Engineering Commons^™

Urban Versus Lake Impacts On Heat Stress And Its Disparities In A Shoreline City, T. C. Chakraborty, Jiali Wang, Yun Qian, William Pringle, Zhao Yang, Pengfei Xue

Michigan Tech Publications

Shoreline cities are influenced by both urban-scale processes and land-water interactions, with consequences on heat exposure and its disparities. Heat exposure studies over these cities have focused on air and skin temperature, even though moisture advection from water bodies can also modulate heat stress. Here, using an ensemble of model simulations covering Chicago, we find that Lake Michigan strongly reduces heat exposure (2.75°C reduction in maximum average air temperature in Chicago) and heat stress (maximum average wet bulb globe temperature reduced by 0.86°C) during the day, while urbanization enhances them at night (2.75 and 1.57°C increases in minimum average air …

Deficient Aeronautical Decision-Making Contributions To Fatal General Aviation Accidents, Douglas D. Boyd, Mark Scharf Phd

Publications

INTRODUCTION: General aviation (GA), mainly comprised of light (≤12,500 lb) aircraft, maintains an inferior safety record compared with air carriers. To improve safety, aeronautical decision-making (ADM) practices have been advocated to GA pilots since 1991. Herein, we determined the extent to which GA pilots disregard such practices. METHODS: Fatal accidents (1991–2019) involving private pilots (PPLs) in single-engine airplanes were identified (N = 1481) from the National Transportation Safety Board AccessR database. Of these, deficient go/no-go and in-flight ADM-related mishaps were scored using the PAVE (pilot, aircraft, environment, external pressure)/IMSAFE (illness, medicine, stress, alcohol, fatigue, eating) and PPP (perceive, process, …

Understanding And Modeling Drivers’ En-Route Diversion Behavior During Congestion, Mohammad Shapouri

LSU Doctoral Dissertations

In the field of transportation, traffic assignment models primarily have been used to forecast driver route preferences, translating their choices into traffic flow patterns across networks. These models are grounded in distinct behavioral theories and strive to explain how drivers navigate routes based on network features and personal tendencies. Using an aggregation approach, conventional traffic assignment models distribute demand among paths, considering utility and attractiveness. Despite their prevalent use in transportation planning and operations, the fundamental behavioral assumptions of these models have rarely been thoroughly explored. This gap is further compounded by their limited consideration of real-time adjustments and choices …

Electrophertic Deposition And Characterization Of Molybdenum Disulfide On Silicon Substrates, Alex J. Young

LSU Doctoral Dissertations

The electrical characteristics of 2D materials such as high electron mobility and current density are of great interest to various fields from optoelectronics to renewable energy. Researchers have focused their efforts on transition metal dichalcogenides (TMDCs) due to their direct energy band gap. One such TMDC that has garnered much attention is molybdenum disulfide (MoS2). MoS2 has electrical properties comparable to graphene and is a TMDC with characteristics amenable to applications such as solar cells and sensors. Commonly deposited through time-consuming and complex deposition methods such as chemical vapor deposition (CVD), the viability of MoS2 as an electronic material will …

An Investigation Into The Challenges Of Contemporary Additive Manufacturing: Insights Into The Metallurgical Response Of Materials And Relevant Solution, Huan Ding

LSU Doctoral Dissertations

Additive Manufacturing (AM) has gained attention in recent years due to its unique capabilities in the fabrication of complex parts. As with any new research, there is still a lack of sufficient understanding in the field of additive manufacturing, and further investigation is needed to solve existing problems. Ultimately, the aim is to enable the widespread use of AM components across various industries.

Chapter One provides a brief introduction to the background and current bottlenecks of additive manufacturing technology. Chapter two focuses on the development of high-strength 7075 aluminum alloy (Al7075) for Fused Deposition Modeling and Sintering (FDMS) technology. Al7075 …

Multicolor Dye-Based Flow Structure Visualization For Seal-Whisker Geometry Characterized By Computer Vision, Ondřej Ferčák, Kathleen Lyons, Christin T. Murphy, Kristina M. Kamensky, Raul Bayoan Cal

Mechanical and Materials Engineering Faculty Publications and Presentations

Pinniped vibrissae possess a unique and complex three-dimensional topography, which has beneficial fluid flow characteristics such as substantial reductions in drag, lift, and vortex induced vibration. To understand and leverage these effects, the downstream vortex dynamics must be studied. Dye visualization is a traditional qualitative method of capturing these downstream effects, specifically in comparative biological investigations where complex equipment can be prohibitive. High-fidelity numerical simulations or experimental particle image velocimetry (PIV) are commonplace for quantitative high-resolution flow measurements, but are computationally expensive, require costly equipment, and can have limited measurement windows. This study establishes a method for extracting quantitative data …

Building Services Engineering November/December 2023

Building Services Engineering

No abstract provided.

Biomimetic Approach To Elucidate The Role Of Microenvironment In Regulating Cell Communications In Liver Diseases, Youra Moeun

Dissertations and Doctoral Documents, University of Nebraska-Lincoln, 2023–

Liver is a complex organ but often underappreciated for its functions to remove toxins and fight infection in the body. Despite the ongoing prevalence of patients contracting chronic liver diseases, coupled with a global healthcare investment of approximately $70 billion, there is still no effective treatment for chronic liver diseases including alcoholic liver disease. The purpose of this dissertation was to understand the interactions of parenchymal and non-parenchymal liver cells in physiological and pathological like environments. This allowed us to recreate a healthy and the diseased microenvironments to observe the stages of the liver diseases development and apply appropriate treatments …

Modeling Overdraft-Driven Nitrate Transport In Shallow Wells For Mitigation And Scenario Planning, Jonathan Cronk

Department of Agricultural and Biological Systems Engineering: Dissertations, Theses, and Student Research

In Nebraska, average nitrate concentrations in groundwater have doubled since 1974, making water quality management more important than ever. As droughts, heat waves, and floods become more common climate events, understanding their impacts will be necessary to make informed management decisions. Emerging literature describes that drought correlates to an increase in the concentration of nitrate-N at domestic and irrigation wells, however the relative contributions of the mechanisms thought to be responsible is currently unknown.

This research assessed the impact of recharge and pumping rate changes as two mechanisms affecting nitrate-N concentration during drought, assessed the relationship between well depth and …

Meta-Analysis Of Insulated Concrete Wall Panel Design Methods For Shear And Flexure Behavior, Maryam Al-Bayati

Durham School of Architectural Engineering and Construction: Dissertations, Theses, and Student Research

Insulated Concrete wall panels have been designed and constructed since the early 1950s with various shear ties, dimensions, and methods; nonetheless, thermal bridging and rational design are still a concern. Many companies have recently developed plastic connectors that have gradually replaced solid concrete sections and steel connectors due to their superior thermal efficiency and strength. However, there is no generally accepted method for predicting the behavior of sandwich wall panels in structural engineering practice or codes, but many methods have been used since the early 1920. This study aims to evaluate the accuracy of current methods for predicting the flexural …

Continuous Time Recurrent Network For Human Activity Detection, Abdallah Al Zubi

Durham School of Architectural Engineering and Construction: Dissertations, Theses, and Student Research

Human activity detection is crucial to personalize the control of the building environment. For example, understanding certain human activities (e.g., walking, sitting, etc.) for an occupant in a building helps provide the proper thermal comfort control. However, these applications require large-scale neural networks that are challenging to implement and train.

In this thesis, we implemented a continuous-time recurrent neural network implementation (CTRNN) network that can solve real-time human activity detection with a smaller-size network. The CTRNN uses differential equations with a time constant to describe the neuron equations. It was implemented and trained for the first time using TensorFlow. Specifically, …

Skip The Grid: Solar System Installations In The Navajo Nation, Gina H. Chun

Construction Management

Skip the Grid is an interdisciplinary project that involves installing solar energy systems in the Navajo Nation. The project’s mission was to support the Navajo families, specifically the students that have limited access to light which directly affects their education. On March 26, 2023, a team of 20 California Polytechnic State University San Luis Obispo (Cal Poly) students, across eight different majors, travelled to Arizona to collaborate with the Red Mesa and Chinle Unified School Districts to install “off-grid” solar energy systems and lights. Through this project the Cal Poly students learned about the people of Navajo Nation, solar energy, …

Vacancy Ordering In Zirconium Carbide With Different Carbon Contents, Yue Zhou, Jeremy Lee Watts, Cheng Li, William Fahrenholtz, Gregory E. Hilmas

Materials Science and Engineering Faculty Research & Creative Works

Zirconium carbide (ZrCx) ceramics with different carbon contents were prepared by reactive hot-pressing. The rock-salt structure of ZrCx was the only phase detected by x-ray diffraction of the hot pressed ceramics. The relative densities of ZrCx decreased as carbon content increased, in general. The actual carbon contents were measured by completely oxidizing the ZrCx ceramics to ZrO₂. For most compositions, the actual carbon contents were higher than nominal batched compositions, presumably due to carbon uptake from the graphite furnace and hot press dies. Selected area electron diffraction and neutron powder diffraction revealed the presence of carbon vacancy ordering …

Searching For Unknown Material Properties For Am Simulations, Aaron Flood, Rachel Boillat, Sriram Praneeth Isanaka, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Additive manufacturing (AM) simulations are effective for materials that are well characterized and published; however, for newer or proprietary materials, they cannot provide accurate results due to the lack of knowledge of the material properties. This work demonstrates the process of the application of mathematical search algorithms to develop an optimized material dataset which results in accurate simulations for the laser directed energy deposition (DED) process. This was performed by first using a well-characterized material, Ti-64, to show the error in the predicted melt pool was accurate, and the error was found to be less than two resolution steps. Then, …

Growth Of Germanium Thin Films On Sapphire Using Molecular Beam Epitaxy, Emmanuel Wangila, Peter Lytvyn, Hryhorii Stanchu, Calbi Gunder, Fernando Maia De Oliveira, Samir Saha, Subhashis Das, Niroshi Eldose, Chen Li, Mohammad Zamani-Alavijeh, Mourad Benamara, Yuriy I. Mazur, Shui-Qing Yu, Gregory J. Salamo

Electrical Engineering Faculty Publications and Presentations

Germanium films were grown on c-plane sapphire with a 10 nm AlAs buffer layer using molecular beam epitaxy. The effects of Ge film thickness on the surface morphology and crystal structure were investigated using ex situ characterization techniques. The nucleation of Ge proceeds by forming (111) oriented three-dimensional islands with two rotational twin domains about the growth axis. The boundaries between the twin grains are the origin of the 0.2% strain and tilt grains. The transition to a single-grain orientation reduces the strain and results in a better-quality Ge buffer. Understanding the role of thickness on material quality during the …

Building Services Engineering September/October 2023

Building Services Engineering

No abstract provided.

Heat Transfer Performance Of Single-Phase Circular Heat Sink With Micro Pin-Fin, Mouza Abdulla Al Shamsi

Theses

This thesis presents a numerical study of laminar forced convection in a novel design of a microscale single phase water cooled circular heat sink with pin fins developed and analyzed to serve as a miniaturized cooling system. The developed heat sink in this study aims to achieve efficient heat dissipation from high electronics integration that generates high heat flux and non-uniform temperature distribution, which leads to the reduction of life and reliability of electronic devices.

Numerical analysis of ten different configurations of the circular heat sink has been carried out for the heat flux of 100 W/cm2 at range of …

Flexible And Sewable Electrode Based On Ni-Co@Pani-Salphen Composite-Coated On Textiles For Wearable Supercapacitor, Touba Rezaee Adriyani, Ali A. Ensafi, B. Rezaei

Chemistry & Biochemistry Faculty Publications and Presentations

Flexible electrodes with high deformability and energy density are critical for electronic textiles. The key factor for achieving high-performance supercapacitors with superior power and energy density is the evaluation of materials that exhibit exceptional capacitive performance. Herein, we have prepared Ni-Co nanoparticles at the surface of polyaniline-salphen (Ni-Co@PS). Then, followed by casting Ni-Co@PS on a conductive carbon cloth (CC) as a substrate through a facile in-situ polymerization strategy. The morphologies of Ni-Co@PS composite were characterized by different methods such as FE-SEM, XPS, XRD, BET, and electrochemical methods. This nanocomposite showed high tolerability and a large surface area with excellent behavior …

Evolutionary History Of Western Eos Chaos Of Valles Marineris, Mars: Insights From Morphological Characteristics, Asif Iqbal Kakkassery, V. J. Rajesh, Rishitosh K. Sinha, Devika Padmakumar, K. S. Sajinkumar

Michigan Tech Publications, Part 1

The dynamics of aqueous processes within the Eos Chasma region in the trough of Valles Marineris on Mars have been attributed to a variety of Hesperian-aged landforms. We aim to improve the understanding of the geological characteristics of the western part of the Eos Chaos by investigating the morphological, topographical, and thermo-physical characteristics of the western semi-circular segment of Valles Marineris. The western Eos Chaos is characterized by remnants of an elevated crater rim, a central peak, and a circular boundary. Based on these observations, we infer that the study area is an ancient, highly degraded impact crater. Our observations …

Development Of Eco-Friendly Chitosan-G-Polyacrylamide Preformed Particle Gel For Conformance Control In High-Temperature And High-Salinity Reservoirs, Reem Elaf, Ahmed Ben Ali, Mohammed Saad, Ibnelwaleed A. Hussein, Baojun Bai

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Oil and gas extraction has become challenging nowadays due to the accompanying amount of excess produced water that results in poor recoverability of hydrocarbon, besides other environmental and economic isues. A recent and efficient technology for conformance control is the injection of preformed particle gels (PPGs), which results in a more practical production process. Nevertheless, existing treatments fail in high-temperature reservoirs, are extremely sensitive to salinity, and are hazardous. The characteristics of the designed PPG, such as mechanical strength and thermal durability, is mainly depend on their crosslinking method. Polysaccharides-based gels prepared by physical crosslinking are weaker than the ones …

Innovative Approaches To Poultry Processing Wastewater Treatment: The Stainless Steel Ultrafiltration Membrane As A Viable Option, Saubana Olorunrola Dada, Chidambaram Thamariselvan, Mahmood Jebur, Sumith Ranil Wickramasinghe

Chemical Engineering Faculty Publications and Presentations

In pursuit of sustainability, we explored replacing conventional dissolved air floatation (DAF) in poultry processing wastewater (PPW) treatment with a precisely tuned 0.02 µm stainless-steel ultrafiltration (SSUF) membrane. SSUF is a robust, homogenously porous membrane with strong chemical resistance, ease of cleaning, and exceptional resistance to organic fouling. Unlike polymeric membranes, it can be regenerated multiple times, making it a cost-effective choice due to its compatibility with harsh chemical cleaning. The PPW used for the study was untreated wastewater from all processing units and post-initial screening. Our study revealed the SSUF membrane’s exceptional efficiency at eliminating contaminants. It achieved an …

Peroxi-Electrocoagulation For Treatment Of Trace Organic Compounds And Natural Organic Matter At Neutral Ph, Donald R. Ryan, Patrick J. Mcnamara, Claire K. Baldus, Yin Wang, Brooke K. Mayer

Civil and Environmental Engineering Faculty Research and Publications

Iron-based oxidation technologies can be advantageous for mitigating trace organic compounds (TOrCs) during water and wastewater treatment due to their production of hydroxyl radicals. However, iron-based oxidation often occurs at acidic pH to promote Fenton's reaction, which limits the processes' feasibility for treatment applications. This study focused on utilizing iron-electrocoagulation (EC) paired with ex situ H₂O₂ addition (peroxi-electrocoagulation [EC:H₂O₂]) to promote oxidative reactions at neutral pH conditions. The hydroxyl radical probe para-chlorobenzoic acid (pCBA) was used to gauge oxidant activity and serve as a representative TOrC. The impact of water …

Impact Of Silicon Ion Irradiation On Aluminum Nitride-Transduced Microelectromechanical Resonators, David D. Lynes, Joshua Young, Eric Lang, Hengky Chandrahalim

Faculty Publications

Microelectromechanical systems (MEMS) resonators use is widespread, from electronic filters and oscillators to physical sensors such as accelerometers and gyroscopes. These devices' ubiquity, small size, and low power consumption make them ideal for use in systems such as CubeSats, micro aerial vehicles, autonomous underwater vehicles, and micro-robots operating in radiation environments. Radiation's interaction with materials manifests as atomic displacement and ionization, resulting in mechanical and electronic property changes, photocurrents, and charge buildup. This study examines silicon (Si) ion irradiation's interaction with piezoelectrically transduced MEMS resonators. Furthermore, the effect of adding a dielectric silicon oxide (SiO₂) thin film is …

Towards A Virtual Test Framework To Predict Residual Compressive Strength After Lightning Strikes, Scott L.J. Millen, Xiaodong Xu, Juhyeong Lee, Suparno Mukhopadhyay, Michael R. Wisnom, Adrian Murphy

Mechanical and Aerospace Engineering Faculty Publications

A novel integrated modelling framework is proposed as a set of coupled virtual tests to predict the residual compressive strength of carbon/epoxy composites after a lightning strike. Sequentially-coupled thermal-electric and thermo-mechanical models were combined with Compression After Lightning Strike (CAL) analyses, considering both thermal and mechanical lightning strike damage. The predicted lightning damage was validated using experimental images and X-ray Computed Tomography. Delamination and ply degradation information were mapped to a compression model, with a maximum stress criterion, using python scripts. Experimental data, in which artificial lightning strike and compression testing were performed, was used to assess the predictive capabilities …

On Quantifying Uncertainty In Lightning Strike Damage Of Composite Laminates: A Hybrid Stochastic Framework Of Coupled Transient Thermal-Electrical Simulations, R. S. Chahar, J. Lee, T. Mukhopadhyay

Mechanical and Aerospace Engineering Faculty Publications

Lightning strike damage can severely affect the thermo-mechanical performance of composite laminates. It is essential to quantify the effect of lightning strikes considering the inevitable influence of material and geometric uncertainties for ensuring the operational safety of aircraft. This paper presents an efficient support vector machine (SVM)-based surrogate approach coupled with computationally intensive transient thermal-electrical finite element simulations to quantify the uncertainty in lightning strike damage. The uncertainty in epoxy matrix thermal damage and electrical responses of unprotected carbon/epoxy composite laminates is probabilistically quantified considering the stochasticity in temperature-dependent multi-physical material properties and ply orientations. Further, the SVM models are …

Microbial Glycosylation Of Antitubercular Agent Chlorflavonin, Jie Ren, Jixun Zhan

Biological Engineering Faculty Publications

Flavonoids have shown health-benefiting properties, such as antioxidative and anti-inflammatory activities, and are commonly used as nutraceuticals and pharmaceuticals. Although flavonoids are predominantly identified from plants, several filamentous fungal species have also been reported to produce bioactive flavonoids, including chlorflavonin from Aspergillus candidus, a novel halogenated flavonoid with potent antifungal and antitubercular (anti-TB) activities. Unfortunately, the low water-solubility of this molecule may hinder its bioavailability. Glycosylation is an effective method to enhance the polarity of natural products and alter their physicochemical properties. This work focuses on the development of novel water-soluble chlorflavonin derivatives to combat the threat of drug-resistant …

Integrating The Concept Of Complete Streets Into Pavement Preservation, Sirisha Gangireddy

LSU Master's Theses

This study is motivated by the evident gap in integrating Complete Streets principles into pavement preservation. Complete Streets opportunities, which aim to accommodate all road users, are typically encouraged in all kinds of projects including new construction, reconstruction, preservation, and rehabilitation. While the concept of Complete Streets is understood in terms of new construction (e.g., building sidewalks), its application through pavement preservation programs is not well-developed. To bridge the gap between the Complete Streets and pavement preservation, this study conducted a comprehensive review on how state Department of Transportation (DOTs) are currently incorporating Complete Streets into pavement preservation and identified …

Mems Cantilever Biosensors Driven By Fringe Effect: Voltage-Amplitude Response Of Parametric Resonance, Miguel A. Martinez, Dumitru I. Caruntu

Mechanical Engineering Faculty Publications

This paper deals with voltage-amplitude response of fringing field/effect actuated micro-electromechanical system (MEMS) cantilever beam resonator biosensors at parametric resonance. The system consists of a flexible electrode (cantilever beam) and a fixed electrode (ground plate) in parallel, connected through an AC voltage source. The electrostatic force induced is due to the parallel-plate capacitance, which is directly related to the overlapping area of the two electrodes (Palmer’s Formula). In addition, fringing field electrostatic actuation must be accounted for. This is due to the bending of electric field lines from the ground plate to the top and side walls of the cantilever …

Amplitude-Voltage Response Of Parametric Resonance Of Electrostatically Actuated Circular Membranes, Marcos Alipi, Dumitru I. Caruntu

Mechanical Engineering Faculty Publications

This paper deals with the amplitude-voltage response of parametric resonance of electrostatically actuated MEMS circular membranes resonator for sensing applications. The system consists of a flexible circular membrane over a parallel ground plate. A soft AC voltage is applied between the MEMS membrane and ground plate to actuate the membrane near its first natural frequency. Two methods of investigation are used in this research, namely the method of multiple scales (MMS), and the reduced order model (ROM). These methods were used to solve for the voltage response of the MEMS analytically and numerically. This work also reports the effects the …

Quantitative Gait And Balance Outcomes For Ataxia Trials: Consensus Recommendations By The Ataxia Global Initiative Working Group On Digital-Motor Biomarkers, Winfried Ilg, Sarah Milne, Tanja Schmitz-Hübsch, Lisa Alcock, Lukas Beichert, Enrico Bertini, Helen Dawes, Christopher M. Gomez, James Mcnames, Multiple Additional Authors

Electrical and Computer Engineering Faculty Publications and Presentations

With disease-modifying drugs on the horizon for degenerative ataxias, ecologically valid, finely granulated, digital health measures are highly warranted to augment clinical and patient-reported outcome measures. Gait and balance disturbances most often present as the first signs of degenerative cerebellar ataxia and are the most reported disabling features in disease progression. Thus, digital gait and balance measures constitute promising and relevant performance outcomes for clinical trials.

This narrative review with embedded consensus will describe evidence for the sensitivity of digital gait and balance measures for evaluating ataxia severity and progression, propose a consensus protocol for establishing gait and balance metrics …