Biomechanical Engineering Commons^™

Design And Fabrication Of 3d Bioprinted Scaffold: Experimental And Machine Learning Methods, Mohan K. Dey

LSU Doctoral Dissertations

The development of reliable hydrogel-based scaffolds for extrusion bioprinting remains limited by the poor structural fidelity of low-viscosity bioinks and the lack of robust, high-throughput quality evaluation methods. This dissertation can resolve such challenges by developing the combination of optimized hydrogel formulations, cryogenic-assisted bioprinting, and artificial intelligence (AI)-based scaffold evaluation to the use of tissue engineering and preclinical cancer modelling applications. To assess the rheological behavior, printability, mechanical properties, and biocompatibility of the alginate – gelatin (Alg–Gel) system, a novel system of hydrogel was developed and characterized using Alg–Gel hydrogel system. The 7% alginate, 8% gelatin mixture was found to …

An Investigation Of Pelvic Kinematics And Implications For Total Hip Arthroplasty, Kathryn Holland Colone

Electronic Theses and Dissertations

Total hip arthroplasty (THA) is one of the most commonly performed orthopaedic procedures, with approximately 500,000 surgeries performed annually in the United States alone. Although THA is widely regarded as highly successful, postoperative complications persist, highlighting the multifactorial nature of THA outcomes. Previous studies have demonstrated the importance of implant positioning and soft tissue mechanics, yet challenges remain in optimizing surgical decisions on a patient-specific basis. Recent advances in surgical planning tools have shifted the focus of preoperative planning toward optimizing patient-specific outcomes, highlighting the need to better understand how patient anatomy, surgical technique, and joint mechanics interact to influence …

Time-Frequency Analysis Of Arterial Pulse Signals Of Cardiovascular Disease Patients Measured By A Microfluidic-Based Tactile Sensor, Md Mahfuzur Rahman

Mechanical & Aerospace Engineering Theses & Dissertations

This dissertation presents a single-degree-of-freedom (SDOF) based time–frequency analysis framework that can simultaneously extract a comprehensive set of cardiovascular autonomic indices from arterial pulse wave recordings obtained at rest and post-exercise, supporting non-invasive monitoring of autonomic recovery during cardiac rehabilitation. The framework rests on three technical contributions.

First, an SDOF analytical model of motion artefacts quantifies two physically distinct distortion mechanisms: additive baseline drift and Time-Varying System Parameter (TVSP) generated distortion of the Tissue-Contact-Sensor (TCS) stack. Baseline drift is slowly varying and removable by filtering; TVSP distortion rides on all harmonics of the true pulse signal and cannot be removed …

Smart Sleeve, Evan Abalos, Bright Jung, Owen Bowling, Wyatt Eberhart

Mechanical Engineering

Quantifying human arm muscle activity is essential for understanding human movements and helping individuals who suffer from motor or neurological impairments such as stroke or traumatic brain injuries. Today, these individuals, as well as clinicians, researchers, and athletes, face many challenges when using the traditional surface electromyography (sEMG) systems to monitor muscle activities, including complex setup, restricted mobility, discomfort, inconsistent placement of electrodes, and lack of accuracy. Therefore, a comfortable EMG sleeve device that accurately measures arm movement without interfering with daily tasks is needed, which the team will be designing, manufacturing, and testing as their senior project. In addition, …

Cathy’S Catcher, Marlee Scott, Regen Worsley, Alessandra Valenzano, Aviv Ben Zeev

Mechanical Engineering

Deep-sea fishing presents significant challenges for individuals with upper-limb differences, particularly when using prosthetic devices that are not designed for recreational fishing activities. This project developed a custom prosthetic fishing rod attachment for a user who had lost her forearm and desired a safe, comfortable, and independent method of fishing. Through interviews with the sponsor and an iterative design process, a lightweight aluminum attachment was created to interface directly with the user's existing prosthetic quick-connect system.

The design process included concept generation, CAD modeling, rapid prototyping with 3D-printed models, manufacturing, and user-centered refinement. The final design consists of a welded …

Design And Evaluation Of An Assistive Powered Hand Orthosis For Grasp Activities For People Post-Stroke, Sydney Alexander

Master's Theses

After suffering a stroke, many survivors experience physical disability that affects their ability to complete daily tasks using their hands. Physical therapy is often pre scribed to people post-stroke, but is not fully effective at restoring hand function. The goal of this project was to design and fabricate an assistive device for people post-stroke to help with grasp and release. The device was designed to address com mon shortcomings of existing similar devices. State of the art devices in this domain were investigated to determine a set of design improvements. A novel motor-actuated hand orthosis was designed to decrease weight, …

Du Undergraduate Showcase Abstracts: Research, Scholarship, And Creative Works, Sophia Wismar, Henry Staats, Allison Metzler, Chloe Puckett, Rachel Levine, Christa Kilpatrick, Scott Wolf, Joe Walsh, Grace Doolittle, John Engebreston, Zoe Lopez, Christopher Aaby, Audrey Duff, Timothy Sisk, Katelyn Lamberton, Angela Narayan, Gilkah Argueta, Habiba Samir, Girena Tesfazghi, Genet Kenore, Sinit Tesfamariam, Effley Brooks, Abi Newell, Megan Doherty, Natalie Baer, Lexi Blood, Talya Riciputi, Jessica Jimenez, Devin Hernandez, Lynn Clark, Taj Kumar, Sunil Kumar, Allen Rutman, Mira Pronobis, Tess Carson, Anna Sher, Frankie Stroud, Tamra Pearson D'Estree, Alyssa Wilson, Emily Melnick, Jenalee Doom, Yihang Gao, Gwendolyn Geiger, Noah Gettle, Scott Nichols, Clare Ayoub, Cara Dienno, Sunny Walker, Zoe Hansen, Maya Wheeler, Addison Rice, Patrick Martin, Sanjana Acharya, Daniel Mcintosh, Amanda Mckellips, Calli Cain, Justin Blake, Peter Sokol-Hessner, Natalie Miller, Max Weisbuch, Sophia Dellota, John Macikas, Charlotte Snow, Mark Siemens, Zoe Lynch, Alex Huffman, Prachi Shah, Jason Roney, Halcyon Levi, Nicole Herzog, Andrea Koly, Daniel Linseman, Annie London, Xi Yang, Avery Zwisler, Jane Smith, Chaz Contag, Michael Kerwin, Lucy Rand, Grace Schroeder, Michelle Rozenman, Nissa Tapper, Guiming Zhang, Mateo Mazariego-Halpern, Keith Meyer, Julie Do, Dakota Park-Ozee, Travis Herink, Kara Neu, Jonathan Plomin, Eve-Odine Duchaufour, Debbie Gale Mitchell, Tennyson Anderson-Stricklin, Lily Treitz, Samantha Rosenberger, Sierra Griffith, Finley Joseph, Daniel Sampson, Emmy Davis, Skyler Kasnoff, Evon Lopez, Vivian Nguyen, Cassy Young, Franklin Sellner, Martin Tobon, Ila Graham, Zach Billings, Holden Hedit, Decatur Boland, Paul Kosempel, Cory Chandler, Jay Mahoney, Sam Dragan, Susan Dagget, Yarrow Ator, Heidi Vuletich, Owen Weber, Andrew Kloeppel, Petersen Gray, Mandi Schaeffer-Fry, Razleen Bassra, Bryanna Rodriguez, Christina Blue, Taubie Sanders, Rachel Epstein, Luke Milburn, Camryn Evans, Ezra Martinez, Mary Westwood, Gabri Notov, Robin Tinghitella, Lilou Cabrol, Eli Barbour, Juliet Mendik, Selma Myers, Zac Wise, Noah Fahlin, Michelle Knowles, Abigail Hopper, Michael Greenberger, Romi Laclair, Sarah Watamura, Sabrina Efroymson, Casey Barker, Sydney Seltzer, Bryn Yehle, Jennifer Hoffman, Sara Garcia, Ryuka Nagamine, Trevor Briggs, Remy Le Boeuf, Elena Krone, Eileen Farrell, Regan O'Rourke, Elena Roel, Greg Mortimer, Ali Ayoub, Stefani Langehennig, Caitlin Turk, Logan Scmid, Stefan Chavez-Norgaard, Karen Kim, Tatiana Peccedi, Courtney Cassidy, John Sebesta, Rhianna Lewis, Janice Bening-Lacek, Vivian Lawless, Mckenna Hanson, Jeffrey Amidon, Riya Joshi, Ram Ambre, Brady Worrell, Perrin Schneider, Ali Azadani, Brooke Agulnek, Lyndsie Salvagio, Elise Siemanowki, Yan Qin, Andre Allen, Melodie Nguyen, Megan Livengood, Abby Reams, Saffron Hartreeve, Bri Wylie, Sarah Brookman, Mariah Loiacono, Green Russo, Abhia Lodhi, Gabrielle Welsh, Nika Spehar, Shahked Levin, Evrim Baykal, Kimberly Chiew, Jocelyn Torres, Kailey Hicks, Mykaela Tanino-Springsteen, Audrey Bellows, Akam Chahal, Madeline Tepper, Shannon Murphy, Alexa Fonseca, Deborah Han, Cassandra Perez, Oluwatoyin Alaba, Julia Roncoroni, Vy Nguyen, Nana Burn, Sarah Sasse, Rubin Tuder, Anthony Gerber, Nancy Lorenzon, Christine Vohwinkel, Camryn Gunter, Tristan Weber, Sam Rommel, Brian Michel, Muskan Fatima, Alannah Oleson, Kira Frey, Edward Garrido, Beckett Morris, Kerstin Haring, Drew Middleton, Abigail Walpert, Liam Dee, Gabby Ishaw, Cole Carnes, Maddie Weiser, Claire Fox, Valeriia Vlasenko, Kateri Mcrae, Riley Smith, Abigail Templin, Kushani Rajapaksha

DU Undergraduate Research Journal Archive

Abstracts from the DU Undergraduate Research Showcase.

Effects Of A Passive Assistive Hamstring Device On Overground Running Kinematics And Hamstring Activation., Quinn Castner

All Theses

Hamstring strain injuries are among the most common and recurring injuries in sports, occurring most often during the terminal swing phase of gait. Despite progress in rehabilitation, the incidence of injury has only increased, suggesting a need for a novel intervention. We designed a passive, assistive, wearable device with two specific criteria in mind: to offload the hamstrings during running, and do so without hindering normal kinematic patterns. The device consists of an adjustable elastic band anchored proximally at the waist and distally just above the ankle joint center. It stretches and shortens with the hamstrings, providing passive hip extension …

Development Of Low-Cost Triaxial Force Sensor For Measurement Of Human-Exoskeleton Interaction Forces, Hamdan Khan Sarvathullah

All Theses

Contemporary research suggests that shear force is a major contributor to discomfort and pressure injury. However, the variation of shear forces during human-exoskeleton interaction dynamics is a highly unexplored field. The high cost of commercial triaxial force sensors may be a major factor in the notable lack of research in this field. Therefore, in this paper, we present a low-cost, 3D-printed triaxial force sensor designed specifically to measure the triaxial interaction forces between an exoskeleton and its user. The triaxial force sensor uses Carbon-Black/Silicone Rubber (CB/SR) strings to measure shear forces, whereas the normal force is measured with a Force …

An Experimental Study Of The Morphology Of Dna-Carbon Nanotube Hybrid Structures In Direct Dna Sequencing, Avery P. Davis

Biomedical Engineering Undergraduate Honors Theses

Hybrid structures formed between single-stranded DNA (ssDNA) and single-walled carbon nanotubes (SWCNT) have emerged as promising components in future direct DNA sequencing technologies due to their unique morphological and electronic properties. The nanoscale configuration of these hybrids, including the DNA wrapping angle, pitch, and contour behavior, directly influences their potential for stable electronic readout. This thesis presents an experimental study of DNA-SWCNT hybrid morphology using a fixed, reproducible wrapping protocol designed to minimize environmental variability and isolate the influence of DNA nucleotide sequence on hybrid structure. As described in prior work, this protocol produces well-dispersed hybrids suitable for high-resolution imaging. …

Exercise-Induced Muscle Damage As A Model For Exploring The Effects Of Pain On Gait, Sydney Savage

All Theses

Persistent gait asymmetry following anterior cruciate ligament reconstruction (ACLR) is a recognized contributor to post-traumatic knee osteoarthritis, yet the independent role of pain in driving altered movement patterns remains poorly understood due to confounding factors inherent to clinical populations. This study used exercise-induced muscle damage (EIMD) as a controlled experimental model to isolate the effects of musculoskeletal pain on gait, independent of kinesiophobia, structural damage, and proprioceptive disruption. Eighteen healthy adults underwent unilateral eccentric calf-raise protocols to induce delayed onset muscle soreness (DOMS), with gait assessed at baseline, 48 hours, and 168 hours post-exercise using bilateral inertial measurement units. Outcomes …

Experimental And Computational Investigation Of The Effects Of Neck Musculature During Head Impacts In American Football, Anthony P. Marino

All Dissertations

Anthropometric test devices (ATDs) are human surrogate models used to represent the human body response in the context of compliance and safety testing. These devices are used in multiple industries, including automotive and aerospace, and have recently been incorporated into impact testing for the evaluation of helmet performance in American football. The Hybrid III 50^th percentile male ATD head and neck assembly is the most commonly used surrogate for these tests, although it was developed for automotive frontal crash scenarios that induce an inertial force on the body, leading to head and neck motion primarily in the sagittal plane. …

Multiscale Architecture Governs Stability In Suction-Actuated Variable Stiffness Catheters, Sheridan Lee

McKelvey School of Engineering Graduate Student Theses & Dissertations

Endovascular procedures require devices with widely varying mechanical properties: flexibility for navigating tortuous vessels and rigidity for stable therapeutic delivery. Suction-actuated variable stiffness sheaths address this challenge by incorporating axial wire string arrays that mechanically couple under suction to increase flexural rigidity. However, prototype devices achieve stiffening ratios below theoretical predictions, suggesting that interlayer mechanics and string positioning play a critical role. This study investigates whether interweaving polytetrafluoroethylene (PTFE) tape within the string array enhances flexural rigidity modulation and curvature stability. Prototype devices with varying wrap configurations were fabricated and evaluated using flexural testing, curvature stability testing, and mathematical modeling. …

Implantable, Sensor-Embedded Vascular Graft Towards Wireless Monitoring Of Stenosis, Nnamdi Dike

LSU Master's Theses

Arteriovenous (AV) grafts are commonly used to provide vascular access for hemodialysis in patients with end-stage renal disease. Despite their widespread use, AV grafts are prone to complications such as stenosis and thrombosis. Early detection of these conditions remains challenging with current monitoring methods too costly or insufficient. This work presents the design, fabrication, and validation of an LC pressure sensor embedded within a model AV graft to enable real-time monitoring. The proposed system integrates a parallel-plate capacitive pressure sensor with a spiral inductor to form an LC circuit embedded within an elastomeric graft wall. The Ecoflex 00-30 dielectric layer …

Numerical Study Of Nutrient Mixing In Trabecular Bone In Microgravity, Disuse And Normogravity, Sagar Gharti

Doctoral Dissertations and Master's Theses

Mechanical loading is known to regulate bone remodeling by driving interstitial fluid flow which stimulates cells and drives nutrient transport within the trabecular network. In microgravity, the absence of mechanical stimulation or loading suppresses convective flow processes, causing diffusion-driven nutrient mixing and renewal, and accelerated bone loss. This thesis investigates how oscillation frequency and trabecular bone density jointly control nutrient mixing and wall shear stress within trabecular cavities.

A computational fluid dynamics (CFD) framework is developed in STAR-CCM+ using a soft-cap oscillation model that mimics cyclic compression. Three idealized trabecular morphologies are simulated across different frequencies to represent microgravity or …

Wearable Sensor System Used To Measure Linear And Angular Acceleration Of The Head Of American Football Players, David A. Emerson

LSU Master's Theses

American football players are repeatedly subject to high-velocity impacts; collisions can exceed 100 g in the NFL [1]. Rotational accelerations of the head caused by high-velocity collisions have been proven to be extremely damaging to the highly organized brain fibers at the brain-skull interface [2]. The sensor system (SS) measures the nonplanar acceleration at four locations on a chin strap using ADXL314 accelerometers and utilizes rigid-body kinematics to estimate the head rotational state from the measured acceleration of the SS [3]. The SS was validated through progressive testing, including steady-state, linear impact, and rotational impact testing. The ADLX314 sensor exhibited …

Development Of An Automated Platform For Cell Biology Experiments, Dipendra Nepal

Shelby Hall Graduate Research Forum Posters

Cell biology experiments involve repetitive tasks such as pipetting, sample preparation, and imaging, which are typically performed manually. These manual processes can introduce variability, reduce efficiency, and increase the cost of biomedical research. To address these challenges, our lab is developing a modular robotic platform, iEye™, to automate key steps in cell biology workflows [1]. The system is designed as self-contained modules, allowing flexible development and integration of different functionalities. In this work, we focus on a sample preparation module that integrates a 6-degree-of-freedom robotic arm, a motorized stage, and a pneumatic pipetter. This module is being developed to automate …

Assessing The Geomechanical Modelling Of Underground Reservoir For Co₂ Storage Trapping Mechanisms, Bonavian Hasiholan, Mohammed Ali Farea, Elhassan Mostafa Abdallah, Sami Abdelrahman M. Yagoub, Yasir Mukhtar

Mathematical Modelling and Numerical Simulation with Applications

Effective carbon dioxide (CO₂) storage is essential for mitigating climate change amid increasing global greenhouse gas emissions. This study investigates the influence of geomechanics on CO₂ storage performance within carbon capture and storage (CCS), focusing on structural, residual, and solubility trapping mechanisms using a fully coupled modeling framework. Two numerical models, with and without geomechanical effects, are developed to evaluate impacts on reservoir behavior, CO₂ migration, and trapping efficiency. Each mechanism is analyzed separately and within an integrated framework to assess their combined contributions. Results indicate that geomechanical coupling increases reservoir pressure, reduces CO₂ flow velocity, enhances migration control, and …

Mechanical Characterization And Modeling Of Rat Myocardia Under The Influence Of Epirubicin, Abdallah Mahmoud Alkhaiyat

Theses and Dissertations

Cancer remains a predominant health challenge that is responsible for a significant portion of global morbidity and mortality. Epirubicin (EPI), a chemotherapeutic anti-cancer drug, has shown remarkable efficacy in combating various malignancies. However, it is known to have undesirable side effects on the heart, collectively referred to as cardiotoxicity. This research investigates the adverse effects of chemotherapy on cardiac contractility through an in vitro examination of the mechanics of healthy and infarcted animal heart tissues. Electrically stimulated slices of rat ventricular tissue were tested using an isometric force measurement tissue bath. The tissue slices were subjected to uniaxial stretching, allowing …

Influence Of Motion Artifacts On Instantaneous Frequency Based Heart Rate Variability Of Arterial Pulse Signals Measured By A Tactile Sensor: An Analytical Study, Mamun Hasan, Zhili Hao

Mechanical & Aerospace Engineering Faculty Publications

Objective: Heart rate variability (HRV), quantified via the instantaneous frequency (IF) of arterial pulse signals, is a key indicator of cardiovascular (CV) regulation. This study presents a theoretical and experimental investigation of how motion artifacts (MA) influence IF-and thus HRVmeasured with a tactile sensor, emphasizing underlying mechanisms rather than population-level validation. Approach: Building on a previously developed single-degree-of-freedom (SDOF) model of the tissue-contact-sensor (TCS) stack between the sensor and the artery, MA is represented as low-frequency baseline drift and time-varying system parameters (TVSP) of the TCS stack. Analytical expressions quantify the effect of MA on the IF of each harmonic …

Combining Haptic Feedback With Electromyography To Study Knee Injury In Stationary Cycling, Christopher Kirby

Honors Theses

Patellofemoral Pain Syndrome (PFPS) is the most prevalent overuse injury in cycling, often linked to altered neuromuscular activation patterns of the quadriceps and hamstrings. While sensory feedback has successfully modified cyclists posture, there is a critical lack of evidence-based interventions targeting the underlying muscle activation imbalances associated with chronic knee pain. This study aimed to develop and validate a novel, real-time biofeedback system that utilizes electromyography (EMG) to trigger vibrotactile cues, aiming to shift muscle onset timing earlier in the pedal stroke to mitigate PFPS-related imbalances. A closed-loop system was engineered by integrating a Delsys EMG system with a SageMotion …

Microgravity-Induced Alterations In Left Atrial Hemodynamics And Thrombogenic Risk: Insights From Healthy And Atrial Fibrillation Models, Grace M. Hoeppner

Dissertations, Master's Theses and Master's Reports

Background: Microgravity exposure alters cardiovascular loading, yet its impact on left atrial flow dynamics and thrombotic risk remains poorly understood. This study investigates how spaceflight-relevant microgravity-induced changes in cardiac outflow affect left atrial hemodynamics in healthy individuals and patients with atrial fibrillation.

Methods: Patient-specific left atrial models were generated for three healthy individuals and three AF patients. Computational fluid dynamics (CFD) simulations were performed using each patient’s baseline mitral outflow waveform and two modified waveforms representing short- and long-duration post-flight cardiac loading changes derived from echocardiographic observations. Hemodynamic metrics included left atrial velocity, time averaged wall shear stress, oscillatory shear …

The Development And Implementation Of A Computational Framework To Simulate Patellofemoral Joint Mechanics, Mahmood Rashedi

Master’s Theses

Anterior knee pain affects approximately 25% of adults and is associated with altered joint mechanics. Patellofemoral joint (PFJ) models vary widely in complexity, with no established gold standard. Musculoskeletal models efficiently estimate joint loading but do not capture tissue-level mechanics, whereas finite element (FE) models provide tissue-level predictions at greater computational cost. This thesis developed a workflow to evaluate relationships between musculoskeletal model-predicted PFJ loads and FE-predicted cartilage mechanics, examined the impact of altered quadriceps activation, and introduced improved computational models.

Marker trajectories and ground reaction forces were collected from four adults (2 male, 2 female) during walking and squatting. …

Automation And Habitat Development For A Space Based Marine Life Environment, Logan Trimmer, Alexander Hang

Harrisburg University Other Works

This project was a cross-collaboration between the Environmental Sciences and Advanced Manufacturing and Robotics programs for the company Monolith Space.

The goal of this project was to design an autonomous system to be able to track qualities of water in an aquaculture system designed to be sent to space.

Multi-Sensor Fusion For Manual Wheelchair State Estimation, Kathylee Pinnock Branford

Graduate Theses, Dissertations, and Problem Reports (ETD)

Kathylee Pinnock Branford Manual wheelchairs are essential to mobility and independence, yet accurately characterizing wheelchair motion in real-world environments remains challenging. Inertial measurement units (IMUs) provide a practical means of estimating wheelchair kinematics, but existing trajectory-reconstruction studies have largely been limited to short, controlled trials. This report developed and evaluated a four-IMU framework comprising one sensor on each rear wheel and two sensors on the wheelchair frame. Three orientation algorithms (VQF, Mahony AHRS, and Madgwick AHRS), two accelerometer ranges (±2 g and ± 4 g), and calibrated and uncalibrated sensor data were evaluated during indoor motion-capture trials and a outdoor …

Development And Evaluation Of A Smart Vacuum-Assisted Suspension System For Transtibial Prostheses, Zahraa Kathem Ali, Wajdi Sadik Aboud

Al-Bahir

A prosthetic socket is essential for achieving comfort, gait symmetry, and overall satisfaction for amputees. Effective suspension systems are crucial for securely attaching prostheses, thereby optimizing comfort, functional performance, and long-term limb health. This study aimed to develop and evaluate an intelligent vacuum-assisted suspension system for transtibial prostheses to improve socket fit, gait stability, and reduce residual limb movement. The system integrates force-sensitive resistors (FSRs) and an inertial measurement unit (MPU6050) with accelerometer and gyroscope sensors, continuously monitoring interface pressure and limb motion. Real-time data from these sensors dynamically adjusts vacuum pressure based on the user's gait pattern .Quantitative gait …

Expansion Limits Of Meshed Split-Thickness Skin Grafts, Haomin Yu

McKelvey School of Engineering Graduate Student Theses & Dissertations

Split-thickness skin grafts are widely used to treat chronic wounds. Procedure design requires surgeons to predict how much a patch of the patient's own skin expands when it is meshed with rows of slits and stretched over a larger wound area. Accurate prediction of graft expansion remains a challenge, with current models overestimating the actual expansion, leading to suboptimal outcomes. Inspired by the principles of mechanical metamaterials, we developed a model that distinguishes between the kinematic rearrangement of structural elements and their stretching, providing a more accurate prediction of skin graft expansion. Our model was validated against extensive data …

Three-Dimensional Printing Of Calcium Phosphate-Mesoporous Bioactive Glass Scaffolds For Bone Tissue Engineering, Ana Beatriz Gomes De Carvalho, Lais Medeiros Cardoso, Igor Paulino Mendes Soares, Joyce Rodrigues De Souza, Arpita Roy, Prabaha Sikder, Et. Al.

Mechanical Engineering Faculty Publications

Calcium phosphate cements (CPCs) and biomaterials, such as mesoporous bioactive glass (MBG), are critical for bone tissue engineering. This study aimed to 3D-print CPC scaffolds modified with MBG to enhance their osteogenic potential and regenerative ability. MBG powder was synthesized and characterized using transmission electron microscopy (TEM), X-ray diffraction (XRD), and nitrogen adsorption-desorption techniques. A commercial CPC ink (hydroxyapatite/alpha-tricalcium phosphate) was mixed with 5% MBG (w/w; CPC/MBG), and, after rheological assessment, the mixture was used to obtain scaffolds via 3D printing. These scaffolds were then tested for chemical, morphological, and mechanical properties, as well as ion release analysis. Unmodified CPC …

Design And Development Of Biomimetic Hydrogel Interfaces For Enhanced Bioelectrical Signal Acquisition, Daniela Nikoloska

UNLV Theses, Dissertations, Professional Papers, and Capstones

Every second, human skin processes over one million sensory signals while maintaining properties such as electrical conductivity, mechanical adaptability, and regenerative capability that surpass all synthetic materials. Contemporary bioelectronic devices prove inadequate when contacting skin surfaces due to poor adhesion and electrical contact issues that prevent effective sensing. Despite advancements in wearable and bioelectronic technologies, current devices face major drawbacks when interfacing with human skin, particularly in maintaining firm adhesion, conformability, and low-noise electrical signal acquisition.

This research focuses on the development of a biomimetic hydrogel-based interface for bioelectronic sensing. Specifically, a hybrid hydrogel system composed of polydopamine (PDA)- doped …

Recreating Fiber Recruitment With Fiber Recruitment Using Additive Manufacturing, Natalia D. Mciver

Biomedical Engineering ETDs

Injured ligaments are often repaired with tendon grafts which may over or under constrain the joint; there is a need for an artificial graft option with the mechanical properties of a native ligament. Crimped fibers within ligaments allow for recruitment which means the viscoelastic properties of stress relaxation and creep are not inversely related. A feasibility study using ACLs and large-scale crimp models to study viscoelasticity, led to an in-depth analysis of the scapholunate interosseous ligament. Using the Modified Kelvin spring-dashpot model, for describing viscoelasticity with a variable stiffness property (time dependent fiber recruitment), we defined the relationship between creep …