Structures and Materials Commons^™

Direct Ink Writing Of Functional Fiber/Granular Composites, Zhuoyuan Yang

Doctoral Dissertations and Master's Theses

Direct ink writing provides a versatile manufacturing route for fabricating functional fiber and granular composites with controlled architecture, tunable interfaces, and customized material distributions. Fiber reinforced composites offer high stiffness, strength, fatigue resistance, and functional anisotropy, while granular composites provide scalable access to particle based structures with high material efficiency and broad resource compatibility. However, the additive manufacturing of these composite systems remains challenging. For fiber based composites, precise control of fiber placement, matrix impregnation, interfacial bonding, and freestanding deposition is difficult to achieve during printing. For granular composites, stable particle flow, controllable packing, binder infiltration, and shape retention are …

Detecting And Repairing Conflicting Constraints In Co-Trained Physics-Informed Neural Networks For Composite Curing Processes, Cooper J. Evans

Dissertations, Master's Theses and Master's Reports

Composite materials have become a critical component of modern manufacturing, especially in the automotive and aerospace industries. The curing process for these composites has been modeled using a variety of partial differential equations representing the heat transfer and composite curing kinetics. Optimizing the applied temperature profile is critical for maximizing the efficiency and capacity of composite part manufacturers. Constraints must be placed on the inputs and outputs of the model, including but not limited to, the applied temperature profile, part temperature, and final degree of cure. Conflicting sets of constraints are easy to unknowingly impose due to the highly coupled …

Buckling Analysis Of Auxetic Composite Laminates And Optimal Design Using Lamination Parameters And Machine Learning, Hans Bendon Maria Tamil Selvan

Mechanical and Aerospace Engineering Theses

Composite materials are widely used as structural panels in aerospace, automotive, and civil engineering applications, where buckling is often a critical failure mode. This thesis focuses on the analysis and design of composite laminates that maximize buckling performance under prescribed stiffness and thickness constraints.

The first part of the study investigates the buckling behavior of auxetic laminates, which exhibit a negative Poisson's ratio. While previous studies suggest that auxetic laminates can achieve higher critical buckling loads than non-auxetic laminates under simply supported boundary conditions with lateral restraint, the influence of other boundary conditions and plate aspect ratios has not been …

Made On Mars: Design And Manufacturing Of Structural Polymer-Regolith Composites, Pailey M. Vitale

Williams Honors College, Honors Research Projects

Human exploration of Mars is constrained by harsh environmental conditions and the prohibitive cost of transporting materials from Earth. Long-term sustainability requires the local production of mechanical and structural components using resources available on Mars, thereby minimizing payload mass. This project investigates polymer–regolith composites derived from atmospheric CO₂ and mineral-rich regolith as a pathway toward in-situ manufacturing. These composites, when compatible with additive manufacturing, could replace imported plastics, enable on-demand fabrication, and support closed-loop recycling systems. The objective is to design and evaluate polymer–regolith composites that maintain mechanical integrity and environmental resistance under Martian conditions, including extreme temperature swings, radiation …

Design New Stage For Vacuum Pin On Disk, Miranda Boyd

Williams Honors College, Honors Research Projects

For my senior design project, I am redesigning the moving stage for the vacuum pin-on-disk test used in the Akron Engineering Tribology Lab. This system is used to evaluate bearings and lubricants for aerospace applications under controlled vacuum conditions. The current stage design limits flexibility when adjusting for different testing parameters, so my goal is to develop a new movable stage that allows for varying weights and loads to be applied accurately and safely. The redesigned stage will improve test efficiency, adaptability, and precision, ensuring the system can accommodate a wider range of experimental conditions and materials while maintaining compatibility …

Breaking The Vapor Barrier And Scale: Revolutionizing Steel Quenching With Ultrasound Technology, Anthony O. Santos

Williams Honors College, Honors Research Projects

The quenching process is a fundamental heat treatment used to enhance material properties by heating steel to its austenitizing temperature and rapidly cooling it to form high-strength martensite. However, this process is often hindered by two surface barriers: the Leidenfrost effect (vapor blanket) and oxide scale. These cooling limitations restrict the use of steel in high-performance aerospace applications due to inconsistent material properties and unpredictable engineering properties. This research investigates the use of fully submersible, 50-watt 40 kHz ultrasound technology to improve cooling rates in a Jominy test [4]. Through numerical simulations and experimental validation, the study demonstrates that acoustic …

Optimization Of Post-Processing Methods For Additively Manufactured Metals, Julia R. Carano

Williams Honors College, Honors Research Projects

Ultrasonic Nanocrystal Surface Modification (UNSM) is a process used to change the surface hardness of flat-faced materials. It is a machining process using a high-powered laser and a blunt-tipped tool at high speeds which aims to improve the uniformity of the surface on most metals. By heating and pressing the surface of the workpiece, the grains of the material become less rounded and more cohesive on a microscopic level. This, ideally, results in a workpiece with improved material properties. The changes were previously observed through hardness testing.

Fused Filament Fabrication Additive Manufacturing Of 17-4 Ph Stainless Steel: Process–Structure–Property Relationships In Magnetic Materials, Maanav Patel

Theses and Dissertations

Additive manufacturing (AM) enables the fabrication of complex metallic components through layer-by-layer processing directly from digital models. Among AM techniques, material extrusion–based processes such as fused filament fabrication (FFF) provide an accessible method for producing metal parts using filament feedstocks composed of metal powders and polymer binders. When applied to precipitation-hardening stainless steels such as 17-4 PH, the processing route and heat treatments can influence the resulting microstructure and functional properties. This work investigates the magnetic behavior of 17-4 PH stainless steel fabricated using FFF and evaluates how heat treatment conditions influence measured magnetic properties. Samples were produced and analyzed …

In-Situ Investigations Of Calcium-Magnesium-Aluminosilicates (Cmas) Infiltration Effects On Thermal Barrier Coatings Under Extreme Environments Replicating Jet Engines, Zachary Stein

Doctoral Dissertations and Master's Theses

Calcium-magnesium-aluminosilicate (CMAS) particulates, such as sand or volcanic ash, are ingested by gas turbine jet engines during operation. When operating within high abundance regions, these particulates negatively interact and degrade the high temperature thermal barrier coatings (TBC) protecting underlying superalloy turbine blades vital to engine operation. These CMAS particulates melt within the engine and infiltrate into the ceramic coatings. In electron-beam physical vapor deposited (EB-PVD) TBCs, the CMAS within the intercolumnar gaps stiffens the coatings and causes thermomechanical induced high stress concentrations, risking crack formation. While molten, the CMAS thermochemically alters and destabilizes the coating, also risking coating failure. Premature, …

Extraction Of Aluminum From Lunar Regolith Through Molten Salt Electrolysis, Jacob N. Ortega, Todd P. Sander, Jeffrey D. Smith, Fateme Rezaei, David J. Bayless, William Schonberg, Daniel S. Stutts, Frank D. Han

Materials Science and Engineering Faculty Research & Creative Works

This paper presents the methodology, development, and results of an end-to-end regolith-to-metal concept for producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method. Using electrolytic reduction, aluminum oxide (i.e., alumina) can be reduced into aluminum and oxygen via electrolysis in a molten salt bath. A steady supply of hydrogen chloride could allow this in-situ resource utilization (ISRU) method to supply several necessary materials consumed in the electrolytic reduction step of the process to produce bulk aluminum metal, oxygen, water, and silica from anorthite abundant in lunar highland regions. In this …

Improvement Of The Fatigue Behaviour Of Additive Manufatured Scalmalloy By Using Surface Improvement Processes, Francisco José Boby Alcaide, Irene Eras, José Manuel De Los Santos, Alejandro Munoz Castro, Antonio Perinan Butrón, Jorge Sogorb

15th International Conference on Shot Peening

The use of light metals such as Aluminum alloys has experienced a remarkable increase for the additive manufacturing (AM) industry, especially in aerospace.

AM Scalmalloy®. (an Al-Mg-Sc alloy) shows outstanding behavior with much higher mechanical performance with respect to other alloys for powder bed fusion laser-based (PBF-LB) process like AlSi10Mg or AlSi7Mg. Recent studies have mainly focused on static loading, with minor attention to cyclic loading despite its vital importance in many applications.

In this work, the fatigue performance of PBF-LB Scalmalloy was investigated considering the effects of surface treatments to identify the set of optimal post-processes. Shot peening with …

Methodologies And Applications Of Precision Shot Peening To Hole Or Slot Geometry, James C. Hoffman

15th International Conference on Shot Peening

Shot peening, a commonly used method of fatigue and surface enhancement, is a critical process in many of the components in the aerospace industry. When it comes to small holes and/or slot geometries in these components, the process can become a challenge when these features are smaller than a conventional size Almen strip. In these cases, a decision must be made about how to process this type of geometry. Oftentimes, the method to apply the shot peen process is already defined in a process specification or part print so we must adhere to that method. If a method is not …

Improving Fatigue Strength And Life Of Single Crystal Cmsx-4, Jochen Peter Fuhr, Lloyd Hackel, Nicolau I. Morar, Noah Holtham, Keivan Davami, Montu Sharma, Rajkumar Roy

15th International Conference on Shot Peening

The deep penetration of laser peening (LP) and retention of residual stress at high temperature by LP is significant in improving fatigue life and strength of superalloys exposed to high temperature and corrosion. Single crystal CMSX-4, was evaluated for stress relaxation and both fatigue life and fatigue strength of material that was LP-treated compared to non-LP and shot-peened (SP) specimens. LP was done with multiple layers using a 20 J/pulse laser where the laser high energy enabled using a 5 mm spot size on the metal surface. Stress measurements by the slitting technique showed the plastic penetration depth exceeded SP …

Tensile Creep Of A Hybrid Polymer-Matrix/Ceramic-Matrix Composite At Elevated Temperature, Waleed S. Alshehri

Theses and Dissertations

Advanced aerospace systems require structural materials that can perform reliably in high-temperature environments for long durations. The performance of standard polymer matrix composites (PMCs) in these conditions is often limited by their susceptibility to time-dependent deformation, such as creep. The objective of this research is to characterize the high-temperature creep behavior of a novel unitized material system comprising a polymer matrix composite (PMC) and a ceramic matrix composite (CMC) co-cured together. The PMC part consists of the polyimide matrix reinforced with laminated carbon fibers woven in an eight harness satin weave (8HSW). The CMC part consists of a zirconia-based ceramic …

Mno2 Nanoscale Interface Modification, Alexander C. Skoppe

Doctoral Dissertations and Master's Theses

Interface modification of carbon fibers has been shown to improve the mechanical performance of composites. In addition, interface modification of carbon fiber composites can impart multifunctionality into the resulting composite. This work will explore ZnO and MnO2 as interface modifications for use on carbon fibers. When exposed to high temperatures, carbon fibers undergo fiber degradation, leading to the need for low-temperature hydrothermal processes. This work will develop and characterize a nanoscale ZnO and MnO2 interface modification for use on carbon fibers. These nanomodifications will be developed with low-temperature processes, minimizing the fiber degradation that the fibers undergo. Fourier transform infrared …

In-Situ Defect Detection In Selective Laser Melting Using Convolutional Neural Networks, Ethan Gaigalas

Master's Theses

This thesis develops and trains a convolutional neural network (CNN) to classify defects in metal parts produced by selective laser melting (SLM) using acoustic emission (AE) data. The model successfully identified porosity and standard build layers with high accuracy but consistently struggled to classify lack of fusion (LOF) defects, regardless of input type, normalization, or class count. These results suggest that while AE signals contain distinguishable features for certain defect types, LOF signals may be too subtle or inconsistent for reliable detection. The study addresses the ongoing challenge of in-situ quality monitoring in metal additive manufacturing, where defects like cracks, …

Investigation Into Silicone-Silicate Conversion Due To Atomic Oxygen In The Low Earth Orbit Environment, Justin T. Self

Master's Theses

Silicones have been widely used over the years in spacecraft for a variety of functions, but atomic oxygen (AO) exposure in Low Earth Orbit causes a silicate (SiO₂) surface layer to rapidly develop on the silicone which results in a permanent change in its thermal and optical properties. Although this silicone to silicate conversion is known to occur, statistical predictions of layer formation as a function of time on orbit are not found in literature. This thesis utilized optical and scanning electron microscopy, Fourier-Transform Infrared Spectroscopy, diffuse reflectance spectroscopy, and nonlinear regression statistical techniques after RF plasma asher …

Model-Based Design Of Compressed Lithium-Metal Pouch Cell Battery Modules For Evtol Applications, Scott J. Stirling

Master's Theses

Batteries with higher specific energy and power are essential for extending the range and performance of electric vertical takeoff and landing aircraft (eVTOLs). Anode-free lithium-metal pouch cells offer strong potential at the cell-level but require high compressive pressures to enhance cycle life and discharge performance. These pressures necessitate heavier structural components, reducing packaging efficiency at the module level.

To evaluate this tradeoff, a full-factorial enumeration model was developed to explore viable module designs within a constrained packaging volume. The model scales subsystem masses, enforces design rules and material limits, and accounts for large (~20%) cell thickness changes during cycling.

Results …

Exploring Metal Additive Manufacturing In Martian Atmospheric Environments, Zane Mebruer

Mechanical Engineering Undergraduate Honors Theses

On-surface manufacturing is key to the success of a planetary colonization, especially that of Mars. However, traditional subtractive manufacturing processes are equipment, energy, and material intensive, meaning novel additive manufacturing (AM) processes must be pursued for this end. Selective laser melting, one of the most effective and versatile AM methods, would be incredibly beneficial to a Martian mission but requires an artificial argon atmosphere to create effective parts. The purpose of this study was to examine if carbon dioxide, the gas that makes up over 95% of Mars’ surface atmosphere, would be a sufficient substitute for argon in SLM fabrication. …

Characterizing Heating And Resistance Properties Of Nichrome Burn Wire To Be Used In Cubesat Actuation, Noah Moix

Mechanical Engineering Undergraduate Honors Theses

This thesis investigates the use of Nichrome 60 wire as a burn wire mechanism, commonly utilized in CubeSats and other aerospace engineering applications requiring precise, single-use release systems. The experiment focused on characterizing the thermal and resistive behavior of Nichrome 60 wire under Joule heating conditions. Four wire configurations were tested: 34-gauge and 36-gauge wires, each at lengths of 1 inch and 2 inches. Each configuration was subjected to a constant current until thermal failure occurred. During testing, real-time measurements of electrical resistance and wire temperature were recorded. This data was used to generate resistance vs. temperature profiles for each …

Thermal Characterization Of 3d Printing Materials For Increasing Insulation Potential And Practicality, Jackson H. Minnick

Mechanical Engineering Undergraduate Honors Theses

This study served as an exploration into the possible existence of a correlation between the infill lattice structure of a 3D printed wall section and the thermal performance of that sample as characterized by thermal conductivity measured in units of Watts per meter Kelvin. With the continual increase in the practicality, fidelity, and applicable fields of additive manufacturing, namely FDM 3D printing, research on specific print characteristics and their effects on the material and thermal characteristics of the part in question is steadily becoming more commonplace. Although the thermal conductivity of 3D printed wall sections as a function of infill …

Graphene-Polymer Nanocomposite For Electromagnetic Interference Shielding, Ravi Venkata Surya Sai Mogilisetti

Mechanical and Aerospace Engineering Theses - Archive

Polymers have widespread usage in most industries, such as aerospace, automotive, telecommunications, and medicine, mainly because they have a positive lightweight nature and excellent mechanical properties. One significant advantage of polymeric materials is their ability to combine nano-fillers, greatly enhancing their mechanical, electrical, and thermal properties. In the category of polymer matrices, polypropylene (PP) is notable for its low cost, ease of processing, and balanced mechanical properties. However, its relatively lower modulus and strength limit their applications in high-performance engineering. This research explores the addition of graphene into polypropylene to improve its mechanical properties and establish a conductive network for …

Linking Molecular Structure Evolution To Mechanical Degradation During Environmental Aging In Conventional And Recyclable Epoxy Systems, Ben T. Jewell

Dissertations, Master's Theses and Master's Reports

The long-term performance of polymeric materials in extreme environments is governed by complex chemical and physical aging processes that alter their molecular structure and mechanical integrity. Conventional thermoset epoxies, while widely used in structural applications, are particularly susceptible to oxidative degradation at elevated temperatures, leading to embrittlement and loss of structural integrity. In the first part of this work, diffusion-limited oxidation (DLO) in a bulk structural epoxy was systematically investigated to establish the link between heterogeneous microstructural evolution and macroscopic mechanical degradation. High-temperature oxidation experiments were conducted in a controlled environmental chamber, and the resulting chemical, thermal, and mechanical changes …

Novel Design And Fabrication Of A High-Speed Transient Heat Flux Sensor For Application To Rotating Detonation Engines, Zachary Todd Tallman

Graduate Theses, Dissertations, and Problem Reports (ETD)

Rotating detonation engine (RDE) combustion systems have been a topic of interest in the pressure gain combustion community for their benefits over traditional gas turbine engine combustors. However, cooling requirements for these engines are significantly higher and less predictable than those of non-detonating engines. To understand and quantify the high-speed heat transfer dynamics within an RDE, a novel high-frequency heat flux sensor is presented. This study aims to design a robust, single-sided sensor that can withstand the high temperature and harsh environment of an RDE for extended durations. Screen printing is used to deposit a layered, platinum-yttria-stabilized zirconia (YSZ) film …

Ground Testing Of A Magnetic-Electrostatic Separation System For Lunar Regolith Beneficiation, Peter Bachle, Charles Wood, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

The separation of lunar regolith by mineral composition and size category is useful forin-situ resource utilization (ISRU). The research presented herein discusses the designing and development of equipment that has the potential to separate lunar regolith into aluminum, iron-titanium, and magnesium-iron ores. Along with the metal ore separation, this equipment shows the potential to separate regolith by size categories. The combined effect of these separation methods generates output that is valuable to subsequent use in metal and oxygen extraction, additive manufacturing, and regolith sintering processes. The designed equipment uses a dual-strength magnet system with N42 and N52 neodymium magnets for …

Gas-Generating Reactive Materials: Design, Evaluation And Effect Of Morphology On Their Ignition And Combustion, Purvam Mehulkumar Gandhi

Dissertations

This work investigates optimizing gas-generating reactive materials, focusing on particle morphology's effect on ignition and combustion behavior. Metal-based gas-generating energetic materials (EMs) are promising alternatives to replace traditional CHNO compounds. Design of advanced metal-based EMs requires consistent ways of evaluating how their characteristics affect their ignition and combustion. Many relevant evaluation approaches exist; however, the results may be difficult to compare directly across different studies. Commonly, experimentalists ignite metal-based EMs in enclosed chambers and report pressures, P. However, direct comparison of these pressures is hindered by variations in the chamber volume, V, and the EM mass, m. To standardize the …

Kinetic Modeling Of Dust Grain Dynamics In Electrostatic Sieving, Aaron Berkhoff, Easton Ingram, Fateme Rezaei, Jeffrey Smith, David Bayless, William Schonberg, Daoru Han

Chemical and Biochemical Engineering Faculty Research & Creative Works

A new kinetic particle modeling framework was developed to investigate electrostatic transport of lunar regolith dust particles with applications to the concept of electrostatic sieving. the new approach is based on kinetic particle dynamics and includes major modules of sampling the particle size distribution, solving electric fields, and tracking motion of charged dust grains. a case study for a concept of electrostatic sieving was chosen to validate the new model. the simulation achieved similar performance of particle size classification as reported in the literature. the new model is computationally efficient (takes a few minutes on a PC-type laptop computer) so …

Development And Processing Of Shape Memory Polymer Composites (Smpcs) For Application In Structural Robotics And Robotic Sensors., Kavish Sudan

Electronic Theses and Dissertations

Shape Memory Polymers (SMPs) have attracted significant attention since their introduction in the 1980s due to their remarkable ability to regain their original shape from a temporarily deformed state when exposed to an external stimulus, typically heat. This shape memory effect, driven by thermal transitions such as the glass transition temperature (T_g) or melting temperature (T_m), has made SMPs highly attractive for applications in soft robotics, aerospace, and biomedical devices. However, SMPs face challenges such as limited mechanical strength, thermal stability, and electrical conductivity, which hinder their broader adoption in advanced applications. To address these challenges, …

Tension–Compression Fatigue Of A Hybrid Polymer-Matrix/Ceramic-Matrix Composite At Elevated Temperature, Marina B. Ruggles-Wrenn, Joshua Schmidt

Faculty Publications

Fully reversed tension–compression fatigue of a hybrid material comprising polymer matrix composite (PMC) co-cured with a ceramic matrix composite (CMC) was investigated. The PMC portion had a polyimide matrix reinforced with 15 plies of carbon fibers woven in an eight-harness satin weave (8HSW). The CMC portion had three plies of a quartz-fiber 8HSW fabric in a zirconia-based ceramic matrix. The hybrid PMC/CMC was developed for use in aerospace thermal protection systems (TPS). Hence, the experimental setup aimed to simulate the TPS service environment—the CMC side was kept at 329 °C, whereas the PMC side was open to laboratory air. Compression …

A Comprehensive Investigation Of The Influence Of Geometric Structure On The Shape Memory Performance Of Nafion, Jade Thomas

Physics Undergraduate Honors Theses

While perfluorosulfonic acid (PFSA) membranes have primarily been used in fuel cells due to their chemical, thermal, and mechanical stability, one PFSA, Nafion, boasts two unique characteristics: a broad glass transition (~55 °C to 130 °C) and a temperature-persistent electrostatic network. The combination of these two characteristics endows Nafion with exceptional shape memory properties – the ability of a material to morph and transform into pre-programmed shapes when exposed to an external stimulus – with enhanced permanent shape memorization, and a potentially near-infinite number of temporary shape memorization. This study focused on expanding the base of knowledge surrounding Nafion’s shape …