Biomechanical Engineering Commons^™

7lr-C Upper Limb Dancing Prosthetic, Victor Ochoa, Zoe Kelemen, Ged Mulingtapang, Marley Paltiel

Mechanical Engineering

Ella Wallis, a student at Cal Poly and performer in the Cal Poly Drag Club with a trans humeral upper limb difference, wants a prosthetic device that allows for a large range of motion and high degree of articulation to help them better dance in the style of voguing, allowing them to express themselves further while performing. The prosthetic arm is body-driven and relies on momentum to reposition. It attaches to the user through a harness, which is clipped to a socket with elastic straps to not impede the shoulder’s range of motion. The design contains urethane resin, aluminum, stainless …

Structure And Movement Design To Build A Functional Prosthetic Hand, John Campbell

Honors College Theses

This project aims to create a functional prosthetic hand that will improve upon the previous design for this project. The previous design included four fingers which were moved using a four-bar linkage and slider crank mechanism in combination with a linear actuator to move all four fingers in unison. Two servo motors were used to create an opposable thumb that could be used to grasp objects. Movement of the prosthetic hand was activated using a signal received from a myoelectric sensor. The goal of this project is to study this design and attempt to upgrade the prosthetic hand utilizing a …

Husky Hand: A Low-Cost Electro-Mechanical Prosthetic Arm For The Underprivileged, Adam Robert

Thinking Matters Symposium

A continuation of a low-cost prosthetic upper limb prototype design which was investigated in EGN 301. The prosthetic is specifically designed for the needs and requirements of under privileged individuals in the Dominican Republic with upper limb amputations. The project focuses on the creation of an open-source computer aided prosthetic hand/arm model. The design allows consumer-grade fused filament fabrication (FFF) 3-D printers to be used. The improved design allows for the integration of the PQ-12 linear actuator for grasp and finger control. This simplifies the assembly, while, also reducing the size and mass of the whole unit. Producing a low-cost …

A Solution For Overcoming Transradial Prosthetic Control Limitations With Additive Manufacturing And Modeling Techniques, Olivia Layne Santee

Graduate Theses, Dissertations, and Problem Reports (ETD)

Prosthetic limbs have aided in the restoration of both cosmetic and functional capabilities of the human hand; however, structural and control limitations hinder widespread adoption. One example of these limitations addressed in this study is the lack of wrist degrees of freedom (DOF) in robotic hands. Using the mechanical model-driven design, I developed a hand with cable-driven actuation of fingers and direct actuation of the wrist pronation-supination and flexion-extension DOFs. An inverse dynamic simulation determined torque requirements in common tasks manipulating a 1 kg mass with rotational speeds up to 60 deg/s, setting a minimum limitation of 0.76 Nm on …

Final Design Review Report: The Underdogs, Parker Johnson, Jack Montgomery, Katherine Thomas

Mechanical Engineering

Aspen is a three-legged dog with mobility issues from Berkeley, California. She was hit by a car and her rear left leg was amputated at the hip. Robin Swanson, Aspen's owner, and her friend, Audrey Beil, are the sponsors for this project. Jack Montgomery, Katherine Thomas, and Parker Johnson, “The Underdogs”, are tasked with helping Aspen regain some of her mobility and the ability to go on walks. Research was done into the problem by talking with the sponsors and looking into existing products, designs, and patents. This document, the Final Design Review Report, outlines the background information, problem specification, …

In The Pursuit Of Assistance: A Team's Desire To Not Let A Congenital Amputation Get In A Young Boy's Way, Carl Russell Iii, Gavin Loucks, Kirsten Wozniak

Purdue Journal of Service-Learning and International Engagement

EPICS is a service-learning design program run through Purdue University. It strives to teach students design skills through providing for individuals, communities, and organizations in the surrounding area while mirroring engineering industry standards. BME (Biomedical Engineering) is a team within EPICS that strives to serve community partners through biomedical applications. William Sevick is an elementary school student with a congenital arm amputation. William and his family have been working with the BME team for the past three years designing assistive devices with the purpose of improving his actions in daily life such as eating, playing games, and riding his bike.

Geometric Iteration Of A Knee Prosthetic And Static Stress-Bearing Capacity, Alexander Wheeler

Honors Program: Senior Projects (Public)

The purpose of this study was to improve a prosthetic knee model in terms of size, weight, and biocompatibility. Several tests were run to determine its effectiveness in supporting static and quasistatic loads. The positions in which these tests were run include static upright standing, static one-knee 90 degree kneeling, static squatting at maximum flexion, and quasistatic midstride. These simulations were conducted to find areas of high stress and strain. These patterns were used to determine the maximum body weight a physical prosthetic could support. The material used to create the prosthetic was changed from AISI 316 stainless steel to …

Surf Leg, Samantha Campbell, Oyundari Altansukh, Caroline Swanson, Kurtis Barth

Mechanical Engineering

The Surf Leg Prosthetic project team in conjunction with QL+ and Operation Surf designed a transtibial prosthetic to be used for surfing. The senior project team focused on the missions of QL+ and Operation Surf as they went through the design process during the 2018-2019 academic year. The problem solved was that a standard prosthetic for a transtibial amputee does not provide the flexibility in enough degrees of freedom for a user to squat and balance on a surfboard. The goal of this project was to create a device specifically designed to improve the user’s balance and control while surfing. …

Exoskeleton Leg Brace, Aaron Indermuhle, Magomed Kasumov, Cevat Bagcioglu, Lucas Battaglia

Williams Honors College, Honors Research Projects

This report details the design process of a lower limb exoskeleton leg brace for elderly people with walking disabilities or others with disabilities that limit mobility. While there are other similar products on the market, the general design can be improved and these improvements have been implemented into the design presented within. Among these improvements are progress in efficiency, weight, user comfort, and cost. The results of the study are the design of a novel leg brace that improves on existing designs in each of these areas.

Our design solution incorporates the use of a single leg brace with no …

Single Arm Recumbent Bicycle, Alexander Borsotti, Ryan Westermann, Sean Liston

Mechanical Engineering

The goal of this report is to outline and cover the scope of work for the Single Arm Recumbent Bicycle Senior Project. The report will give an introduction of the problem, a background of the existing research or products relating to our project, the objectives of our project, our project management plan, our final design, manufacturing, testing, our project management, and final recommendations for improving the final design. The team is being supported by the Quality of Life Program, a non-profit organization that works to improve the lives of those injured in duty while serving our nation.

Up until now, …

Optimization Of Prosthetic Hands: Utilizing Modularity To Improve Grip Force, Grasp, And Versatility, Jordan William Harris

UNLV Theses, Dissertations, Professional Papers, and Capstones

It has been demonstrated that although many varieties of upper limb prosthetics exist, commercially available prosthetics are outdated and unsatisfactory. Ineffectiveness and limitations have led to some prosthesis wearers having to own multiple devices, whereas others have given up on them entirely. Even though ample research has been conducted to design and test new hand designs, the industry appears to rest in an overall stagnated state.

It was proposed here, that one problem with prosthetic research is an excess of variables involved in testing, and therefore the improper application of the scientific method. It seems that each time a research …

Self-Powered Ankle Prosthetic, Corina M. Espelien, Kelsey Pietzsch, Anna Sullivan

Mechanical Engineering

Originating from QL+'s customer requirements, the main technical specifications were to have 80% physiological range of motion, elastic energy return, impact absorption, and no external power sources. Based on the background research conducted and the discussions with experts in the field, the project team decided to focus on designing a prosthetic that focused on plantarflexion and dorsiflexion for a more comfortable gait. The main components of the final design are a hydraulic shock absorber, cam, torsion springs, heel, stopper, and separated keel. The heel, front and back keels, and stopper were manufactured out of carbon fiber. The link, lever, attachment …

Nanocomposite Bioelectronics For Biopotential Enabled Prosthesis, Dong Sup Lee

Theses and Dissertations

Soft material-enabled electronics can demonstrate extreme mechanical flexibility and stretchability. Such compliant, comfortable electronics allow continuous, long-term measurement of biopotentials on the skin. Manufacturing of the stretchable electronic devices is enabled by the recent development combining materials transfer printing and microfabrication. However, the existing method using inorganic materials and multi-layered polymers requires long material preparation time and expensive processing cost due to the requirement of microfabrication tools and complicated transfer printing steps. Here, this study develops a new fabrication method of soft electronics via a micro-replica-molding technique, which allows fast production, multiple use, and low cost by avoiding microfabrication and …

Prosthetic Thermal Management Device, Garrett Dowd

Williams Honors College, Honors Research Projects

High temperatures in lower-limb prosthetics can lead to poor user skin conditions and mechanical slippage between the user’s limb and the prosthetic. This report presents an air-cooling device for a lower-limb prosthesis. This device’s purpose is to maintain a constant skin-prosthesis interface temperature. A compact heat sink and small fan were used to transfer the bio-heat to the ambient surroundings. By changing the power of the fan, the thermal resistance of the whole system can be adjusted to match various thermal loads and environmental temperatures. Heat pads were used to mimic the heat generation of a residual limb, and cooling …

Design And Development Of A Stair Ascension Assistive Device For Transfemoral Amputees, Casey Michael Barbarino

Master's Theses

Transfemoral amputees around the world experience increased difficulty in climbing stairs due to lack of muscle, balance, and other factors. The loss of a lower limb greatly diminishes the amount of natural force generation provided that is necessary to propel oneself up stairs. This study investigated possible solutions to the problem of stair ascension for transfemoral amputees by the means of designing and developing an externally attachable device to a prosthesis. The number of amputations from military service has greatly increased since 2008, which shows there is a clear need for assistive devices (Wenke, Krueger, & Ficke, 2012). With the …

Polygrasp: Reach; Myoelectric Prosthetic Hand Iteration, Devon Patrick Augustus, Mighells Blaed Deuel, Ian Noel Fraser, Nicholas Philip Moesser

Mechanical Engineering

Amputations are a common occurrence in soldiers returning home who have suffered the effects of IED and munitions explosions. For upper limb amputees, trans-radial amputations are the most common. Traditional hook devices do not offer an adequate level of normalcy for users, prompting the use of myoelectric devices. While current myoelectric devices do offer a more natural experience, they come with a host of other problems that makes their adoption by service personnel not desirable or not permitted by the VA. PolyGrasp Reach seeks to reduce weight and cost and improve performance. This addresses several of the issues with devices …

Challenger J Hockey Prosthesis Final Design Report, Ryan Bakker, Spencer Noe, Christopher Perkins

Mechanical Engineering

The content of this report is withheld as confidential. QL+ is the owner of the intellectual property created throughout the duration of this project. Dr. Tom Mase (mechanical engineering) maintains a full copy of the report and intends to disseminate it upon completion of the necessary intellectual property protection measures.