Engineering Commons^™

A Case Study Of Upper-Room Uvgi In Densely-Occupied Elementary Classrooms By Real-Time Fluorescent Bioaerosol Measurements, Chunxiao Su, Josephine Lau, Fang Yu

Durham School of Architectural Engineering and Construction: Faculty Publications

Recently, the requirement to continuously collect bioaerosol samples using shorter response times has called for the use of real-time detection. The decreased cost of this technology makes it available for a wider application than military use, and makes it accessible to pharmaceutical and academic research. In this case study, real-time bioaerosol monitors (RBMs) were applied in elementary school classrooms—a densely occupied environment—along with upper-room ultraviolet germicidal irradiation (UVGI) devices. The classrooms were separated into a UVGI group and a non-UVGI control group. Fluorescent bioaerosol counts (FBCs) were monitored on 20 visiting days over a four-month period. The classroom with upper-room …

Social Sustainability Indicators In Mass Housing Construction, Ali Karji, Asregedew Woldesenbet, Mostafa Khanzadi

Durham School of Architectural Engineering and Construction: Faculty Publications

In the construction industry, buildings constitute more than half of the new construction built in the world. With the rapid growth of population in urban areas and high-energy consumption of buildings, considerable attention and efforts have been devoted to creating a sustainably built environment. As a result, various sustainable rating systems, principles and tools have been developed in recent years. This paper presents efforts underway for evaluation of sustainability in mass housing construction projects in the Middle East from a social aspect. The study reviews reports, guidelines and best practices at national and international levels to detect key sustainability indicators. …

Heat - Pump System With Refrigerant Charge Diagnostics, Fadi M. Alsaleem, Gregg H. Hemmelgarn

Durham School of Architectural Engineering and Construction: Faculty Publications

A heat-pump circuit may include an indoor heat exchanger, an outdoor heat exchanger, a compressor adapted to circulate a working fluid between the indoor and outdoor heat exchangers, and an expansion device disposed between the indoor and outdoor heat exchangers. A monitor for the heat-pump system may include a return-air temperature sensor, a supply-air temperature sensor, and a processor. The return-air temperature sensor may be adapted to measure a first air temperature of air upstream of the indoor heat exchanger. The supply-air temperature sensor may be adapted to measure a second air temperature of air down stream of the indoor …

System Identification Of A Circulation Control Unmanned Aerial Vehicle, Mohammed Agha

Electronic Theses and Dissertations

The advancement in automation and sensory systems in recent years has led to an increase the demand of UAV missions. Due to this increase in demand, the research community has gained interest in investigating UAV performance enhancing systems. Circulation Control (CC), which is an active control flow method used to enhance UAV lift, is a performance enhancing system currently studied. In prior research, experimental studies have shown that Circulation Control wings (CCW) implemented on class-I UAVs can reduce take-off distance by 54%. Wind tunnel tests reveal that CC improves aircraft payload capabilities through lift enhancement. Increasing aircraft payload capabilities causes …

A Methodology For Internet Of Things Business Modeling And Analysis Using Agent-Based Simulation, Mohammed Basingab

Electronic Theses and Dissertations

Internet of Things (IoT) is a new vision of an integrated network covering physical objects that are able to collect and exchange data. It enables previously unconnected devices and objects to become connected using equipping devices with communication technology such as sensors and radio frequency identification tags (RFID). As technology progresses towards new paradigm such as IoT, there is a need for an approach to identify the significance of these projects. Conventional simulation modeling and data analysis approaches are not able to capture the system complexity or suffer from a lack of data needed that can help to build a …

Enhancement Of Antenna Array Performance Using Reconfigurable Slot-Ring Antennas And Integrated Filter/Antennas, Tianjiao Li

Electronic Theses and Dissertations

As modern communication system technology develops, the demand for devices with smaller size, higher efficiency, and more functionality has increased dramatically. In addition, highly integrated RF-front-end modules with a reduced footprint and less transition loss between cascaded devices are desirable in most advanced wireless communication systems. Antenna arrays are widely used in wireless communication systems due to their high directivity and beam steering capability. Moreover, antenna arrays are preferred in mobile communication systems for diversity reception to reduce signal fading effects. In order to meet the various requirements of rapidly developing wireless communication systems, low cost, compact, multifunctional integrated antenna …

Reducing The Overhead Of Memory Space, Network Communication And Disk I/O For Analytic Frameworks In Big Data Ecosystem, Xuhong Zhang

Electronic Theses and Dissertations

To facilitate big data processing, many distributed analytic frameworks and storage systems such as Apache Hadoop, Apache Hama, Apache Spark and Hadoop Distributed File System (HDFS) have been developed. Currently, many researchers are conducting research to either make them more scalable or enabling them to support more analysis applications. In my PhD study, I conducted three main works in this topic, which are minimizing the communication delay in Apache Hama, minimizing the memory space and computational overhead in HDFS and minimizing the disk I/O overhead for approximation applications in Hadoop ecosystem. Specifically, In Apache Hama, communication delay makes up a …

Study Of Periodical Flow Heat Transfer In An Internal Combustion Engine, Xi Luo

Wayne State University Dissertations

In-cylinder heat transfer is one of the most critical physical behaviors which has a direct influence on engine out emission and thermal efficiency for IC engine. In-cylinder wall temperature has to be precisely controlled to achieve high efficiency and low emission. However, this cannot be done without knowing gas-to-wall heat flux. This study reports on the development of a technique suitable for engine in-cylinder surface temperature measurement, as the traditional method is “hard to reach.” A laser induced phosphorescence technique was used to study in-cylinder wall temperature effects on engine out unburned hydrocarbons during the engine transitional period (warm up). …

Improving Usability And Scalability Of Big Data Workflows In The Cloud, Aravind Mohan

Wayne State University Dissertations

Big data workflows have recently emerged as the next generation of data-centric workflow technologies to address the five “V” challenges of big data: volume, variety, velocity, veracity, and value. More formally, a big data workflow is the computerized modeling and automation of a process consisting of a set of computational tasks and their data interdependencies to process and analyze data of ever increasing in scale, complexity, and rate of acquisition. The convergence of big data and workflows creates new challenges in workflow community.

First, the variety of big data results in a need for integrating large number of remote Web …

Additive Manufacturing Of Al 4047 And Al 7050 Alloys Using Direct Laser Metal Deposition Process, Amrinder Singh

Wayne State University Dissertations

Additive manufacturing (AM) of metals is finding numerous applications in automotive and aerospace industry. In 21st century, aluminum is second to steel in automotive sector, because of its high strength to weight ratio. In current era, casted components of Al-Si alloy and high strength Al 7xxx series alloys are being used from low load to high load components. The primary study of this research was to achieve the defect free deposition of Al-Si and Al 7050 alloy. Al-Si alloys samples have been manufactured at lab scale using various additive manufacturing processes, but so far there is no literature available to …

Blown To Bits Project, David Schmidt

Informatics Open Educational Resources

The book, Blown to Bits, uncovers the many ways that the new digital world has changed and is changing our whole environment. Some changes are incremental but others are more revolutionary. Some of the changes that we welcome are slowly eroding our privacy and are changing the rules of ownership. This book illuminates the complexities of these changes. I have attempted to capture the central points in selected chapters, and in some cases I have added new material or new examples to replace dated material. I picked chapters to summarize that address the following topics (and more). There are many …

Analyses Of Pultruded Polyester/ E-Glass Composites Subjected To Environmental Degradation, Cameron Bosley

Electronic Theses and Dissertations

This paper evaluates the response of experimental mold releases for a pultruded glass fiber reinforced polymer (gfrp). The initial assessment criteria include comparisons between pull forces and surface appearances for each mold release. Composites fabricated using experimental mold releases that exhibited acceptable properties for both were used for further mechanical characterization that included environmental aging for two different exposure lengths (500 hours and 1000 hours) in five different environments: UV, bleach, hydrochloric acid, distilled water at 125â°f, and room temperature salt water. Three-point flexural bending and short beam strength tests were undertaken to determine the effects these environments would have …

Development Of A Dynamic Cfd Model For Offshore Oscillating Water Columns With Non-Linear Interactions, Ken O'Connell

Theses

This thesis focuses on the development of a state of the art modelling technique for offshore Oscillating Water Column (OWC) type Wave Energy Converters (WEC) using Computational Fluid Dynamics (CFD). Current literature indicates a limited amount of work has been completed on studying these devices containing non-linear time dependent flow phenomenon. Initially, a 2D Numerical Wave Tank (NWT) is studied to reduce discretisation error in order to reproduce accurately propagating waves. Further development into a 3D domain permits the geometrical requirements of an OWC type spar buoy to be included.

In parallel, a single Degree of Freedom (DOF) model is …

Semiconductor Materials And Devices For 2 Micron Generation, Dzianis Saladukha

Theses

In the last century, semiconductor research has led to significant changes in the fields of communication, medicine, the environment, and many others. Semiconductor devices provide a relatively simple and effective way to convert electrical energy to light and vice versa. Devices based on semiconductor materials of various kinds provide interaction of an electromagnetic signal in the range of wavelengths with a medium. Examples of such devices are LED lamps, photovoltaic cells, thermometers, gas sensors, cameras, and many others. The study of various semiconductors broadens the range of application of photonics. This work is based on the study of materials which …

Tractor Test 2172: John Deere 8400r E23, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Tractor Test 2175: Claas Xerion 5000 Cvt, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Difference Between Male And Female Workers Lifting The Same Relative Load When Palletizing Boxes, André Plamondon, Christian Larivière, Denys Denis, Hakim Mecheri, Iuliana Nastasia

Études primaires

A few biomechanical studies have contrasted the work techniques of female and male workers during manual material handling (MMH). A recent study showed that female workers differed from males mostly in the strategy they used to lift 15-kg boxes from the ground, especially regarding task duration, knee and back postures and interjoint coordination. However, the lifting technique difference observed in females compared to males was perhaps due to a strength differences. The objective of this study was to test whether female workers would repeat the same lifting technique with a load adjusted to their overall strength (females: 10 kg; males: …

Nebraska Summary: S1140 John Deere 6110r, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1142 John Deere 6130r, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1112 John Deere 6155m, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1108 John Deere 6110m, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1159 John Deere 6250r, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2185: Case Ih Steiger 470 Rowtrac, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2179: John Deere 7210r, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2188: Case Ih Steiger 540 Quadtrac, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Development Of Disaster Management In Turkey: From 1999 Kocaeli Earthquake To 2011 Van Earthquake, Mert Tolon, Kağan Cenk Mızrak

Civil Engineering Faculty Publications

The natural disasters that have occurred in Turkey are categorized as % 61 earthquakes, followed by landslides, floods, rock falls, fires and storms. Between the years of 1903 and 2000, there have been nearly 150 earthquakes in Turkey which led to damage and this is a challenge for Turkey. The management and plans of these natural disasters in Turkey were first developed in 1959. In 1999, with the magnitude of 7.4, The Kocaeli and Duzce earthquakes affected a region of Turkey that constitutes % 23 of the country’s population. After that, in 2000 necessary laws have been prepared and enacted. …

Development And Validation Of A Kinetic Model For Enzymatic Hydrolysis Using Candida Rugosa Lipase, Ammar Jamie, Ali Alshami, Zuhair O. Maliabari, Muataz A. Ateih

Chemical Engineering Faculty Publications

Biochemical processing involving enzymatic catalysis of hydrolysis reactions of oils and fats must overcome significant technological barriers before the full benefits of the technology can be realized. Owing to their selectivity and mild reaction conditions, lipases are becoming increasingly important as biocatalysts provided that their kinetics and optimum reaction conditions are well-understood. In this study we report on the development and validation of a kinetic model for the degradation of oils using Candida rugosa lipase, from which a better understanding of the influence of different reaction conditions on hydrolysis kinetics is elucidated. Variations of reaction temperature, mixing speed, enzyme loading …

Semi-Analytical Approach For Time-Dependent Load-Settlement Response Of A Jacked Pile In Clay Strata, Lin Li, Jingpei Li, De'an Sun, Weibing Gong

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Mechanical behavior of the soil around a jacked pile changes significantly during pile installation and subsequent consolidation. Hence, an axially loaded jacked pile exhibits apparent time-dependent bearing performance after pile installation. This paper presents a semi-analytical approach to predict the time-dependent bearing performance of an axially loaded jacked pile in saturated clay strata. The effects of pile installation and subsequent consolidation on the changes in mechanical properties of the surrounding soil are modeled by the cavity expansion theory and the radial consolidation theory, respectively. An exponential function-based load-transfer (t-z) curve is employed to describe the nonlinear behavior of the pile-soil …

Ior Methods In Unconventional Reservoirs Of North America: Comprehensive Review, Dheiaa Alfarge, Mingzhen Wei, Baojun Bai

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Unconventional resources have played a significant role in changing oil industry plans recently. Shale formations in North America have huge oil in place, 900 billion barrels of recoverable oil in Bakken only. However, the predicted primary recovery is still low as less than 10%. Therefore, seeking for improved oil techniques to increase oil recovery in these complex plays is inevitable. In this paper, three stages of review have been combined to find out the applicability of the most feasible IOR methods in these unconventional reservoirs. Firstly, the most common fluid and rock properties of these reservoirs have been investigated and …

Selection Criteria For Miscible-Gases To Enhance Oil Recovery In Unconventional Reservoirs Of North America, Dheiaa Alfarge, Mingzhen Wei, Baojun Bai, Mortadha Alsaba

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Unconventional resources have played a significant role in changing oil industry plans recently. Shale formations in North America such as Bakken, Niobrara, and Eagle Ford have huge oil in place, 100-900 billion barrels of oil in Bakken only. However, the predicted primary recovery is still low as 5-10%. Therefore, seeking for techniques to enhance oil recovery in these complex plays is inevitable. In this paper, two different approaches have been integrated to investigate the feasibility of three different miscible gases which are CO₂, lean gases, and rich gases. Firstly, numerical simulation methods of compositional models have been incorporated …