Structures and Materials Commons^™

Direct Ink Writing Of Functional Fiber/Granular Composites, Zhuoyuan Yang

Doctoral Dissertations and Master's Theses

Direct ink writing provides a versatile manufacturing route for fabricating functional fiber and granular composites with controlled architecture, tunable interfaces, and customized material distributions. Fiber reinforced composites offer high stiffness, strength, fatigue resistance, and functional anisotropy, while granular composites provide scalable access to particle based structures with high material efficiency and broad resource compatibility. However, the additive manufacturing of these composite systems remains challenging. For fiber based composites, precise control of fiber placement, matrix impregnation, interfacial bonding, and freestanding deposition is difficult to achieve during printing. For granular composites, stable particle flow, controllable packing, binder infiltration, and shape retention are …

Buckling Analysis Of Auxetic Composite Laminates And Optimal Design Using Lamination Parameters And Machine Learning, Hans Bendon Maria Tamil Selvan

Mechanical and Aerospace Engineering Theses

Composite materials are widely used as structural panels in aerospace, automotive, and civil engineering applications, where buckling is often a critical failure mode. This thesis focuses on the analysis and design of composite laminates that maximize buckling performance under prescribed stiffness and thickness constraints.

The first part of the study investigates the buckling behavior of auxetic laminates, which exhibit a negative Poisson's ratio. While previous studies suggest that auxetic laminates can achieve higher critical buckling loads than non-auxetic laminates under simply supported boundary conditions with lateral restraint, the influence of other boundary conditions and plate aspect ratios has not been …

Made On Mars: Design And Manufacturing Of Structural Polymer-Regolith Composites, Pailey M. Vitale

Williams Honors College, Honors Research Projects

Human exploration of Mars is constrained by harsh environmental conditions and the prohibitive cost of transporting materials from Earth. Long-term sustainability requires the local production of mechanical and structural components using resources available on Mars, thereby minimizing payload mass. This project investigates polymer–regolith composites derived from atmospheric CO₂ and mineral-rich regolith as a pathway toward in-situ manufacturing. These composites, when compatible with additive manufacturing, could replace imported plastics, enable on-demand fabrication, and support closed-loop recycling systems. The objective is to design and evaluate polymer–regolith composites that maintain mechanical integrity and environmental resistance under Martian conditions, including extreme temperature swings, radiation …

Improving Fatigue Strength And Life Of Single Crystal Cmsx-4, Jochen Peter Fuhr, Lloyd Hackel, Nicolau I. Morar, Noah Holtham, Keivan Davami, Montu Sharma, Rajkumar Roy

15th International Conference on Shot Peening

The deep penetration of laser peening (LP) and retention of residual stress at high temperature by LP is significant in improving fatigue life and strength of superalloys exposed to high temperature and corrosion. Single crystal CMSX-4, was evaluated for stress relaxation and both fatigue life and fatigue strength of material that was LP-treated compared to non-LP and shot-peened (SP) specimens. LP was done with multiple layers using a 20 J/pulse laser where the laser high energy enabled using a 5 mm spot size on the metal surface. Stress measurements by the slitting technique showed the plastic penetration depth exceeded SP …

Mno2 Nanoscale Interface Modification, Alexander C. Skoppe

Doctoral Dissertations and Master's Theses

Interface modification of carbon fibers has been shown to improve the mechanical performance of composites. In addition, interface modification of carbon fiber composites can impart multifunctionality into the resulting composite. This work will explore ZnO and MnO2 as interface modifications for use on carbon fibers. When exposed to high temperatures, carbon fibers undergo fiber degradation, leading to the need for low-temperature hydrothermal processes. This work will develop and characterize a nanoscale ZnO and MnO2 interface modification for use on carbon fibers. These nanomodifications will be developed with low-temperature processes, minimizing the fiber degradation that the fibers undergo. Fourier transform infrared …

Model-Based Design Of Compressed Lithium-Metal Pouch Cell Battery Modules For Evtol Applications, Scott J. Stirling

Master's Theses

Batteries with higher specific energy and power are essential for extending the range and performance of electric vertical takeoff and landing aircraft (eVTOLs). Anode-free lithium-metal pouch cells offer strong potential at the cell-level but require high compressive pressures to enhance cycle life and discharge performance. These pressures necessitate heavier structural components, reducing packaging efficiency at the module level.

To evaluate this tradeoff, a full-factorial enumeration model was developed to explore viable module designs within a constrained packaging volume. The model scales subsystem masses, enforces design rules and material limits, and accounts for large (~20%) cell thickness changes during cycling.

Results …

Exploring Metal Additive Manufacturing In Martian Atmospheric Environments, Zane Mebruer

Mechanical Engineering Undergraduate Honors Theses

On-surface manufacturing is key to the success of a planetary colonization, especially that of Mars. However, traditional subtractive manufacturing processes are equipment, energy, and material intensive, meaning novel additive manufacturing (AM) processes must be pursued for this end. Selective laser melting, one of the most effective and versatile AM methods, would be incredibly beneficial to a Martian mission but requires an artificial argon atmosphere to create effective parts. The purpose of this study was to examine if carbon dioxide, the gas that makes up over 95% of Mars’ surface atmosphere, would be a sufficient substitute for argon in SLM fabrication. …

A Comparison Of Beamforming Characteristics In Isotropic And Composite Plate Structures For Use In Structural Health Monitoring, Sarah Ketchersid

Doctoral Dissertations and Master's Theses

Structural health monitoring in plate-like simple structures using phased array beamsteering of guided Lamb waves is useful in damage detection and evaluation efforts. Lamb waves can be effectively used for beamsteering using a linear array. The experimentation primarily focuses on beamsteering in the aluminum panel, which involves developing a simulation based on extracted data to visualize the dispersion of waves across the panel. By evaluating parameters such as slowness, velocity, and amplitude direction and variation for a specific metallic plate, the wavefront generated by a single wave source can be represented as a function of propagation angle and distance from …

Kissing Bond Assessment In Adhesive Bonded Carbon Fiber Reinforced Composites Using Dielectric Spectroscopy, Minhazur Rahman

Mechanical and Aerospace Engineering Dissertations - Archive

The widespread use of fiber-reinforced composites in industries such as space, aviation, automobiles, and construction necessitates the formation of robust composite joints between critical structural components. Although adhesive-bonded joints are superior with improved load distribution and reduced weight, they are often overlooked in favor of bolted joints and mechanical fasteners due to the lack of reliable Non-Destructive Evaluation (NDE) techniques for adhesive-bonded composites. The anisotropic nature of the substrate and the intricate interfacial interactions between the adherend and adhesive material present significant challenges for conventional NDE methods. Moreover, weak adhesive bonds can result from uncontrolled manufacturing parameters, such as accidental …

Experimental Investigations And Optimization Of 3d Printed Cellular Structures For Protection Against Traumatic Brain Injury, Aaron R. Jackson

Mechanical and Aerospace Engineering Dissertations - Archive

Traumatic Brain Injury (TBI) disrupts brain function due to head impacts, blast exposures, and ballistic penetrations. It is a significant cause of mental health issues and disability, particularly among military personnel. Historically, combat helmets were designed primarily to protect against fragments. However, recent data highlights the need for helmets that also protect against blast and blunt impacts. Effective TBI prevention requires helmets that address various energy threats while remaining lightweight. A critical metric in this effort is head acceleration, which is closely linked to injury across different scales of brain damage.

Four lattice structures were 3D printed using Digital ABS …

Machine Learning-Assisted Multiscale Simulation And Design Optimization Of Composite Jackets Under Low-Velocity Impacts, Masoud Mohammadi

Graduate Theses, Dissertations, and Problem Reports (ETD)

This research presents the development of a data-driven machine learning-assisted approach to simulate and optimize the design of composite materials subjected to low-velocity impacts. It focuses on a specific type of hybrid composite comprised of fiberglass and Kevlar fabrics stitched with Kevlar threads. The study begins by creating a multiscale finite element simulation for the composite under a low-velocity impact, which operates across three scales: microscale, mesoscale, and macroscale. This simulation accepts various inputs, such as different layer configurations and orientations, and provides impact outputs including maximum load and energy absorption capacity and displacement at failure.

Python and MATLAB scripts …

Cfrp Delamination Density Propagation Analysis By Magnetostriction Theory, Brandon Eugene Williams

All Dissertations

While Carbon Fiber Reinforced Polymers (CFRPs) have exceptional mechanical properties concerning their overall weight, their failure profile in demanding high-stress environments raises reliability concerns in structural applications. Two crucial limiting factors in CFRP reliability are low-strain material degradation and low fracture toughness. Due to CFRP’s low strain degradation characteristics, a wide variety of interlaminar damage can be sustained without any appreciable change to the physical structure itself. This damage suffered by the energy transfer from high- stress levels appears in the form of microporosity, crazes, microcracks, and delamination in the matrix material before any severe laminate damage is observed. This …

Study Of A Carbon Fiber Reinforced Polymer Composite Using A Biobased Polyurethane As A Thermosetting Resin, Teddy Mageto

Electronic Theses & Dissertations

Carbon Fiber Reinforced Polymer composites (CFRP) have garnered increasing interest in recent years especially in the aerospace and automobile industries where they are gradually replacing metals as structural materials. This is owing to their light weight, high strength, high modulus, and excellent strength-to-weight ratio. Polymers are typically used as thermosetting resins in these composites. However, the synthesis of polymers currently is conducted via petrochemical processes which leads to adverse effects on the environment. To this end, in this work a biobased Polyurethane (PU) was used as a thermosetting resin in a CFRP. The biobased PU was synthesized by the reaction …

Application Of Multi-Scale Computational Techniques To Complex Materials Systems, Mujan N. Seif

Theses and Dissertations--Chemical and Materials Engineering

The applications of computational materials science are ever-increasing, connecting fields far beyond traditional subfields in materials science. This dissertation demonstrates the broad scope of multi-scale computational techniques by investigating multiple unrelated complex material systems, namely scandate thermionic cathodes and the metallic foam component of micrometeoroid and orbital debris (MMOD) shielding. Sc-containing "scandate" cathodes have been widely reported to exhibit superior properties compared to previous thermionic cathodes; however, knowledge of their precise operating mechanism remains elusive. Here, quantum mechanical calculations were utilized to map the phase space of stable, highly-faceted and chemically-complex W nanoparticles, accounting for both finite temperature and chemical …

Carbon Fibers From Bio-Based Precursors Derived From Renewable Sources, Sagar Kanhere

All Dissertations

Carbon fibers have the highest strength and modulus among all known fibers and are used as reinforcements in high-performance composites [1]. Carbon fibers also have a very low density relative to metals. Therefore, carbon fibers possess ultrahigh specific strength and modulus, which make them desirable for high-performance light-weight composites. A vast majority of commercial carbon fibers are produced from PAN precursors that are expensive, which limits the use of PAN-derived carbon fibers to aerospace applications (e.g., airplanes). However, for costsensitive applications, there is a need for low-cost, moderate performance carbon fibers. Lignin is a low-cost by-product of pulping and biorefining …

Microscale Transverse Compression Modeling: A Comparative Study Of The Analytical Mac/Gmc Methods To Experimental Results, Emily Zeitunian

Dissertations, Master's Theses and Master's Reports

Composite materials require a multi-scale approach to fully understand its behavior. At the micro level, material behavior analysis is conducted most often using numerical or analytical approaches. These models, however, require validation from experimental data to ensure material predictions are accurate. This study compares a semi-analytical micromechanical analysis tool, MAC/GMC, to experimental results of in-situ microscale transverse compression testing conducted at AFRL facilities. Effective properties, stress-strain curves, stress and strain fields, and damage predictions are compared with experimental outputs. Both generalized method of cells (GMC) and high-fidelity generalized method of cells (HFGMC) theories implemented within MAC/GMC show results that agree …

Mechanical Interfacial Locking And Multiscale Modeling Of Reinforced Thermoplastic Composites For Structural Applications, Anmol Kothari

All Dissertations

The ever-growing pressure of reducing the adverse impact of transportation systems on environment has pushed industries towards fuel-efficient and sustainable solutions. While several approaches have been used to improve fuel efficiency, the light-weighting of structural components has proven broadly effective. In this regard, reinforced thermoplastic composites (RTPC), owing to their high recyclability, higher impact strength and fast cycle times, have become competitive candidates at an industrial scale. However, to implement RTPC toward large scale structural applications several challenges pertaining to material design and manufacturing effects need to be addressed. To this end, a computational study is carried out to address …

Review: Factors Affecting Composite Laminates Against Lightning Strikes, Aaryan Manoj Nair

Publications and Research

Lightning strike protection (LSP) have recently been a newly developing field particularly with the emergence of graphene thin film integration into carbon fiber composite structures. This technology has a widespread application in airplanes, wind turbines, and other instruments which are susceptible to frequent lightning strikes. Electrical discharge of the instrument in a safe manner is vital for the safety of the passengers (in the case of flights) as well as the integrity of the aircraft structures because of their specific mechanical and structural properties, which are essential for their functioning. The purpose of the study is to fabricate graphene thin …

Characterizing High Entropy Alloys For Hypersonic Applications, Katherine Pettus

Mechanical Engineering Undergraduate Honors Theses

In this paper, the properties of a new and broad class of materials, high entropy alloys (HEAs), were investigated and evaluated for hypersonic applications. The plan was to identify candidate hypersonic HEAs and model the high-temperature strength using new advanced material models that account for asymmetry and anisotropy characterized with available test data. After accessing a local database of HEAs and their material properties in collaboration with Dr. Gorsse et al., it was realized the knowledge of HEAs is currently very broad but lacks depth. While hundreds of HEAs have been created and tested, none so far have both sufficient …

Miniaturized Ultraviolet Imager Phase Iii, Bradley D. Albright, Nicolas A. Armenta, Colin W. Harrop

Mechanical Engineering

This document details the work to date, June 9, 2020, done by the Cal Poly Mechanical Engineering senior project team, Miniaturized Ultraviolet Imager: Phase III (MUVI III), sponsored by the University of California, Berkeley – Space Sciences Laboratory (UCB SSL). MUVI III is the third senior project team of an ongoing design, MUVI: the prototype of a 2U sized CubeSat intended to capture aurora images in the ionosphere. The first team, MUVI I, finished development of the UV imager. The second team, MUVI II, designed the mirror mounting and deployable door mechanisms. The goal of MUVI phase III is to …

Carbon Oxidation At The Atomic Level: A Computational Study On Oxidative Graphene Etching And Pitting Of Graphitic Carbon Surfaces, Simon Schmitt

Theses and Dissertations--Mechanical and Aerospace Engineering

In order to understand the oxidation of solid carbon materials by oxygen-containing gases, carbon oxidation has to be studied on the atomic level where the surface reactions occur. Graphene and graphite are etched by oxygen to form characteristic pits that are scattered across the material surface, and pitting in turn leads to microstructural changes that determine the macroscopic oxidation behavior. While this is a well-documented phenomenon, it is heretofore poorly understood due to the notorious difficulty of experiments and a lack of comprehensive computational studies. The main objective of the present work is the development of a computational framework from …

Multiscale Modeling Of Carbon Fibers/Graphene Nanoplatelets/Epoxy Hybrid Composites For Aerospace Applications, Hashim Al Mahmud

Dissertations, Master's Theses and Master's Reports

Significant research effort has been dedicated for decades to improve the mechanical properties of aerospace polymer-based composite materials. Lightweight epoxy-based composite materials have increasingly replaced the comparatively heavy and expensive metal alloys used in aeronautical and aerospace structural components. In particular, carbon fibers (CF)/graphene nanoplatelets (GNP)/epoxy hybrid composites can be used for this purpose owing to their high specific stiffness and strength. Therefore, this work has been completed to design, predict, and optimize the effective mechanical properties of CF/GNP/epoxy composite materials at different length scales using a multiscale modeling approach. The work-flow of modeling involves a first step of using …

Investigation Of Fundamental Principles Of Rigid Body Impact Mechanics, Khalid Alluhydan

Mechanical Engineering Research Theses and Dissertations

In impact mechanics, the collision between two or more bodies is a common, yet a very challenging problem. Producing analytical solutions that can predict the post-collision motion of the colliding bodies require consistent modeling of the dynamics of the colliding bodies. This dissertation presents a new method for solving the two and multibody impact problems that can be used to predict the post-collision motion of the colliding bodies. Also, we solve the rigid body collision problem of planar kinematic chains with multiple contacts with external surfaces.

In the first part of this dissertation, we study planar collisions of Balls and …

Modifying Casting Parameters To Improve The High Temperature Ductility Of Investment Cast Nickel-Based Superalloy Pwa 1455, Lars Alexander Hedin, Cole Magnum Introligator

Materials Engineering

PCC Structurals, an industry leader in superalloy investment castings, has observed inconsistencies in the stress rupture performance of polycrystalline nickel-based superalloy PWA 1455. PCC has changed their casting parameters to reduce the thermal gradient during cooling but have been unable to correlate these changes with an increase in stress rupture elongation. Metallographic examination of past samples indicated microstructures composed of non- equiaxed dendritic grains with mean diameter of .021 inches along the test axis. A similar study on polycrystalline superalloys has indicated that excessive superheat temperatures above the liquidus can result in large grains identical to those observed, limiting the …

3d Textile Preforms And Composites For Aircraft Strcutures: A Review, Abbasali Saboktakin

International Journal of Aviation, Aeronautics, and Aerospace

Over the last decades, the development of 3D textile composites has been driven the structures developed to overcome disadvantages of 2D laminates such as the needs of reducing fabrication cost, increasing through-thickness mechanical properties, and improving impact damage tolerance. 3D woven, stitched, knitted and braided preforms have been used as composites reinforcement for these types of composites. In this paper, advantages and disadvantages of each of them have been comprehensively discussed. The fabric architects and their specification in particular stitched preforms and their deformation mode for aerospace applications have been reviewed. Exact insight into various types of damage in textile …

High Dynamic Range Optical Devices And Applications., Elijah Robert Jensen

Electronic Theses and Dissertations

Much of what we know about fundamental physical law and the universe derives from observations and measurements using optical methods. The passive use of the electromagnetic spectrum can be the best way of studying physical phenomenon in general with minimal disturbance of the system in the process. While for many applications ambient visible light is sufficient, light outside of the visible range may convey more information. The signals of interest are also often a small fraction of the background, and their changes occur on time scales so quickly that they are visually imperceptible. This thesis reports techniques and technologies developed …

Design Survey Of Laminated Composite I-Beam, Mrinmoy Saha

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

Composite I-beams are popular for high-strength low-weight applications. Learning the macro-mechanics and designing the composite I-beam properly are necessary. In this report, a design overview of the composite I-beam is discussed which is based on classical lamination theory where it includes the homogenization approach, the plane stress assumption and the Kirchhoff hypothesis. Using these assumptions, a method was developed to come up with the effective material properties of a beam. Formulas to calculate maximum deflection and maximum bending stress and shear stress and the stress concentration at the connection of web-flange are discussed which describe ways for designing and manufacturing …

The Effects Of Varying Composition And Build Direction On Direct Metal Deposition Fabricated Inconel 718, Abigail P. Nilan, Jessica M. Fordham

Materials Engineering

Inconel 718 (IN718) is a popular wrought superalloy, and is currently being investigated for additive manufacturing (AM) applications in the aerospace industry. However, overaging and the presence of microcracks have caused a significant reduction in properties. The purpose of this study is to meet or exceed the mechanical properties of wrought IN718 by varying the composition and build direction of the AM alloy. Alternative compositions were selected with Oerlilon Metco’s Rapid Alloy Development (RAD) software, and differ in niobium content, which increases the fraction of the primary strengthening phase (γʺ). Direct metal deposition (DMD) was used to fabricate the samples, …

Manufacturing Process Simulation – On Its Way To Industrial Application, Dennis Otten, Tobias A. Weber, Jan-Christoph Arent

International Journal of Aviation, Aeronautics, and Aerospace

Manufacturing process simulation (MPS) has become more and more important for aviation and the automobile industry. A highly competitive market requires the use of high performance metals and composite materials in combination with reduced manufacturing cost and time as well as a minimization of the time to market for a new product. However, the use of such materials is expensive and requires sophisticated manufacturing processes. An experience based process and tooling design followed by a lengthy trial-and-error optimization is just not contemporary anymore. Instead, a tooling design process aided by simulation is used more often. This paper provides an overview …

A Comparison Study Of Composite Laminated Plates With Holes Under Tension, Joun S. Kim

Master's Theses

A Comparison Study of Composite Laminated Plates with Holes under Tension

A study was conducted to quantify the accuracy of numerical approximations to deem sufficiency in validating structural composite design, thus minimizing, or even eliminating the need for experimental test. Error values for stress and strain were compared between Finite Element Analysis (FEA) and analytical (Classical Laminated Plate Theory), and FEA and experimental tensile test for two composite plate designs under tension: a cross-ply composite plate design of [(0/90)4]s, and a quasi-isotropic layup design of [02/+45/-45/902]s, each with a single, centered hole of 1/8” diameter, and 1/4" diameter (four sets …