Structures and Materials Commons^™

Classification Of In-Flight Fatigue Cracks In Aircraft Structures Using Acoustic Emission And Neural Networks, Christopher Lee Rovik

Master's Theses - Daytona Beach

The research encompassed within this paper deals with the analysis and classification of fatigue cracks in aircraft structures. The particular structure that was examined was the vertical tail section of a Cessna T-303 Crusader aircraft. The analysis was performed using the nondestructive evaluation technique known as acoustic emission (AE), as well as the artificial intelligence of neural networks. Data were taken in a controlled laboratory environment as well as in a flying testbed aboard the aircraft.

The first part of the research involved the analysis of a typical aircraft structure in a controlled laboratory environment. This support structure was fabricated …

Skin-Stiffener Separation In Buckled Composite Plates And Shallow Shells, Mark Edward Robeson

Mechanical & Aerospace Engineering Theses & Dissertations

The development of an approximate analysis for predicting stresses in the skin-stiffener interface region of composite plates and shallow shells is presented. The analysis determines interlaminar normal stress and transverse shear stresses in the direction of the stiffener axial coordinate and the direction of the inplane coordinate perpendicular to the stiffener axis. The analysis accounts for skin-stiffener interfaces with nonzero thickness and for curvature in the skin and stiffener. The interlaminar normal stress and transverse shear stresses at the interface are applied to the lower face of the skin and the upper face of the stiffener flange as unknown functions, …

Electro-Mechanical Fatigue Behavior Of A Quasi-Isotropic Laminate With An Embedded Piezoelectric Actuator, Tse Lin Hsu

Theses and Dissertations

This study primarily investigated the electro-mechanical fatigue behavior of the embedded piezoelectric actuators in graphite/epoxy laminate with a lay-up of 0 | ± 45 | 90s. A secondary focus was the investigation of the mechanical fatigue effects of the 0 | 0 | ± 45 | 0 | 0 | 90s laminate with embedded PZT under tensile loading. All the fatigue tests were conducted with a triangular loading waveform which had a frequency of 10 Hz and with R=0. 1. In the electro-mechanical testing, the embedded actuator was excited by a -10 V to -100 V or a 10 V …

Chemical Kinetics And Heat Transfer In Polyurethane Foam And Resin Composites, Yumi Morisaki

Master's Theses - Daytona Beach

A development of the composite materials parts require knowledge of the theoretical model that describes the physics, the chemical kinetics, and the heat-transfer properties of the materials.

For this work, the chemical kinetics of the polyurethane foam and the fiberglass-reinforced resin is investigated individually. An adiabatic method, which is commonly used by many investigators, is used for the polyurethane foam, while an isothermal degree and the rate of cure relationship is applied for the resin. A heat transfer effect during the curing process of both polyurethane foam and the resin is also investigated. A common approximate method for the heat-conduction …

Vortex Wake And Exhaust Plume Interaction, Including Ground Effect, Ihab Gaber Adam

Mechanical & Aerospace Engineering Theses & Dissertations

Computational modeling and studies of the near-field wake-vortex turbulent flows, far-field turbulent wake-vortex/exhaust-plume interaction for subsonic and High Speed Civil Transport (HSCT) airplane, and wake-vortex/exhaust-plume interaction with the ground are carried out. The three-dimensional, compressible Reynolds-Averaged Navier-Stokes (RANS) equations are solved using the implicit, upwind, Roe-flux-differencing, finite-volume scheme. The turbulence models of Baldwin and Lomax, one-equation model of Spalart and Allmaras and two-equation shear stress transport model of Menter are implemented with the RANS solver for turbulent-flow modeling.

For the near-field study, computations are carried out on a fine grid for a rectangular wing with a NACA-0012 airfoil section and …

Experimental Geometry Optimization Techniques For Multi-Element Airfoils, Drew Landman

Mechanical & Aerospace Engineering Theses & Dissertations

A study is reported on geometry optimization techniques for high-lift airfoils. A modern three-element airfoil model with a remotely actuated flap was designed, tested, and used in wind tunnel experiments to investigate optimum flap positioning based on lift. All the results presented were obtained in the Old Dominion University low-speed wind tunnel. Detailed results for lift coefficient versus flap vertical and horizontal position are presented for two airfoil angles-of-attack: 8 and 14 degrees. Three automated optimization simulations, the method of steepest ascent and two variants of the sequential simplex method, were demonstrated using experimental data. An on-line optimizer was demonstrated …

Placement Of Piezoelectric Actuators For Active Control Of Vibration Using Modal Parameters, Xuegeng Zhu

Mechanical & Aerospace Engineering Theses & Dissertations

An equation is derived to model the piezoelectric actuators incorporation with flexible structures. This equation permits the comparison of the performance indices over the entire structure for a piezoelectric actuator with constant area, which is unachievable if the Finite Element Method is used for complicated structures.

An index has been developed for placement of piezoelectric actuator for control of vibration of a flexible structure. This index is derived from the definition of H2norm. Computation of the proposed index requires only the natural frequencies and corresponding mode shapes of the structures of interest. The method is well suited to large …