Engineering Commons^™

Permeable Concrete Barriers To Control Water Pollution: A Review, Rehab O. Abdel Rahman, Ahmed M. El-Kamash, Yung-Tse Hung

Civil and Environmental Engineering Faculty Publications

Permeable concrete is a class of materials that has long been tested and implemented to control water pollution. Its application in low-impact development practices has proved its efficiency in mitigating some of the impacts of urbanization on the environment, including urban heat islands, attenuation of flashfloods, and reduction of transportation-related noise. Additionally, several research efforts have been directed at the dissemination of these materials for controlling pollution via their use as permeable reactive barriers, as well as their use in the treatment of waste water and water purification. This work is focused on the potential use of these materials as …

Shallow‑Water Habitat In The Lower Columbia River Estuary: A Highly Altered System, Will Templeton, David A. Jay, Heida Diefenderfer, Stefan Talke

Civil and Environmental Engineering Faculty Publications and Presentations

Decreases in shallow-water habitat area (SWHA) in the Lower Columbia River and Estuary (LCRE) have adversely affected salmonid populations. We investigate the causes by hindcasting SWHA from 1928 to 2004, system-wide, based on daily higher high water (HHW) and system hypsometry. Physics-based regression models are used to represent HHW along the system as a function of river inflow, tides, and coastal processes, and hypsometry is used to estimate the associated SWHA. Scenario modeling is employed to attribute SWHA losses to levees, flow regulation, diversion, navigational development, and climate-induced hydrologic change, for subsidence scenarios of up to 2 m, and for …

An Energy-Efficient Pumping System For Sustainable Cities And Society: Optimization, Mathematical Modeling, And, Impact Assessment, Md S. Hossain, Mohammad R. Islam, Arnob Das, Hasibul H. Himel, Barun K. Das, Tamal K. Roy, Md S. Hasan

Research outputs 2022 to 2026

In this research work, we have focused on one of the reasons called drawdown (difference between static and pumping heads) for getting maximum efficiency. Therefore, various mechanical attachments have been designed and fabricated for performance evaluation. Since pump performance and drawdown are inversely related, the primary goal is to reduce drawdown as much as possible. The effect of various types of mechanical attachments on pump performance is investigated in this research work. Three bowl-type mechanical attachments can be integrated at once and can increase efficiency by up to 58%, which is 8% more than utilizing no attachment. Additionally, the impact …

Designing For A Local Brand Image Of Architecture To Achieve Cultural Sustainability: Al Ain City As A Case Study, Dana Bassam Bidoun

Theses

Cities, like Al Ain, are dynamic entities, echoing the diverse rhythms and values of their inhabitants. Urban evolution showcases a city's brand-its unique identity sculpted by historical, cultural, and local influences. A city's true essence emerges when architects collaborate with residents, blending their desires with the city's architectural legacy. This study aimed to evaluate the effectiveness of a brand-based design strategy, integrating the architecture process with insights from local residents to foster a sense of identity and belonging in the built environment. Grounded in the personal construct theory, the research applied the repertory grid technique, combining both qualitative and quantitative …

Development Of A Vortex-Cooled Bipropellant Thruster And Evaluation Of Performance Characteristics With Respect To Injection Parameters, Mousa Adnan Aqailan

Theses

This study presents an experimental assessment of the cooling performance and efficiency of a 10N-vortex-cooled Propane/Gox bi-propellant thruster that was fabricated using metal and thermoplastic material. The proposal of injecting an oxidizer in a vortex pattern was suggested as a potential cooling method for semi-thermoplastic constructed thrust engines. This method has been demonstrated as a promising candidate for integrated cooling and can be manufactured using 3D printing technology. In contrast to typical complicated cooling systems and their attributed common downsides; the vortex injection can be 3D printed as a single solid piece thruster, thereby reducing design complexity, weight, and manufacturing …

Electromagnetic Mems Safety And Arming Devices, Fatima Rashed Alnuaimi

Theses

This thesis aims to investigate the design of safety and arming devices within artillery fuzes, which rely on the spin velocity and setback acceleration of the weapon. These systems consist of two critical components: the spin lock and the inertia lock. The spin velocity and setback acceleration of the weapon induce deformations in these components, serving as key criteria for determining whether the weapon is in an armed or safe state.

The primary objective of this thesis is to comprehensively analyze and assess the design of both the spin lock and inertia lock. The research will delve into multiple factors …

Development Of Popcorn Thermal Insulation Panels, Yonis Hussein Mohamud

Theses

The research and development of sustainable and renewable materials that can take the place of conventional plastics derived from petroleum has attracted increasing attention in recent years. Polylactic acid (PLA) and Polyhydroxy butyrate (PHB) are viable alternatives biopolymers due to their biodegradability. Also, the enhancement of material properties can be achieved through the incorporation of fillers. In this study, the utilization of popcorn in developing of insulation materials has been employed in two distinct methodologies. The first involves the coating of popcorn with varying percentages of PLA using the solvent casting method, while the second involves the integration of popcorn …

Design And Fem Modelling Of Mems Capacitive Accelerometer And Gyroscope For Quadcopter/Uav Applications, Shaikha Rashid Alnaqbi

Theses

This study presents the design, simulation, and analysis of Micro Electromechanical Systems (MEMS) sensors, constituting the principal components of MEMS-based Inertial Measurement Units (IMUs). The main objective of the study is to design, simulate and analyze 3-axis capacitive accelerometer and 3-axis gyroscope. The MEMS-based capacitive accelerometers and gyroscope are analyzed using Ansys Workbench. Modal, Static Structural and harmonic analysis are used to obtain resonant frequencies, deformation/stress and profile of amplitude over a wide range of frequencies. Mechanical sensitivity analysis of the designed accelerometer and gyroscope is performed using the Finite Element Method (FEM). Analytical Equations are developed to calculate mechanical …

Experimental Study Of Central And Side Jet With And Without Chevron Nozzle Exit On Gas Turbine Leading Edge Jet Impingement Cooling, Ahmad Yousef Alqasrawi

Theses

This thesis presents a comprehensive investigation into the application of jet impingement cooling on turbines blade leading edge. Gas turbines are extensively utilized in power generation and aerospace industries, where efficient cooling techniques are crucial to enhance the performance and lifespan of turbine blades. The leading edge of a turbine blade is particularly vulnerable to high-temperature exposure and thermal stresses, making it an essential area for effective cooling strategies. Jet impingement cooling is one of the most effective cooling techniques mostly used in the leading edge of rotating and stationary blades. This study aims to explore the performance of jet …

Cyberattacks And Security Of Cloud Computing: A Complete Guideline, Muhammad Dawood, Shanshan Tu, Chuangbai Xiao, Hisham Alasmary, Muhammad Waqas, Sadaqat Ur Rehman

Research outputs 2022 to 2026

Cloud computing is an innovative technique that offers shared resources for stock cache and server management. Cloud computing saves time and monitoring costs for any organization and turns technological solutions for large-scale systems into server-to-service frameworks. However, just like any other technology, cloud computing opens up many forms of security threats and problems. In this work, we focus on discussing different cloud models and cloud services, respectively. Next, we discuss the security trends in the cloud models. Taking these security trends into account, we move to security problems, including data breaches, data confidentiality, data access controllability, authentication, inadequate diligence, phishing, …

Grain Boundary And Texture Evolution Of Tib/Ti–2al–6sn Titanium Matrix Composite Under Electroshocking Treatment, Yaya Wu, Yan Wen, Anan Guo, Jian Zhou, Fei Yin, Lechun Xie, Liqiang Wang, Lin Hua, Weijie Lu, Lai-Chang Zhang

Research outputs 2022 to 2026

This work used electroshocking treatment (EST) plus external loading to regulate the microstructure of titanium matrix composites (TMCs). The external loading was 0.3 MPa. After EST plus external loading with 0.3 MPa, the was reduced to 2.53 m in size. The percentage of high angle grain boundaries (HAGBs) in increased first and then decreased. The percent of HAGBs in TiB decreased, mainly due to the introduction of abundant dislocations in the TiB/matrix interface after EST. After EST, the maximum texture strength of TiB decreased from 13.09 to 12.97, and that of decreased from 3.11 to 1.58. After EST under external …

Development Of Guidance, Navigation, And Control Systems For Multi-Spacecraft Assembly In Proximity Operations, Mohammed Ayman Atallah

Theses

This thesis presents the development of Guidance, Navigation, and Control (GNC) algorithms for multi-spacecraft assembly in proximity operations. A 3-DOF mathematical model of spacecraft relative translational motion is derived using the Euler-Lagrange method. Additionally, a 6-DOF mathematical model of spacecraft relative translational and rotational motion is derived using the twistor method, with consideration for the kinematic coupling effect. A new Linear Time-Invariant (LTI) model is developed based on the twistor model, which is utilized in the design of the GNC systems. Both LTI Model Predictive Control (MPC) and Linear Time-Varying (LTV) MPC algorithms are employed to develop Guidance and Control …

Selection Of Natural Surfactants For Possible Use In Improving Oil Recovery Of Carbonate Oil Reservoirs, Hiba Hachem Limam

Theses

Middle East petroleum industry is currently searching for the most suitable enhanced oil technique to improve the oil recovery from local oil reservoirs. The biggest challenge for the application of enhanced oil recovery (EOR) in the Middle East is the harsh environment (high salinity and temperature). Surfactant (synthetic or natural) is one of the EOR major players considered for application in the Middle East. However, synthetic surfactants have several drawbacks, such as economically unattractive and environmental impacts. This study investigated the possible use of natural surfactant extracted from the leaves of three types of plants, namely Aloe Vera, Tetraena qatarensis, …

Real-Time Object Tracking With Yolov5 And Recurrent Network On A Hardware Platform, Mohammed Abdulhakeem Alameri

Theses

The advancement of computer vision, particularly in the domain of object tracking, involves the integration of conventional feature-based approaches with contemporary deep learning methodologies. The initial phase of object detection plays a fundamental role in generating prospective objects for further tracking, and its level of success has a direct influence on the overall effectiveness of the tracking process. Many of the methods used to generate candidate objects start with object detection, and then object tracking algorithms are developed to link the object instances together to create the trajectories.
The primary difficulties in object tracking pertain to the establishment of reliable …

Development Of Unsaturated Polyester Resin Mortar Utilizing Industrial Wastes, Fatema Ahmed Alahmed

Theses

In recent years, polymer mortar (PM) has played a crucial role in the modern construction industry. It is gaining recognition as an effective and quick repair material in construction applications because it has several benefits over traditional Portland cement concrete. Various types of polymer binders, such as unsaturated polyester resin (UPR), have been used in these materials owing to their low cost, excellent strength, high workability, and rapid curing. This study investigates the feasibility of reutilizing locally available waste in the production of UPR-based polymer mortar, which facilitates the development of mortars with less environmental impact. In this study, the …

Boosting Snr Of Cascaded Fbgs In A Sapphire Fiber Through A Rapid Heat Treatment, Farhan Mumtaz, Hanok Tekle, Bohong Zhang, Jeffrey D. Smith, Ronald J. O'Malley, Rex E. Gerald, Jie Huang

Electrical and Computer Engineering Faculty Research & Creative Works

This Letter reports the performance of femtosecond (fs) laser-written distributed fiber Bragg gratings (FBGs) under high-temperature conditions up to 1600°C and explores the impact of rapid heat treatment on signal-to-noise ratio (SNR) enhancement. FBGs are essential for reliable optical sensing in extreme temperature environments. Comprehensive tests demonstrate the remarkable performance and resilience of FBGs at temperatures up to 1600°C, confirming their suitability for deployment in such conditions. The study also reveals significant fringe visibility improvements of up to ∼10 dB on a 1-m-long sapphire optical fiber through rapid heat treatment, representing a first-time achievement to the best of our knowledge. …

Iron Oxide Ore Mineralogy And Its Plant Flotation Circuits Nodal Analysis Simulation And Comparison, Ying Hou, Ahmed Sobhy, Samah Abdel Aziz

Mining Engineering Faculty Research & Creative Works

Mining operations usually provide ore of varying characteristics. At the Donganshan Sintering Plant, the ore is a low-grade, complex, hard-to-separate carbonate containing iron ore, and a two-step flotation circuit was previously developed to overcome the negative impact of the carbonates on the reverse flotation process. However, with the further expansion in the mining operations, it was difficult to maintain a highly efficient flotation process. Thus, the mineral liberation analyzer (MLA) was utilized to conduct an in-depth process mineralogy investigation. MLA showed that the main useful minerals in this ore are magnetite/hematite of 45% total iron, and the main gangue mineral …

Effect Of Type And Quantity Of Inherent Alkali Cations On Alkali-Silica Reaction, Pengfei Ma, Jiaoli Li, Jincheng Bai, Ying Zhuo, Lingyu Chi, Yanping Zhu, Zhenhua Shi, Hongyan Ma, Genda Chen

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In this study, the macroscopical expansion induced by alkali-silica reaction (ASR) and its corresponding ASR products are investigated using ordinary Portland cement (OPC) mortar specimens with a gradient of boosted alkalis. Experimental results show that the expansion increases with the concentration of inherent alkalis. Sodium-boosted samples expand approximately three times as much as potassium-boosted samples. ASR gels that are present in aggregate veins are calcium-free and amorphous; the atomic ratios of ASR gels are nearly independent of the type and quantity of alkali cations. Aggregate ASR gel exudation occurs in high (≥2.5 %) sodium cases and produces potential Na-shlykovite. Crystalline …

Implementation Of Experimental Static Recrystallization Of High Strength Steel Into Computational Simulation Of Multi-Pass Slab Hot Rolling, S. K. Dasari, S. Ganguly, A. Abutunis, K. Chandrashekhara, M. F. Buchely, S. N. Lekakh, R. J. O'Malley, T. Natarajan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Microstructural changes and softening due to static recrystallization have a critical influence on thermo-mechanical behavior of high strength steels during industrial multi-pass hot rolling. Numerical simulation using finite element analysis (FEA) can be used to accurately predict the softening behavior during the hot rolling process. Therefore, the implementation of an experimentally defined static recrystallization model into FEA is necessary to get realistic simulation prediction. in this study, the extent of softening during static recrystallization in Si and Mn alloyed high strength steel was measured using double hit tests. a Gleeble™ thermo-mechanical simulator was used to perform the double hit tests …

Comparison Of The Thermal Stability In Equal-Channel-Angular-Pressed And High-Pressure-Torsion-Processed Fe–21cr–5al Alloy, Maalavan Arivu, Andrew Hoffman, Jiaqi Duan, Jonathan Poplawsky, Xinchang Zhang, Frank Liou, Rinat Islamgaliev, Ruslan Valiev, Haiming Wen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Nanostructured steels are expected to have enhanced irradiation tolerance and improved strength. However, they suffer from poor microstructural stability at elevated temperatures. in this study, Fe–21Cr–5Al–0.026C (wt.%) Kanthal D (KD) alloy belonging to a class of (FeCrAl) alloys considered for accident-tolerant fuel cladding in light-water reactors is nanostructured using two severe plastic deformation techniques of equal-channel angular pressing (ECAP) and high-pressure torsion (HPT), and their thermal stability between 500–700 °C is studied and compared. ECAP KD is found to be thermally stable up to 500 °C, whereas HPT KD is unstable at 500 °C. Microstructural characterization reveals that ECAP KD …

Design Of Impact-Free Gaits For Planar Bipeds And Their Stabilization Using Impulsive Control, Aakash Khandelwal, Nilay Kant, Ranjan Mukherjee

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The problem of designing and stabilizing impact-free gaits is considered for point-foot planar bipeds. A set of geometric constraints, which eliminate impact forces at the time of leg interchange, are used to design the gaits. A family of gaits, where the stride length and walking speed can be chosen independently for each gait, is guaranteed to exist. A continuous controller is used to enforce the constraints associated with a desired gait and intermittent impulsive inputs are applied to stabilize the gait. A five-link biped example is used to illustrate the procedure for designing impact-free gaits. The effectiveness of the continuous …

Transportation Components Of The City Of Bennet Comprehensive Plan And Downtown Economic Development Plan, Kyle Mclaughlin

Community and Regional Planning Program: Theses

In partnership with the City of Bennet, the University of Nebraska, and Marvin Planning Consultants, this project assisted the creation of the City’s Comprehensive Plan and Downtown Economic Development Plan by creating a transportation focused report as a supplement to those plans. The project operates in six sections; Introduction and Overview, Evaluate the Present, Engage the Community, Recommendations, Strategies, and Policies, Implementation and Funding, and Monitoring and Evaluation. The project scope included existing conditions understanding, qualitative and quantitative transportation analysis, public engagement and stakeholder meetings, coordination with two plan creators, identifying transportation improvements, description of implementation steps, overview of available …

Design Guidance For Wetland-Road Crossings To Reduce Blanding’S Turtle Mortality Risk, Thomas P. Ballestero, Lauren E. White, Sandra Houghton, David Burdick, Josh Megyesy

Faculty Publications

Road mortality is a leading threat to freshwater turtles, particularly the Blanding’s turtle (Emydoidea blandingii), an endangered species in New Hampshire. Wildlife wetland-crossing structures, such as culverts and/or fences, have proven effective in reducing wildlife road mortality while retaining habitat connectivity. Funding for adequate wetland-crossing creation or restoration is limited, so prioritizing areas of high mortality risk is essential to ensuring that the resources spent are impactful. A research team of professionals from the New Hampshire Department of Environmental Services, New Hampshire Fish and Game, University of New Hampshire, and other organizations formed to create a model capable …

Sarcopenia Is Associated With Osteopenia And Impaired Quality Of Life In Children With Genetic Intrahepatic Cholestatic Liver Disease, Julia Boster, Nathan P. Goodrich, Cathie Spino, Kathleen M. Loomes, Estella M. Alonso, Binita M. Kamath, Ronald J. Sokol, Saul J. Karpen, Alexander Miethke, Benjamin L. Shneider, Jean P. Molleston, Rohit Kohli, Simon P. Horslen, Philip Rosenthal, Pamela L. Valentino, Jeffrey Teckman, Thomas N. Hangartner, Sundaram Shikha

Biomedical, Industrial & Human Factors Engineering Faculty Publications

Background:
Sarcopenia occurs in pediatric chronic liver disease, although the prevalence and contributing factors in genetic intrahepatic cholestasis are not well-described. The objective of this study was to measure muscle mass in school-aged children with genetic intrahepatic cholestasis and assess relationships between sarcopenia, clinical variables, and outcomes.

Methods:
Estimated skeletal muscle mass (eSMM) was calculated on dual-energy x-ray absorptiometry obtained in a Childhood Liver Disease Research Network study of children with bile acid synthesis disorders(BASD) alpha-1 antitrypsin deficiency (a1ATd), chronic intrahepatic cholestasis (CIC), and Alagille syndrome (ALGS). Relationships between eSMM, liver disease, and transplant-free survival were assessed.

Results:
eSMM was …

Advancing Airport Project Delivery: A Comparison Of Design-Build And Traditional Methods In Terms Of Schedule And Cost Performance, Ramy Khalef, Islam H. El-Adaway

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Current airport infrastructure is in a state of decline, with reports scoring it at an underperforming classification of D+. To address this issue, significant improvement and advancement of the infrastructure is needed. With backing on an authoritative level, the nation can expect an increase in the number of improvement projects. Airport stakeholders have long been accustomed to delivering their projects using traditional methods, such as design-bid-build (DBB). Design-build (DB) is an alternative delivery method that has added benefits for project metrics, such as schedule and cost performance. There is a lack of research evaluating DB within the context of airport …

Kytc Department Of Aviation Aircraft Maintenance Technician (Amt) Program Optimization, Bethany Paris, P. Gayle Marks, Bryan Gibson

Kentucky Transportation Center Research Report

The aviation industry is a linchpin of Kentucky’s economy. Major firms such as UPS, Amazon, and DHL have major hubs at Louisville Muhammad Ali International Airport (SDF) and Cincinnati/Northern Kentucky International Airport (CVG). As of December 2022, 4,570 aircraft mechanics and service technicians (AMTs) were employed in the state. Demand in this sector is poised to grow. As such, it is critical to understand what resources Kentucky has available to train the next generation of professionals and the number of people the aviation industry is likely to employ statewide over the next decade. Kentucky and the surrounding states are home …

Motif-Cluster: A Spatial Clustering Package For Repetitive Motif Binding Patterns, Mengyuan Zhou

School of Computing: Dissertations, Theses, and Student Research

Previous efforts in using genome-wide analysis of transcription factor binding sites (TFBSs) have overlooked the importance of ranking potential significant regulatory regions, especially those with repetitive binding within a local region. Identifying these homogenous binding sites is critical because they have the potential to amplify the binding affinity and regulation activity of transcription factors, impacting gene expression and cellular functions. To address this issue, we developed an open-source tool Motif-Cluster that prioritizes and visualizes transcription factor regulatory regions by incorporating the idea of local motif clusters. Motif-Cluster can rank the significant transcription factor regulatory regions without the need for experimental …

Flying To Net Zero With Sustainable Atos; Changing Cultures​, Eva Maleviti

Publications

What is Sustainability?

• World Commission on Environment and Development’s (WCED) 1987 Brundtland Report ‘’Our Common Future’’.
• Help world nations towards sustainable development.

17 Sustainable Development Goals

• The start of all industries are the 17 SDGs
• Aviation can address the 15 SDGs
• Net zero target suggest reduction of aviation emissions up to 21.2 Gt CO2

Design And Scale Model Of Wave Generator For The Testing Of Wave Energy Conversion Devices, Amanda Olla

Master's Theses

As the climate crisis draws more concern, research and development in wave energy as a renewable energy source has increased. Devices such as wave energy converters (WECs) are being researched, tested, and implemented to make wave energy a competitive power source. Testing of these devices is limited due to environmental concerns such as weather, location, and other issues. WECs require testing in a marine environment, however, performing testing in the actual environment may be difficult due to weather, access, mounting, and other issues. To eliminate environmental unknowns from testing, a wave simulator device can mimic wave behavior without the need …

Novel Castor Oil/Water/Ethanol Pickering Emulsions Stabilized By Magnetic Nanoparticles And Magnetically Controllable Demulsification, Mohammad J. Hasan, Peng Chen, Neithan Dominick, Erick S. Vasquez, Esteban E. Ureña-Benavides

Chemical and Materials Engineering Faculty Publications

A novel castor oil/water/ethanol Pickering emulsion, stabilized by magnetic nanoparticles (NPs), was developed to allow on-demand demulsification by an external magnetic field for the extraction of ethanol from aqueous solution using the castor oil. The emulsion was stabilized by Fe3O4-coated cellulose nanocrystals (CNC@Fe3O4) and lignin-coated Fe3O4 NPs (lignin@Fe3O4). The stability of the emulsions was investigated at various castor oil to ethanol-water ratios (50/50 and 70/30), various NP concentrations, and ethanol concentrations in the aqueous phase. The magnetically controlled demulsification ability of the emulsions was investigated by using a permanent magnet. The results showed that the 70/30 emulsions were more stable …