Structures and Materials Commons^™

Hybrid Structural Composites With Energy Harvesting Capabilities, Simon Furnes

Doctoral Dissertations and Master's Theses

Hybrid materials have received significant interest due to the potential enhancements they provide over traditional materials such as sensing, actuating, energy scavenging, thermal management, and vibration damping. While traditional materials can be utilized for either one of these functions or loadbearing, the hybrid materials are superior as they allow combination of a wide array of functionalities whilst being suitable for load-bearing purposes.

The goal of this thesis is to elucidate the synergistic effects of hybridization of two piezoelectric materials; zinc oxide nanowires (ZnO NWs) and thin film of lead zirconium titanate (PZT) on the mechanical and energy harvesting of beams …

Thermal Bending, Buckling And Post-Buckling Analysis Of Unsymmetrically Laminated Composite Beams With The Effects Of Moisture And Geometric Imperfections, Claudia Barreno

Doctoral Dissertations and Master's Theses

This thesis is concerned with the analytical study of the thermal bending, buckling, and post-buckling of unsymmetrically laminated composite beams with imperfection under hygrothermal effects. Three different boundary conditions will be considered on this study. The non-linear governing partial differential equations are derived by taking into account the von-Karman geometrical nonlinearity for an imperfect unsymmetrical laminated composite beam. Classical beam theory (CBT) as well as first order shear deformation theory (FSDT) will be used. The effects of temperature, angle of orientation, moisture variations, imperfection, and geometrical parameters, will be evaluated and discussed. Two different laminated composite laminates will be considered: …

A Comparison Of Crushing Parameters Of Graphite Composite Thin-Walled Cylinders Cured In Low And High Pressures, Trenton John Matson

Master's Theses

Out-of-Autoclave (OoA) processes for manufacturing aerospace-grade parts needs to be better understood to further the development and success of industries that are manufacturing reusable launch vehicles, military and commercial aircraft, and spacecraft. Overcoming the performance limitations associated with OoA, also known as low-pressure prepreg curing, methods (void count, energy absorption, etc.) will help decrease the costs associated with aerospace composite manufacturing and the negative environmental effects correlated with high-pressure composite curing methods. Experimental, theoretical, and numerical approaches are used to explore both low and high-pressure curing cycles and how the two different processes affect final cured parts. Quasi-static uniaxial compression …

Micrometeoroid Impacts On Periodic Spacecraft Structures, Victoria West, Luis Buades, Hanson-Lee Harjono

The Journal of Purdue Undergraduate Research

No abstract provided.

Secondary Electron Yield Measurements Of Carbon Nanotube Forests: Dependence On Morphology And Substrate, Brian Wood, Jordan Lee, Gregory Wilson, T. -C. Shen, Jr Dennison

Journal Articles

Total, secondary, and backscatter electron yield data were taken with beam energies between 15 eV and 30 keV, in conjunction with energy emission data, to determine the extent of suppression of yield caused by carbon nanotube (CNT) forest coatings on substrates. CNT forests can potentially lower substrate yield due to both its inherently low-yield, low-atomic number (Z) carbon composition, and its bundled, high-aspect ratio structure. Rough surfaces, and in particular, surfaces with deep high-aspect-ratio voids, can suppress yields, as the electrons emitted from lower lying surfaces are recaptured by surface protrusions rather than escaping the near-surface region. Yields of multilayered …

Wireless Antenna Detection Of Electrostatic Discharge Events, Allen Andersen, Jr Dennison

Journal Articles

Wireless intraspacecraft communication technology is being developed for signal transfer on space missions to save weight and simplify the design. One consideration for this new technology is its interaction with space environmentinduced electrostatic discharges (ESDs). The short time scales of spacecraft ESD events result in broad frequency band signals that can interact with high-frequency wireless antennas. These interactions present a source of signal noise. However, they also present a possibility of in-flight wireless ESD monitoring. We present laboratory measurements of arcing on common spacecraft insulators using commercially available single-band 2.4-GHz and dual-band 2.4-/5.8-GHz Wi-Fi antennas. These wireless detections are shown …

Manipulating Fiber Orientation For The Reduction Of Warpage In Carbon Fiber Composite Sandwich Panels, Landon Burnley, Gabrielle Correia

Materials Engineering

Safran Cabin (Santa Maria, CA), previously known as Zodiac Aerospace, designs and manufactures interior cabin components for private and commercial aircraft. Carbon fiber face sheets have recently been incorporated in their overhead luggage bin assemblies which utilize a composite sandwich panel design, in order to provide additional stiffness to the previous glass fiber sandwich panels. Since the introduction of carbon fiber in these luggage bin panels, Safran has experienced an increase in warpage during manufacturing. When inspected by quality control, the panels are tested mimicking how they are installed in aircraft. If the panels do not meet specifications, the warped …

The Effects Of Atomic Oxygen On Patch Antenna Performance And Lifetime, Max J. Barta

Master's Theses

The space environment is a volatile and challenging place for satellites to survive in. For Low Earth Orbiting (LEO) satellites, atomic oxygen (AO) is a constant corrosive effect that degrades the outer surface of satellites over long durations. Atomic oxygen exists in the atmosphere between 180 and 675 km and has a relatively high energy at 4.5 eV, which allows AO to break molecular bonds in materials on the surfaces of spacecraft. As the number and complexity of CubeSat missions increase, there is an increased risk that AO degradation on commercial off the shelf parts (COTS), such as antenna, could …

Investigation Of Fundamental Principles Of Rigid Body Impact Mechanics, Khalid Alluhydan

Mechanical Engineering Research Theses and Dissertations

In impact mechanics, the collision between two or more bodies is a common, yet a very challenging problem. Producing analytical solutions that can predict the post-collision motion of the colliding bodies require consistent modeling of the dynamics of the colliding bodies. This dissertation presents a new method for solving the two and multibody impact problems that can be used to predict the post-collision motion of the colliding bodies. Also, we solve the rigid body collision problem of planar kinematic chains with multiple contacts with external surfaces.

In the first part of this dissertation, we study planar collisions of Balls and …

Modifying Casting Parameters To Improve The High Temperature Ductility Of Investment Cast Nickel-Based Superalloy Pwa 1455, Lars Alexander Hedin, Cole Magnum Introligator

Materials Engineering

PCC Structurals, an industry leader in superalloy investment castings, has observed inconsistencies in the stress rupture performance of polycrystalline nickel-based superalloy PWA 1455. PCC has changed their casting parameters to reduce the thermal gradient during cooling but have been unable to correlate these changes with an increase in stress rupture elongation. Metallographic examination of past samples indicated microstructures composed of non- equiaxed dendritic grains with mean diameter of .021 inches along the test axis. A similar study on polycrystalline superalloys has indicated that excessive superheat temperatures above the liquidus can result in large grains identical to those observed, limiting the …

Redesign Of Cubesat For Beam Charging, Kuba Preis

Industrial and Manufacturing Engineering

This paper is intended to be a study in the applications of the design freedom granted by additive manufacture in the design of a 1U CubeSat frame. The main loads experienced by a CubeSat are structural (during launch) and thermal (solar radiation). Beam charging is an emerging technology which involves charging a CubeSat using a laser beam. In this paper, a CubeSat frame was redesigned to account for the structural loads induced during launch and the thermal loads induced when beam charging. The thermal, weight, design, and structural requirements for a new CubeSat design were derived. The 1U CubeSat frame …

Effects Of Corrugations On Stiffness Properties Of Composite Beams For Structural Applications, Jane Xiao

Master's Theses

Composites have high strength-to-weight ratios, which is particularly desired for applications with weight restrictions. Common composite materials such as carbon fiber reinforced plastic (CF) and fiber glass reinforced plastic (FG) were used in this research. While composite materials possess high stiffness and strength properties, the stiffness of composite laminates may be maximized by changing the geometry. By adding corrugations, the flexural stiffness is increased in one direction compared to the stiffness of a flat part with the same amount of material. Thus, stiffness increases without a change in weight. The primary goal of this research was to investigate the stiffness …

Atomic Oxygen Effects On Particulate Contamination And Short Beam Strength Of Carbon Composites, Marlee K. Litzinger

Master's Theses

In order to design a successful space system, the unique challenges of the space environment it will operate in must be considered during the design process. Atomic oxygen (AO) is a detrimental environmental effect found in Low Earth Orbit (LEO) that affects spacecraft surfaces by oxidizing and eroding material over time, particularly polymers. Carbon fiber/epoxy composites are a commonly used spacecraft material affected by AO exposure. Carbon composites are used as a structural material, such as on solar panels; their large surface area therefore is a potential contamination source to sensitive components. The Space Environments and Testing Lab at California …

Development Of A Multi-Probe Kelvin Scanner Device For Industrially-Relevant Characterization Of Surface-Activated Carbon Fiber Reinforced Thermoplastic Composites, Kirby Simon

McKelvey School of Engineering Graduate Student Theses & Dissertations

Carbon fiber reinforced thermoplastic (CFRTP) composites are becoming increasingly attractive materials in manufacturing due to their lightweight nature, mechanical strength, and corrosion resistance. Surface activation of these materials is usually required during processing to increase the bond strength of assemblies (aerospace and automotive industries) or improve adhesion with implants (biomedical industry). Industrially-relevant, nondestructive quality control methods for assessing the activation state of these materials do not currently exist, however. Applying principles discovered through the use of scanning probe microscopy, a multiple-probe Kelvin scanning (MPKS) device has been developed that can assess the uniformity of the activation state of plasma-treated CFRTP …

Hypervelocity Impact Analysis Of Hybrid Nanocomposite Sensors For Inflatable Space Structures, Yachna Gola

Doctoral Dissertations and Master's Theses

Future space exploration requires easy-to-transport, and easy-to-build and deploy space habitats. NASA and Bigelow Aerospace have collaborated so that human habitation can be made safe and easy with inflatable space habitats (Litteken, 2017). One of the biggest threats faced by these structures in outer space is impact damage by micrometeoroid orbital debris (MMOD) traveling at velocities as high as 15 km/s (Lemmens, Krag, Rosebrock, & Carnelli, 2013). This work presents fabrication and testing of hybrid nanocomposites with carbon nanotubes (CNT) and coarse graphene nanoplatelets (GNP) as fillers and flexible epoxy matrix, that are proposed to be used for sensing the …

On The Anisotropic Behavior Of Electrodes For Electrical-Based Monitoring Of Cfrp Laminated Composites, Khaled Almuhammadi, Arief Yudhanto, Gilles Lubineau

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Electrical impedance tomography (EIT) is a promising structural health monitoring technique for carbon fiber-reinforced polymer (CFRP) composites. EIT technique has been specifically adopted as a non-destructive testing method along with the electrical characterization methods. Electrodes are the primary component in any EIT system because they act as an interface connecting the instrument/hardware to the structure under inspection. Simulation of electrical inspection of CFRP usually assumes the electrodes to be electrically isotropic interfaces. We show here that such isotropic assumption is a very poor approximation. We experimentally investigated the electrodes contact impedance behavior on CFRP-laminated composite specimens for different surface processing …

Internal Strain Assessment Using Fbgs In A Thermoplastic Composite Subjected To Quasi-Static Indentation And Low-Velocity Impact, M. Mulle, A. Yudhanto, G. Lubineau, R. Yaldiz, W. Schijve, N. Verghese

Mechanical and Aerospace Engineering Faculty Research & Creative Works

We present, for the first time, an experimental investigation of internal strain monitoring in thermoplastic composites subjected to quasi-static indentation and low-velocity impact using embedded fiber Bragg gratings (FBGs). The goal is to highlight the interest and limitations of the in-core instrumentation of glass fiber-reinforced polypropylene laminates subjected to these two classical loading conditions. We propose an instrumentation strategy utilizing FBGs that is expected to provide a reliable set of internal strain values and strain rates, which can be used for the analysis of the damage behavior and the validation of a numerical mesoscale model of laminates. Based on a …

Non-Linear Bending Analysis Of Functionally Graded Beams With Spring Constraints And Thermal Effects, Swetha Suresh

Doctoral Dissertations and Master's Theses

No abstract provided.

Piezoelectric Sensor Crack Detection On Airframe Systems, Kevin J. Lin

Theses and Dissertations

In 2008, the Department of Defense published a guidebook for a methodology named Condition-Based Maintenance Plus (CBM+) which capabilities include improving productivity, shortening maintenance cycles, lowering costs, and increasing availability and reliability. This push replaces existing inspection criteria, often conducted as non-destructive testing (NDT), with structural health monitoring (SHM) systems. The SHM system addressed utilizes guided Lamb waves generated by piezoelectric wafer active sensors (PWAS) to detect the existence, size, and location of damage from through-thickness cracks around a rivet hole. The SHM field lacks an experiment testing how small changes in receiver sensor distances affect damage detection. In addition, …

Initial Stage Of Fluid-Structure Interaction Of A Celestial Icosahedron Shaped Vacuum Lighter Than Air Vehicle, Dustin P. Graves

Theses and Dissertations

The analysis of a celestial icosahedron geometry is considered as a potential design for a Vacuum Lighter than Air Vehicle (VLTAV). The goal of the analysis is ultimately to understand the initial fluid-structure interaction of the VLTAV and the surrounding airflow. Up to this point, previous research analyzed the celestial icosahedron VLTAV in relation to withstanding a symmetric sea-level pressure applied to the membrane of the structure. This scenario simulates an internal vacuum being applied in the worst-case atmospheric environmental condition. The next step in analysis is to determine the aerodynamic effects of the geometry. The experimental setup for obtaining …

Revealing The Effects Of Matrix Behavior On Low-Velocity Impact Response Of Continuous Fiber-Reinforced Thermoplastic Laminates, A. Yudhanto, H. Wafai, G. Lubineau, S. Goutham, M. Mulle, R. Yaldiz, N. Verghese

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Matrix behavior is expected to widely influence the impact response of composites, but detailed conclusions in the case of thermoplastic laminates are still needed. In this paper, we investigated the effect of using either ductile homopolymer PP or less-ductile impact copolymer PP matrices on the low-velocity impact responses of continuous glass fiber-reinforced polypropylene (PP) laminate. These PP types represent two variants in the same family of thermoplastic matrix. A thorough experimental campaign was first performed to provide the tensile properties (for PP and glass/PP) and fracture toughness (Mode-I and Mode-II, glass/PP only) of the employed materials. Then, low-velocity impact tests …

In Situ Micro-Scale High-Speed Imaging For Evaluation Of Fracture Propagation And Fracture Toughness Of Thermoplastic Laminates Subjected To Impact, H. Wafai, A. Yudhanto, G. Lubineau, M. Mulle, T. Alghamdi, S. T. Thoroddsen, R. Yaldiz, N. Verghese

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Measuring parameters related to each damage mode of composites subjected to impact is very challenging because of the complex damage phenomenology. Here, we developed an experimental methodology for evaluating the micro-scale fracture characteristics of two principal damage modes, i.e., transverse crack and delamination, and providing the corresponding fracture toughness. We demonstrated the capability of the method by comparing and providing additional insights about two materials, namely homopolymer-based (ductile) and copolymer-based (less-ductile) glass/polypropylene thermoplastic composites. We found that (i) transverse crack behavior of both composites is similar as indicated by a small difference in their fracture toughness, (ii) delamination growth in …

W&B Problems For Far/Cs 25 Airplanes Tutorial, Nihad E. Daidzic

Aviation Department Publications

Weight and Balance (W&B) computations are essential step in ensuring that the aircraft (in this case FAR/CS 25 Transport-category airplanes) is properly loaded with its Center of Mass (CM) of Center of Weight/Gravity (CG) in the proper range.

Influence Of Process-Induced Shrinkage And Annealing On The Thermomechanical Behavior Of Glass Fiber-Reinforced Polypropylene, M. Mulle, H. Wafai, A. Yudhanto, G. Lubineau, R. Yaldiz, W. Schijve, N. Verghese

Mechanical and Aerospace Engineering Faculty Research & Creative Works

We investigate the influence of process-induced shrinkage and subsequent annealing on the thermomechanical behavior of unidirectional laminates made of continuous glass fiber-reinforced polypropylene (GFPP). We use two different industrial lamination processes: static hot-presses (SHP), and double-belt press (DBP) that are characterized by different cooling rates and pressure levels and most importantly, by the use of a closed mold in the case of SHP manufacturing. We measure the longitudinal and transverse shrinkage during the manufacturing and annealing processes using embedded fiber Bragg gratings (FBGs). The SHP molding reveals much lower induced shrinkage in GFPP as compared to the DBP process, although …

Composite Recycler: Delamination, Nathan Sauer

All Undergraduate Projects

A great deal of composite waste is generated in the construction of wings for the Boeing 777. These carbon fiber “wing trimmings” are currently being disposed of in a landfill. These carbon fiber boards are made of several layers laminated together, making them very rigid and hard to recycle. This report proposes a method to delaminate the layers of these composite wing trimmings using a hydraulic press and a V-shaped steel die so that they may be more easily shredded and thus recycled. A top, “male” die with two points is pressed into a bottom, “female” die with three points …

3d Textile Preforms And Composites For Aircraft Strcutures: A Review, Abbasali Saboktakin

International Journal of Aviation, Aeronautics, and Aerospace

Over the last decades, the development of 3D textile composites has been driven the structures developed to overcome disadvantages of 2D laminates such as the needs of reducing fabrication cost, increasing through-thickness mechanical properties, and improving impact damage tolerance. 3D woven, stitched, knitted and braided preforms have been used as composites reinforcement for these types of composites. In this paper, advantages and disadvantages of each of them have been comprehensively discussed. The fabric architects and their specification in particular stitched preforms and their deformation mode for aerospace applications have been reviewed. Exact insight into various types of damage in textile …

Real-Time Electrical Impedance Monitoring Of Carbon Fiber-Reinforced Polymer Laminates Undergoing Quasi-Static Indentation, Khaled Almuhammadi, Arief Yudhanto, Gilles Lubineau

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Laminated composites are vulnerable to damage from out-of-plane loading, particularly impact loading, and the incurred damage is often only detected by evaluating the post-impact condition of the composites. Real-time monitoring techniques are desirable for early detection of damage. Utilizing changes in the electrical properties of composites to track incurred damage is promising, but the interpretation of such measurements is still challenging. Here, an electro-mechanical system is introduced to understand how well we could detect mechanical degradation in carbon-fiber-reinforced polymer (CFRP) plates undergoing a quasi-static indentation (QSI) test, which is representative of an impact load. The system measures the in situ, …

An Experimental Approach That Assesses In-Situ Micro-Scale Damage Mechanisms And Fracture Toughness In Thermoplastic Laminates Under Out-Of-Plane Loading, H. Wafai, A. Yudhanto, G. Lubineau, R. Yaldiz, N. Verghese

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Studying the response of laminated composites under out-of-plane loading routinely involves mechanical tests, such as quasi-static indentation or impact. The phenomenology during these tests is so complex that it is difficult to identify different material properties related to each failure mechanism (damage mode). We aim at providing an experimental approach, which is practical and fast, for assessing the in-situ micro-scale damage mechanism and extracting the fracture toughness in thermoplastic laminates under out-of-plane loading. To this end, we developed a dedicated, micro-scale, three-point bending (micro-3PB) test fitted inside a scanning electron microscope (SEM). In a single experiment, we were able: (i) …

Enhanced Surface Integrity With Thermally Stable Residual Stress Fields And Nanostructures In Cryogenic Processing Of Titanium Alloy Ti-6al-4v, James R. Caudill

Theses and Dissertations--Mechanical and Aerospace Engineering

Burnishing is a chipless finishing process used to improve surface integrity by severe plastic deformation (SPD) of surface asperities. As surface integrity in large measure defines the functional performance and fatigue life of aerospace alloys, burnishing is thus a means of increasing the fatigue life of critical components, such as turbine and compressor blades in gas turbine engines. Therefore, the primary objective of this dissertation is to characterize the burnishing-induced surface integrity of Ti-6Al-4V alloy in terms of the implemented processing parameters. As the impact of cooling mechanisms on surface integrity from SPD processing is largely unexplored, a particular emphasis …

Fe Modeling Methodology For Load Analysis And Preliminary Sizing Of Aircraft Wing Structure, Jun Hwan Jang, Sang Ho Ahn

International Journal of Aviation, Aeronautics, and Aerospace

It is a critical part at the basic design phase of aircraft structural design to build a finite element model and it will have a direct impact on time and cost for airframe structure development. In addition, the objective of finite element model will be varied depending on each design review phase and the modelling methodology varied accordingly. In order to build an effective and economic finite element model, it is required to develop adequate level of modelling methodology based on each design phase and its objectives. Therefore, in this paper, the finite element modeling methodology was presented for internal …