Structures and Materials Commons^™

Mars Rover Wheels And Drive, Presley S. Sacavitch, Ryan W. Trevena, Dylan A. Mack, Daniel Hudak

Mechanical Engineering

Cal Poly’s Poly1Rover team, advised by Professor Rich Murray, aims to deploy four student-designed mini-Mars rovers, each equipped with a sample-tube retrieval claw, before 2030. However, the wheels of Poly1Rover’s current 6th generation rover are not ready for deployment to Mars, as they do not utilize space-grade materials, are not optimized for manufacturability, and lack sufficient spoke compliance to absorb landing and high-impact loads. This project will be developed by a team of Mechanical Engineering students at California Polytechnic State University, San Luis Obispo (Cal Poly): Daniel Hudak, Dylan Mack, Presley Sacavitch, and Ryan Trevena. Next Intent is providing funding …

Team F16: Autonomous Research Plane, Andrew Sugamele, Andrew Whitacre, Nicholas Toal, Cole Bushur

Mechanical Engineering

The autonomous research plane is a remote-controlled plane used for both in-flight data collection and to explore new manufacturing methods for Design Build Fly, an engineering club on campus. The club does not have the resources or time to implement data collection for their competition plane, so we built a plane in parallel, following similar rules to mimic the work and schedule that the club would use during their season. We first did research and analysis to determine the structure of the plane, geometry of wings, sizing of the tail, and what airfoil to choose. The manufacturing process included making …

Rover On A Chip (Roach) Debris Utility & Solar Shell Technology (Dusst), Joshua Aaron Tuttobene, Jacquelyn Rose Banh, Nathan Christopher Chapman, Tanner Casey Wells

Mechanical Engineering

The Rover on A Chip project’s Debris Utility and Solar Shell Technology team’s final design is outlined in this document. Starting with the design of our system, this document highlights important progress made since the Critical Design Review and fully describes our final design and verification of our final prototype. We then justify these design choices by testing multiple functionalities and conditions to ensure they will meet all of our specifications. Next, we describe in detail our procurement manufacturing method for the project. Lastly, we wrap up by discussing recommendations and the next steps for the project moving forward.

Since …

Uv Space Imager Enclosure Coating, David Silva Cortez, Victor Alexander Rempel Dekhtyar, Maria L. Muñoz

Mechanical Engineering

The goal of this project is to reduce the amount of stray light entering an ultraviolet (UV) imager through absorption. This report outlines the use of ZnO nanoparticles mixed in an epoxy matrix for use in a CubeSat enclosure. Through testing, our team verified that the ZnO and epoxy coating experienced a peak absorption between 360-370 nm. The epoxy mixture with the .75% by weight ZnO nanoparticles absorbed up to 99.9 % of UV light at its peak. The effect on material properties, such as Young’s modulus and ultimate tensile strength, was also tested. Tensile tests demonstrated that adding ZnO …

Space Suit Attachment Quick Release System, Elyse C. Gillis-Smith, Andres I. Elzaurdia, Cole H. Stanton, Michael T. Roth

Mechanical Engineering

NASA plans to make it back to the Moon by 2024 with their Artemis Program, and stay there for a longer period of time to conduct research which will support the future of space exploration. While on the lunar surface, astronauts need to maximize their efficiency by carrying tools on their Exploration Extravehicular Mobility Unit (xEMU), and to accommodate this need, the Extravehicular Activity (EVA) Tools Team is pursuing a utility belt concept. The objective of this project is to develop a system capable of interfacing between the utility belt and any given tool, while also accommodating numerous restrictions and …

Vibration Isolation System, Bradley Y. Kwan, Bailey Groh, Max Wu, Nicole Yen

Mechanical Engineering

The Vibration Isolation System Senior Project is a collaborative group project between its sponsor, Maxar Technologies, and a team of students from Cal Poly - SLO to effectively design, manufacture, and test a structural assembly for satellites, isolating vibrations during launch and orbit conditions. After initial sponsor contact, requirements and needs were set which dictated deliverables for the senior project group. The group performed analyses to validate all design decisions, including a modified concept and design direction, selection of a prototype viscoelastic damping material, preliminary testing to validate design specifications, and detailed design and analysis toward a finalized design. Instead …

Miniaturized Ultraviolet Imager Phase Iii, Bradley D. Albright, Nicolas A. Armenta, Colin W. Harrop

Mechanical Engineering

This document details the work to date, June 9, 2020, done by the Cal Poly Mechanical Engineering senior project team, Miniaturized Ultraviolet Imager: Phase III (MUVI III), sponsored by the University of California, Berkeley – Space Sciences Laboratory (UCB SSL). MUVI III is the third senior project team of an ongoing design, MUVI: the prototype of a 2U sized CubeSat intended to capture aurora images in the ionosphere. The first team, MUVI I, finished development of the UV imager. The second team, MUVI II, designed the mirror mounting and deployable door mechanisms. The goal of MUVI phase III is to …

Ultraviolet Imager Application For A Cube Satellite, Jason Grillo, Troy Hajjar, Brady Hill

Mechanical Engineering

This document serves as the final design review (FDR) report for the 2018 Cal Poly CubeSat Ultraviolet Imager senior project, sponsored by UC Berkeley Space Sciences Laboratories (SSL). SSL wants to monitor the ionosphere above Earth to gain a better understanding of its properties and particle interactions. Far Ultraviolet (FUV) imaging is a good way to obtain high quality images of the ionosphere and the Earth's auroras, and advancement in optic technologies have made cube satellites (CubeSats) an ideal vessel for a FUV imager, as they are relatively low-cost, lightweight, and can be repeatedly deployed. These CubeSat FUV imagers could …

Deployable Antenna For Cubesat, Mackenzie Thomas Lennon, Caleb Andrew Barber, David Matthew Galves

Mechanical Engineering

This project is a proof-of-concept ground model of a large deployable antenna designed for the small space requirements of CubeSats. This small deployment module is designed to fit a 2 m by 1 m reflective antenna inside a storage volume of with the dimensions 20 cm by 20 cm x 40 cm. The reflector will be deployed to a parabolic shape with the goal of modeling the reflector necessary for high frequency communication. Because this module is designed as a proof-of-concept for the deployable parabolic reflector specifically, no electrical components will be incorporated and will just focus on the deployment …

Human Powered Helicopter: Rotor Structure, Joseph Ram, Juan Carlos Olvera

Mechanical Engineering

The following report encompasses the Human Powered Helicopter Rotor Team’s conceptual models and ideas based on research and modeling analysis. The following gives an overview of material researched, concept generation, analyzation, manufacturing, and testing for a rotor structure to be installed in a Human Powered Helicopter.

Design Of A Human Powered Helicopter Airframe, Sheen Kao, Daniel Layton, Philip Sobol

Mechanical Engineering

In 1989 Cal Poly’s Da Vinci III was the first human powered helicopter (HPH) to achieve flight; our goal is to research and develop a new airframe for the next generation Da Vinci. This report outlines a brief history of human powered flight and details a method of constructing for the airframe. An optimized airframe geometry was also researched and is explained in detail.