Biomechanical Engineering Commons^™

Characterization Of The Fatigue Threshold Behavior Of Uhmwpe, Bethany B. Smith, Anurag Roy, Robert O. Ritchie, Lisa A. Pruitt

Faculty Journal Articles

Ultra-high-molecular-weight-polyethylene (UHMWPE) has been the material of choice for bearings in total joint replacements (TJRs) for decades as a result of its excellent wear resistance, chemical inertness, energetic toughness, low friction, and biocompatibility. Utilization of this polymer in orthopedic devices requires oxidation, wear, and fatigue resistance. Balancing these important properties by tailoring processing techniques and modulating microstructural features has been an ongoing endeavor in the field. Research into the clinical applications of UHMWPE has primarily focused on the challenges of wear and oxidation while studies into the realm of fatigue have been more limited. Literature gaps exist in fully understanding …

Deciphering And Translating Bioinspired Structures For Engineering Materials Design Via Computational Modeling And Machine Learning, Zhangke Yang

All Dissertations

Nature has evolved extraordinary structural materials—such as nacre, bone, and the mantis shrimp’s dactyl club—that achieve remarkable combinations of strength, toughness, and impact resistance. These properties arise from sophisticated synergies between structure and composition. Inspired by these biological systems, this dissertation presents a comprehensive investigation into bioinspired materials, uncovering fundamental mechanisms and providing guidance on designing materials with superior mechanical properties.

This dissertation begins by examining the "brick-and-mortar" structure of nacre, which informs the design of layered polymer-graphene nanocomposite films. Using coarse-grained molecular dynamics simulations, I elucidate mechanisms of dynamic wave propagation and energy dissipation in these systems, providing critical …

Magnetic Nano And Micro Rods As Tools For Characterizing Materials Mechanical Properties: Fundamentals And Applications, Artis Brasovs

All Dissertations

The focus of this dissertation is insect blood (Hemolymph). Hemolymph is analyzed by taking a materials science approach. Rheological characterization of hemolymph has been performed for the first time. Owing to a minute amount of available material, a new protocol was established where Magnetic Rotational Spectroscopy (MRS) with ferromagnetic nanorods was employed. The challenge was examining the microliter droplets' viscosity in less than a few minutes. This challenge was successfully resolved.

Blood is critical for the insect's survival: after wounding, the insect has to seal the wound quickly, in a few minutes. As the mechanism of fast clotting has never …

Shape Memory Alloy Capsule Micropump For Drug Delivery Applications, Youssef Mohamed Kotb

Theses and Dissertations

Implantable drug delivery devices have many benefits over traditional drug administration techniques and have attracted a lot of attention in recent years. By delivering the medication directly to the tissue, they enable the use of larger localized concentrations, enhancing the efficacy of the treatment. Passive-release drug delivery systems, one of the various ways to provide medication, are great inventions. However, they cannot dispense the medication on demand since they are nonprogrammable. Therefore, active actuators are more advantageous in delivery applications. Smart material actuators, however, have greatly increased in popularity for manufacturing wearable and implantable micropumps due to their high energy …

Environment And Response Of 3d-Encapsulated Mesenchymal Stem Cells To Mechanical Loading, Augustus Greenwood

McKelvey School of Engineering Graduate Student Theses & Dissertations

This thesis explores the micromechanical environment induced when cyclically compressing hydrogels via finite element modeling and experimentally on the impact of loading on mesenchymal stem cells (MSCs) when encapsulated withing 3D hydrogel matrices. Degenerative joint diseases, characterized by cartilage degradation, present significant challenges due to cartilage's limited self-repair capacity. Innovative approaches, including stem cell-based therapies and engineered biomaterials, have emerged as promising strategies for cartilage repair and regeneration. This work specifically investigates the calibration of a bioreactor, the uniformity of load response across the hydrogel constructs via finite element modeling (FEM), and the stress response of MSCs subjected to various …

Generalizable Fugitive Carrier Method For 3d Printing Of Hydrogels, Hakan Arslan

Mechanical and Aerospace Engineering Dissertations - Archive

Hydrogels, with physical characteristics resembling biological soft tissues, hold great potential for bioinspired and biomedical applications. However, using them in additive manufacturing systems has challenges because of their poor mechanical and rheological properties. In response to these challenges, we introduce a fugitive carrier method, a novel and generalizable approach for materials incompatible with pneumatic-based extrusion three-dimensional (3D) printers. Our developed fugitive carrier method allows the 3D printing of a broad spectrum of hydrogel precursors with low viscosity while retaining their inherent properties. This technique has been successfully demonstrated by creating biomimetic structures with anisotropic and programmable systems utilizing temperature-sensitive hydrogel …

Insights Into The Characterization And Degradation Of Electrospun Polycaprolactone Scaffolds For Tissue Engineering Applications, Caleb B. Wells

Theses and Dissertations

Electrospun polymeric biodegradable scaffolds are essential in tissue engineering, particularly for Engineered Tissue Vascular Grafts (ETVGs), which promise advancements in treating coronary artery disease, peripheral arterial disease, congenital cardiovascular defects, and renal disease. These scaffolds present a solution to issues with autologous graft availability and durability. While large-diameter grafts in low-pressure environments have seen success, small-diameter grafts in high-flow scenarios remain challenging. Understanding polymeric scaffold degradation and behavior during incubation, especially under dynamic mechanical loading, is vital for clinical translation of small-caliber ETVGs.

This research focuses on characterizing the mechanical and microstructural properties of electrospun polycaprolactone (PCL) scaffolds and their …

Air-Jet Bioprinting Of Stem Cell-Encapsulated Alginate Micro-Droplets For Organoid Biomanufacturing, Mirabella B. Stump

Electronic Theses and Dissertations

Biomanufactured 3D-organoids show promise for modeling and treating various conditions, particularly insulin-dependent diabetes mellitus (type-1 diabetes). Pancreatic islet organoids serve as sustainable sources of insulin-producing β-cells, potentially restoring insulin regulation in patients and providing a long-term solution for diabetes. Hydrogel droplet printing is an emerging technique in regenerative medicine due to its advantageous tunability and biocompatibility; however, challenges of consistency, quality control, and scalability persist. To address these issues, we developed a novel air-jetting based droplet bioprinting system for the generation of monodispersed alginate micro-droplets. The objective of this project was to incorporate human induced pluripotent stem cells (hiPSCs) into …

Engineered Material Systems For Mimicking Tissue And Disease, Margrethe Ruding

McKelvey School of Engineering Graduate Student Theses & Dissertations

This thesis comprises two studies involving design and application of soft material systems. The goal of the first study was to design, fabricate, and characterize hydrogel lattice structures with consistent, controllable, anisotropic mechanical properties. Lattices, based on four types of unit cells (cubic, diamond, vintile, and Weaire-Phelan), were printed using stereolithography (SLA) of polyethylene glycol diacrylate (PEGDA). In order to create structural anisotropy in the lattices, unit cell design files were scaled in one direction by a factor of two in each layer and then printed. The mechanical properties of the scaled lattices were measured in shear and compression and …

Experimental Investigation Of The Performance Of A Hybrid Self-Healing System In Porous Asphalt Under Fatigue Loadings, Shi Xu, Liu Xueyan, Amir Tabakovic, Erik Schlangen

Articles

Self-healing asphalt, which is designed to achieve autonomic damage repair in asphalt pavement, offers a great life-extension prospect and therefore not only reduces pavement maintenance costs but also saves energy and reduces CO2 emissions. The combined asphalt self-healing system, incorporating both encapsulated rejuvenator and induction heating, can heal cracks with melted binder and aged binder rejuvenation, and the synergistic effect of the two technologies shows significant advantages in healing efficiency over the single self-healing method. This study explores the fatigue life extension prospect of the combined healing system in porous asphalt. To this aim, porous asphalt (PA) test specimens with …

Development Of Light Actuated Chemical Delivery Platform On A 2-D Array Of Micropore Structure, Hojjat Rostami Azmand, Hojjat Rostami Azmand

Dissertations and Theses

Localized chemical delivery plays an essential role in the fundamental information transfers within biological systems. Thus, the ability to mimic the natural chemical signal modulation would provide significant contributions to understand the functional signaling pathway of biological cells and develop new prosthetic devices for neurological disorders. In this paper, we demonstrate a light-controlled hydrogel platform that can be used for localized chemical delivery in a high spatial resolution. By utilizing the photothermal behavior of graphene-hydrogel composites confined within micron-sized fluidic channels, patterned light illumination creates the parallel and independent actuation of chemical release in a group of fluidic ports. The …

Development Of An Anatomically And Electrically Conductive Brain Phantom For Transcranial Magnetic Stimulation, Hamzah A. Magsood

Theses and Dissertations

Transcranial Magnetic Stimulation (TMS) is a non-invasive technique for diagnostics, prognostic, and treatments of various neurological diseases. However, the lack of anatomically realistic brain phantoms has made the experimental verification of stimulation strength in the form of induced electric fields/voltages in the brain tissues an impediment to developing new TMS coils, stimulators, and treatment protocols. There are significant technological, safety, and ethical limitations to test the potential TMS treatment procedures or develop enhancements and refine them on humans or animals. This work aims to bridge the gap by introducing and developing an innovative manufacturing and fabrications process to produce a …

Electrophoresis In Heterogeneous Hydrogels And Applications In Surface Patterning, Ning Ge

Theses and Dissertations--Mechanical and Aerospace Engineering

The creation of chemical micropatterns on surfaces makes it possible to add unique chemical functionality to surfaces, modifying properties such as wettability, or even adding the ability to selectively bind other molecules. The creation of biochemical surface patterning in particular is useful in a variety of fields including tissue engineering and highthroughput drug screening. There are many existing surface patterning techniques which focus on precise control over the patterned geometry, even down to submicron scale features, but they do not allow local control over chemical concentration. So the results are high resolution patterns with binary concentration. There are also existing …

Development Of A Sonically Powered Biodegradable Nanogenerator For Bone Regeneration, Avi S. Patel

University Scholar Projects

Background: Reconstruction of bone fractures and defects remains a big challenge in orthopedic surgery. While regenerative engineering has advanced the field greatly using a combination of biomaterial scaffolds and stem cells, one matter of difficulty is inducing osteogenesis in these cells. Recent works have shown electricity’s ability to promote osteogenesis in stem cell lines when seeded in bone scaffolds; however, typical electrical stimulators are either (a) externally housed and require overcomplex percutaneous wires be connected to the implanted scaffold or (b) implanted non-degradable devices which contain toxic batteries and require invasive removal surgeries.

Objective: Here, we establish a biodegradable, piezoelectric …

Development Of A Sonically Powered Biodegradable Nanogenerator For Bone Regeneration, Avi Patel

Honors Scholar Theses

Background: Reconstruction of bone fractures and defects remains a big challenge in orthopedic surgery. While regenerative engineering has advanced the field greatly using a combination of biomaterial scaffolds and stem cells, one matter of difficulty is inducing osteogenesis in these cells. Recent works have shown electricity’s ability to promote osteogenesis in stem cell lines when seeded in bone scaffolds; however, typical electrical stimulators are either (a) externally housed and require overcomplex percutaneous wires be connected to the implanted scaffold or (b) implanted non-degradable devices which contain toxic batteries and require invasive removal surgeries.

Objective: Here, we establish a biodegradable, piezoelectric …

Soft-Microrobotics: The Manipulation Of Alginate Artificial Cells, Samuel Sheckman

Mechanical Engineering Research Theses and Dissertations

In this work, the approach to the manipulation of alginate artificial cell soft-microrobots, both individually and in swarms is shown. Fabrication of these artificial cells were completed through centrifugation, producing large volumes of artificial cells, encapsulated with superparamagnetic iron oxide nanoparticles; these artificial cells can be then externally stimulated by an applied magnetic field. The construction of a Permeant Magnet Stage (PMS) was produced to manipulate the artificial cells individually and in swarms. The stage functionalizes the permanent magnet in the 2D xy-plane. Once the PMS was completed, Parallel self-assembly (Object Particle Computation) using swarms of artificial cells in complex …

Materials Design With Polylactic Acid-Polyethylene Glycol Blends Using 3d Printing And For Medical Applications., Jeremiah R. Bauer

Electronic Theses and Dissertations

This thesis is an examination of two material systems derived from polylactic acid (PLA) and polyethylene glycol (PEG). PLA is a polymer commonly sourced from renewable sources such as starches and sugars. It is a relatively strong, biodegradable polymer, making it ideal for use in the body. Even though it has a relative high strength, PLA is also brittle leading to the use of plasticizers to increase flexibility. One such plasticizer is PEG, which is a material that can exist at room temperature as either a thin liquid, or a hard waxy solid depending on the molecular weight. The first …

Bio Inspired Lightweight Composite Material Design For 3d Printing, Kaushik Thiyagarajan

Electronic Theses and Dissertations

Lightweight material design is an indispensable subject in product design. The lightweight material design has high strength to weight ratio which becomes a huge attraction and an area of exploration for the researchers as its application is wide and increasing even in every day-to-day product. Lightweight composite material design is achieved by selection of the cellular structure and its optimization. Cellular structure is used as it has wide multifunctional properties in addition to the lightweight characteristics. Applications of light weight cellular structures are wide and is witnessed in all industries from aerospace to automotive, construction to product design. In this …

Biomimetic Seal Flipper Test Rig, Gordon D. Belyea, Laura Kawashiri, Dylan Rinker, Kurt Beske

Mechanical Engineering

No abstract provided.

A Collagen‐Glycosaminoglycan‐Fibrin Scaffold For Heart Valve Tissue Engineering Applications, Claire Brougham, Stefan Jockenhoevel, Thomas Flanagan, Fergal O'Brien

Conference Papers

The field of heart valve biology and tissue engineering a heart valve continue to expand. The presentatio ns at this meeting reflect the advances made in both areas due to the multi-disciplinary approach taken by many laboratories.