Engineering Commons^™

High-Temperature Corrosion Testing Of Uranium Silicide Surrogates, B. J. Jaques, G. Alanko, D. P. Butt

Materials Science and Engineering Faculty Publications and Presentations

The corrosion resistance of cerium silicide, a surrogate of uranium silicide, is investigated to gain insight into the reaction of uranium silicide with water. As-received and proton-irradiated Ce₃Si₂, CeSi₂, and CeSi_1.x monolithic pellets are subjected to corrosion tests in water at 300°C and 9 MPa for up to 48 h. Results show that an oxide layer composed of Ce_4.67 (SiO₄)₃O forms on the surface of all samples, and it grows thicker with extended exposure times. Irradiated samples corrode to a greater extent than their unirradiated counterparts, which is …

Sample Preparation Techniques For Grain Boundary Characterization Of Annealed Triso-Coated Particles, M. L. Dunzik-Gougar, I. J. Van Rooyen, C. M. Hill, T. Trowbridge, J. Madden, J. Burns

Materials Science and Engineering Faculty Publications and Presentations

Crystallographic information about layers of silicon carbide (SiC) deposited by chemical vapor deposition is essential to understanding layer performance, especially when the the layers are in nonplanar geometries (e.g., spherical). Electron backscatter diffraction (EBSD) was used to analyze spherical SiC layers using a different sampling approach that applied focused ion beam (FIB) milling to avoid the negative impacts of traditional sample polishing and address the need for very small samples of irradiated materials for analysis. The mechanical and chemical grinding and polishing of sample surfaces can introduce lattice strain and result in the unequal removal of SiC and the surrounding …

Computer Software Release: Open Photo Roster, Szymon Machajewski

Open Teaching Tools

Learning student names in a classroom course is important to creating an inclusive learning environment. Some Learning Management Systems, like Blackboard Learn, provide tools for student images, but such tools are insufficient. This software project creates a consistent and reliable way of identifying students for the needs of proctored exams as well as for learning student names.

Laser Doppler Velocimetry Using A Modified Computer Mouse, Edward D. Zaron

Civil and Environmental Engineering Faculty Publications and Presentations

A computer mouse has been modified for use as a low-cost laser Doppler interferometer and used to measure the two-component fluid velocity of a flowing soap film. The mouse sensor contains two vertical cavity surface emitting lasers, photodiodes, and signal processing hardware integrated into a single package, approximately 1 cm2 in size, and interfaces to a host computer via a standard USB port. Using the principle of self-mixing interferometry, whereby laser light re-enters the laser cavity after being scattered from a moving target, the Doppler shift and velocity of scatterers dispersed in the flow are measured. Observations of the boundary …

On Phase Change Material Heat Exchangers: A Computational And Experimental Investigation, Christian Omar Rodriguez Dieppa

Theses and Dissertations

The emergence of ground- and airborne-based high energy laser (HEL) weapon systems has created a need for high-rate thermal energy storage (TES) devices that meet demanding size, weight, and power (SWaP) requirements for integration into the HEL thermal management system (TMS). Current and near-term HEL weapon systems produce thermal loads on the order of 30-300 kW when emitting, and approximately 5-10% of the peak load when in a non-emitting standby state. Emission to standby duty cycles of 10-50% are common, and therefore, sizing the TMS for real-time rejection of the peak thermal load is not practical. Accordingly, TES components can …

Direct Measurement Of Actual Levels Of Nitric Oxide (No) In Cell Culture Conditions Using Soluble No Donors, Weilue He, Megan C. Frost

Michigan Tech Publications, Part 1

Applying soluble nitric oxide (NO) donors is the most widely used method to expose cells of interest to exogenous NO. Because of the complex equilibria that exist between components in culture media, the donor compound and NO itself, it is very challenging to predict the dose and duration of NO cells actually experience. To determine the actual level of NO experienced by cells exposed to soluble NO donors, we developed the CellNO Trap, a device that allows continuous, real-time monitoring of the level of NO adherent cells produce and/or experience in culture without the need to alter cell culturing procedures. …

Selecting Effective Examples To Train Students For Peer Review Of Open‐Ended Problem Solutions, Matthew Verleger Dr., Kelsey J. Rodgers Dr., Heidi Diefes-Dux

Publications

Background Students conducting peer review on authentic artifacts require training. In the training studied here, individual students reviewed (score and provide feedback on) a randomly selected prototypical solution to a problem. Afterwards, they are shown a side-by-side comparison of their review and an expert’s review, along with prompts to reflect on the differences and similarities. Individuals were then assigned a peer team’s solution to review.

Purpose This paper explores how the characteristics of five different prototypical solutions used in training (and their associated expert evaluations) impacted students’ abilities to score peer teams’ solutions.

Design/Method An expert rater scored the prototypical …

Memristor-Based Volistor Gates Compute Logic With Low Power Consumption, Muayad Aljafar, Marek Perkowski

Electrical and Computer Engineering Faculty Publications and Presentations

We introduce a novel volistor logic gate which uses voltage as input and resistance as output. Volistors rely on the diode-like behavior of rectifying memristors. We show how to realize the first logic level, counted from the input, of any Boolean function with volistor gates in a memristive crossbar network. Unlike stateful logic, there is no need to store the inputs as resistances, and computation is performed directly. The fan-in and fan-out of volistor gates are large and different from traditional memristor circuits. Compared to solely memristive stateful logic, a combination of volistors and stateful inhibition gates can significantly reduce …

Simulation And Optimization Of Ant Colony Optimization Algorithm For The Stochiastic Uncapacitated Location-Allocation Problem, Jean-Paul Arnaout, Georges Arnaout, John El Khoury

Engineering Management & Systems Engineering Faculty Publications

This study proposes a novel methodology towards using ant colony optimization (ACO) with stochastic demand. In particular, an optimizationsimulation-optimization approach is used to solve the Stochastic uncapacitated location-allocation problem with an unknown number of facilities, and an objective of minimizing the fixed and transportation costs. ACO is modeled using discrete event simulation to capture the randomness of customers’ demand, and its objective is to optimize the costs. On the other hand, the simulated ACO’s parameters are also optimized to guarantee superior solutions. This approach’s performance is evaluated by comparing its solutions to the ones obtained using deterministic data. The results …

Pattern Reconfigurable Back-To-Back Microstrip Patch Antenna, Kansheng Yang, Xiulong Bao, Patrick Mcevoy, Max Ammann

Articles

A back-to- back microstrip patch antenna with a switchable pattern is proposed for WLAN applications. The patch elements, printed on FR-4 substrates with a common ground plane, are switched with a single-pole double-throw PIN diode circuit. Switching the feed selects either of two identical radiation patterns in the opposing hemispheres for spatial diversity that would benefit a distributed network.

Effects Of Auditory Vection Speed And Directional Congruence On Perceptions Of Visual Vection, Isabella Alexis Gagliano

Psychology Theses & Dissertations

Spatial disorientation is a major contributor to aircraft mishaps. One potential contributing factor is vection, an illusion of self-motion. Although vection is commonly thought of as a visual illusion, it can also be produced through audition. The purpose of the current experiment was to explore interactions between conflicting visual and auditory vection cues, specifically with regard to the speed and direction of rotation. The ultimate goal was to explore the extent to which aural vection could diminish or enhance the perception of visual vection. The study used a 3 × 2 within-groups factorial design. Participants were exposed to three levels …

Distributed Fiber-Optic Temperature Sensor Validations Using Field Deployments In The Flooded Orphan Boy Mine Shaft In Butte, Mt, Elliott Mazur

Graduate Theses & Non-Theses

The process of sensor validation through experimentation with the Omnisens Distributed Temperature and Strain (DITEST) Brillouin Optical Time Domain Analyzer (BOTDA) proved to be a challenging project. The project encompassed sensor calibrations, system error minimization, sensor network design and deployment, and the characterization of temperatures in the Orphan Boy Mine shaft. Fiber-optic cable sensor calibrations yielded linear relationship coefficients 0.6-1.0MHZ/°F, indicating a strong positive correlation between Brillouin Frequency Shifts and temperature. Calibrated sensors demonstrated accuracies near ±0.8°F using the corrected error bounds from residual analyses as the benchmark. Fiber-optic measurement accuracy and repeatability were controlled by user-selected signal interrogator settings …

Deposition Control For Electrospun Fibers, Joshua Beisel

Graduate Theses & Non-Theses

Electrospinning (ES) is a process for fabricating polymer fibers that have diameters that range from tens of nanons to hundreds of microns, which has been studied for over 100 years. These fibers have been studied in applications such as: the enhancement of mechanical properties including increased sensor sensitivity and increased tensile strength, filtration enhancement, drug delivery systems, and as a lithography masking material. In order to increase the effectiveness of ES, a real time feedback control mechanism to measure fiber diameters is needed. Currently only post-process methods of measuring fiber morphology, such as scanning electron microscopy or transmission electron microscopy, …

Computational Fluid Dynamics Study Of Molten Steel Flow Patterns And Particle-Wall Interactions Inside A Slide-Gate Nozzle By A Hybrid Turbulent Model, Mahdi Mohammadi-Ghaleni, Mohsen Asle Zaeem, Jeffrey D. Smith, Ronald J. O'Malley

Materials Science and Engineering Faculty Research & Creative Works

Melt flow patterns and turbulence inside a slide-gate throttled submerged entry nozzle (SEN) were studied using Detached–Eddy Simulation (DES) model, which is a combination of Reynolds–Averaged Navier–Stokes (RANS) and Large–Eddy Simulation (LES) models. The DES switching criterion between RANS and LES was investigated to closely reproduce the flow structures of low and high turbulence regions similar to RANS and LES simulations, respectively. The melt flow patterns inside the nozzle were determined by k–ε (a RANS model), LES, and DES turbulent models, and convergence studies were performed to ensure reliability of the results. Results showed that the DES model has significant …

Engineering Synthetic Feedback To Promote Recovery Of Self-Feeding Skills In People With Sensory Deficits Due To Stroke, Alexis Krueger

Master's Theses (2009 -)

Kinesthesia refers to sensations of limb position and movement, and deficits of upper limb kinesthetic feedback are common after stroke, impairing stroke survivors’ ability to perform the fundamental reaching and stabilization behaviors needed for daily functions like self-feeding. I attempt to mitigate the negative impact of post-stroke kinesthesia deficits by evaluating the utility of vibrotactile sensory substitution to restore closed-loop kinesthetic feedback of the upper limb. As a first step, this study evaluated performance in healthy individuals during fundamental reaching, stabilization, and tracking behaviors while using supplemental vibrotactile feedback encoding either limb state information or goal-aware error information. First, I …

Optimization Of The Bowtie Gap Geometry For A Maximum Electric Field Enhancement, Tsenguun Byambadorj

Master's Theses (2009 -)

Optimization of the geometry of a metallic bowtie gap at radio frequency is presented in this thesis. Since the design and fabrication of a plasmonic device (nanogap) at nanoscale is challenging, the results of this study can be used to estimate the best design parameters for nanogap structure. The geometry of the bowtie gap including gap size, tip width, metal thickness, and tip angle are investigated at macroscale to find the maximum electric field enhancement across the gap. This thesis focuses on the simulation portion of a work that consists of experimental and simulation platforms. The simulation platform is created …

Evaluation Of An Actuated Wrist Orthosis For Use In Assistive Upper Extremity Rehabilitation, Devon Holley

Master's Theses (2009 -)

Cerebral palsy (CP) is a neurological condition caused by damage to motor control centers of the brain. This leads to physical and cognitive deficiencies that can reduce an individual’s quality of life. Specifically, motor deficiencies of the upper extremity can make it difficult for an individual to complete everyday tasks, including eating, drinking, getting dressed, or combing their hair. Physical therapy, involving repetitive tasks, has been shown to be effective in training normal motion of the limb by invoking the neuroplasticity of the brain and its ability to adapt in order to facilitate motor learning. Creating a device for use …

Analysis Of Fatigue Crack Propagation In Welded Steels, Roberto Angelo Demarte

Master's Theses (2009 -)

This thesis presents the study of fatigue crack propagation in a low carbon steel (ASTM A36) and two different weld metals (AWS A5.18 and AWS A5.28). Fatigue crack propagation data for each weld wire is of interest because of its use for predicting and analyzing service failures. Fatigue crack growth test specimens were developed and fabricated for the low carbon steel base metal and for each weld wire. Weld specimens were stress relieved prior to fatigue testing. Specimens were tested on a closed-loop servo hydraulic test machine at two different load ratios. Fatigue test data was collected to characterize both …

Analysis Of Interference Between Electromagnetic Articulography And Electroglottograph Systems, Kelly Vonderhaar

Master's Theses (2009 -)

Electromagnetic Articulography (EMA) has become an integral tool for researchers and clinicians who seek to characterize speech kinematics. The position and orientation of the articulators – which include the jaw, lips, and tongue – are recorded by attaching sensors to the articulators and tracking the movement of the sensors through an electromagnetic field. This has been used by researchers and clinicians to better understand dysarthria and synthesize speech, among other applications. Another speech tool, electroglottography (EGG), is used to analyze the movement of the vocal folds during speech production. This is achieved by measuring the time variation of the contact …

Plasticized Polymer Coatings For Sh-Saw Sensors For High Sensitivity And Long-Term Monitoring Of Btex Analytes In Liquid Phase, Pintu Adhikari

Master's Theses (2009 -)

BTEX compounds (benzene, toluene, ethylbenzene, and xylene) are constituents of crude oil and hazardous to human health. Among them, benzene has the lowest maximum contaminant level for drinking water because of its carcinogenicity. Spills or leakage from underground storage tanks or hazardous waste sites can contaminate nearby groundwater with these volatile organic compounds. Therefore, it is very important to detect the presence of BTEX contamination as early as possible in order to start the remediation process and maintain a healthy environment. To develop an in-situ continuous monitoring sensor system, shear horizontal surface acoustic wave (SH-SAW) sensor devices are being investigated …

Effects Of Surrounding Water Table On A Forested Wetland Habitat In East Coast Of Virginia, Lane Stokes

Civil & Environmental Engineering Theses & Dissertations

Exchanges into and out of a wetland, including surface water flow, groundwater flow, and constituents in the flows, usually determine the wetland physicochemical characteristics and biodiversity. To date, of these three exchanges, groundwater flow is the least studied, particularly in the United States of America. In this thesis, field observations were conducted at a forested non-tidal wetland, located on a flat hilltop. The position of the wetland is such that groundwater outflow is the only significant exchange that could be impacted by the surrounding land use. In addition, a spatially variable steady-state model was set up to extrapolate the observations …

Parametric Investigation Of A Laboratory Drop Test To Simulate Base Acceleration Induced By Wave Impacts Of High Speed Planing Craft, John D. Barber

Mechanical & Aerospace Engineering Theses & Dissertations

High speed operations in a small craft can be physically punishing and, in some circumstances, even dangerous for the crew. The aspect of small craft operations that make them punishing for the crew is wave slamming generated by wave impacts as the craft is traveling over the seas at high speed.

The initial step of this thesis effort was to perform a literature survey to determine what knowledge existed within the technical and academic community about wave slamming and simulating them with drop tests.

Eventually, a final experiment strongly influenced by the experiment model found in (Protocol 1, 2014) was …

Longitudinal Tidal Dispersion Coefficient Estimation And Total Suspended Solids Transport Characterization In The James River, Beatriz Eugenia Patino

Civil & Environmental Engineering Theses & Dissertations

The longitudinal dispersion coefficient is a parameter used to evaluate the effect of cross-sectional variations on substance mixing mechanisms in estuaries influenced by tide, wind and internal density variations. Considering a two dimensional approach, this study aims at evaluating a tidal area of the lower James River at approximately 19 miles upstream from the mouth at the Chesapeake Bay, in the City of Newport News, and applies an experimental procedure based on in-situ salinity concentrations to estimate the dispersion coefficient in the area where receives a discharge from the HRSD James River Wastewater Treatment Plant, and further characterizes Total Suspended …

Testing And Analysis Of An Exergetically Efficient 4 K To 2 K Helium Heat Exchanger, Peter N. Knudsen

Mechanical & Aerospace Engineering Theses & Dissertations

Modern experimental nuclear physics programs that utilize advanced superconducting devices require refrigeration below the lambda temperature of helium (2.1768 K) and involve sub-atmospheric helium at some point in the process. They typically operate between 1.8 and 2.1 K (16 to 40 mbar) and can require refrigeration ranging from tens to thousands of watts. These processes are very energy intensive, requiring roughly 850 W/W even for large and well-designed refrigerators, though they can easily require much more. Adiabatic expansion of sub-cooled liquid helium to these sub-atmospheric pressures will result in a two-phase mixture with a large liquid to vapor density ratio. …

99mtc-Hexamethylpropyleneamine Oxime Imaging For Early Detection Of Acute Lung Injury In Rats Exposed To Hyperoxia Or Lipopolysaccharide Treatment, Said H. Audi, Anne V. Clough, Steven T. Haworth, Meetha Medhora, Mahsa Ranji, John C. Densmore, Elizabeth R. Jacobs

Biomedical Engineering Faculty Research and Publications

^99mTc-Hexamethylpropyleneamine oxime (HMPAO) is a clinical single-photon emission computed tomography biomarker of tissue oxidoreductive state. Our objective was to investigate whether HMPAO lung uptake can serve as a preclinical marker of lung injury in two well-established rat models of human acute lung injury (ALI).

Rats were exposed to >95% O₂ (hyperoxia) or treated with intratracheal lipopolysaccharide (LPS), with first endpoints obtained 24 h later. HMPAO was administered intravenously before and after treatment with the glutathione-depleting agent diethyl maleate (DEM), scintigraphy images were acquired, and HMPAO lung uptake was quantified from the images. We also measured breathing rates, heart …

Photoreceptor Inner Segment Morphology In Best Vitelliform Macular Dystrophy, Drew Scoles, Yusufu N. Sulai, Robert F. Cooper, Brian P. Higgins, Ryan D. Johnson, Joseph Carroll, Alfredo Dubra, Kimberly E. Stepien

Biomedical Engineering Faculty Research and Publications

PURPOSE

To characterize outer retina structure in best vitelliform macular dystrophy (BVMD) and to determine the effect of macular lesions on overlying and adjacent photoreceptors.

METHODS

Five individuals with BVMD were followed prospectively with spectral domain optical coherence tomography and confocal and nonconfocal split-detector adaptive optics scanning light ophthalmoscopy (AOSLO). The AOSLO cone photoreceptor mosaic images were obtained within and around retinal lesions. Cone density was measured inside and outside lesions. In 2 subjects, densities were compared with published measurements acquired ∼2.5 years before. One subject was imaged 3 times over a 5-month period.

RESULTS

The AOSLO imaging demonstrated that …

Repmatch: Robust Feature Matching And Pose For Reconstructing Modern Cities, Wen-Yan Lin, Siying Liu, Minh N. Do, Ping Tan, Jiangbo Lu

Research Collection School Of Computing and Information Systems

A perennial problem in recovering 3-D models from images is repeated structures common in modern cities. The problem can be traced to the feature matcher which needs to match less distinctive features (permitting wide-baselines and avoiding broken sequences), while simultaneously avoiding incorrect matching of ambiguous repeated features. To meet this need, we develop RepMatch, an epipolar guided (assumes predominately camera motion) feature matcher that accommodates both wide-baselines and repeated structures. RepMatch is based on using RANSAC to guide the training of match consistency curves for differentiating true and false matches. By considering the set of all nearest-neighbor matches, RepMatch can …

High-Level Multi-Objective Model For Microgrid Design, Siamak Talebi

Theses and Dissertations

Recently, there is vast inclination toward using renewable energy in rural areas away from the main electricity generation plants. Small airports located in rural areas are good candidates to apply sustainable energy for electrical power needs. Because of the intermittency of the renewable sources, it is important to have energy storage to guarantee an uninterrupted and stable power supply for end users. In this work, a high-level micro grid model is proposed considering making decisions about different factors such as different renewable sources capacity, storage and system capacity. A multi-objective model of a microgrid high-level design is used to formulate …

A Maximum Entropy Approach To Identifying Important Statistical Moments To Best-Represent Spray Distribution Data, Cheng Chen

Theses and Dissertations

To obtain accurate spray droplet size and velocity distributions, higher-order statistical moments are needed. The Maximum Entropy formalism has been successfully used to predict the motion of spray flow in different models. This work is mainly focused on the use of the fourth-order moment combinations to calculate droplet probability density functions using the Maximum Entropy Formalism. Beginning with the second-order moment combinations, Lagrange multipliers have been calculated subject to given moment constraints, defining the probability density function. All lower moments are included when calculating the possible different higher-order moment combinations. From the results, each moment combination generated a set of …

Angle Of Attack Visualization: A Proposal For A Tangible Interactive In-Flight Loss Of Control Recovery System, Nicholas Kasdaglis

Theses and Dissertations

The Trajectory Recovery System (TRS) is a proposed system that will help a pilot quickly restore the aircraft to controlled flight. In-flight Loss of Control (I-LOC) is the leading cause of aviation fatalities. While attempts to address this threat have mainly focused upon prevention and avoidance, there has been little offered for recovery from an I-LOC event. The work presented herein addresses this gap. Offered here will be a Human- Centered Design (HCD) solution to the problem of I-LOC. The TRS is a real-world application arising from robust multi-agent models of human-automation teaming. The use of such models transforms cognitive …