Structures and Materials Commons^™

Direct Ink Writing Of Functional Fiber/Granular Composites, Zhuoyuan Yang

Doctoral Dissertations and Master's Theses

Direct ink writing provides a versatile manufacturing route for fabricating functional fiber and granular composites with controlled architecture, tunable interfaces, and customized material distributions. Fiber reinforced composites offer high stiffness, strength, fatigue resistance, and functional anisotropy, while granular composites provide scalable access to particle based structures with high material efficiency and broad resource compatibility. However, the additive manufacturing of these composite systems remains challenging. For fiber based composites, precise control of fiber placement, matrix impregnation, interfacial bonding, and freestanding deposition is difficult to achieve during printing. For granular composites, stable particle flow, controllable packing, binder infiltration, and shape retention are …

Made On Mars: Design And Manufacturing Of Structural Polymer-Regolith Composites, Pailey M. Vitale

Williams Honors College, Honors Research Projects

Human exploration of Mars is constrained by harsh environmental conditions and the prohibitive cost of transporting materials from Earth. Long-term sustainability requires the local production of mechanical and structural components using resources available on Mars, thereby minimizing payload mass. This project investigates polymer–regolith composites derived from atmospheric CO₂ and mineral-rich regolith as a pathway toward in-situ manufacturing. These composites, when compatible with additive manufacturing, could replace imported plastics, enable on-demand fabrication, and support closed-loop recycling systems. The objective is to design and evaluate polymer–regolith composites that maintain mechanical integrity and environmental resistance under Martian conditions, including extreme temperature swings, radiation …

Design New Stage For Vacuum Pin On Disk, Miranda Boyd

Williams Honors College, Honors Research Projects

For my senior design project, I am redesigning the moving stage for the vacuum pin-on-disk test used in the Akron Engineering Tribology Lab. This system is used to evaluate bearings and lubricants for aerospace applications under controlled vacuum conditions. The current stage design limits flexibility when adjusting for different testing parameters, so my goal is to develop a new movable stage that allows for varying weights and loads to be applied accurately and safely. The redesigned stage will improve test efficiency, adaptability, and precision, ensuring the system can accommodate a wider range of experimental conditions and materials while maintaining compatibility …

In-Situ Investigations Of Calcium-Magnesium-Aluminosilicates (Cmas) Infiltration Effects On Thermal Barrier Coatings Under Extreme Environments Replicating Jet Engines, Zachary Stein

Doctoral Dissertations and Master's Theses

Calcium-magnesium-aluminosilicate (CMAS) particulates, such as sand or volcanic ash, are ingested by gas turbine jet engines during operation. When operating within high abundance regions, these particulates negatively interact and degrade the high temperature thermal barrier coatings (TBC) protecting underlying superalloy turbine blades vital to engine operation. These CMAS particulates melt within the engine and infiltrate into the ceramic coatings. In electron-beam physical vapor deposited (EB-PVD) TBCs, the CMAS within the intercolumnar gaps stiffens the coatings and causes thermomechanical induced high stress concentrations, risking crack formation. While molten, the CMAS thermochemically alters and destabilizes the coating, also risking coating failure. Premature, …

In-Situ Defect Detection In Selective Laser Melting Using Convolutional Neural Networks, Ethan Gaigalas

Master's Theses

This thesis develops and trains a convolutional neural network (CNN) to classify defects in metal parts produced by selective laser melting (SLM) using acoustic emission (AE) data. The model successfully identified porosity and standard build layers with high accuracy but consistently struggled to classify lack of fusion (LOF) defects, regardless of input type, normalization, or class count. These results suggest that while AE signals contain distinguishable features for certain defect types, LOF signals may be too subtle or inconsistent for reliable detection. The study addresses the ongoing challenge of in-situ quality monitoring in metal additive manufacturing, where defects like cracks, …

Thermal Characterization Of 3d Printing Materials For Increasing Insulation Potential And Practicality, Jackson H. Minnick

Mechanical Engineering Undergraduate Honors Theses

This study served as an exploration into the possible existence of a correlation between the infill lattice structure of a 3D printed wall section and the thermal performance of that sample as characterized by thermal conductivity measured in units of Watts per meter Kelvin. With the continual increase in the practicality, fidelity, and applicable fields of additive manufacturing, namely FDM 3D printing, research on specific print characteristics and their effects on the material and thermal characteristics of the part in question is steadily becoming more commonplace. Although the thermal conductivity of 3D printed wall sections as a function of infill …

Study Of Nanocomposite Materials Using Molecular Dynamics, Prashik Sunil Gaikwad

Dissertations, Master's Theses and Master's Reports

There is an increase in demand for new lightweight structural materials in the aerospace industry for more efficient and affordable human space travel. Polymer matrix composites (PMCs) with reinforcement material as carbon nanotubes (CNTs) have shown exceptional increase in the mechanical properties. Flattened carbon nanotubes (flCNTs) are a primary component of many carbon nanotube (CNT) yarn and sheet materials, which are promising reinforcements for the next generation of ultra-strong composites for aerospace applications. These flCNT/polymer materials are subjected to extreme pressure and temperature during curing process. Therefore there is a need to investigate the evolution of properties during the curing …

Application Of Multi-Scale Computational Techniques To Complex Materials Systems, Mujan N. Seif

Theses and Dissertations--Chemical and Materials Engineering

The applications of computational materials science are ever-increasing, connecting fields far beyond traditional subfields in materials science. This dissertation demonstrates the broad scope of multi-scale computational techniques by investigating multiple unrelated complex material systems, namely scandate thermionic cathodes and the metallic foam component of micrometeoroid and orbital debris (MMOD) shielding. Sc-containing "scandate" cathodes have been widely reported to exhibit superior properties compared to previous thermionic cathodes; however, knowledge of their precise operating mechanism remains elusive. Here, quantum mechanical calculations were utilized to map the phase space of stable, highly-faceted and chemically-complex W nanoparticles, accounting for both finite temperature and chemical …

Carbon Fibers From Bio-Based Precursors Derived From Renewable Sources, Sagar Kanhere

All Dissertations

Carbon fibers have the highest strength and modulus among all known fibers and are used as reinforcements in high-performance composites [1]. Carbon fibers also have a very low density relative to metals. Therefore, carbon fibers possess ultrahigh specific strength and modulus, which make them desirable for high-performance light-weight composites. A vast majority of commercial carbon fibers are produced from PAN precursors that are expensive, which limits the use of PAN-derived carbon fibers to aerospace applications (e.g., airplanes). However, for costsensitive applications, there is a need for low-cost, moderate performance carbon fibers. Lignin is a low-cost by-product of pulping and biorefining …

Microscale Transverse Compression Modeling: A Comparative Study Of The Analytical Mac/Gmc Methods To Experimental Results, Emily Zeitunian

Dissertations, Master's Theses and Master's Reports

Composite materials require a multi-scale approach to fully understand its behavior. At the micro level, material behavior analysis is conducted most often using numerical or analytical approaches. These models, however, require validation from experimental data to ensure material predictions are accurate. This study compares a semi-analytical micromechanical analysis tool, MAC/GMC, to experimental results of in-situ microscale transverse compression testing conducted at AFRL facilities. Effective properties, stress-strain curves, stress and strain fields, and damage predictions are compared with experimental outputs. Both generalized method of cells (GMC) and high-fidelity generalized method of cells (HFGMC) theories implemented within MAC/GMC show results that agree …

Parametric Analysis Of Particle Spreading With Discrete Element Method, Yuxuan Wu

Doctoral Dissertations and Master's Theses

The spreading of metallic powder on the printing platform is vital in most additive manufacturing methods, including direct laser sintering. Several processing parameters such as particle size, inter-particle friction, blade speed, and blade gap size affect the spreading process and, therefore, the final product quality. The objective of this study is to parametrically analyze the particle flow behavior and the effect of the aforementioned parameters on the spreading process using the discrete element method (DEM). To effectively address the vast parameter space within computational constraints, novel parameter sweep algorithms based on low discrepancy sequence (LDS) are utilized in conjunction with …

Miniaturized Ultraviolet Imager Phase Iii, Bradley D. Albright, Nicolas A. Armenta, Colin W. Harrop

Mechanical Engineering

This document details the work to date, June 9, 2020, done by the Cal Poly Mechanical Engineering senior project team, Miniaturized Ultraviolet Imager: Phase III (MUVI III), sponsored by the University of California, Berkeley – Space Sciences Laboratory (UCB SSL). MUVI III is the third senior project team of an ongoing design, MUVI: the prototype of a 2U sized CubeSat intended to capture aurora images in the ionosphere. The first team, MUVI I, finished development of the UV imager. The second team, MUVI II, designed the mirror mounting and deployable door mechanisms. The goal of MUVI phase III is to …

An Investigation Of High-Speed Consolidation And Repair Of Carbon Fiber - Epoxy Composites Through Ultrasonic Welding, David A. Hoskins

LSU Master's Theses

Adhesive repair of carbon fiber composite structures is commonly done on damaged structures to extend the service life. This method requires careful preparation of the damaged surface with intricate steps to ensure good bonding between the repair patch and the parent structure by means of an adhesive film. As with many forms of composite manufacturing, it is required to perform vacuum bagging, debulking, and a heated cure depending on the resin. All these steps make the repair process costly and time consuming.

In this present work, an alternative method of repair is investigated which explores the experimental feasibility of using …

Manipulating Fiber Orientation For The Reduction Of Warpage In Carbon Fiber Composite Sandwich Panels, Landon Burnley, Gabrielle Correia

Materials Engineering

Safran Cabin (Santa Maria, CA), previously known as Zodiac Aerospace, designs and manufactures interior cabin components for private and commercial aircraft. Carbon fiber face sheets have recently been incorporated in their overhead luggage bin assemblies which utilize a composite sandwich panel design, in order to provide additional stiffness to the previous glass fiber sandwich panels. Since the introduction of carbon fiber in these luggage bin panels, Safran has experienced an increase in warpage during manufacturing. When inspected by quality control, the panels are tested mimicking how they are installed in aircraft. If the panels do not meet specifications, the warped …

Optimal Sintering Temperature Of Ceria-Doped Scandia Stabilized Zirconia For Use In Solid Oxide Fuel Cells, Amanda K. Assuncao

Honors Undergraduate Theses

Carbon emissions are known to cause decay of the Ozone layer in addition to creating pollutant, poisonous air. This has become a growing concern among scientists and engineers across the globe; if this issue is not addressed, it is likely that the Earth will suffer catastrophic consequences. One of the main culprits of these harmful carbon emissions is fuel combustion. Between vehicles, power plants, airplanes, and ships, the world consumes an extraordinary amount of oil and fuel which all contributes to the emissions problem. Therefore, it is crucial to develop alternative energy sources that minimize the impact on the environment. …

Design Of Shape-Conforming Nosecone For Optimal Fluid Flow From Transonic To Supersonic Range, Anna Tombazzi

Williams Honors College, Honors Research Projects

Modern flight vehicles, such as rockets, missiles, and airplanes, experience a force caused by forebody wave drag during the flight. This drag force is induced when the frontal point of each vehicle breaks the pressure wave during flight. Efforts to reduce this wave drag force to improve flight efficiency include modifying the nosecone profile of the flight vehicles to lower the drag force.

This project revolved around creating a design to make the transformation of nosecone shapes from a ¾ Parabolic profile to a ½ Power Series profile possible, mid-flight. Using a novel nosecone assembly, shape memory alloys (SMAs) and …

The Effect Of Biocomposite Material In A Composite Structure Under Compression Loading, Benjamin Andrew Sweeney

Master's Theses

While composite structures exhibit exceptional strength and weight saving possibilities for engineering applications, sometimes their overall cost and/or material performance can limit their usage when compared to conventional structural materials. Meanwhile ‘biocomposites’, composite structures consisting of natural fibers (i.e. bamboo fibers), display higher cost efficiency and unique structural benefits such as ‘sustainability’. This analysis will determine if the integration of these two different types of composites are beneficial to the overall structure. Specifically, the structure will consist of a one internal bamboo veneer biocomposite ply; and two external carbon fiber weave composite plies surrounding the bamboo biocomposite. To acquire results …

Predicting Flexural Strength Of Composite Honeycomb Core Sandwich Panels Using Mechanical Models Of Face Sheet Compressive Strength, Nicholas Bruffey, William Shiu

Materials Engineering

The design process at Zodiac Aerospace requires the ability to accurately predict the strength of a composite honeycomb core sandwich panel to adhere to strict FAA regulations. The most common failure mode in long beam composites is in compression. Following ASTM D7249 for a four-point bend test of a long beam flexural test, a mechanical model has been developed that relates the compressive strength of glass fiber face sheets to the flexural strength of the sandwich panel. Zodiac does not currently have data on the compressive strength of the face sheets, so testing was performed to find this property. Asymmetric …

Shape Memory Behavior Of Single Crystal And Polycrystalline Ni-Rich Nitihf High Temperature Shape Memory Alloys, Sayed M. Saghaian

Theses and Dissertations--Mechanical and Aerospace Engineering

NiTiHf shape memory alloys have been receiving considerable attention for high temperature and high strength applications since they could have transformation temperatures above 100 °C, shape memory effect under high stress (above 500 MPa) and superelasticity at high temperatures. Moreover, their shape memory properties can be tailored by microstructural engineering. However, NiTiHf alloys have some drawbacks such as low ductility and high work hardening in stress induced martensite transformation region. In order to overcome these limitations, studies have been focused on microstructural engineering by aging, alloying and processing.

Shape memory properties and microstructure of four Ni-rich NiTiHf alloys (Ni50.3Ti29.7Hf20, Ni50.7Ti29.3Hf20, …

Simulation Of Bio-Inspired Porous Battery Electrodes, Raju Gupta, R. Edwin Garcia, Rui Tu

The Summer Undergraduate Research Fellowship (SURF) Symposium

Advancement of technology has led to the increase in use of electronic devices. However, longer life of the rechargeable battery used in electronic devices is one of the biggest issue and demand in the world of electronic devices at present. Battery's performance is affected by the orientation, arrangement, shape and size, and porosity of the materials out of which battery electrodes are made. The goal of this project is to develop a set of numerical libraries that allow developing material micro structures that will allow increasing the performance of rechargeable batteries. We focused on the development of an algorithm that …

An Investigation Into The Properties And Fabrication Methods Of Thermoplastic Composites, Ann E. Livingston-Peters

Master's Theses

As applications for thermoplastic composites increase, the understanding of their properties become more important. Fabrication methods for thermoplastic composites continually improve to match designs specifications. These advanced thermoplastics have begun to show an improvement in mechanical properties over those found in thermoset composites commonly used in industry. Polyaryletherketones (PEK) have high service temperatures, good mechanical properties, and improved processing capabilities compared to thermoplastics used in the past making them important to the aerospace industry. The wide range of types of PEK make them suitable for a variety of applications, but selection of specific chemistries, processing parameters, and composite stack-ups determine …

Mode I Fracture Toughness Of Eight-Harness-Satin Carbon Cloth Weaves For Co-Cured And Post-Bonded Laminates, Josh E. Smith

Master's Theses

Mode I interlaminar fracture of 3k 8-Harness-Satin Carbon cloth, with identical fill and weft yarns, pre-impregnated with Newport 307 resin was investigated through the DCB test (ASTM D5528). Crack propagations along both the fill and weft yarns were considered for both post-bonded (co-bonded) and co-cured laminates. A patent-pending delamination insertion method was compared to the standard Teflon film option to assess its applicability to mode I fracture testing. The Modified Beam Theory, Compliance Calibration method, and Modified Compliance Calibration method were used for comparative purposes for these investigations and to evaluate the validity of the proposed Equivalent Stiffness (EQS) method. …