Engineering Commons^™

Query Expansion Techniques For Enterprise Search, Eric M. Domke

Masters Theses

Although web search remains an active research area, interest in enterprise search has waned. This is despite the fact that the market for enterprise search applications is expected to triple within the next six years, and that knowledge workers spend an average of 1.6 to 2.5 hours each day searching for information. To improve search relevancy, and hence reduce this time, an enterprise- focused application must be able to handle the unique queries and constraints of the enterprise environment. The goal of this thesis research was to develop, implement, and study query expansion techniques that are most effective at improving …

Sex Differences In Collateral Remodeling Following Hindlimb Arterial Occlusion, Laura Burckhardt

Master's Theses

Clinical evidence indicates a higher incidence of peripheral arterial occlusive disease and associated likelihood of critical limb ischemia in women, as well as worse prognosis and decreased survival post myocardial infarction. Therefore, understanding the possible differences in underlying vascular compensation mechanisms is crucial. With arterial occlusions, necrosis and tissue injury can be naturally mitigated by the collateral circulation, improving patient prognosis. Previous sex-comparison studies describing differences in vascular remodeling are inconsistent. Therefore, the aim of this study was to describe the effect of arterial occlusion on collateral remodeling in healthy male and healthy reproductive-stage female mice. At 7 days following …

Higher Education On Buildings: Case Study In The North Dakota Region, Houjun Yang, Malini Srivastava, Yanmei Xie, Yong Bai

Civil and Environmental Engineering Faculty Research and Publications

Because of the growing demand for local skilled professionals to improve the health, energy efficiency, and sustainability of residential and commercial buildings in North Dakota, this case study reports the current situation of higher education relating to buildings in the state’s vicinity, including Minnesota, Montana, North Dakota, and South Dakota. In this region, 116 programs relating to buildings were found in 41 postsecondary institutions, and both their majors and courses were then studied with frequency lists. The frequency information was analyzed over nine sets of curriculum areas at both graduate and undergraduate levels for the four states. After the current …

Deep Well Pump Seal, Peter M. Gordon, Matt C. Johnson, Dylan A. Smith

Mechanical Engineering

Lifewater International, a Christian non-profit, trains locals to repair water well hand pumps in various third world countries. It would be beneficial to retrofit difficult-to-repair hand pumps with a locally-made pump cylinder such as HydroMission's "SlapShot". The majority of the components in the "SlapShot" can be easily obtained in rural third world villages. However, the thick leather gaskets required to seal the water cylinder during the pumping operation are imported. These thick leather gaskets are expensive, and when they fail, this results in pumps being out of commission for extended periods of time. Lifewater has presented this problem to a …

Dyno-Mite Redesign, Brandon Joseph Miller, Daniel Robert Hoffman, Richard Demedici Young

Mechanical Engineering

The Cal Poly Mechanical Control Systems Laboratory currently employs an outdated device, known as the Motomatic, to teach students about various motor characteristics and control methods. These include open-loop vs. closed-loop control, speed vs. position control, and DC motor response curves. The current device does not function properly and produces unreliable data due to overwhelming non-linear effects such as stiction and shaft misalignment. Our team was tasked with designing a replacement device that retains many of the same educational goals as the original lab procedure, while also adding new educational goals pertaining to the device system dynamics. The new apparatus, …

Rogue Rotary - Modular Robotic Rotary Joint Design, Sean Wesley Murphy, Tyler David Riessen, Jacob Mark Triplett

Mechanical Engineering

This paper describes the design process from ideation to test validation for a singular robotic joint to be configured into a myriad of system level of robots.

Poly Spotlight Control, Ryan P. O'Neill, C. Oleg Frandle, Anthony T. Lombardi

Mechanical Engineering

When this project began, The Cambria Center for the Arts Theater used a manually-operated spotlight. The sound created by the fans, along with the sheer size of the spotlight, required that it be housed in an attic room above the theater and shined through a closed window. This trapped a lot of heat in the room and involved some risk with climbing into and out of the attic room. This project sought to remedy those issues by mounting a pair of newer LED spotlights inside the theater. Doing this required a method for remotely controlling and actuating the angular position …

An Analysis Of The Size And Impact Of Digital Footprints, Whitney Nielsen Maxwell

Theses and Dissertations

Personal information available online is known as a digital footprint. While many have a digital footprint, few if any, know what it encapsulates or how to control it. Technology and personal information are becoming more intertwined as technology becomes more integrated with everyday activities. Personal information can be defined as details that apply to a person such as race or shopping habits. Shopping habits are considered personal information by many corporations who spend money to track, or even predict purchases of individuals, whereas more traditional forms of personal information are details like gender, birthdate, and home town. With a wide …

Project Management: Skills, Tools, And Knowledge Construction Professionals Consider Important For Keeping Projects On Schedule, Lyle Scott Davies

Theses and Dissertations

Project managers have a major role in the construction and completion of projects. Much of their work consists of reviewing, clarifying, and coordinating information required by the field management and subcontractors performing the work on the job site. The assistance they give with the transfer of information helps with successfully completing projects. For many people, the largest indicator that a project was successful is that construction activities were completed on schedule. While finishing on schedule may be the primary focus of those involved with construction activities, projects still struggle to finish on time. The purpose of this study is to …

Advancements In Radio Astronomical Array Processing: Digital Back End Development And Interferometric Array Interference Mitigation, Mitchell Costus Burnett

Theses and Dissertations

The Brigham Young University (BYU) Radio Astronomy Systems group, in collaboration with the National Radio Astronomy Observatory (NRAO), the Center for Astrophysics at West Virginia University (WVU), and the Green Bank Observatory (GBO) have developed, and commissioned, a broadband real-time digital back end processing system for a 38-element phased array feed (PAF) with 150 MHz of instantaneous bandwidth. This system is capable of producing coarse and fine channel correlations, and implements a real-time beamformer that forms 7 simultaneous dual-polarized beams. This thesis outlines the hardware and software development for the digital back end and presents on-telescope commissioning results. This system …

Investigating If Multidisciplinary Or Homogenous Teams Are More Innovative In A Higher Education Setting, Blake Howard Hoover

Theses and Dissertations

This study is derived from the claim that multidisciplinary groups are more innovative than homogeneous groups; a claim that has flooded the business industry and has become criteria for accreditation in higher education. However, the impact of disciplinary diversity in work groups is a growing area of research; therefore, it is yet to be thoroughly understood. The purpose of this study is to answer the question: are multidisciplinary teams more innovative than homogenous teams. To accomplish this university students from differing majors were sorted into multidisciplinary and homogeneous groups while participating in a two-day innovation course. The course taught the …

Analysis Of Safety Impacts Of Access Management Alternatives Using The Surrogate Safety Assessment Model, Kyung Min Kim

Theses and Dissertations

In a traditional safety impact analysis, it is necessary to have crash data on existing roadway conditions in the field and a few years must pass before accumulating reliable crash data. This is a time-consuming approach and there remains uncertainty in the crash data due to the random nature of crash occurrences. The Surrogate Safety Assessment Model (SSAM) was developed for resolving these issues. With SSAM, a conflict analysis is performed in a simulated environment. A planned improvement alternative under study is modeled and no physical installation of the alternative is needed. Hence, the method using a simulation software along …

Tribopairs In Wellbore Drilling: A Study Of Pcd Tilting Pad Bearings In An Electric Submersible Pump, Cameron B. Ellis

Theses and Dissertations

A polycrystalline diamond was tested as a bearing material for a tilting pad thrust bearing to be used in an electric submersible pump, which elevates process fluids from the bottom of well bores. The goal of this study was to compare the PCD to a current best of technology, which is stainless steel with an engineering polymer.This study found that PCD can handle larger loads than current technology but is limited in size due to diamond sintering and manufacturing constraints. The maximum size is Ø75mm.

An Investigation Of Elementary Teachers<'> Self-Efficacy For And Beliefs About The Importance Of Engineering Education, Khristen Lee Massic

Theses and Dissertations

In order for the United States to regain its global standing in science and engineering, educational and governmental organizations have started to re-emphasize science, technology, engineering, and math content in k-12 classrooms.While some preliminary research has been conducted on student and teacher perceptions related to engineering, there has been little research conducted related to teachers beliefs about the importance of engineering content in their classrooms and relatively few studies have investigated elementary teachers teaching engineering self-efficacy. Current studies have investigated the impact of professional development on teachers teaching engineering self-efficacy but these studies were conducted with limited sample sizes, for …

Coorstek- Spine Discectomy, Rhett Prestwich, Logan Bolingbroke, Ryan Thomsen, Aaron Blanchard, Kayla Park

Undergraduate Honors Capstone Projects

The objective is to design improved instrumentation for performing a spine discectomy. In particular, the instrument should remove the nucleus pulposus without damaging the annulus in order to prepare the spine disc for the insertion of an artificial spacer. As more nucleus pulposus is removed from the disc, the spine will fuse more quickly and completely after the artificial spacer is inserted. The current process involves removing the nucleus pulposus piece by piece with pituitary rongeurs. This process is slow and often incomplete.

Determination Of Safe Ballasts For Anchoring Event Tents By Finite Element Analysis, Sandeep Manoharan

All Theses

Event tents are large structures made of fabric covers attached to a structural frame and poles. Every year, many temporarily installed tents are subjected to large wind conditions that lead to sliding or lift of the frame due to improper anchoring to the ground. When ballasted, as opposed to anchored using stakes that penetrate the ground, non-certified tents are generally installed without proper analysis of sufficient ballast weights, which results into tent movements and lack of safety. The objective of this thesis is to determine load factors for non-certified tents affected by high wind loads. The load requirements (load factors) …

Me-Em Enewsbrief, July-December 2017, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Methodologies For Solving Integrated Transportation And Scheduling Problems, Fereydoun Adbesh

Graduate Theses and Dissertations

This research proposes novel solution techniques to optimize two real-world problems in the area of scheduling and transportation. We first consider a model for optimizing the operations of dredges. In this problem, scheduling and assignment decisions are integrated across a finite planning horizon. Additional constraints and problem elements explicitly considered include, but are not limited, to environmental work window restrictions, budget limitations, dredge operation rates and schedule-dependent dredge availability. Our approach makes use of Constraint Programming (CP) to obtain quality and robust solutions within an amount of time small enough to be useful to practitioners. The expanded feature set of …

A Comparison Of Two Innovation Tools: Application On Smart Kitchen Design, Burcu Taşkın

Electrical and Computer Engineering Faculty Publications and Presentations

The process is one of the significant issues of companies in innovative product design. The designers and the management deal with producing high quality products with the creativity in a short-term period. The researchers developed techniques to solve that problem as TRIZ. The TRIZ-based techniques aim to recover the gaps of the creative innovation to solve specific problems of technical products and technologies. However, the traditional innovation techniques are still preferred for the design process. This study conducted a comparative research on outcomes regarding the process of two design groups. The assignment is given to ten design students to identify …

Mining Electrical Meter Data To Predict Principal Building Use, Performance Class, And Operations Strategy For Hundreds Of Non-Residential Buildings, Clayton Miller, Forrest Meggers

Research Collection College of Integrative Studies

This study focuses on the inference of characteristic data from a data set of 507 non-residential buildings. A two-step framework is presented that extracts statistical, model-based, and pattern-based behavior. The goal of the framework is to reduce the expert intervention needed to utilize measured raw data in order to infer information such as building use type, performance class, and operational behavior. The first step is temporal feature extraction, which utilizes a library of data mining techniques to filter various phenomenon from the raw data. This step transforms quantitative raw data into qualitative categories that are presented in heat map visualizations …

Measurement Of Peptoid Concentration Using Uv Spectroscopy, Katie Holland

Chemical Engineering Undergraduate Honors Theses

The goal of this research is to establish a relationship between ultraviolet adsorption and peptiod concentration to be used to determine the concentration of an unknown peptoid sample. This will allow for the measurement of concentration differences of peptoid samples before and after incubation with membrane surfaces. Samples were prepared nine know concentrations and diluted 50 fold. The UV absorbances of each sample was measured using a UV spectrophotometer at wavelengths from 200 to 450 nanometers. This process was repeated, and the maximum absorbance of each replicate was averaged to yield an absorbance value for each concentration of peptoid. …

A Risk-Based Method For Estimating The Carbon Sequestration Budget For A Mixed Hardwood Forest, Erin Cooper

Chemical Engineering Undergraduate Honors Theses

Carbon Dioxide (CO₂) levels in the atmosphere have risen from approximately 310 ppm in the 1950’s to over 400 ppm as of 2015. This rise in CO₂ has likely resulted in the observed warming trend of the earth’s atmosphere in the same time frame, causing significant concern in the scientific community. Several mitigation strategies have arisen to combat the upward trend of CO₂ emissions in recent decades, among them being carbon sequestration- the process of capturing CO₂ from the atmosphere and holding it for an extended period of time. This study used the U.S. Forest …

Coupling K-12 Music Education With Science, Technology, Engineering And Math (Stem) Curricula: Implementation Of A Stemusic Outreach Program, Mallory Maestri

Civil Engineering Undergraduate Honors Theses

Many studies have investigated the effects of music on evoking human emotions and diverse types of brain responses. One study by Juslin and Vastfjall indicates that hearing music can stimulate brain stem reflexes, create emotional contagion, recall episodic memories and provoke visual imagery. Due to the influence music has on human brain waves, researchers have been studying the effect of music on enhancing the spatial abilities of young students. Science, Technology, Engineering and Math (STEM) professions rely heavily on spatial skills. Research on the connection of music with spatial skills proposes that when the brain processes rhythm a “mental rotation” …

Development Of A Multiphase Photon Monte Carlo Method For Spray Combustion And Its Application In High-Pressure Conditions, Somesh Roy, Jian Cai, Michael F. Modest

Mechanical Engineering Faculty Research and Publications

In this work the development of a multiphase photon Monte Carlo (PMC) method with a focus on resolving radiative heat transfer in combustion simulations is presented. The multiphase PMC solver can account for description of participating media in both Lagrangian and Eulerian frameworks. The solver is validated against exact solutions in several one-dimensional configurations. The developed solver is then applied to Diesel spray combustions, where liquid spray droplets are assumed to be cold, nonemitting, large, and isotropically scattering. Several formulations for radiative properties of the Diesel spray are first explored. The PMC solver has then been coupled with the multiphase …

Development Of A Rotordynamic Signal Processing Matlab Interface And A Two-Disk Rotor Model, David L. Baker

Master's Theses

Using MATLAB and a National Instruments data acquisition card, a signal processing program meant to monitor the behavior of rotordynamic systems in real-time was developed and tested. By using traditional analysis methods in this field of engineering, commonly desired data representations such as bode, polar, orbit, full spectrum plots were able to be produced to a very high accuracy. Additional capabilities offered by this application are slow roll compensation, synchronous and sub-synchronous filtering, and true three dimensional plotting. The verification of this program was done by comparing the results to the ones acquired with Bently Nevada’s “Automated Diagnostics for Rotating …

Genealogy Extraction And Tree Generation From Free Form Text, Timothy Sui-Tim Chu

Master's Theses

Genealogical records play a crucial role in helping people to discover their lineage and to understand where they come from. They provide a way for people to celebrate their heritage and to possibly reconnect with family they had never considered. However, genealogical records are hard to come by for ordinary people since their information is not always well established in known databases. There often is free form text that describes a person’s life, but this must be manually read in order to extract the relevant genealogical information. In addition, multiple texts may have to be read in order to create …

Sd-Mcan: A Software-Defined Solution For Ip Mobility In Campus Area Networks, Adam Chase Calabrigo

Master's Theses

Campus Area Networks (CANs) are a subset of enterprise networks, comprised of a network core connecting multiple Local Area Networks (LANs) across a college campus. Traditionally, hosts connect to the CAN via a single point of attachment; however, the past decade has seen the employment of mobile computing rise dramatically. Mobile devices must obtain new Internet Protocol (IP) addresses at each LAN as they migrate, wasting address space and disrupting host services. To prevent these issues, modern CANs should support IP mobility: allowing devices to keep a single IP address as they migrate between LANs with low-latency handoffs. Traditional approaches …

Smart Dc/Dc Wall Plug Design For The Dc House Project, Richard Sinclair Liu

Master's Theses

The present day duplex wall receptacle in the United States provides 120Vrms AC at 60Hz, which comes from a standard set for AC loads by the National Electrical Manufacturers Association. With a DC system, such as what is used in the DC House project currently being developed at Cal Poly, providing DC power to DC loads presents a technical challenge due to the different required DC operating voltages of the loads. This thesis entails the design and construction of a Smart DC/DC Wall Plug, which can automatically adjust its output voltage to match any required DC load voltages. In the …

Computer-Aided Diagnoses (Cad) System: An Artificial Neural Network Approach To Mri Analysis And Diagnosis Of Alzheimer's Disease (Ad), Berizohar Padilla Cerezo

Master's Theses

Alzheimer’s disease (AD) is a chronic and progressive, irreversible syndrome that deteriorates the cognitive functions. Official death certificates of 2013 reported 84,767 deaths from Alzheimer’s disease, making it the 6th leading cause of death in the United States. The rate of AD is estimated to double by 2050. The neurodegeneration of AD occurs decades before symptoms of dementia are evident. Therefore, having an efficient methodology for the early and proper diagnosis can lead to more effective treatments.

Neuroimaging techniques such as magnetic resonance imaging (MRI) can detect changes in the brain of living subjects. Moreover, medical imaging techniques are the …

A Comparison Study Of Composite Laminated Plates With Holes Under Tension, Joun S. Kim

Master's Theses

A Comparison Study of Composite Laminated Plates with Holes under Tension

A study was conducted to quantify the accuracy of numerical approximations to deem sufficiency in validating structural composite design, thus minimizing, or even eliminating the need for experimental test. Error values for stress and strain were compared between Finite Element Analysis (FEA) and analytical (Classical Laminated Plate Theory), and FEA and experimental tensile test for two composite plate designs under tension: a cross-ply composite plate design of [(0/90)4]s, and a quasi-isotropic layup design of [02/+45/-45/902]s, each with a single, centered hole of 1/8” diameter, and 1/4" diameter (four sets …