Structures and Materials Commons^™

Smart Process Planning For Automated Fiber Placement, Matthew J. Godbold

All Dissertations

Automated Fiber Placement (AFP) is a preeminent manufacturing technology for producing high-performance composite structures, offering precise material placement, reduced waste, and the potential for highly optimized lightweight designs. While AFP has been widely adopted in aerospace applications, its broader use across industries such as automotive, wind energy, maritime, and sporting goods remains limited. A key barrier to wider adoption is the traditional separation of design, manufacturing, and inspection processes, which drives up cost and results in inefficiencies, sub-optimal designs, and limited feedback between lifecycle stages. In current practice, manufacturing is treated as an isolated process, disconnected from early-stage design decisions …

Direct Ink Writing Of Functional Fiber/Granular Composites, Zhuoyuan Yang

Doctoral Dissertations and Master's Theses

Direct ink writing provides a versatile manufacturing route for fabricating functional fiber and granular composites with controlled architecture, tunable interfaces, and customized material distributions. Fiber reinforced composites offer high stiffness, strength, fatigue resistance, and functional anisotropy, while granular composites provide scalable access to particle based structures with high material efficiency and broad resource compatibility. However, the additive manufacturing of these composite systems remains challenging. For fiber based composites, precise control of fiber placement, matrix impregnation, interfacial bonding, and freestanding deposition is difficult to achieve during printing. For granular composites, stable particle flow, controllable packing, binder infiltration, and shape retention are …

Mars Rover Wheels And Drive, Presley S. Sacavitch, Ryan W. Trevena, Dylan A. Mack, Daniel Hudak

Mechanical Engineering

Cal Poly’s Poly1Rover team, advised by Professor Rich Murray, aims to deploy four student-designed mini-Mars rovers, each equipped with a sample-tube retrieval claw, before 2030. However, the wheels of Poly1Rover’s current 6th generation rover are not ready for deployment to Mars, as they do not utilize space-grade materials, are not optimized for manufacturability, and lack sufficient spoke compliance to absorb landing and high-impact loads. This project will be developed by a team of Mechanical Engineering students at California Polytechnic State University, San Luis Obispo (Cal Poly): Daniel Hudak, Dylan Mack, Presley Sacavitch, and Ryan Trevena. Next Intent is providing funding …

Improving The Reliability And Performance Of A Supersonic Indraft Tube Wind Tunnel, Christian J. Kaml

Master's Theses

Access to supersonic testing is increasing in demand, and wind tunnels remain one of the safest and most cost-effective methods for gathering high-speed flow data. Despite being more economical than alternative options, supersonic wind tunnel facilities often require substantial investment to construct, operate, and maintain.

The novel indraft tube tunnel architecture was conceived as a high-speed flow testbed that incorporates features of both Ludwieg tubes and indraft wind tunnels to maintain costs low enough to be accessible even to small universities. This design was first developed and tested in 2018 at California Polytechnic State University, featuring a cost per test …

Detecting And Repairing Conflicting Constraints In Co-Trained Physics-Informed Neural Networks For Composite Curing Processes, Cooper J. Evans

Dissertations, Master's Theses and Master's Reports

Composite materials have become a critical component of modern manufacturing, especially in the automotive and aerospace industries. The curing process for these composites has been modeled using a variety of partial differential equations representing the heat transfer and composite curing kinetics. Optimizing the applied temperature profile is critical for maximizing the efficiency and capacity of composite part manufacturers. Constraints must be placed on the inputs and outputs of the model, including but not limited to, the applied temperature profile, part temperature, and final degree of cure. Conflicting sets of constraints are easy to unknowingly impose due to the highly coupled …

Optimization Of Post-Processing Methods For Additively Manufactured Metals, Julia R. Carano

Williams Honors College, Honors Research Projects

Ultrasonic Nanocrystal Surface Modification (UNSM) is a process used to change the surface hardness of flat-faced materials. It is a machining process using a high-powered laser and a blunt-tipped tool at high speeds which aims to improve the uniformity of the surface on most metals. By heating and pressing the surface of the workpiece, the grains of the material become less rounded and more cohesive on a microscopic level. This, ideally, results in a workpiece with improved material properties. The changes were previously observed through hardness testing.

Fused Filament Fabrication Additive Manufacturing Of 17-4 Ph Stainless Steel: Process–Structure–Property Relationships In Magnetic Materials, Maanav Patel

Theses and Dissertations

Additive manufacturing (AM) enables the fabrication of complex metallic components through layer-by-layer processing directly from digital models. Among AM techniques, material extrusion–based processes such as fused filament fabrication (FFF) provide an accessible method for producing metal parts using filament feedstocks composed of metal powders and polymer binders. When applied to precipitation-hardening stainless steels such as 17-4 PH, the processing route and heat treatments can influence the resulting microstructure and functional properties. This work investigates the magnetic behavior of 17-4 PH stainless steel fabricated using FFF and evaluates how heat treatment conditions influence measured magnetic properties. Samples were produced and analyzed …

Improving Fatigue Strength And Life Of Single Crystal Cmsx-4, Jochen Peter Fuhr, Lloyd Hackel, Nicolau I. Morar, Noah Holtham, Keivan Davami, Montu Sharma, Rajkumar Roy

15th International Conference on Shot Peening

The deep penetration of laser peening (LP) and retention of residual stress at high temperature by LP is significant in improving fatigue life and strength of superalloys exposed to high temperature and corrosion. Single crystal CMSX-4, was evaluated for stress relaxation and both fatigue life and fatigue strength of material that was LP-treated compared to non-LP and shot-peened (SP) specimens. LP was done with multiple layers using a 20 J/pulse laser where the laser high energy enabled using a 5 mm spot size on the metal surface. Stress measurements by the slitting technique showed the plastic penetration depth exceeded SP …

In-Situ Defect Detection In Selective Laser Melting Using Convolutional Neural Networks, Ethan Gaigalas

Master's Theses

This thesis develops and trains a convolutional neural network (CNN) to classify defects in metal parts produced by selective laser melting (SLM) using acoustic emission (AE) data. The model successfully identified porosity and standard build layers with high accuracy but consistently struggled to classify lack of fusion (LOF) defects, regardless of input type, normalization, or class count. These results suggest that while AE signals contain distinguishable features for certain defect types, LOF signals may be too subtle or inconsistent for reliable detection. The study addresses the ongoing challenge of in-situ quality monitoring in metal additive manufacturing, where defects like cracks, …

Exploring Metal Additive Manufacturing In Martian Atmospheric Environments, Zane Mebruer

Mechanical Engineering Undergraduate Honors Theses

On-surface manufacturing is key to the success of a planetary colonization, especially that of Mars. However, traditional subtractive manufacturing processes are equipment, energy, and material intensive, meaning novel additive manufacturing (AM) processes must be pursued for this end. Selective laser melting, one of the most effective and versatile AM methods, would be incredibly beneficial to a Martian mission but requires an artificial argon atmosphere to create effective parts. The purpose of this study was to examine if carbon dioxide, the gas that makes up over 95% of Mars’ surface atmosphere, would be a sufficient substitute for argon in SLM fabrication. …

Experimental And Theoretical Fracture Analysis Of Additively Manufactured Orthotropic V-Notches, Venkata Siva Sainath Bavapuram

Theses and Dissertations

This study presents a comprehensive investigation into the fracture behavior of additively manufactured orthotropic V-notched components made of Acrylonitrile Butadiene Styrene (ABS) material. The research integrates both theoretical and finite element approaches to evaluate stress intensity factors (SIFs) in Modes-I and II, which are fundamental in characterizing stress field distributions around notches under applied loading conditions. Unlike isotropic materials, where stress fields depend only on geometry of the component, the anisotropic nature of 3D-printed ABS introduces a dependency on material properties that necessitate different approaches to include anisotropy of the material.

Tensile specimens are 3D-printed with specific material orientations to …

Thermal Characterization Of 3d Printing Materials For Increasing Insulation Potential And Practicality, Jackson H. Minnick

Mechanical Engineering Undergraduate Honors Theses

This study served as an exploration into the possible existence of a correlation between the infill lattice structure of a 3D printed wall section and the thermal performance of that sample as characterized by thermal conductivity measured in units of Watts per meter Kelvin. With the continual increase in the practicality, fidelity, and applicable fields of additive manufacturing, namely FDM 3D printing, research on specific print characteristics and their effects on the material and thermal characteristics of the part in question is steadily becoming more commonplace. Although the thermal conductivity of 3D printed wall sections as a function of infill …

40 - Design, Fabrication, And Installation Of Morphing Control Surfaces For Small-Scale Uas, Kyle Purser

Undergraduate Research Symposium

Morphing control surface technology, inspired by organic structures and compliant mechanisms, offers significant potential for enhancing the aerodynamic efficiency and performance of unmanned aerial systems (UAS). Despite these benefits, its adoption has been hindered by complexities in design, manufacturing, and installation, particularly when compared to traditional flap systems. This research explores the design, fabrication, and integration of morphing control surfaces for small-scale UAS using additive manufacturing techniques. To reduce costs and streamline the design process, fused deposition modeling (FDM) additive manufacturing was employed for component fabrication. An off-the-shelf Horizon Sport Cub S2 served as the testing platform, modified with a …

Development And Processing Of Shape Memory Polymer Composites (Smpcs) For Application In Structural Robotics And Robotic Sensors., Kavish Sudan

Electronic Theses and Dissertations

Shape Memory Polymers (SMPs) have attracted significant attention since their introduction in the 1980s due to their remarkable ability to regain their original shape from a temporarily deformed state when exposed to an external stimulus, typically heat. This shape memory effect, driven by thermal transitions such as the glass transition temperature (T_g) or melting temperature (T_m), has made SMPs highly attractive for applications in soft robotics, aerospace, and biomedical devices. However, SMPs face challenges such as limited mechanical strength, thermal stability, and electrical conductivity, which hinder their broader adoption in advanced applications. To address these challenges, …

Kissing Bond Assessment In Adhesive Bonded Carbon Fiber Reinforced Composites Using Dielectric Spectroscopy, Minhazur Rahman

Mechanical and Aerospace Engineering Dissertations - Archive

The widespread use of fiber-reinforced composites in industries such as space, aviation, automobiles, and construction necessitates the formation of robust composite joints between critical structural components. Although adhesive-bonded joints are superior with improved load distribution and reduced weight, they are often overlooked in favor of bolted joints and mechanical fasteners due to the lack of reliable Non-Destructive Evaluation (NDE) techniques for adhesive-bonded composites. The anisotropic nature of the substrate and the intricate interfacial interactions between the adherend and adhesive material present significant challenges for conventional NDE methods. Moreover, weak adhesive bonds can result from uncontrolled manufacturing parameters, such as accidental …

Short Strand Carbon Fiber Reinforced Polylactic Acid Filament For Additive Manufacturing, Dale Chenoweth, Lukas Seggi, Luke Phillips

Williams Honors College, Honors Research Projects

In this design project, the additive manufacturing filament of short strand carbon fiber (SSCF) reinforced polylactic acid (PLA) composite was developed. The micro-size, precision cut SSCFs were mixed with the PLA pellets through a melting homogenization process. Through this process the composite material block is cut and divided into pieces for ease of pelletizing. The material block pieces are then pelletized to be fed through the single screw extruder to develop the SSCF-PLA composite filament. The SSCF-PLA filaments were manufactured with a varying amount of SSCF ranging from 0.5% to 10% of the material block's weight. Development of a 1% …

Kwad - Ksu All Weather Autonomous Drone, Nick Farinacci, Sebastian Gomez, Stewart Baker, Ed Sheridan

Symposium of Student Scholars

"KWAD" or "KSU all-Weather Autonomous Drone" project was sponsored by Ultool, LLC to the KSU Research and Service Foundation to create a lightweight drone capable of capturing HD video during all-weather operations. The conditions of all-weather operation include rainfall of one inch per hour and wind speeds of up to twenty miles per hour. In addition, a global minimum structural safety factor of two is required to ensure the system's integrity in extreme weather conditions. Potential mission profiles include autonomous aerial delivery, topological mapping in high moisture areas, security surveillance, search and rescue operations, emergency transportation of medical supplies, and …

Additive Manufacturing And Characterization Of Auxetic Structures, Jayesh P. Moore, Stephanie R. Ruzicka

College of Engineering Summer Undergraduate Research Program

An auxetic structure is an arrangement of unit cells that under a uniaxial load experiences expansion in both the longitudinal and transverse directions, resulting in a negative Poisson’s ratio (NPR). Research in auxetics has led to new insights into how non-linear mechanical reactions can be applied to various engineering fields. This project utilized stereolithography (SLA) 3D printing to manufacture auxetic test specimens to analyze of geometry-driven NPRs. With the distinctive mechanical properties of auxetic structures and vast applications, the future of product development of these geometries seems promising.

Empowering Student Success: Unlocking The Potential Of Project-Based Steel Design Education, Aly Mousaad Aly

Faculty Publications

In the pursuit of student success, it is essential to acknowledge that a singular teaching style does not universally cater to all students. The educator's crucial role lies in creating an optimal learning environment that fosters students' endeavors to excel. This endeavor transcends mere classroom success or employment prospects, encompassing a broader impact on societal well-being. An experiential learning approach, where students actively engage in practical tasks, emerges as the most effective mode of instruction. Integrating project-based learning activities into the curriculum holds immense potential for enhancing student learning. Additionally, the utilization of analysis software tools like FTool and STAAD …

Effects Of Tempering Temperature On Gas Turbine Fan Cases, Seth Utter

Honors Scholar Theses

The project aimed to investigate the effects of tempering temperature on metals used for gas turbine engine fan cases as a major relevant concern is containing blades in during blade-out events. There are three ways to accomplish this: using a thicker metal, incorporating different materials into the case, or heat treating the metal. This project focused on the third solution: reviewing the impact toughness and hardness of fractured samples and their equivalent ductile-to-brittle transition shear faces. Given its availability, 1045 steel, as opposed to aerospace grade metals, was used for in-house testing. The data obtained from these experiments were then …

Jcati Carbon Fiber Recycler: Crusher System, Devin Riley

All Undergraduate Projects

With a substantial rise in Carbon Fiber use across all industries, the need for a way to recycle the waste has grown as well. A group of Mechanical Engineering Technology students at Central Washington University funded by the Joint Center for Aerospace Technology (JCATI) have created a machine to recycle waste wing trimmings from the Boeing company’s airplanes. This machine consists of 5 different sub-assemblies being the oven, crusher, gear train, conveyor, and shredder. The purpose of this project was to decrease the deflection in the crusher caused by bulging in the housing and movement of the bearings. To decrease …

Exploring Additive Manufacturing In A Space Environment - A Capstone Design Project Experience, Zain Zafar Khan, Zachary Alan Sobelman, Sharanabasaweshwara Asundi

Mechanical & Aerospace Engineering Faculty Publications

The employment of additive manufacturing in the non-standard environments like space, ships, or submarines has the potential to be an advanced utility not only in the pre-flight production of aerospace components and structures, but also for the onboard manufacturing of components and tools necessary for future space missions. For example, the ability to produce tools and structural components on the International Space Station can provide the space community the opportunity to make repairs and upgrades to the space station without wasting time and resources transporting such materials through additional missions. Additive manufacturing would allow for space missions to use on …

Effects Of A Nitrogen And Hydrogen Build Atmosphere On The Properties Of Additively Manufactured Tungsten, Dana C. Madsen

Theses and Dissertations

Additively manufactured tungsten was printed in pure nitrogen, nitrogen-2.5% hydrogen, and nitrogen-5% hydrogen atmospheres as part of a 2^3 full factorial designed experiment and subjected to room temperature and high-temperature three-point-bend testing, chemical analysis, hardness testing, and microstructural imaging techniques. The pure nitrogen specimens exhibited the highest strength and ductility at both high temperature and room temperature. Chemical analysis showed a 2-8x reduction in compositional oxygen relative to unprocessed powder. Hardness values for all samples was between 306.8 and 361.5 HV1. It is proposed that adding hydrogen into the build atmosphere reduced the available energy density for tungsten melting by …

Investigation Of Additively Manufactured Molybdenum-Tungsten-Rhenium Alloys, Randolph T. Abaya

Theses and Dissertations

The process of creating metal components through additive manufacturing is changing the way different industries can avoid the shortcomings of traditional metal production. Metals such as tungsten, molybdenum, and rhenium have many advantages for different applications, especially when alloyed together. In this study, an additively manufactured alloy containing 70% molybdenum, 25% tungsten, and 5% rhenium (70Mo-25W-5Re) is tested for its strength, ductility, hardness, and porosity. The 70Mo-25W-5Re alloy is printed through Laser Powder Bed Fusion (LPBF) under different conditions such as printing speed and printing atmosphere. Additionally, the effects of post printing heat treatment are conducted to understand the advantages …

Carbon Fiber Recycling: Delamination System, Aaron Eastman

All Undergraduate Projects

The production of composite wings at Boeing causes carbon fiber waste and CWU Mechanical Engineering Technology students have been tasked in designing a carbon fiber recycling system. This project was brought forth and funded by the Joint Center for Aerospace Technology Innovation (JCATI). There are three subsystems that make up the carbon fiber recycling system, the delamination system, shredding system, and the oven. The purpose of this project was to increase the efficiency and effectiveness of the delamination system of the carbon fiber recycling system. The old system reached approximately 30-40 percent delamination with one pass through the system, and …

Jcati Carbon Fiber Shredder 2022, Parker Sudderth

All Undergraduate Projects

This project is a potential solution to keep the carbon fiber waste from airplane manufacturing to a minimum, sponsored by the Joint Center for Aerospace Technology Innovation (JCATI). The design and assembly will be scalable for future industry application. The overall design of the whole carbon fiber recycler consists of a crusher, shredder, and oven. This report is on the caron fiber shredder module. The shredder is tasked with being able to shred the delaminated carbon fiber scrap that directly comes from the crusher. The operation must produce shreds in the proper size to be gathered and delivered to the …

Jcati Carbon Fiber Recycler: Oven Enclosure, Margarita Romero

All Undergraduate Projects

Central Washington University partners with Boeing and is funded by the Joint Center of Aerospace Technology Innovation (JCATI) to develop a mechanism that takes carbon fiber wing trimmings from Boeing that are resin coated and recycles carbon fiber. This is done by crushing the wing trimmings and then putting it into a 500°C oven to melt off the resin. This project focuses on the enclosure for the oven and making sure precautions are met such as having the outside surface be less than 45c through heat transfer analysis, argon fills enclosure in 13 minutes through fluid dynamics analysis, and 99% …

Accelerated Controller Tuning For Wind Turbines Under Multiple Hazards, Aly Mousaad Aly, Milad Rezaee

Faculty Publications

During their lifecycle, wind turbines can be subjected to multiple hazard loads, such as high-intensity wind, earthquake, wave, and mechanical unbalance. Excessive vibrations, due to these loads, can have detrimental effects on energy production, structural lifecycle, and the initial cost of wind turbines. Vibration control by various means, such as passive, active, and semi-active control systems provide crucial solutions to these issues. We developed a novel control theory that enables semi-active controller tuning under the complex structural behavior and inherent system nonlinearity. The proposed theory enables the evaluation of semi-active controllers’ performance of multi-degrees-of-freedom systems, without the need for time-consuming …

Mechanical Properties Of Nanomodified Hybrid Gfrp Composite Materials, Micah Rop Kimutai

College of Graduate Studies: Theses & Dissertations

The mechanical behavior of the nanomodified hybrid epoxy matrix was investigated in glass fiber reinforced plastics (GFRP). In this study, five nanocomposites enriched with as received halloysite, nanomer I.28E, HNT-APTES, and the hybrid combinations of the two HNTs with the nanomer I.28E were successfully fabricated. To evaluate the effects and morphological characteristics of the individual fillers and the hybrid configurations on the epoxy resin matrix, TGA, DSC, and DMA were analyzed. To understand the effect of the five configurations on the neat GFRP laminate, mode I interlaminar fracture toughness, tensile, and vibration properties were investigated. Electron microscopy testing techniques were …

Miniaturized Ultraviolet Imager Phase Iii, Bradley D. Albright, Nicolas A. Armenta, Colin W. Harrop

Mechanical Engineering

This document details the work to date, June 9, 2020, done by the Cal Poly Mechanical Engineering senior project team, Miniaturized Ultraviolet Imager: Phase III (MUVI III), sponsored by the University of California, Berkeley – Space Sciences Laboratory (UCB SSL). MUVI III is the third senior project team of an ongoing design, MUVI: the prototype of a 2U sized CubeSat intended to capture aurora images in the ionosphere. The first team, MUVI I, finished development of the UV imager. The second team, MUVI II, designed the mirror mounting and deployable door mechanisms. The goal of MUVI phase III is to …