Structures and Materials Commons^™

Adaptive Control Of An Aeroelastic System For Active Flutter Suppression And Disturbance Rejection, Patrick Sterling Downs

Doctoral Dissertations and Master's Theses

The future of aircraft design strives for lighter weight, more aerodynamically efficient structures. These improvements may come with the drawback of increased structural flexibility and elevated aeroelastic effects, often resulting in a lower flutter speed. This motivates the implementation of advanced control methods to control aeroelastic systems over a range of flight conditions, suppress and delay the onset of flutter, and compensate for disturbances, actuator dynamics, and unmodeled nonlinear dynamics.

This dissertation first develops a novel method for constructing time-domain simulation models of two and three-dimensional aeroelastic systems, resulting in models that are suitable for the implementation of state-space control …

Initial Stage Of Fluid-Structure Interaction Of A Celestial Icosahedron Shaped Vacuum Lighter Than Air Vehicle, Dustin P. Graves

Theses and Dissertations

The analysis of a celestial icosahedron geometry is considered as a potential design for a Vacuum Lighter than Air Vehicle (VLTAV). The goal of the analysis is ultimately to understand the initial fluid-structure interaction of the VLTAV and the surrounding airflow. Up to this point, previous research analyzed the celestial icosahedron VLTAV in relation to withstanding a symmetric sea-level pressure applied to the membrane of the structure. This scenario simulates an internal vacuum being applied in the worst-case atmospheric environmental condition. The next step in analysis is to determine the aerodynamic effects of the geometry. The experimental setup for obtaining …

Metamodels Of Residual Stress Buildup For Machining Process Modeling, Stuart B. Mccrorie, Michael Sangid

The Summer Undergraduate Research Fellowship (SURF) Symposium

In the process of machining materials, stresses, called residual stresses, accumulate in the workpiece being machined that remain after the process is completed. These residual stresses can affect the properties of the material or cause part distortion, and it is important that they be calculated to prevent complications from arising due to the residual stresses. However, these calculations can be incredibly computationally intensive, and thus other methods are needed to predict the residual stresses in materials for quick decision-making during machining. By using metamodels - a method of representing data where few data points exist - we can achieve an …

Simulation Of Bio-Inspired Porous Battery Electrodes, Raju Gupta, R. Edwin Garcia, Rui Tu

The Summer Undergraduate Research Fellowship (SURF) Symposium

Advancement of technology has led to the increase in use of electronic devices. However, longer life of the rechargeable battery used in electronic devices is one of the biggest issue and demand in the world of electronic devices at present. Battery's performance is affected by the orientation, arrangement, shape and size, and porosity of the materials out of which battery electrodes are made. The goal of this project is to develop a set of numerical libraries that allow developing material micro structures that will allow increasing the performance of rechargeable batteries. We focused on the development of an algorithm that …

Development Of A Pyrotechnic Shock Simulation Apparatus For Spacecraft Applications, Joseph Binder, Matthew Mccarty, Chris Rasmussen

Aerospace Engineering

This report details the research, design, construction, and testing of a pyrotechnic shock simulation apparatus for spacecraft applications. The apparatus was developed to be used in the Space Environments Lab at California Polytechnic State University. It will be used for testing spacecraft components with dimensions up to 24”x12”x12” as well as CubeSats. Additionally, it may be used as an instructional or demonstrational tool in the Aerospace Department’s space environments course. The apparatus functions by way of mechanical impact of an approximately 20 lb stainless steel swinging hammer. Tests were performed to verify the simulator’s functionality. Suggestions for improvement and further …

Thermal Vacuum Integration For Cal Poly's Space Environments Laboratory, Chelsea Barackman, Steven Jackowski

Aerospace Engineering

The purpose of the senior project is to construct a thermal vacuum by utilizing a preexisting vacuum chamber in the Space Environments Lab, and a donated Advanced Thermal Sciences (ATS) chiller. While a thermal vacuum is already available on campus, building one for the Space Environments Lab would grant undergraduates access to the equipment, allowing a much better understanding of testing methods and procedures in use by the aerospace industry. This paper explains the design and analysis of the thermal vacuum (T-VAC) project as well as the operation and procedures required for the ATS chiller and fill/drain tank. The thermal …

Impact Simulation And Analysis Of Sandwich Structures, Daewon Kim

Master's Theses - Daytona Beach

Impact damage on aircraft and spacecraft can be a severe problem that may cause catastrophic results. Several aerospace structures have been used to resist or absorb energy in the occasion of impact. Among these, a sandwich structure has advantages with high stiffness, strength to weight ratio, and its relatively cheap cost. However, finding the impact structural response of a sandwich structure, by performing experiments, has disadvantages. First, impact is a complex problem with a multi-parameter nature and many factors should be considered. Secondly, it is a destructive test and the test subject may be damaged during the test. On the …