Biomechanical Engineering Commons^™

Development And Validation Of A Human Knee Joint Finite Element Model For Tissue Stress And Strain Predictions During Exercise, Spencer D. Wangerin

Master's Theses

Osteoarthritis (OA) is a degenerative condition of cartilage and is the leading cost of disability in the United States. Motion analysis experiments in combination with knee-joint finite element (FE) analysis may be used to identify exercises that maintain knee-joint osteochondral (OC) loading at safe levels for patients at high-risk for knee OA, individuals with modest OC defects, or patients rehabilitating after surgical interventions. Therefore, a detailed total knee-joint FE model was developed by modifying open-source knee-joint geometries in order to predict OC tissue stress and strain during the stance phase of gait. The model was partially validated for predicting the …

Development And Validation Of A Human Hip Joint Finite Element Model For Tissue Stress And Strain Predictions During Gait, Jeffrey D. Pyle

Master's Theses

Articular cartilage degeneration, called osteoarthritis, in the hip joint is a serious condition that affects millions of individuals yearly, with limited clinical solutions available to prevent or slow progression of damage. Additionally, the effects of high-risk factors (e.g. obesity, soft and hard tissue injuries, abnormal joint alignment, amputations) on the progression of osteoarthritis are not fully understood. Therefore, the objective of this thesis is to generate a finite element model for predicting osteochondral tissue stress and strain in the human hip joint during gait, with a future goal of using this model in clinically relevant studies aimed at prevention, treatment, …

Advancement Of Legged Locomotion Models By Including Nonlinear Damping, Ian Abraham, Zhuohua H. Shen, Justin E. Seipel

The Summer Undergraduate Research Fellowship (SURF) Symposium

Accurately predicting human locomotion has been a goal of various mathematical models. Early canonical models of locomotion were developed to predict the basic features of ground reaction forces (GRF). More recently, modified hip actuated and leg damped locomotion models have been developed to better predict the stability and robustness of human and animal locomotion. Such improvements have resulted in the loss of the characteristic GRF predicted by earlier models. Historically, GRF are among the most common measures to experimentally study human locomotion. Thus, it is important to develop new mathematical models that predict both accurate stability of motion, as well …

Sequential Structural And Fluid Dynamics Analysis Of Balloon-Expandable Coronary Stents., David Martin

Doctoral

As in-stent restenosis following coronary stent deployment has been strongly linked with stent-induced arterial injury and altered vessel hemodynamics, the sequential numerical analysis of the mechanical and hemodynamic impact of stent deployment within a coronary artery is likely to provide an excellent indication of coronary stent performance. Despite this observation, very few numerical studies have considered both the mechanical and hemodynamic impact of stent deployment. In light of this observation, the aim of this research is to develop a robust numerical methodology for investigating the performance of balloon-expandable coronary stents in terms of their mechanical and hemodynamic impact within a …

Micro-Scale Dielectric Spectroscopy Of Biological Cells, Arindam Ghosh

Mechanical & Aerospace Engineering Theses & Dissertations

In recent years microfluidics has become one of the most commonly used tools to investigate cellular biology and to provide a platform for novel biomedical devices. Electrical Impedance Spectroscopy (EIS) was formulated as a non-invasive and label-fi.ee method to investigate the dielectric and the structural properties of materials. Since the early 20th century, EIS and Dielectric Spectroscopy have been applied to measure the dielectric properties of biological cells and tissues. Information about the cell membrane, cytoplasm and the nucleus can be extracted by dielectric spectroscopy. This thesis focuses on the applicability of the analytical models, in particular the Maxwell-Wagner Interfacial …

Water Removal From Gas Flow Channels Of Fuel Cells, Jeffrey S. Allen

Michigan Tech Patents

An apparatus for water management in a fuel cell. The apparatus includes a fuel cell having a first porous electrode layer, a second porous electrode layer, a proton-conducting membrane positioned between the first electrode and second electrode layers, and a first and second bi-polar distribution plate, wherein the first bi-polar distribution plate is positioned on a top of the first electrode layer and defining a first gas flow channel, and wherein the second bi-polar distribution plate is positioned on a bottom of the second electrode layer and defining a second gas flow channel. The apparatus further includes a mechanism for …

Measurement And Description Of Dynamics Required For In Vivo Surgical Robotics Via Kinematic Methods, Jacob G. Greenburg

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

With the goal of improved recovery times and reduced trauma to the patient there has been a substantial shift in the medical community’s demand for minimally invasive surgical (MIS) techniques. With the standardization of MIS becoming more commonplace in the medical field there are still many improvements that are desired. Traditional, manual methods of these surgeries require multiple incisions on the abdomen for the tools and instruments to be inserted. The more recent demand has been to localize the incisions into what is being referred to as a Laparoendoscopic Single-Site (LESS) surgery. Furthermore, the manual instruments that are commonly used …

Finite Element Models Of The Knee & Hip Joints: Using Opensim To Predict Muscle Forces, Kevin S. Jones, Spencer D. Wangerin, Jeffrey D. Pyle, Stephen M. Klisch, Scott J. Hazelwood

STAR Program Research Presentations

Quantitative data of stresses and strains in the cartilage of the knee and hip joints are required to design prostheses and can be used to give accurate advice to patients with cartilage damage as to which activities should be avoided. Instrumented hip implants can only give the overall resultant force in the joint, not the stresses and strains throughout the cartilage. Finite Element (FE) models of the Knee and Hip are being constructed in order to obtain the stresses and strains in articular (of the joint) cartilage. Muscle forces and joint contact forces are required as inputs to these FE …

Preliminary Development Of A Subject Specific Finite Element Model Of The Hindfoot, Liang Dong

Mechanical & Aerospace Engineering Theses & Dissertations

The human hindfoot is a complex structure and its medical treatment can vary from patient to patient. If physicians have access to a patient specific computer model, the optimal treatment option can be explored on the model before preforming it on the patient. The purpose of this study was to create a quasi-static finite element model and to show the stress contour in the cartilage between the bones. Ankle joint contact pressure was collected on one cadaver limb with a 40 lbs ( 178 N) axial load applied and tendon loads applied to simulate the ratio of tendon loading during …

Guidance System, Kayaking For The Visually Impaired, D. Ryan Kirtland, Ryan Phife, William Gardner, Amy Johnson

Biomedical Engineering

Quality Life Plus is working with Team River Runner to develop an assistive guidance system for veterans who want to remain active by kayaking, after sustaining an injury that impairs vision. This system allows these veterans to complete a slalom speed race independent of a personal guide in the water. The system incorporates 3 stations that each contain a speaker connected to a microcontroller system covered by a Pelican Case on a custom made buoy. During the slalom race, a kayaker will travel from shore towards buoy #1 as it omits sound from the speaker. As the kayaker moves around …

Evaluation Of Novel High-Density Emg Feedback Parameters On The Spatial Distribution Of Trapezius Muscle Activity, Brecca M. Gaffney

Electronic Theses and Dissertations

Each year, 17.9% of adults working in a computer-dominated work environment develop an episode of chronic neck and shoulder pain. An effective treatment method for chronic pain is postural correction through therapist. The understanding of the relation between cervicoscapular posture and trapezius muscle activity is not fully understood because the anatomy of the scapula is not accessible for direct observation. Until recently, the spatial distribution of trapezius muscle activity could not be measured due to the limitation in size of detection zone in traditional bipolar electrodes. The primary goal of postural correction when treating cases of chronic neck and shoulder …

Experimental Assessment Of The Impact Of Asymptomatic Gas Emboli On The Vessel Wall, Linxia Gu, Eric L. Cutler

Department of Mechanical and Materials Engineering: Faculty Publications

Quantitative evaluation of shear stress in the vessel wall due to the presence of asymptomatic gas emboli is lacking. The goal of this work was to assess the impact of chronic asymptomatic gas emboli on the risk of atherosclerosis through a custom-built cardiovascular flow simulator. Gas bubbles were created by forced air from a syringe pump. The influences of embolism injection rate, pulse rate, and time-averaged flow rate on the wall mean shear stress were investigated at resting and elevated heart rate conditions. The recorded pressure and volumetric flow rate from 24 experimental settings with four repetitions each were used …

Intuity Sleeve Redesign, Maxwell Arnold, Brittany Kinkade, Dominic Nicoletti

Mechanical Engineering

No abstract provided.

Adaptive Floor Hockey Device, Chris Gaul, Ricardo Gaytan, Matt Spaulding, Shannon Brant

Mechanical Engineering

Sean is a young boy living with ataxic cerebral palsy. Ataxic cerebral

palsy affects Sean’s balance and coordination, so he uses a walker to

increase his mobility. Sean would like to play Special Olympics Floor

Hockey but his walker prevents him from participating. The goal of this

Senior project was to develop a device to be attached to his previous

walker to allow Sean to play floor hockey in the least restrictive

environment possible. The Adaptive Floor Hockey Device is the product

we designed to satisfy this need.

Design And Development Of A Stair Ascension Assistive Device For Transfemoral Amputees, Casey Michael Barbarino

Master's Theses

Transfemoral amputees around the world experience increased difficulty in climbing stairs due to lack of muscle, balance, and other factors. The loss of a lower limb greatly diminishes the amount of natural force generation provided that is necessary to propel oneself up stairs. This study investigated possible solutions to the problem of stair ascension for transfemoral amputees by the means of designing and developing an externally attachable device to a prosthesis. The number of amputations from military service has greatly increased since 2008, which shows there is a clear need for assistive devices (Wenke, Krueger, & Ficke, 2012). With the …

Development Of A Pdms Based Micro Total Analysis System For Rapid Biomolecule Detection, Balaji Srinivasan Venkatesh

Graduate Theses and Dissertations

The emerging field of micro total analysis system powered by microfluidics is expected to revolutionize miniaturization and automation for point-of-care-testing systems which require quick, efficient and reproducible results. In the present study, a PDMS based micro total analysis system has been developed for rapid, multi-purpose, impedance based detection of biomolecules. The major components of the micro total analysis system include a micropump, micromixer, magnetic separator and interdigitated electrodes for impedance detection. Three designs of pneumatically actuated PDMS based micropumps were fabricated and tested. Based on the performance test results, one of the micropumps was selected for integration. The experimental results …

Design And Testing Of Novel Mouthguard With Intermediate Nitinol And Foam Layers, Adam Kessler

UNLV Theses, Dissertations, Professional Papers, and Capstones

It is the aim of this study to investigate a novel mouthguard design that incorporates the use of a nickel-titanium (Nitinol) layer and thin foam layer in addition to EVA layers. It is thought that the Nitinol layer can distribute the force of an impact and that the thin foam layer may absorb this distributed force better than a solid EVA mouthguard of the same thickness. Rectangular, flat coupons representative of several mouthguard configurations were constructed for testing using an instrumented drop-weight impact tower. The coupon configurations include a control made of laminated EVA, a group of laminated EVA and …

Closed Loop Control Of A Cylindrical Tube Type Ionic Polymer Metal Composite (Ipmc), Benjamin Mead

UNLV Theses, Dissertations, Professional Papers, and Capstones

The goal of this research is to provide a framework for the integration of tube type, cylindrical Ionic Polymer Metal-Composite (IPMC) into conventional devices. IPMCs are one of the most widely used types of electro-active polymer actuator, due to their low electric driving potential and large deformation range. For this research a tube type IPMC was investigated. This IPMC has a circular cross section with four separate electrodes on its surface and a hole through the middle. The four electrodes allow for biaxial bending and accurate control of the tip location. One of the main advantages of using this type …

Creating Standards Compliant Biodiesel Production Capability Using Waste Peanut Oil At Embry-Riddle Aeronautical University, Jintana Nina Phanthanousy

Doctoral Dissertations and Master's Theses

During the past year, Embry-Riddle Aeronautical University has been in the process of making a viable biodiesel using waste peanut oil from a Chick-Fil-A fast food restaurant on campus. Past research and biodiesel production from the previous two years on campus was taken into consideration and a catalyst change was proposed. Sample test batches were conducted to create a viable biodiesel and a consistent recipe. The biodiesel was tested for quality and also sent in for ASTM Standards testing. Biodiesel that passed quality testing would be permitted to be used as a B100 in campus facilities and university projects. It …

Mechanics Of Blast Loading On Post-Mortem Human And Surrogate Heads In The Study Of Traumatic Brain Injury (Tbi) Using Experimental And Computational Approaches, Shailesh Govind Ganpule

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Blast induced neurotrauma (BINT) has been designated as the “signature injury” to warfighters in the recent military conflicts. The occurrence of traumatic brain injury (TBI) in blasts is controversial in the medical and scientific communities because the manifesting symptoms occur without visible injuries. Whether the primary blast waves alone can cause mechanical insult that is comparable to existing traumatic brain injury thresholds is still an open question, and this work is aimed to address this issue.

In the first part of this dissertation, mechanics of primary blast loading on Realistic Explosive Dummy (RED) head with and without helmets is studied …

Valence-Length Correlations For Chemical Bonds From Atomic Orbital Exponents, F. D. Hardcastle

Journal of the Arkansas Academy of Science

Pauling’s empirical bond valence-length correlation has proven valuable because it offers a quick and convenient way of checking and evaluating molecular structures and determining oxidation states from measured bond lengths. In this study, a simplified quantum-mechanical approach was used to derive Pauling’s empirical bond valence-length relationship by considering overlap of hydrogen-like orbitals. An expression for the b “empirical” fitting parameter was derived in terms of atomic-orbital exponents. A new set of orbital exponents is presented using published atomic/covalent radii and a continuous function for the effective principal quantum. The b parameters calculated from the orbital exponents are consistent with bond …

Distal Placement Of An End-To-Side Bypass Graft Anastomosis: A 3d Computational Study, John Di Cicco, Ayodeji Demuren

Mechanical & Aerospace Engineering Faculty Publications

A three-dimensional (3D) computational fluid dynamics study of shear rates around distal end-to-side anastomoses has been conducted. Three 51% and three 75% cross-sectional area-reduced 6 mm cylinders were modeled each with a bypass cylinder attached at a 30-degree angle at different placements distal to the constriction. Steady, incompressible, Newtonian blood flow was assumed, and the full Reynolds-averaged Navier-Stokes equations, turbulent kinetic energy, and specific dissipation rate equations were solved on a locally structured multiblock mesh with hexahedral elements. Consequently, distal placement of an end-to-side bypass graft anastomosis was found to have an influence on the shear rate magnitudes. For the …

Ankle Impedance And Ankle Angles During Step Turn And Straight Walk: Implications For The Design Of A Steerable Ankle-Foot Prosthetic Robot, Evandro M. Ficanha

Dissertations, Master's Theses and Master's Reports - Open

During locomotion, turning is a common and recurring event which is largely neglected in the current state-of-the-art ankle-foot prostheses, forcing amputees to use different steering mechanisms for turning, compared to non-amputees. A better understanding of the complexities surrounding lower limb prostheses will lead to increased health and well-being of amputees. The aim of this research is to develop a steerable ankle-foot prosthesis that mimics the human ankle mechanical properties. Experiments were developed to estimate the mechanical impedance of the ankle and the ankles angles during straight walk and step turn. Next, this information was used in the design of a …

Cavitation In Pharmaceutical Manufacturing And Shipping, Donn Sederstrom

Electronic Theses and Dissertations

Therapeutic proteins are used to successfully treat hemophilia, Crohn's Disease, diabetes, and cancer. Recent product recalls have occurred because of sub-visible particle formation resulting from the inherent instability of proteins. It has been suggested that particle formation is associated with late stage processing steps of filling, shipping, and delivery. Previous work at the University of Denver demonstrated that fluid cavitation can generate a large number of sub-visible protein particles in ultra clean formulations, but that mitigation can be achieved with fluid property manipulation. The goal of this research was to (1) assess the risk of cavitation under common pharmaceutical manufacturing …

Biogeography-Based Optimization For Hydraulic Prosthetic Knee Control, Tim Wilmot, George Thomas, Berney Montavon, Rick Rarick, Antonie J. Van Den Bogert, Steve Szatmary, Daniel J. Simon, William Smith, Sergey Samorezov

Electrical and Computer Engineering Faculty Publications

We discuss open-loop control development and simulation results for a newly-developed cyber-physical system (CPS) used as a semi-active, above-knee prosthesis. The control signal of our CPS consists of two hydraulic valve settings that control a linear cylinder actuator and provide torque to the prosthetic knee. We develop open-loop control using biogeography-based optimization (BBO), which is a recently developed evolutionary algorithm. The research contributes to the field of cyber-physical systems by showing that it is possible to find effective open-loop control signals for our newly proposed semi-active hydraulic knee prosthesis through a dual-system optimization process which includes both human and robot …