control systems commonly use piezoceramic sensors or accelerometers as vibration measurement devices. These measurement devices often produce noisy and/or low-precision signals, which makes it difficult to measure small-amplitude vibrations. Laser interferometry devices pose as an alternative high-precision position measurement method, capable of nanometer-scale resolution. The aim of this research is to utilize a model-based design approach to develop and implement a real-time Linear Quadratic Gaussian (LQG) regulator for a piezoelectric actuated smart structure using a high-precision laser interferometry measurement system to suppress the excitation of vibratory modes.

The analytical model of the smart structure is derived using the …

Inquiry Of Graphene Electronic Fabrication, John Rausch Greene

Master's Theses

Graphene electronics represent a developing field where many material properties and devices characteristics are still unknown. Researching several possible fabrication processes creates a fabrication process using resources found at Cal Poly a local industry sponsor. The project attempts to produce a graphene network in the shape of a fractal Sierpinski carpet. The fractal geometry proves that PDMS microfluidic channels produce the fine feature dimensions desired during graphene oxide deposit. Thermal reduction then reduces the graphene oxide into a purified state of graphene. Issues arise during thermal reduction because of excessive oxygen content in the furnace. The excess oxygen results in …

A Platform For Fast Detection Of Let-7 Micro Rna Using Polyaniline Fluorescence And Image Analysis Techniques, Partha P. Sengupta

Master's Theses

The project describes a new strategy for transducing hybridization events through modulating intrinsic properties of the electroconductive polymer polyaniline (PANI). When DNA based probes electrostatically interact with PANI, its fluorescence properties are increased, a phenomenon that can be enhanced by UV irradiation. Hybridization of target nucleic acids results in dissociation of probes causing PANI fluorescence to return to basal levels. By monitoring restoration of base PANI fluorescence as little as 10^-11 M (10 pM) of target oligonucleotides could be detected within 15 minutes of hybridization. Detection of complementary oligos was specific, with introduction of a single mismatch failing to …

Morphology-Property Relationship For Binary Organic Thin Films, Alyssa Lynn Griffin

Master's Theses

Organic thin films can be readily mass-produced through solution-based fabrication methods including ink-printing and solution-casting because their light weight, flexibility, and inexpensive sources. Their applications range from organic field-effect transistors (OFET), organic solar cells (OSC), to organic light emitting diodes (OLEDs). Compared with pure component films, binary organic thin films (BOTF) allows for novel characteristics and specialized features to handle more demanding tasks. Due to the complex intermolecular interactions in BOTF, various microscopic phases with different morphological and electronic properties may be formed and this information is difficult to extract through conventional bulk measurements.

Organic thin films can be readily …

Effect Of Surfactant Architecture On Conformational Transitions Of Conjugated Polyelectrolytes, Greg A. Braggin

Master's Theses

Water soluble conjugated polyelectrolytes (CPEs), which fall under the category of conductive polymers, possess numerous advantages over other conductive materials for the fabrication of electronic devices. Namely, the processing of water soluble conjugated polyelectrolytes into thin film electronic devices is much less costly as compared to the processing of inorganic materials. Moreover, the handling of conjugated polyelectrolytes can be performed in a much more environmentally friendly manner than in the processing of other conjugated polymers because conjugated polyelectrolytes are water soluble, whereas other polymers will only dissolve in toxic organic solvents. The processing of electronic devices containing inorganic constituents such …

Development Of A High Precision Quantum Dot Synthesis Method Utilizing A Microfluidic Reactor And In-Line Fluorescence Flow Cell, William Henry Lafferty

Master's Theses

Quantum dots show great potential for use as spectral converters in solar cells, lighting applications, and biological imaging. These applications require precise control of quantum dot size to maximize performance. The quality, size, and fluorescence of quantum dots depend on parameters that are difficult to control using traditional batch synthesis processes. An alternative, high precision process was developed for the synthesis of cadmium-selenide quantum dots using a microfluidic reactor and fluorescence flow cell. The process required creating separate cadmium and selenium precursors that were then mixed in a nitrogen environment at 17°C. Using an NE-300^® syringe pump, the solution …

Development Of A Silicon Nanowire Mask Using Scanning Probe Microscopy, Ross Gregoriev

Master's Theses

Scanning probe microscopy techniques were used to investigate the desorption of hydrogen passivated silicon to form SiO2 etch masks The application of the etch masks were planned on being used to manufacture silicon nanowires. Low concentration hydrofluoric acid was used to passivate the surface. The surface was selectively depassivated by SPM techniques. Scanning tunneling microscopy (STM) and atomic force microscopy (AFM) were used to create the masks. The STM system used was found to desorb hydrogen from the surface faster than the STM could image and was considered incapable in the configuration investigated. This led to the use of atomic …

Interfacial Interactions Between Carbon Nanoparticles And Conjugated Polymers, Yanqi Luo

Master's Theses

Conjugated polymer based electronics, a type of flexible electronic devices, can be produced from solution by traditional printing and coating processes in a roll-to-roll format such as papers and graphic films. This shows great promise for the emerging energy generation and conversion. The device performance of polymer electronics is largely dependent of crystalline structures and morphology of photoactive layers. However, the solution crystallization kinetics of conjugated polymers in the presence of electron acceptor nanoparticles has not been fully understood yet. In this study, solution crystallization kinetics of poly (3-hexylthiophene) in the presence of carbon nanotubes and graphene oxide has been …

Synthesis And Characterization Of Cdse/Zns Core/Shell Quantum Dot Sensitized Pcpdtbt-P3ht:Pcbm Organic Photovoltaics, Buddy J. Bump

Master's Theses

Durable, cheap, and lightweight polymer based solar cells are needed, if simply to meet the demand for decentralized electrical power production in traditionally “off-grid” areas. Using a blend of Poly(3-hexylthiophene-2,5-diyl) (P3HT), Phenyl-C61-butyric acid methyl ester (PCBM), and the low band-gap polymer Poly[2,6-(4,4-bis-(2- ethylhexyl)-4H-cyclopenta [2,1-b;3,4-b′]dithiophene)-alt-4,7(2,1,3-benzothiadiazole)] (PCPDTBT), we have fabricated devices with a wide spectral response and 3% power conversion efficiency in AM 1.5 conditions; however, this thin film system exhibits only 0.43 optical density at 500 nm. To improve the performance of this polymer blend photovoltaic, we aim to increase absorption by adding CdSe(ZnS) core (shell) quantum dots. Four groups of …

Developent Of A Phospholipid Encapsulation Process For Quantum Dots To Be Used In Biologic Applications, Logan Grimes

Master's Theses

The American Cancer Society predicts that 1,665,540 people will be diagnosed with cancer, and 585,720 people will die from cancer in 2014. One of the most common types of cancer in the United States is skin cancer. Melanoma alone is predicted to account for 10,000 of the cancer related deaths in 2014. As a highly mobile and aggressive form of cancer, melanoma is difficult to fight once it has metastasized through the body. Early detection in such varieties of cancer is critical in improving survival rates in afflicted patients. Present methods of detection rely on visual examination of suspicious regions …

Design, Implementation, And Test Of A Micro Force Displacement System, Evan Derek Cate

Master's Theses

The design and implementation of a micro-force displacement system was completed to test the force-displacement characteristics of square silicon diaphragms with side lengths of 4mm, 5mm, and 7mm with a thickness of 10um. The system utilizes a World Precision Instruments Fort 10g force transducer attached to a World Precession Instruments TBM4M amplifier. A Keithley 2400 source meter provided data acquisition of the force component of the system. A micro prober tip was utilized as the testing probe attached to the force transducer with a tip radius of 5um. The displacement of samples was measured using a Newport M433 linear stage …

Design And Fabrication Of Electrostatically Actuated Serpentine-Hinged Nickel-Phosphorous Micromirror Devices, Nicholas A. Wiswell

Master's Theses

A process for micromachining of micro-mirror devices from silicon-on-insulator wafers was proposed and implemented. Test methods and force applicators for these devices were developed. Following successful fabrication of these devices, a novel process for fabrication of devices out of the plane of the silicon wafer was proposed, so that the devices could be actuated electrostatically. In particular, the process makes use of thick photoresist layers as a sacrificial mold into which an amorphous nickel-phosphorous alloy may be deposited. Ideal design of the electrostatically actuated micro-mirrors was investigated, and a final design was selected and modeled using FEA software, which found …

Investigation Of Degradation Effects Due To Gate Stress In Gan-On-Si High Electron Mobility Transistors Through Analysis Of Low Frequency Noise, Michael Curtis Meyer Masuda

Master's Theses

Gallium Nitride (GaN) high electron mobility transistors (HEMT) have superior performance characteristics compared to Silicon (Si) and Gallium Arsenide (GaAs) based transistors. GaN is a wide bandgap semiconductor which allows it to operate at higher breakdown voltages and power. Unlike traditional semiconductor devices, the GaN HEMT channel region is undoped and relies on the piezoelectric effect created at the GaN and Aluminum Gallium Nitride (AlGaN) heterojunction to create a conduction channel in the form of a quantum well known as the two dimensional electron gas (2DEG). Because the GaN HEMTs are undoped, these devices have higher electron mobility crucial for …

Fabrication And Characterization Of A Palladium/Porous Silicon Layer, Nicholas Hong Lui

Master's Theses

When porous silicon is plated with a catalytic metal, the two materials can act together as a single entity whose electrical properties are sensitive to its environment – the sensing component of an electrochemical gas sensor. Etching pores into silicon is an electrochemical process; and which type of doped silicon used is one of its key parameters. For nearly all reported porous silicon gas sensors, the silicon has been of the p-doped variety – because p-doped porous etching is better understood and the layers that result from it are more predictable – despite n-doped silicon having potentially significant benefits in …

The Design And Fabrication Of An Electrostatically Actuated Diaphragm With A Silicon-On-Insulator Wafer, Elizabeth L. Brooks

Master's Theses

Electrostatically actuated silicon membranes were designed, modeled, fabricated, and characterized. The intended application was for use in a microspeaker. Fabrication issues necessitated the use of thick diaphragms with a large gap between the electrodes. The devices did not function as speakers but did show actuation with a high DC voltage. Device dimensions were chosen by examining membrane mechanics, testing the processing steps required for device fabrication, and modeling with COMSOL. Several adhesives were researched to fabricate the device sidewalls, including BCB, PMMA, and TRA-Bond F112. A method for patterning PMMA through photolithography was found using a scanning electron microscope. Masks …

Constructing And Optimizing A Single Wafer Solar Cell Array In The Microfabrication Lab At California Polytechnic State University At San Luis Obispo, Rod Marstell

Master's Theses

CONSTRUCTING AND OPTIMIZING A SINGLE WAFER SOLAR CELL ARRAY IN THE MICROFABRICATION LAB AT CALIFORNIA POLYTECHNIC STATE UNIVERSITY AT SAN LUIS OBISPO

Solar cells are more and more becoming a significant source of energy in the world today. They are used to power entire buildings as well as small devices and everything in between, and are utilized all around the world. Smaller solar devices, such as hearing aid battery chargers, cost a lot of money relative to the monetary wealth in third-world countries. For this purpose, a less expensive, more efficient solar cell array should be developed.

This study contains …

The Fabrication & Characterization Of An Electrokinetic Microfluidic Pump From Su-8, A Negative Epoxy-Based Photoresist, Nash Anderson

Master's Theses

Microfluidics refers to manipulation, precise control, and behavior of fluids at the micro and nanoliter scales. It has entered the realm of science as a way to precisely measure or mix small amounts of fluid to perform highly controlled reactions. Glass and polydimethylsiloxane (PDMS) are common materials used to create microfluidic devices; however, glass is difficult to process and PDMS is relatively hydrophobic. In this study, SU-8, an epoxy based (negative) photoresist was used to create various electrokinetic microfluidic chips. SU-8 is commonly used in microelectromechanical design. Spin coating of various SU-8 formulations allows for 1 μm to 100 μm …

Characterization And Modeling Of An O-Band 1310 Nm Sampled-Grating Distributed Bragg Reflector (Sg-Dbr) Laser For Optical Coherence Tomography (Oct) Applications, Desmond Charles Talkington

Master's Theses

In this project, the performance aspects of a new early generation 1310 nm Sampled-Grating Distributed Bragg Reflector (SG-DBR) semiconductor laser are investigated. SG-DBR lasers are ideal for Source Swept Optical Coherence Tomography (SS-OCT), a Fourier-Domain based approach for OCT, necessitating a tunable wavelength source. Three internal sections control the frequency output for tuning, along with two amplifiers for amplitude control. These O-band SG-DBR devices are now being produced in research quantities. SG-DBR lasers have been produced at 1550 and 1600 nm for some times. Fundamental questions regarding the performance of the 1310 nm devices must be quantified. Standard metrics including …

Dc, Rf, And Thermal Characterization Of High Electric Field Induced Degradation Mechanisms In Gan-On-Si High Electron Mobility Transistors, Matthew Anthony Bloom

Master's Theses

Gallium Nitride (GaN) high electron mobility transistors (HEMTs) are becoming increasingly popular in power amplifier systems as an alternative to bulkier vacuum tube technologies. GaN offers advantages over other III-V semiconductor heterostructures such as a large bandgap energy, a low dielectric constant, and a high critical breakdown field. The aforementioned qualities make GaN a prime candidate for high-power and radiation-hardened applications using a smaller form-factor. Several different types of semiconductor substrates have been considered for their thermal properties and cost-effectiveness, and Silicon (Si) has been of increasing interest due to a balance between both factors.

In this thesis, the DC, …

Quantum Dot Deposition Into Pdms And Application Onto A Solar Cell, Christopher Marcus Botros, Richard N. Savage

Master's Theses

Research to increase the efficiency of conventional solar cells is constantly underway. The goal of this work is to increase the efficiency of conventional solar cells by incorporating quantum dot (QD) nanoparticles in the absorption mechanism. The strategy is to have the QDs absorb UV and fluoresce photons in the visible region that are more readily absorbed by the cells. The outcome is that the cells have more visible photons to absorb and have increased power output. The QDs, having a CdSe core and a ZnS shell, were applied to the solar cells as follows. First, the QDs were synthesized …

Fabrication And Characterization Of Torsional Micro-Hinge Structures, Mike Madrid Marrujo

Master's Theses

ABSTRACT

Fabrication and Characterization of Torsional Micro-Hinge Structures

Mike Marrujo

There are many electronic devices that operate on the micrometer-scale such as Digital Micro-Mirror Devices (DMD). Micro actuators are a common type of DMD that employ a diaphragm supported by torsional hinges, which deform during actuation and are critical for the devices to have high stability and reliability. The stress developed within the hinge during actuation controls how the actuator will respond to the actuating force. Electrostatically driven micro actuators observe to have a fully recoverable non-linear viscoelastic response. The device consists of a micro-hinge which is suspended by two …

The Effect Of Polarization And Ingan Quantum Well Shape In Multiple Quantum Well Light Emitting Diode Heterostructures, Patrick M. Mcbride

Master's Theses

Previous research in InGaN/GaN light emitting diodes (LEDs) employing semi-classical drift-diffusion models has used reduced polarization constants without much physical explanantion. This paper investigates possible physical explanations for this effective polarization reduction in InGaN LEDs through the use of the simulation software SiLENSe. One major problem of current LED simulations is the assumption of perfectly discrete transitions between the quantum well (QW) and blocking layers when experiments have shown this to not be the case. The In concentration profile within InGaN multiple quantum well (MQW) devices shows much smoother and delayed transitions indicative of indium diffusion and drift during …

Deposition, Characterization, And Fabrication Of A Zinc Oxide Piezoelectric Thin Film Microspeaker Using Dc Reactive Sputtering, Adam Olzick

Master's Theses

A piezoelectric microspeaker device that could be used in a variety of acoustic applications was designed and fabricated using a thin film ZnO layer that was reactively DC sputtered onto a single crystalline n-type silicon substrate. When tested the microspeaker did not produce sound due to complications in the etching process, the thickness of the diaphragms, and clamping effects. Instead, a characterization approach was taken and the structural, optical, electrical, and piezoelectric properties of the ZnO were investigated. Scanning electron microscopy, x-ray diffraction, and atomic force microscopy were utilized to discover the ZnO’s structural properties. Using the XRD and SEM, …

The Design And Fabrication Of A Microfluidic Reactor For Synthesis Of Cadmium Selenide Quantum Dots Using Silicon And Glass Substrates, Peter Robert Gonsalves

Master's Theses

A microfluidic reactor for synthesizing cadmium selenide (CdSe) quantum dots (QDs) was synthesized out of a silicon wafer and Pyrex glass. Microfabrication techniques were used to etch channels into the silicon wafer. Holes were wet-drilled into the Pyrex glass using a diamond-tip drill bit. The Pyrex wafer was anodically bonded to the etched silicon wafer to enclose the microfluidic reactor. Conditions for anodic bonding were created by exposing the stacked substrates to 300V at ~350oC under 5.46N of force. A syringe containing a room temperature CdSe solution was interfaced to the microfluidic reactor by using Poly (dimethylsiloxane) (PDMS) as an …

Synthesis, Field Emission And Associated Degradation Mechanisms Of Tapered Zno Nanorods, Gregory M. Wrobel Mr.

Master's Theses

Equation 1..... 4

Equation 2..... 4

Equation 3..... 6

Equation 4..... 7

Equation 5..... 9

Equation 6..... 10

Equation 7..... 11

Equation 8..... 12

Equation 9..... 14

Equation 10..... 40

Equation 11..... 51

Synthesis, Field Emission and Associated Degradation Mechanisms of Tapered ZnO Nanorods

Gregory Michael Wrobel, M.S.

University of Connecticut, 2011

Modern development of field emitter arrays (FEA) has been made possible, partly thanks to the synthesis and development of one-dimensional (1D) nanostructures. High aspect ratio 1D nanostructures effectively amplify the electric field at the emitter tips, allowing electrons to be extracted at relatively low electric field. An inexpensive …

Fabrication And Characterization Of Zno/Cuo Core-Shell Nanowire Arrays, Kuo-Ting Liao

Master's Theses

Research into nanomaterials has become more and more popular because of their unique properties compared to bulk materials. Amongst various functional materials, zinc oxide (ZnO), with a direct electron energy band gap of 3.34 eV at room temperature, is an important optoelectronic material with an intrinsically n-type semiconducting property. However, to form a p-type ZnO semiconductor is still a challenge. Copper oxide (CuO), compared to ZnO, has a much smaller band gap, 1.2 eV, and shows an intrinsically p-type semiconducting property. It has been suggested that when CuO is alloyed with ZnO properly, a p-n semiconductor heterojunction can be formed …

Design, Fabrication, And Characterization Of A Thin-Film Nickel-Titanium Shape Memory Alloy Diaphragm For Use In Micro-Electro-Mechanical Systems, Brian Joel Alvarez

Master's Theses

Previous work done at Cal Poly has shown that thin-film nickel-titanium (NiTi) can be easily sputtered onto silicon wafers and annealed to create a crystallized shape memory alloy (SMA) film. Initial work on creating devices yielded cantilevers that were highly warped due to thin-film stress created during the sputtering process. The objective of this work was to create a thin-film NiTi SMA device that could be better characterized. A membrane was selected due to the simplicity of fabrication and testing which would also oppose the thin-film stress due to the increase in attachment points to the substrate.

Silicon wafers were …

Synthesis And Characterization Of Cdse-Zns Core-Shell Quantum Dots For Increased Quantum Yield, Joshua James Angell

Master's Theses

Quantum dots are semiconductor nanocrystals that have tunable emission through changes in their size. Producing bright, efficient quantum dots with stable fluorescence is important for using them in applications in lighting, photovoltaics, and biological imaging. This study aimed to optimize the process for coating CdSe quantum dots (which are colloidally suspended in octadecene) with a ZnS shell through the pyrolysis of organometallic precursors to increase their fluorescence and stability. This process was optimized by determining the ZnS shell thickness between 0.53 and 5.47 monolayers and the Zn:S ratio in the precursor solution between 0.23:1 and 1.6:1 that maximized the relative …

Feasibility Of Manipulating Correlated Color Temperatures With A Phosphor Converted High-Powered Light Emitting Diode White Light Source, Matthew Michael Little

Master's Theses

In this thesis we examine the feasibility of developing a white light source capable of producing colors between 2500 and 7500 Kelvin on the black-body radiator spectrum by simply adjusting amperage to a blue and ultraviolet (UV) light emitting diode (LED). The purpose of a lighting source of this nature is to better replicate daylight inside a building at a given time of day. This study analyzes the proposed light source using a 385 nm UV LED, a 457 nm blue LED, a 479 nm blue LED, a 562 nm peak cerium doped yttrium aluminum garnet (YAG:Ce) phosphor, and a …

Enhanced Light Extraction Efficiency From Gan Light Emitting Diodes Using Photonic Crystal Grating Structures, Simeon S. Trieu

Master's Theses

Gallium nitride (GaN) light emitting diodes (LED) embody a large field of research that aims to replace inefficient, conventional light sources with LEDs that have lower power, higher luminosity, and longer lifetime. This thesis presents an international collaboration effort between the State Key Laboratory for Mesoscopic Physics in Peking University (PKU) of Beijing, China and the Electrical Engineering Department of California Polytechnic State University, San Luis Obispo. Over the course of 2 years, Cal Poly’s side has simulated GaN LEDs within the pure blue wavelength spectrum (460nm), focusing specifically on the effects of reflection gratings, transmission gratings, top and bottom …