Engineering Commons^™

A Comprehensive Evaluation Of Hybrid Wetting Configurations On Dropwise Condensation, Karim Khazal Egab

Theses and Dissertations

The heat transfer during condensation on a surface depends on the pattern design of the surface, which can highly influence hydrophobic/hydrophilic wettability. In this study hybrid pattern designs were studied. The relationship between the droplet dynamic and the hybrid pattern design can alter the drainage rates, droplet departure frequencies, and the condensation heat transfer rates. Therefore, two series of hybrid patterned surfaces have been designed, developed, and tested during condensation of water vapor on horizontal copper tubes, and compared to complete dropwise and complete filmwise condensation samples. This is to investigate the design that provides the maximum improvement in the …

Ultra High-Speed Signaling And Return On Technology Investment (Roti) For The Electrical Interconnects Sector, Azniza Abd Aziz

Theses and Dissertations

Demand for smaller platform sizes with increasing bandwidth has driven crosstalk problems that prevent bus performance to scale with Moore’s Law. Several approaches to reduce crosstalk such as the use of shields, differential links, and equalizers have been rejected due to higher cost and power required to overcome the signal integrity impediments at Gigahertz data rates. Eigen-mode signaling based on modal decomposition techniques is the most recent method to mitigate crosstalk that can potentially satisfy the demand for higher data rates from modern technology industry.

The goal of this research is to allow maximum dense routing between packages on PCBs …

Determination And Validation Of High-Pressure Equilibrium Adsorption Isotherms Via A Volumetric System, Hind Jihad Kadhim Shabbani

Theses and Dissertations

Adsorption equilibrium isotherms for N2, CO2, and CH4 on zeolite 13X were investigated at three different temperatures (25.5, 50.5 and 75.5 ̊ C) and a pressure range of (0-6.89475) MPa for CH4 and N2 and in the range of (0-4.82633) MPa for CO2 using built in volumetric apparatus. The results were validated using with a volumetric system (ASAP) at the same temperatures and a pressure up to (160-110) KPa respectively. The experimental results were correlated using three process Langmuir (TPLM). The correlated isotherms were then used to calculate the isosteric heat of adsorption for the three gases on 13X. The …

Stilbenes: Therapeutic Interventions Targeting Amyloid Β Protein Aggregation In Alzheimer’S Disease, Yiying Wang

Theses and Dissertations

Alzheimer’s disease (AD) is the most common form of dementia and accounts for 60-80 % of all dementia cases. In the United States, AD is ranked as the 6th leading cause of death and it is the only one among the top 10 that cannot be prevented, treated or even slowed. All FDA approved drugs focus on attenuating the symptoms for a limited time by regulating neurotransmitters without any intervention with the underlying disease process. A major player in the initiation and development of this debilitating disorder is the misfolding and subsequent aggregating of amyloid-β (Aβ) peptide. This aggregation process …

Improving Peptide Identification By Considering Ordered Amino Acid Usage, Ahmed Al-Qurri

Theses and Dissertations

Proteomics has made major progress in recent years after the sequencing of the genomes of a substantial number of organisms. A typical method for identifying peptides uses a database of peptides identified using tandem mass spectrometry (MS/MS). The profile of accurate mass and elution time (AMT) for peptides that need to be identified will be compared with this database. Restricting the search to those peptides detectable by MS will reduce processing time and more importantly increase accuracy. In addition, there are significant impacts for clinical studies. Proteotypic peptides are those peptides in a protein sequence that are most likely to …

Underwater Cave Mapping And Reconstruction Using Stereo Vision, Nicholas Weidner

Theses and Dissertations

This work presents a systematic approach for 3-D mapping and reconstruction of underwater caves. Exploration of underwater caves is very important for furthering our understanding of hydrogeology, managing efficiently water resources, and advancing our knowledge in marine archaeology. Underwater cave exploration by human divers however, is a tedious, labor intensive, extremely dangerous operation, and requires highly skilled people. As such, it is an excellent fit for robotic technology. The proposed solution employs a stereo camera and a video-light. The approach utilizes the intersection of the cone of video-light with the cave boundaries resulting in the construction of a wire frame …

Ultrathin Graphene Oxide Membranes For Water Purification: Fundamentals & Potential Applications, Weiwei Xu

Theses and Dissertations

To develop ultrathin GO membranes with both high permeation rate and excellent selectivity, it is essential to understand the interlayer nanostructure and its influence on water purification performance. We purposely deposited GO at a fast rate and at a rate ~12 times slower to control the interlayer nanostructure of the resulting membranes. The d-spacing difference between proposed thermodynamically favored interlayer structure which formed at slow deposition rate and another relative randomly packed interlayer structure formed at fast deposition rate were corroborated by XRD, organic vapor deposition, and AFM. Molecular dynamics simulations further confirmed that, in type I structure, functionalized patches …

Statistical Mechanics Of Lipid-Liquid Crystal Systems: From Fundamentals To Sensing Applications, Donya Ohadi Kabir Maghsudlu

Theses and Dissertations

Understanding the thermodynamics of small systems has a well-established history. The non-intuitive behavior of the intensive properties of small systems comprised of less than a few hundred particles has important implications in many areas of engineering and materials science. Nevertheless, many open questions about the thermophysical properties of systems not in the thermodynamic limit remain unanswered. In the first part of this work, we explore the consequences of the coupling of two small subsystems that together make up a larger isolated system through the use of statistical mechanics and molecular dynamics simulations of Lennard-Jones particles in two dimensions. The results …

Pollutant Formation In Oxy-Coal Combustion, Nujhat Choudhury

Theses and Dissertations

With the increasing levels of carbon dioxide (CO2) in the atmosphere, researchers are driven to seek cleaner combustion techniques to burn coal for power generation. Oxy-coal combustion is a promising technique to cut down CO2 emissions. This technology requires the introduction of a pure oxygen (O2) stream and a recycled flue gas stream into the boiler instead of air. Flue gas stream generated from the system will be low in volume and highly concentrated in CO2. Thus, the capture and sequestration process will be facilitated. But, one of the concerns of adopting this technology is the altered chemistry of pollutants …

Characterization Of Subgrade Resilient Modulus For Mepdg And The Effects On Pavement Rutting, Md Mostaqur Rahman

Theses and Dissertations

In 2008, the American Association of State Highway and Transportation Officials (AASHTO) released a modified pavement design method (i.e., the Mechanistic Empirical Pavement Design Guide (MEPDG)) based on Long Term Pavement Performance (LTPP) data from all over the United States. The MEPDG default design parameters developed from the LTPP database are expected to be significantly different than those for South Carolina material, traffic and weather conditions, thus the default design parameters may not be accurate for South Carolina. Therefore, the new pavement design method should be calibrated for South Carolina conditions by performing MEPDG local calibration.

Different input variables should …

Improving Facial Action Unit Recognition Using Convolutional Neural Networks, Shizhong Han

Theses and Dissertations

Recognizing facial action units (AUs) from spontaneous facial expression is a challenging problem, because of subtle facial appearance changes, free head movements, occlusions, and limited AU-coded training data. Most recently, convolutional neural networks (CNNs) have shown promise on facial AU recognition. However, CNNs are often overfitted and do not generalize well to unseen subject due to limited AU-coded training images. In order to improve the performance of facial AU recognition, we developed two novel CNN frameworks, by substituting the traditional decision layer and convolutional layer with the incremental boosting layer and adaptive convolutional layer respectively, to recognize the AUs from …

Non-Destructive Evaluation Of Composites: Predictive Ultrasonic Guided-Waves Modeling, Non-Destructive Material Characterization, And The Application To Aerospace Structures, Darun Barazanchy

Theses and Dissertations

To predict guided wave dispersion curves, it is common to use different solution approaches depending on the material type (isotropic or anisotropic) of the medium in which the wave propagates. The two different solution methods are defined in different domains, frequency-phase velocity domain for isotropic materials and wavenumber-phase velocity domain for anisotropic materials. This may lead to difficulties and unsatisfying results when predicting the dispersion curves for hybrid laminates which contain both isotropic and anisotropic materials. Therefore, a unified formulation defined in the wavenumber-phase velocity domain to accomodate both isotropic and anisotropic materials, as well as hybrid combinations, is desired. …

Advancing Automated Methods For Microrna Profiling, Kia N. Zellars

Theses and Dissertations

The widespread influence of miRNAs in many biological processes and characteristic changes in expression profiles make them potential biomarkers for a range of diseases. With recent discoveries highlighting the enrichment of particular circulating miRNAs in plasma under pathological conditions, there has been a push for technological advances in miRNA profiling studies as a diagnostic tool. A standardized, automated, high-throughput method for miRNA isolation from human plasma samples was developed in this study. Samples were subject to full miRNome profiling utilizing RT-qPCR. These unique findings demonstrate that developing a distinct miRNA biomarker profile for heart failure patients is feasible and holds …

Progressive Failure Analysis Of Composite Materials Using The Puck Failure Criteria, Karan Kodagali

Theses and Dissertations

Fiber reinforced composites have been used in various engineering structures and applications especially in naval, automotive, aeronautical and sports industries. These composite materials generally exhibit brittle damage behavior. The anisotropy in the material and different kinds of failure mechanisms make it difficult to accurately characterize the behavior of composite materials. The present work aims to verify and apply the Puck Failure Criteria using the commercially available finite element package ABAQUS by writing a user-material subroutine in FORTRAN. The model is implemented with different post failure degradation schemes.

In the present work, the progressive failure on composite materials in analyzed using …

Improved N-Type 4h-Sic Epitaxial Layer Radiation Detectors And Noise Analysis Of Front-End Readout Electronics, Khai V. Nguyen

Theses and Dissertations

Schottky barrier radiation detectors were fabricated on n-type 4H-SiC epitaxial layers (12 – 50 μm) grown by hot wall CVD process on highly nitrogen doped 4H-SiC (0001) substrates with 4-8º off-cut towards the ̅ direction. Ni/4H-SiC Schottky barrier radiation detectors, a very low leakage current of 0.18 nA at 250 V bias, revealing low thermal noise, was observed in current-voltage (I-V) measurements. Using a thermionic emission model, junction properties such as barrier height of ≥1.10 eV and an ideality factor of ≤1.29 were determined. An effective carrier concentration of 1.03×1015 cm-3 was calculated by capacitance-voltage (C-V) measurement. Deep level transient …

Integrating Nano-Patterned Ferromagnetic And Ferroelectric Materials For Smart Tunable Microwave Applications, Tengxing Wang

Theses and Dissertations

The wireless communication market has been ever-growing in the recent decades. Radios with high performance and capabilities to support wireless connections are increasingly demanded. Recent developments in wireless communications targeting ubiquitous connections have resulted in ever more complex system structures for supporting multiple frequency bands and standards. Reconfigurable and tunable RF/microwave technologies have the potential to significantly simplify the systems. The main objective of this dissertation is to develop tunable technologies and design concepts, and propose a new design methodology to implement dually electrically tunable microwave components by integrating both selectively patterned ferromagnetic and ferroelectric materials.

The first part of …

Evaluation Of Multicarrier Air Interfaces In The Presence Of Interference For L-Band And C-Band Air-Ground Communications, Hosseinali Jamal

Theses and Dissertations

The use of aeronautical vehicles and systems is continuously growing, and this means current aeronautical communication systems, particularly those operating in the very high frequency (VHF) aviation band, will suffer from severe congestion in some regions of the world. For example, it is estimated that air-to-ground (AG) communication traffic density will at least double by 2035 over that in 2012, based on the most-likely growth scenario for Europe. This traffic growth (worldwide) has led civil aviation authorities such as the FAA in the USA, and EuroControl in Europe, to jointly explore development of future communication infrastructures (FCI). According to international …

Performance Assessment Of Hsrm Concrete Ties Through Finite Element Model Simulations, Adam I. Zeitouni

Theses and Dissertations

Concrete ties have become a promising alternative to timber ties for freight lines with increased curvature, high annual traffic, and large axle loads. They are also widely adopted in passenger lines. High strength (HS) concrete is the material of choice in the fabrication of prestressed concrete railroad ties. The higher strength of the concrete is directly related to higher values of the Elastic Modulus, thus increasing the rigidity of the material. The combination of increased strength, rigidity, and the material brittleness may lead to the development of high amplitude stresses with high gradients, which appears to be a common underlying …

Enhanced Dropwise Condensation Via Wettability Contrast Mechanism, Mohammad Alwazzan

Theses and Dissertations

Condensation heat transfer performance can be improved by many methods including the most common used method, which is by increasing the droplet removal rate of the condensing surface. Commonly, this approached can be achieved by promoting a dropwise condensation mode in which super/hydrophobic coatings can be applied on the entire condenser surface to reduce the surface wettability degree. In this dissertation, two main approaches were adapted to enhance the condensation heat transfer performance of the condensing surface via wettability contrast mechanism. Three approaches of investigation were performed to better understand such dropwise condensation promoter methods.

In the first part, alternative …

Product Qualification And Performance Assessment Of Hsrm Prestressed Concrete Railroad Ties Through Laboratory Testing, Ali Haider Abdulqader

Theses and Dissertations

This study focuses on the performance assessment of prestressed concrete railroad ties made of a newly developed High Strength Reduce Modulus (HSRM) concrete. The HSRM material has been developed by researchers at the University of South Carolina laboratories. The HSRM material was originally considered as a high-performance concrete for highway bridge girders, but it was rejected because it shows very low modulus of elasticity. A current project at USC proposed to use this HSRM material in prestressed concrete railroad ties. The experimental tests during the material development phase of the project showed that the HSRM-HPC has a reduced Modulus of …

Autonomous Driving With A Simulation Trained Convolutional Neural Network, Cameron Franke

University of the Pacific Theses and Dissertations

Autonomous vehicles will help society if they can easily support a broad range of driving environments, conditions, and vehicles.

Achieving this requires reducing the complexity of the algorithmic system, easing the collection of training data, and verifying operation using real-world experiments. Our work addresses these issues by utilizing a reflexive neural network that translates images into steering and throttle commands. This network is trained using simulation data from Grand Theft Auto V~\cite{gtav}, which we augment to reduce the number of simulation hours driven. We then validate our work using a RC car system through numerous tests. Our system successfully drive …

Parkinson's Symptoms Quantification Using Wearable Sensors, Md Nafiul Alam

Theses and Dissertations

Parkinson’s disease (PD) is a common neurodegenerative disorder affecting more than one million people in the United States and seven million people worldwide. Motor symptoms such as tremor, slowness of movements, rigidity, postural instability, and gait impairment are commonly observed in PD patients. Currently, Parkinsonian symptoms are usually assessed in clinical settings, where a patient has to complete some predefined motor tasks. Then a physician assigns a score based on the United Parkinson’s Disease Rating Scale (UPDRS) after observing the motor task. However, this procedure suffers from inter subject variability. Also, patients tend to show fewer symptoms during clinical visit, …

Impact Of Wastewater Strength And Photocatalyst Loading On Decolourization Of Acid Orange 7 By Co-Doped Tio2, Erick Butler, Oliver Mulamba, Yung Tse Hung, Ching Cheng Chen, Yen Pei Fu

Civil and Environmental Engineering Faculty Publications

© 2017, Chemical Publishing Co. All rights reserved. Heterogeneous photocatalysis has proved to be a successful method for the degradation of water pollutants. In this work, the photocatalytic decolourization of acid orange 7 was performed by cobalt-doped titanium dioxide (Co-doped TiO2). The Co-doped TiO2 was synthesized and characterized using X-ray diffraction, scanning electron microscopy, energy diffraction spectroscopy, UV-visible reflective dispersion spectroscopy and adsorption of nitrogen gas. The acid orange 7 was prepared as a synthetic textile wastewater at three initial concentrations (24, 34 and 44 mg/L) with three photocatalyst loadings (0.025 g, 0.050, 0.1 g/100 mL acid orange 7). Results …

Smart Motorway Innovation For Achieving Greater Safety And Hard Shoulder Management, Nicola Callaghan, Thomas Avery, Mark Mulville

Conference papers

"Smart" motorways are becoming more prevalent through technology-driven approaches such as active traffic management (ATM) systems, hard shoulder management (HSM) control systems and digital enforcement cameras. Such technologies are able to monitor and respond to fluctuating traffic conditions by altering the speed limit to smooth traffic flow, activate warning signs to alert users of hazards up ahead and permit the use of the hard shoulder, either permanently or at peak times. This paper investigates smart motorways as a way of reducing congestion achieving greater road safety and improving hard shoulder management. This research is one of the first which deals …

Armagh Observatory: Historic Building Information Modelling For Virtual Learning In Building Conservation, Maurice Murphy, Alain Chenaux, Garrett Keenaghan, V. Gibson, John Butler, C. Pybusr

Conference papers

In this paper the recording and design for a Virtual Reality Immersive Model of Armagh Observatory is presented, which will replicate the historic buildings and landscape with distant meridian markers and position of its principal historic instruments within a model of the night sky showing the position of bright stars. The virtual reality model can be used for educational purposes allowing the instruments within the historic building model to be manipulated within 3D space to demonstrate how the position measurements of stars were made in the 18th century. A description is given of current student and researchers activities concerning on-site …

Current State Of The Art Historic Building Information Modelling, Conor Dore, Maurice Murphy

Conference papers

In an extensive review of existing literature a number of observations were made in relation to the current approaches for recording and modelling existing buildings and environments: Data collection and pre-processing techniques are becoming increasingly automated to allow for near real-time data capture and fast processing of this data for later modelling applications. Current BIM software is almost completely focused on new buildings and has very limited tools and pre-defined libraries for modelling existing and historic buildings. The development of reusable parametric library objects for existing and historic buildings supports modelling with high levels of detail while decreasing the modelling …

Developing Historic Building Information Modelling Guidelines And Procedures For Architectural Heritage In Ireland, Maurice Murphy, A. Corns, John Cahill, K. Eliashvli, Alain Chenaux, C. Pybus, R. Shaw, G. Devlin, A. Deevy, L. Truong-Hong

Articles

Cultural heritage researchers have recently begun applying Building Information Modelling (BIM) to historic buildings. The model is comprised of intelligent objects with semantic attributes which represent the elements of a building structure and are organised within a 3D virtual environment. Case studies in Ireland are used to test and develop the suitable systems for (a) data capture/digital surveying/processing (b) developing library of architectural components and (c) mapping these architectural components onto the laser scan or digital survey to relate the intelligent virtual representation of a historic structure (HBIM). While BIM platforms have the potential to create a virtual and intelligent …

In Vitro Porcine Blastocyst Development In Three-Dimensional Alginate Hydrogels, Jeremy R. Miles, Taylor D. Laughlin, Catherine Sargus-Patino, Angela K. Pannier

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Appropriate embryonic and fetal development significantly impact pregnancy success and, therefore, the efficiency of swine production. The pre-implantation period of porcine pregnancy is characterized by several developmental hallmarks, which are initiated by the dramatic morphological change that occurs as pig blastocysts elongate from spherical to filamentous blastocysts. Deficiencies in blastocyst elongation contribute to approximately 20% of embryonic loss, and have a direct influence on within-litter birth weight variation. Although factors identified within the uterine environment may play a role in blastocyst elongation, little is known about the exact mechanisms by which porcine (or other species’) blastocysts initiate and progress through …

Laboratory And Full Boom-Based Investigation Of Nozzle Setup Error Effects On Flow, Pressure, And Spray Pattern Distribution, Shane H. Forney, Joe D. Luck, Michael F. Kocher, Santosh Pitla

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Pesticide application is an integral part of crop production, and ground-based agricultural boom sprayers are used extensively to apply pesticides to the crop canopy or soil surface across millions of acres in the United States. Efficient application is necessary to minimize costs and limit adverse environmental impacts. The goals of this study were to provide quantified measurements on the effects of nozzle setup errors on spray pattern uniformity and evaluate how laboratory patternator-based simulations would compare to measurements on a full spray boom. More specific objectives were to determine the effects of factors such as nozzle lateral angle, nozzle spacing, …

Tractor Power Take-Off Torque Measurement And Data Acquisition System, James B. W. Roeber, Santosh K. Pitla, R. M. Hoy, J. D. Luck, Michael F. Kocher

Department of Agricultural and Biological Systems Engineering: Faculty Publications

With the mechanization of agricultural operations, agricultural machinery management has become an extensive research field. Sizing tractors and implements to provide the most efficient power transfer has become an ongoing process with advances in technology. Utilization of the rotational power transferred through gear trains from the tractor engine to the power take-off (PTO) shaft is one of the most efficient methods of power transfer to an implement. This research used commercially available torque sensors that were installed on a tractor PTO shaft for measuring the torque delivered to an implement. The torque sensor was calibrated using the Nebraska Tractor Test …