Engineering Commons^™

Laboratory And Full Boom-Based Investigation Of Nozzle Setup Error Effects On Flow, Pressure, And Spray Pattern Distribution, S. H. Forney, J. D. Luck, Michael F. Kocher, Santosh K. Pitla

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Pesticide application is an integral part of crop production, and ground-based agricultural boom sprayers are used extensively to apply pesticides to the crop canopy or soil surface across millions of acres in the United States. Efficient application is necessary to minimize costs and limit adverse environmental impacts. The goals of this study were to provide quantified measurements on the effects of nozzle setup errors on spray pattern uniformity and evaluate how laboratory patternator-based simulations would compare to measurements on a full spray boom. More specific objectives were to determine the effects of factors such as nozzle lateral angle, nozzle spacing, …

Sugar Versus Lipid For Sustainable Biofuels, Yaşar Demirel

Yaşar Demirel Publications

Introduction

First‐generation biofuels, namely, ethanol and biodiesel, have led to far reaching impact on the peoples’ life world‐wide.[1] However, they inter-fere with the food supply chain and may not be sustainable although some of the biomass are converted to biofuels after those biomasses have met the human needs. Still, the first‐generation–based biofuels have proved that sugar and lipid platforms can be an answer to energy security and global warming concerns without the need for new infrastructure for feedstock delivery as well as for biomass‐to‐biofuel conversion tech-nologies. At the same time, we are discovering and assessing the long‐term environmental im-plications on …

In-Situ Terahertz Optical Hall Effect Measurements Of Ambient Effects On Free Charge Carrier Properties Of Epitaxial Graphene, Sean Knight, Tino Hofmann, Chamseddine Bouhafs, Nerijus Armakavicius, Philipp Kühne, Vallery Stanishev, Ivan G. Ivanov, Rositsa Yakimova, Shawn Wimer, Mathias Schubert, Vanya Darakchieva

Department of Electrical and Computer Engineering: Faculty Publications

Unraveling the doping-related charge carrier scattering mechanisms in two-dimensional materials such as graphene is vital for limiting parasitic electrical conductivity losses in future electronic applications. While electric field doping is well understood, assessment of mobility and density as a function of chemical doping remained a challenge thus far. In this work, we investigate the effects of cyclically exposing epitaxial graphene to controlled inert gases and ambient humidity conditions, while measuring the Lorentz force-induced birefringence in graphene at Terahertz frequencies in magnetic fields. This technique, previously identified as the optical analogue of the electrical Hall effect, permits here measurement of charge …

Rainbow Peacock Spiders Inspire Miniature Superiridescent Optics, Bor-Kai Hsiung, Radwanul Hasan Siddique, Doekele G. Stavenga, Jürgen C. Otto, Michael C. Allen, Ying Liu, Yongfeng Lu, Dimitri D. Deheyn, Matthew D. Shawkey, Todd A. Blackledge

Department of Electrical and Computer Engineering: Faculty Publications

Colour produced by wavelength-dependent light scattering is a key component of visual communication in nature and acts particularly strongly in visual signalling by structurallycoloured animals during courtship. Two miniature peacock spiders (Maratus robinsoni and M. chrysomelas) court females using tiny structured scales (~ 40 × 10 μm²) that reflect the full visual spectrum. Using TEM and optical modelling, we show that the spiders’ scales have 2D nanogratings on microscale 3D convex surfaces with at least twice the resolving power of a conventional 2D diffraction grating of the same period. Whereas the long optical path lengths required …

Controllable Plasmonic Nanostructures Induced By Dual-Wavelength Femtosecond Laser Irradiation, Weina Han, Lan Jiang, Xiaowei Li, Qingsong Wang, Shaojun Wang, Jie Hu, Yongfeng Lu

Department of Electrical and Computer Engineering: Faculty Publications

We demonstrated an abnormal double-peak (annular shaped) energy deposition through dualwavelength synthesis of the fundamental frequency (ω) and the second-harmonic frequency (2ω) of a femtosecond (fs) Ti:sapphire laser. The annular shaped distribution of the dual-wavelength fs laser was confirmed through real beam shape detection. This uniquely simple and flexible technique enables the formation of functional plasmonic nanostructures. We applied this double-peak fs-laser-induced dewetting effect to the controlled fabrication and precise deposition of Au nanostructures, by using a simple, lithography-free, and single-step process. In this process, the double-peak energy-shaped fs laser pulse induces surface patterning of a thin film followed by …

Preparation Of Monolayer Mos2 Quantum Dots Using Temporally Shaped Femtosecond Laser Ablation Of Bulk Mos2 Targets In Water, Bo Li, Lan Jiang, Xin Li, Peng Ran, Pei Zuo, Andong Wang, Liangti Qu, Yang Zhao, Zhihua Cheng, Yongfeng Lu

Department of Electrical and Computer Engineering: Faculty Publications

Zero-dimensional MoS₂ quantum dots (QDs) possess distinct physical and chemical properties, which have garnered them considerable attention and facilitates their use in a broad range of applications. In this study, we prepared monolayer MoS₂ QDs using temporally shaped femtosecond laser ablation of bulk MoS₂ targets in water. The morphology, crystal structures, chemical, and optical properties of the MoS₂ QDs were characterized by transmission electron microscopy, X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy, UV–vis absorption spectra, and photoluminescence spectra. The analysis results show that highly pure, uniform, and monolayer MoS₂ QDs can be successfully prepared. Moreover, …

Tunable Subnanometer Gap Plasmonic Metasurfaces, Dennis Doyle, Nicholas Charipar, Christos Argyropoulos, Scott A. Trammell, Rafaela Nita, Jawad Naciri, Alberto Piqué, Joseph B. Herzog, Jake Fontana

Department of Electrical and Computer Engineering: Faculty Publications

The index of refraction governs the flow of light through materials. At visible and near-infrared wavelengths the real part of the refractive index is limited to less than 3 for naturally occurring transparent materials, fundamentally restricting applications. Here, we carried out experiments to study the upper limit of the effective refractive index of self-assembled metasurfaces at visible and near-infrared wavelengths. The centimeter-scale metasurfaces were made of a hexagonally close packed (HCP) monolayer of gold nanospheres coated with tunable alkanethiol ligand shells, controlling the interparticle gap from 2.8 to 0.45 nm. In contrast to isolated dimer studies, the macroscale areas allow …

Flatland Plasmonics And Nanophotonics Based On Graphene And Beyond, Pai-Yen Chen, Christos Argyropoulos, Mohamed Farhat, J. Sebastian Gomez-Diaz

Department of Electrical and Computer Engineering: Faculty Publications

In this paper, we review and discuss how the recently discovered two-dimensional (2D) Dirac materials, particularly graphene, may be utilized as new efficient platforms for excitations of propagating and localized surface plasmon polaritons (SPPs) in the terahertz (THz) and mid-infrared (MIR) regions. The surface plasmon modes supported by the metallic 2D materials exhibit tunable plasmon resonances that are essential, yet missing, ingredients needed for THz and MIR photonic and optoelectronic devices. We describe how the atomically thin graphene monolayer and metamaterial structures based on it may tailor and control the spectral, spatial, and temporal properties of electromagnetic radiation. In the …

Higher C-Reactive Protein Levels Predict Postoperative Delirium In Older Patients Undergoing Major Elective Surgery: A Longitudinal Nested Case-Control Study, Simon T. Dillon, Sarinnapha M. Vasunilashorn, Long Ngo, Hasan H. Otu, Sharon K. Inouye, Richard N. Jones, David C. Alsop, George A. Kuchel, Eran D. Metzger, Steven E. Arnold, Edward R. Marcantonio, Towia A. Libermann

Department of Electrical and Computer Engineering: Faculty Publications

Background—Delirium is a common, morbid, and costly postoperative complication.. We aimed to identify blood-based postoperative delirium markers in a nested case control study of older surgical patients using a proteomics approach followed by enzyme-linked immunosorbent assay (ELISA) validation.

Methods and Materials—The Successful Aging after Elective Surgery Study enrolled dementia-free adults age ≥70 undergoing major scheduled non-cardiac surgery (N=566; 24% delirium). Plasma was collected at 4 timepoints: preoperatively (PREOP), post-anesthesia care unit (PACU), postoperative day 2 (POD2) and 1 month follow-up (PO1MO). Matched pairs were selected for the independent discovery (39 pairs) and replication cohorts (36 pairs), which were …

Formation Of Aggregated Nanoparticle Spheres Through Femtosecond Laser Surface Processing, Alfred T. Tsubaki, Mark A. Koten, Michael J. Lucis, Craig Zuhlke, Natale J. Ianno, Jeffrey E. Shield, Dennis R. Alexander

Department of Electrical and Computer Engineering: Faculty Publications

A detailed structural and chemical analysis of a class of self-organized surface structures, termed aggregated nanoparticle spheres (AN-spheres), created using femtosecond laser surface processing (FLSP) on silicon, silicon carbide, and aluminum is reported in this paper. AN-spheres are spherical microstructures that are 20–100 μm in diameter and are composed entirely of nanoparticles produced during femtosecond laser ablation of material. AN-spheres have an onion-like layered morphology resulting from the build-up of nanoparticle layers over multiple passes of the laser beam. The material properties and chemical composition of the AN-spheres are presented in this paper based on scanning electron microscopy (SEM), focused …

Direct Torque Control Of Ac Electric Machines, Wei Qiao, Zhe Zhang, Liyan Qu

Department of Electrical and Computer Engineering: Faculty Publications

This disclosure features an apparatus including a motor controller to generate control signals to control an electric motor. The motor controller includes a first saturation controller to generate a first saturation controller output based on feedback signals associated with the electric motor. The motor controller further includes a duty ratio modulator coupled to the first saturation controller. The duty ratio modulator is configured to determine activation times for a set of voltage vectors based on the first saturation controller output. The motor controller is configured to generate, at each switching cycle, a control signal based on the set of voltage …

Band-To-Band Transitions, Selection Rules, Effective Mass, And Excitonic Contributions In Monoclinic Β-Ga2o3, Alyssa Mock, Rafal Korlacki, Chad Briley, Vanya Darakchieva, Bo Monemar, Yoshinao Kumagai, Ken Goto, Masataka Higashiwaki, Mathias Schubert

Department of Electrical and Computer Engineering: Faculty Publications

We employ an eigenpolarization model including the description of direction dependent excitonic effects for rendering critical point structures within the dielectric function tensor of monoclinic β-Ga₂O₃ yielding a comprehensive analysis of generalized ellipsometry data obtained from 0.75–9 eV. The eigenpolarization model permits complete description of the dielectric response. We obtain, for single-electron and excitonic band-to-band transitions, anisotropic critical point model parameters including their polarization vectors within the monoclinic lattice. We compare our experimental analysis with results from density functional theory calculations performed using the Gaussian-attenuation-Perdew-Burke-Ernzerhof hybrid density functional. We present and discuss the order of the …

Anisotropy, Phonon Modes, And Lattice Anharmonicity From Dielectric Function Tensor Analysis Of Monoclinic Cadmium Tungstate, Alyssa Mock, Rafal Korlacki, Sean Knight, Mathias Schubert

Department of Electrical and Computer Engineering: Faculty Publications

We determine the frequency dependence of four independent Cartesian tensor elements of the dielectric function for CdWO₄ using generalized spectroscopic ellipsometry within mid-infrared and far-infrared spectral regions. Different single crystal cuts, (010) and (001), are investigated. From the spectral dependencies of the dielectric function tensor and its inverse we determine all long-wavelength active transverse and longitudinal optic phonon modes with A_u and B_u symmetry as well as their eigenvectors within the monoclinic lattice. We thereby demonstrate that such information can be obtained completely without physical model line-shape analysis in materials with monoclinic symmetry. We then augment the …

Use Of Natural Ores As Oxygen Carriers In Chemical Looping Combustion: A Review, Michael J. Matzen, Jessica Pinkerton, Xiaomeng Wang, Yaşar Demirel

Department of Chemical and Biomolecular Engineering: Faculty Publications

Chemical looping combustion (CLC) has gained considerable ground in energy production due to its inherent carbon capture with a minimal energy penalty. The choice of metal oxide used as an oxygen carrier (OC) in CLC has a substantial weight on the overall efficiency of energy production as well as the ultimate cost per MW. While much work has gone into manufacturing synthetic OCs with high fuel conversions, harsh operating conditions and process limitations cause some unavoidable loss of the oxygen carrier. With low production costs and minimal conditioning required, natural ores have grown in interest as cheap alternative oxygen carriers. …

Theoretically Proposed Optimal Frequency For Ultrasound Induced Cartilage Restoration, April D. Miller, Anuradha Subramanian, Hendrik J. Viljoen

Department of Chemical and Biomolecular Engineering: Faculty Publications

Background: Matching the frequency of the driving force to that of the system’s natural frequency of vibration results in greater amplitude response. Thus we hypothesize that applying ultrasound at the chondrocyte’s resonant frequency will result in greater deformation than applying similar ultrasound power at a frequency outside of the resonant bandwidth. Based on this resonant hypothesis, our group previously confirmed theoretically and experimentally that ultrasound stimulation of suspended chondrocytes at resonance (5 MHz) maximized gene expression of load inducible genes. However, this study was based on suspended chondrocytes. The resonant frequency of a chondrocyte does not only depend on the …

Microgrid Control Strategy Study And Controller Design Based On Model Predictive Control, Yitong Shen

Electronic Theses and Dissertations

In the 21st century, because of the exhausting of oil, coal and other non-renewable energy, human beings enter a period of large-scale exploitation and utilization of renewable energy. Renewable energy generation become an important way for new energy utilization, however, as more and more distributed generation connect to power distribution network, the traditional distribution network structure will be changed. A large number of distributed generation applications of modern power electronic technology, have also produced a lot of harmonics to impact the power quality. It will threaten the safe operation of the distribution network and obstruct the utilization of renewable energy. …

Segmental Movement Compensations In Patients With Transtibial Amputation Identified Using Angular Momentum Separation, Brecca M. M. Gaffney

Electronic Theses and Dissertations

Patients with unilateral dysvascular transtibial amputation (TTA) adopt movement compensations that are required to maintain balance and achieve ambulation in the absence of ankle plantar flexion, and result in increased and asymmetric joint loading patterns. As a result, this population is at an increased risk of overuse injuries, such as low back pain (LBP). Clinical gait analysis is used to guide diagnostics in movement retraining following amputation, and is performed using instrumented (research based) or observational analyses (clinically based). However, instrumented analyses are currently impractical in most clinical settings due to expense and computational limitations. This dissertation presents the use …

Detecting Overpressure Zones By Using Model Based Inversion In Kupe Field, New Zealand, Timucin Cakir

Dissertations, Master's Theses and Master's Reports

Overpressure is a significant parameter during a drilling process in oil exploration. This phenomenon happens when pore pressure exceeds the limit of hydrostatic pressure in a formation and causes drastic hazards such as blow outs while drilling. This thesis focuses on the determination of possible overpressure areas and studies at three wells in Kupe Field, which is considered to be a natural-gas field in Taranaki Basin. In an effort to identify potential overpressure zones at the Kupe Field, acoustic impedance responses of 3D seismic data for three wells, along with their well log responses were evaluated.

Seismic inversion plays an …

Vorticella: A Protozoan For Bio-Inspired Engineering, Sangjin Ryu, Rachel E. Pepper, Moeto Nagai, Danielle C. France

Department of Mechanical and Materials Engineering: Faculty Publications

In this review, we introduce Vorticella as a model biological micromachine for microscale engineering systems. Vorticella has two motile organelles: the oral cilia of the zooid and the contractile spasmoneme in the stalk. The oral cilia beat periodically, generating a water flow that translates food particles toward the animal at speeds in the order of 0.1–1 mm/s. The ciliary flow of Vorticella has been characterized by experimental measurement and theoretical modeling, and tested for flow control and mixing in microfluidic systems. The spasmoneme contracts in a few milliseconds, coiling the stalk and moving the zooid at 15–90 mm/s. Because the …

Controllable Energy Absorption Of Double Sided Corrugated Tubes Under Axial Crushing, Hozhabr Mozafari, Shengmao Lin, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

To maximize the controllable energy absorption of corrugation troughs as observed in the single sided corrugated (SSC) tube, we proposed and tested a new structure design, i.e., double-sided corrugated (DSC) tube made of Al 6060-T6 aluminum alloy or CF1263 carbon/epoxy composite. Finite element models were developed to test the mechanical advantage of the DSC tube in comparison with both SSC and classical straight (S) tubes under axial crushing. Results have shown that the total absorbed energy of the DSC aluminum tube with 14 corrugations was 330% and 32% higher than that of the SSC tube with 14 corrugations and the …

Novel Polyethylene Fibers Of Very High Thermal Conductivity Enabled By Amorphous Restructuring, Bowen Zhu, Jing Liu, Tianyu Wang, Shah R. Valloppilly, Shen Xu, Xinwei Wang

Department of Mechanical and Materials Engineering: Faculty Publications

High-thermal-conductivity polymers are very sought after for applications in various thermal management systems. Although improving crystallinity is a common way for increasing the thermal conductivity (k) of polymers, it has very limited capacity when the crystallinity is already high. In this work, by heat-stretching a highly crystalline microfiber, a significant k enhancement is observed. More interestingly, it coincides with a reduction in crystallinity. The sample is a Spectra S-900 ultrahigh-molecular-weight polyethylene (UHMW-PE) microfiber of 92% crystallinity and high degree of orientation. The optimum stretching condition is 131.5 °C, with a strain rate of 0.0129 s−1 to a low strain ratio …

Dislocations Interaction Induced Structural Instability In Intermetallic Al2Cu, Qing Zhou, Jian Wang, Amit Misra, Ping Huang, Fei Wang, Kewei Xu

Department of Mechanical and Materials Engineering: Faculty Publications

Intermetallic precipitates are widely used to tailor mechanical properties of structural alloys but are often destabilized during plastic deformation. Using atomistic simulations, we elucidate structural instability mechanisms of intermetallic precipitates associated with dislocation motion in a model system of Al₂Cu. Interaction of non-coplanar <001> dislocation dipoles during plastic deformation results in anomalous reactions—the creation of vacancies accompanied with climb and collective glide of <001> dislocation associated with the dislocation core change and atomic shuffle—accounting for structural instability in intermetallic Al₂Cu. This process is profound with decreasing separation of non-coplanar dislocations and increasing temperature and is likely to be …

A Rapid And Non-Invasive Method For Measuring The Peak Positive Pressure Of Hifu Fields By A Laser Beam, Hua Wang, Deping Zeng, Ziguang Chen, Zengtao Yang

Department of Mechanical and Materials Engineering: Faculty Publications

Based on the acousto-optic interaction, we propose a laser deflection method for rapidly, non-invasively and quantitatively measuring the peak positive pressure of HIFU fields. In the characterization of HIFU fields, the effect of nonlinear propagation is considered. The relation between the laser deflection length and the peak positive pressure is derived. Then the laser deflection method is assessed by comparing it with the hydrophone method. The experimental results show that the peak positive pressure measured by laser deflection method is little higher than that obtained by the hydrophone, confirming that they are in reasonable agreement. Considering that the peak pressure …

Benchmark Burnishing With Almen Strip For Surface Integrity, Z. Y. Liu, C. H. Fu, M. P. Sealy, Y. Zhao, Y. B. Guo

Department of Mechanical and Materials Engineering: Faculty Publications

Burnishing is a surface treatment process widely used in aerospace, navy and other industries to improve fatigue and corrosion resistance by introducing a compressive residual stress layer. The measurement of residual stress by XRD is expensive, time consuming, and tedious. This work presented a quick method to determine the residual stress by using Almen strips. Inspired by the application of Almen strips in shot peening, deflections of burnished Almen strips under different burnishing conditions were measured. It was found that the deflection of Almen strip reflects the magnitude and penetration depth into subsurface of induced stress. Higher burnishing force, smaller …

The Effect Of Number Of Corrugation On Crashworthiness Of Aluminum Corrugated Tube Under Lateral Loading, Hozhabr Mozafari, Arameh Eyvazian, Abdel Magid Hamouda

Department of Mechanical and Materials Engineering: Faculty Publications

Thin-walled tubes have been developed and are growing in use as new energy absorber structures. The objective of this study is to investigate the energy absorption and crushing characteristics of corrugated tubes with different number of corrugation in a specific length exposed to lateral loading. At the first step, experimental tests were carried out on a corrugated tube with three con'ugations (two inner and one outer) and a tube without corrugation. After that, a finite element model was developed by means of ABAQUS software in order to study the effect of corrugation number on crushing properties of thin-walled tubes. The …

Effects Of Aspect Ratio On The Mode Couplings Of Thin-Film Bulk Acoustic Wave Resonators, Nian Li, Zhenghua Qian, Jiashi Yang

Department of Mechanical and Materials Engineering: Faculty Publications

We studied mode couplings in thin film bulk acoustic wave resonators of a piezoelectric film on a dielectric layer operating with the fundamental thickness-extensional mode. A system of plate equations derived in our previous paper was used which includes the couplings to the unwanted in-plane extension, flexure, fundamental and second-order thickness shear modes. It was shown that the couplings depend strongly on the plate length/thickness ratio. For a relatively clean operating mode with weak couplings to unwanted modes, a series of discrete values of the plate length/thickness ratio should be avoided and these values were determined in the present paper. …

Experimental Study Of Corrugated Metal-Composite Tubes Under Axial Loading, Arameh Eyvazian, Hozhabr Mozafari, Abdel Magid Hamouda

Department of Mechanical and Materials Engineering: Faculty Publications

In this study, crushing behavior of corrugated metal-composite tube was examined experimentally under axial loading condition. Six types of specimens, classified into two groups of metal and metal-composite, were tested under quasi static axial loading. The failure mechanism and failure history of the specimens were presented and discussed. The experimental result showed that corrugated metal composite tubes demonstrate perfect energy absorption characteristics in terms of uniformity of load-displacement diagram, reduction of initial peak load and controlling failure mechanism. Moreover, it was also found that adding filament wound layer of composite on the surface of metallic corrugated tube compensated weakness of …

Clustering On Magnesium Surfaces – Formation And Diffusion Energies, Haijian Chu, Hanchen Huang, Jian Wang

Department of Mechanical and Materials Engineering: Faculty Publications

The formation and diffusion energies of atomic clusters on Mg surfaces determine the surface roughness and formation of faulted structure, which in turn affect the mechanical deformation of Mg. This paper reports first principles density function theory (DFT) based quantum mechanics calculation results of atomic clustering on the low energy surfaces {0001} and {1011}. In parallel, molecular statics calculations serve to test the validity of two interatomic potentials and to extend the scope of the DFT studies. On a {0001} surface, a compact cluster consisting of few than three atoms energetically prefers a facecentered- cubic stacking, to serve as a …

Review Of Sustainability Issues In Non-Traditional Machining Processes, Kamlakar Rajurkar, H. Hadidi, J. Pariti, G. C. Reddy

Department of Mechanical and Materials Engineering: Faculty Publications

Non-traditional machining processes (such as EDM and ECM) provide alternatives or sometimes the only alternative in generating highly complex 3-D features in very difficult-to -machine materials. This paper reviews recently published work on sustainability issues related to these processes. For example in Electrochemical machining (ECM) the effect of sludge generation and selection of dielectric in Electrodischarge machining (EDM) need to be investigated from the sustainability point of view. All processes need to be studied not only for resulting productivity and accuracy but also their environmental impact during product generation and usage. This paper addresses process mechanisms, surface integrity, sensing and …

Target Lesion Calcium Arc Influence The Performance Of Stenting, Pengfei Dong, Shengmao Lin, David L. Wilson, Hiram G. Bezerra, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Percutaneous coronary intervention (PCI) is the most common revascularization procedure, in which, fibrocalcific plaques are found in 17–35% of patients undergoing PCI [1]. Numbers will rise with population aging and prolonged statin treatment. Calcifications often lead to stent under expansion and strut malapposition, with increased risk of thrombosis and in-stent restenosis [2]. Presence of calcium strongly inhibits stent performance, a well-documented metric for outcome [3]. The goal of this work is to develop the finite element models for inspecting the influence of the calcium arc extent on the stenting outcomes, such as the stress and strain distribution within the plaque, …