Structures and Materials Commons^™

Creep Of Hi-Nicalon™ S Ceramic Fiber Tows At 800°C In Air And In Silicic Acid-Saturated Steam, Scott J. Robertson

Theses and Dissertations

A facility was demonstrated that successfully resolved problems highlighted by previous attempts to study SiC fibers in steam. Monotonic tension and creep tests were conducted to characterize the fibers. The tensile strength of the fibers showed little dependence on applied stress rate, indicating a resistance to environmentally assisted crack growth. Climb-controlled diffusion in air and grain boundary sliding in silicic acid-saturated steam were the dominant damage mechanisms. Silicic acid-saturated steam had a degrading effect on the mechanical performance of the fibers, but much less than unsaturated steam environments. The Monkman-Grant relationship was demonstrated for Hi-NicalonTM S fibers and may be …

Polyacrylonitrile Copolymers: Effects Of Molecular Weight, Polydispersity, Composition, And Sequencing On Thermal Ring-Closing Stabilization, Jeremy D. Moskowitz

Dissertations

Controlled polyacrylonitrile (PAN)-based carbon fiber precursors with defined molecular weights, polydispersities, compositions, and architectures have been prepared for their study on thermal ring-closing stabilization behavior. PAN and its copolymers of number average molecular weights exceeding 170,000 g/mol were successfully synthesized via low temperature reversible addition-fragmentation chain transfer (RAFT) polymerization. RAFT polymerizations of PAN-based precursors were compared to conventional free radical solution polymerizations with a focus on the effects of molecular weight and polydispersity on structural evolution and cyclization efficiency. When RAFT polymerization was extended to copolymers, it was found that RAFT copolymers achieved greater cyclization intensities and improved thermal stability …

Low-Velocity Impact Analysis Of Composite Repair Patches Of Different Shapes, Sarvesh Baliga

Doctoral Dissertations and Master's Theses

The area under crack for various structures can be effectively repaired by the use of composite materials. Low velocity impact can cause barely visible damage to the interior structure of laminated composite. These impacts can cause delamination in composite materials. In this study, a Finite Element Analysis was conducted using Abaqus/Explicit and the results of the analysis were compared to the experimental data from literature. E-glass/epoxy composite laminate was subjected to a low velocity impact test. To study the effect of patch repair, a composite patch was applied on a cracked laminate and a low velocity impact was then conducted …

Volatile Condensible Material Deposition In Leo Simulated Environment, Jinya Pu

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Room Temperature Vulcanized (RTV) silicone and compounds are widely used in outer-space for bonding or potting spacecraft components. In geosynchronous equatorial orbit (GEO), the silicone may outgas species which can condense on optically sensitive surfaces and degrade their performance, therefore shortening the lifetime of spacecraft. In low-earth-orbit (LEO), the silicone rubber is subject to an energetic and corrosive environment. Atomic oxygen (AO) and ultraviolet radiation can cause abrasion and degradation of the silicone rubber, cause changes in existing condensed VCM films and affect the properties of VCM films condensing in this atmosphere. Experiments were performed to simulate GEO conditions. In …

Tension-Compression Fatigue Behavior Of 2d And 3d Polymer Matrix Composites At Elevated Temperature, Saleh A. Alnatifat

Theses and Dissertations

In this Research effort, the tension-compression fatigue behavior of the 3D and 2D PMCs with 0/90˚ fiber orientation (newly developed) was investigated. These polymer composites consist of an NRPE (high-temperature polyimide) matrix with carbon fiber reinforcement. Compressive properties were assessed at (1) room temperature and (2) elevated temperature with one side, Tright, at 329˚C and the other side open to the ambient air. Tension-compression fatigue tests were conducted at elevated temperature with a frequency of 1 Hz and a ratio of minimum to maximum stress of -1.

Characterizing Strain Accumulation, Residual Stress, And Microstructure Of Additive Manufactured Materials, Hannah K. Woods, Todd A. Book, Catalina Parada, Michael D. Sangid

The Summer Undergraduate Research Fellowship (SURF) Symposium

Additive Manufacturing (AM) is a rapidly evolving fabrication technology beneficial for its cost-saving potential to produce complex, low-volume shapes. However, AM materials are currently limited to nonstructural applications due to variability in their structural integrity, particularly their fatigue lives. IN718, Ti64, and Al10MgSi specimens manufactured by Direct Metal Laser Sintering (DMLS) were characterized based on variation of post-processing techniques and build direction. To understand the impact of each variable, surface roughness, hardness, residual stresses, microstructure, and strain accumulation in response to Low Cycle Fatigue (LCF) were studied. The use of Electron Backscatter Diffraction (EBSD) provided grain orientation and grain size …

Identifying And Correcting Biases In Digital Image Correlation At Multiple Length Scales, Catalina Parada, Alberto W. Da Silva Mello, Michael D. Sangid, Hannah K. Woods, Samuel E. Otto

The Summer Undergraduate Research Fellowship (SURF) Symposium

Accurate strain measurement at grain and sub-grain levels is important to predict and understand crack initiation during fatigue of materials. During cyclic loading, low magnitude strain is accumulated in the material and any distortion in the images can lead to inaccurate strain measurements and false prediction of the material’s behavior. Digital Image Correlation (DIC) is a reliable tool used to measure strain localization by correlating images before, during, and after cyclic loading. DIC tracks the deformation of nano/micro-scale patterns placed on the surface of the specimens to determine strain fields. However, DIC software does not account for biases due to …

The Robert & Esther Goddard Papers, Robert H. Goddard

Finding Aids

Dr. Robert H. Goddard was a member of the Clark Physics Department for 29 years. Foremost American pioneer of rocket research, he laid the technical and theoretical foundations for many of the developments in long-range rockets, missiles, satellites and space flight, which collectively put us into the Space Age.

The collection includes correspondence, diaries, journals, patent applications and awards, reports, and photographs. The collection also includes original paintings by Dr. Goddard.

Techniques For Payload Stabilization For Improved Photography During Stratospheric Balloon Flights, James Flaten, Christopher Gosch, Joseph (Benjamin) Habeck

2017 Academic High Altitude Conference

Payload-box rotation and swing are perennial challenges to achieving high-quality photography (typically videography) during weather-balloon flights to “near-space” (AKA the stratosphere). Continuous camera motion can lead to blurred still photos, nearly-impossible-to-watch video footage, and precludes time-exposure photography required for most astronomical imaging even though altitudes are reached where the daytime sky appears black. Apparently-random payload rotation, persisting even at altitude, can often exceed servo rotation rates and frustrate attempts to do active camera pointing. Here we discuss mostly-passive payload stabilization strategies we, and our collaborators, have used to mitigate and dampen both swing and rotation of suspended payloads on high-altitude …

Simulation Of Metal Particulates In High Energetic Materials, Eduardo Nieto

Theses and Dissertations

This research focused on analyzing the effects of aluminum in high explosives such as PBX9501 using the MPEXS computational simulation code for a wide range of metalized explosive cases. The varying parameters are aluminum particle diameter and mass fraction of aluminum. The addition of metal particulates in explosive mixtures increases the density of the shock wave, causing a higher pressure in the shock. It was concluded that pressure and density steadily increases as the Al particle diameter increases, and pressure and density decreases when Al mass fraction increases. The concentrated pressures will dissipate quickly due to the high density, providing …

Creep Of Sylramic-Ibn Fiber Tows At Elevated Temperature In Air And In Silicic Acid-Saturated Steam, Kevin B. Sprinkle

Theses and Dissertations

Stressed oxidation experiments on Sylramic-iBN fiber tows were performed to evaluate the novel fiber's mechanical performance, creep behavior, and creep mechanisms. This research effort investigated creep response of Sylramic-iBN fiber tows at elevated temperatures in both air and in silicic acid-saturated steam environments. Creep experiments were conducted at creep stresses ranging from 127 to 762 MPa at 400°C and 500°C in order to examine the mechanical behavior of the Sylramic-iBN fiber tows at temperatures below and above the melting point of boria (450°C). Sylramic-iBN fibers are known to have excellent creep resistance, better than most other non-oxide fibers and significantly …

Effect Of Prior Exposure At Elevated Temperatures On Tensile Properties And Stress-Strain Behavior Of Four Non-Oxide Ceramic Matrix Composites, Sarah M. Wallentine

Theses and Dissertations

Thermal stability of four non-oxide ceramic matrix composites was studied. The materials studied were commercially available composites: SiC/SiNC; C/SiC; C/SiC-B4C (C/HYPR-SiC^TM); and SiC/SiC-B4C (SiC/HYPR-SiC^TM). COI Ceramics manufactured the SiC/SiNC and C/SiC composites using polymer infiltration and pyrolysis (PIP). The C/HYPR-SiC^TM and SiC/HYPR-SiC^TM CMCs were manufactured by Hyper-Therm High-Temperature Composites using chemical vapor infiltration (CVI). All four composites rely on a dense matrix for strength, stiffness, and oxidation protection. Fiber coating provides a fiber-matrix interface that allows fiber-matrix debonding and fiber pullout to occur, imparting fracture toughness to the CMC. The SiC/SiNC, C/SiC, and C/HYPR-SiC …

Automatic Building Change Detection In Wide Area Surveillance, Paheding Sidike, Almabrok Essa, Fatema Albalooshi, Vijayan K. Asari, Varun Santhaseelan

Electrical and Computer Engineering Faculty Publications

We present an automated mechanism that can detect and characterize the building changes by analyzing airborne or satellite imagery.

The proposed framework can be categorized into three stages: building detection, boundary extraction and change identification. To detect the buildings, we utilize local phase and local amplitude from monogenic signal to extract building features for addressing issues of varying illumination. Then a support vector machine with Radial basis kernel is used for classification. In the boundary extraction stage, a level-set function with self-organizing map based segmentation method is used to find the building boundary and compute physical area of the building …

Characterization Of Laser Deposited Ti-6al-4v To Nb Gradient Alloys, Clincy Cheung

Materials Engineering

An alloy was fabricated with Ti-6Al-4V and Nb powder using laser deposition (LD) to form a compositional gradient. The gradient was deposited, starting with Ti-6Al-4V powder, onto a forged Ti-6Al-4V substrate in an Argon environment. Niobium (Nb) composition increased by 4-at.% with each layer deposited until the composition reached 100-at.% Nb. This process yielded steep thermal gradients and affected the microstructure and mechanical properties across the compositional gradient. To observe the microstructural changes in the alloy, an etched gradient was viewed with optical microscopy at 1000x, where the grain structure was observed to be an acicular α phase at 100-at.% …

Structural Micrometeoroid And Radiation Shielding For Interplanetary Spacecraft, Jared Allen Ruekberg

Master's Theses

This paper focused on two significant space forces that can affect the success of a spacecraft: the radiation and micrometeoroid environments. Both are looked at in the context of the region of space between Earth and Mars. The goal was create reference environments, to provide context to results of environmental modeling, and to provide recommendations to assist in early design decisions of interplanetary spacecraft. The radiation section of this report used NASA's OLTARIS program to generate data for analysis. The area of focus was on the radiation effects for crewed missions, therefore effective dose equivalent was the metric used to …

Hybrid Rocket Motor Scaling Process, Joseph B. R. Vanherweg

Master's Theses

Hybrid rocket propulsion technology shows promise for the next generation of sounding rockets and small launch vehicles. This paper seeks to provide details on the process of developing hybrid propulsion systems to the academic and amateur rocket communities to assist in future research and development. Scaling hybrid rocket motors for use in sounding rockets has been a challenge due to the inadequacies in traditional boundary layer analysis. Similarity scaling is an amendment to traditional boundary layer analysis which is helpful in removing some of the past scaling challenges. Maintaining geometric similarity, oxidizer and fuel similarity and mass flow rate to …

Coreless Planar Transformer Using Low-Temperature Co-Fired Ceramics For Isolated Gate Driver Applications, Matthew W. Feurtado

Electrical Engineering Undergraduate Honors Theses

The aim of this thesis project is to design a signal isolation transformer for gate driver applications using coreless planar transformers (CPT) on a low-temperature co-fired ceramic (LTCC) substrate. To achieve this goal a modulator-demodulator circuit will be selected from several existing designs and an isolation transformer will be designed as a CPT to produce a high frequency high temperature signal isolation for gate driver applications in switching converters, audio drivers, and motor drives. Several designs for coreless planar transformers will be evaluated and tested, and the results will be compared to the theoretical performance obtained from SPICE models for …

A Study On The Micro Electro-Discharge Machining Of Aerospace Materials, Mychal-Drew Moses

Masters Theses & Specialist Projects

Electrical Discharge Machining (EDM) is a non-traditional machining process that uses hundreds of thousands of minute electrical sparks per second to machine any electrically conductive material, no matter the hardness or how delicate it is. EDM allows a much greater range of design possibilities, unconstrained from the traditional machining processes, in which material is removed mechanically by either rotating the cutting tool or the work piece. Shapes that were impossible to machine by any other method, such as deep, precision, square holes and slots with sharp inside corners, are readily produced. It provides accurate geometries in high- aspect ratio holes …

A Comparative Study On Micro Electro-Discharge Machining Of Titanium Alloy (Ti-6al-4v) And Shape Memory Alloy (Ni-Ti), Pegah Kakavand

Masters Theses & Specialist Projects

The purpose of this research was to investigate the surface modifications that take place during the machining of NiTi SMA and Ti-6Al-4V with micro-EDM. This was done by creating an array of blind holes and micro-patterns on both work-pieces. To analyze the machined surface and investigate the results, scanning electron microscope (SEM), energy dispersive X- ray spectroscopy (EDS) and X-ray diffraction (XRD) techniques were employed. In addition, the effects of various operating parameters on the machining performance was studied to identify the optimum parameters for micro-EDM of NiTi SMA and Ti-6Al-4V. Recently, aerospace and biomedical industries have placed a high …

Phased Array Beamsteering In Composite Laminates For Guided Wave Structural Health Monitoring, Peter Osterc

Doctoral Dissertations and Master's Theses

In this study a guided wave phased array beamsteering approach is applied to composite laminates. Current beamsteering algorithms derived for isotropic materials assume omnidirectional wave propagation. Due to inherent anisotropy in composites, guided wave propagation varies with direction and wavefronts no longer have perfect circular shapes.

By examining slowness, velocity and wave curves, as well as amplitude variation with direction for a given composite laminate, the wavefront from a single source can be described as a function of the angle of propagation and distance from origin. Using this approach, a more general delay and sum beamforming algorithm for composite laminates …

Non-Destructive Techniques For Classifying Aircraft Coating Degradation, Kody A. Wilson

Theses and Dissertations

In this research non-destructive techniques were examined as possible methods of determining aircraft coating degradation. Single Value Decomposition(SVD)-Linear Discriminant Analysis(LDA) algorithms were applied to measured spectra. When applied to infrared emittance spectra only 52% classification accuracy was achieved. When applied to Raman spectroscopy a higher classification accuracy of 70.4% is attained when using the same SVD-LDA algorithm. However the best performing measurement was using infrared reflectance classification accuracies were 100%, 99.83% and 94.4% when using the Bomem FTS, DRIFTS and Telops respectively for one of the sample sets. For DRIFTS data a more accurate fingerprint region was identified 865.6 - …

Methods Of Measuring Stress Relaxation In Composite Tape Springs, Justin T. Heppe

Theses and Dissertations

Composite tape springs present an opportunity to use stored energy for the deployment of space structures. Concern has risen over the dissipation of strain energy during storage due to viscoelasticity inherent in polymeric materials commonly used as the composite matrix. Tests to measure the internal behavior of a composite tape spring over time are conducted along with methods of analyzing and fitting the resulting data. The three constant strain configurations tested were compression force of the cross section, a restraining force of a longitudinal fold, and the change in shape of a folded section. While the shape changing test did …

Effect Of Prior Exposure At Elevated Temperatures On Tensile Properties And Stress-Strain Behavior Of Three Oxide/Oxide Ceramic Matrix Composites, Christopher J. Hull

Theses and Dissertations

Thermal stability of three oxide-oxide ceramic matrix composites was studied. The materials studied were Nextel^TM610/aluminosilicate (N610/AS), Nextel^TM720/aluminosilicate (N720/AS), and Nextel^TM720/Alumina (N720/A), commercially available oxide-oxide ceramic composites (COI Ceramics, San Diego, CA). The N610/AS composite consists of a porous aluminosilicate matrix reinforced with laminated woven alumina N610 fibers. The N720/AS and N720/A composites consist of a porous oxide matrix reinforced with laminated, woven mullite/alumina (Nextel^TM720) fibers. The matrix materials are aluminosilicate in N720/AS and alumina in N720/A. All three composites have no interface between the fibers and matrix, and rely on the porous …

Tension-Compression Fatigue Of An Oxide/Oxide Ceramic Matrix Composite At Elevated Temperature In Air And Steam Environments, Richard L. Lanser

Theses and Dissertations

Tension-compression fatigue behavior of an oxide-oxide ceramic matrix composite was investigated at 1200°C in air and steam. The composite is comprised of an alumina matrix reinforced with Nextel 720 fibers woven in an eight harness satin weave. The composite relies on a porous matrix for damage tolerance. Compression and tension tests to failure were conducted to characterize basic mechanical properties. Tension-compression fatigue tests were performed at 1 Hz frequency with a ratio of minimum to maximum stress of -1. Maximum stresses ranged from 60-120 MPa. Fatigue run-out (defined as 105 cycles) was achieved in air at 80 MPa and in …

Mechanical Testing Of Ultra-High Temperature Ceramics At 1500°C In Air -Development Of An Experimental Facility And Test Method, Sheena L. Winder

Theses and Dissertations

With a melting point in excess of 3000°C and a high density, ultra-high temperature ceramics (UHTCs) are a candidate material for hypersonic flight vehicles, atmospheric re-entry vehicles, and rocket propulsion systems. When ceramics are under consideration as a structural material, creep is an important design criterion and a life-limiting condition. However, the characterization of mechanical behavior at temperatures in excess of 1300°C has many challenges to overcome. Of utmost importance is the selection of materials for test fixtures. Materials selected must maintain their structural integrity, not cause chemical degradation of the test material, and not interfere with the acquisition of …

Effect Of Sustainable And Composite Materials On The Mechanical Behavior Of Sandwich Panels Under Edgewise Compressive Loading, Justin A. Tafoya

Master's Theses

Over the last three decades, the aerospace industry has gradually shifted from metals to composites in many different applications due to the lightweight properties of composite materials. Some benefits of composites include higher strength-to-weight ratio and corrosion resistance. At this point in time, the composite industry researchers are focusing on renewable and sustainable materials (bio-composites). By understanding the structural capabilities of bio-composites that have been used for centuries, new developments of sustainable materials will spark more interest throughout the industry. Bio-composites include fibers such as hemp, bamboo, flax, etc. The high demand for bio-composites in composite structures can also reduce …

Suborbital Spaceflight: A Student Team’S Plan To Send A Rocket To Space, Bryce Chanes, William Carpenter, Julio Benavides, Matthew Haslam, Brenda Haven

Aviation / Aeronautics / Aerospace International Research Conference

The Eagle Space Flight Team was created with the goal of becoming the first undergraduate team to design, build, and launch a rocket capable of suborbital spaceflight. In order to achieve this goal, the team will have to design a rocket capable of atmospheric flight at speeds over Mach 5 and launch it on one of the largest amateur rocket motors ever made. Over the next three years, the team will progress towards accomplishing this feat through a series of incremental test flights. Before the space flight, the team will build three sub-scale rockets designed to reach altitudes of 30,000’, …

A Multi-Scale Based Model For Composite Materials With Embedded Pzt Filaments For Energy Harvesting, A.E. El-Etriby, M.E. Abdel-Meguid, K.M. Shalan, Tarek Hatem, Yehia Bahei-El-Din

Centre for Advanced Materials

Ambient vibrations are major source of wasted energy, exploiting properly such vibration can be converted to valuable energy and harvested to power up devices, i.e. electronic devices. Accordingly, energy harvesting using smart structures with active piezoelectric ceramics has gained wide interest over the past few years as a method for converting such wasted energy. This paper provides numerical and experimental analysis of piezoelectric fiber based composites for energy harvesting applications proposing a multi-scale modeling approach coupled with experimental verification. The multi-scale approach suggested predicting the behavior of piezoelectric fiber-based composites use micromechanical model based on Transformation Field Analysis (TFA) to …

Shape Memory Behavior Of Single Crystal And Polycrystalline Ni-Rich Nitihf High Temperature Shape Memory Alloys, Sayed M. Saghaian

Theses and Dissertations--Mechanical and Aerospace Engineering

NiTiHf shape memory alloys have been receiving considerable attention for high temperature and high strength applications since they could have transformation temperatures above 100 °C, shape memory effect under high stress (above 500 MPa) and superelasticity at high temperatures. Moreover, their shape memory properties can be tailored by microstructural engineering. However, NiTiHf alloys have some drawbacks such as low ductility and high work hardening in stress induced martensite transformation region. In order to overcome these limitations, studies have been focused on microstructural engineering by aging, alloying and processing.

Shape memory properties and microstructure of four Ni-rich NiTiHf alloys (Ni50.3Ti29.7Hf20, Ni50.7Ti29.3Hf20, …

Design Of The Structural And Propulsion Systems For The 2015 University Of Akron Rocket Team, Kyle W. Dehoff, Nicholas J. Hrusch

Williams Honors College, Honors Research Projects

No abstract provided.