Engineering Commons^™

System Nonlinear Performance Of Low-Rise Buildings Under Database-Assisted Hurricane Loads, Jing He

LSU Doctoral Dissertations

Light-frame wood buildings account for over 95% of all residential structures in the U.S, of which the majority are designed as low-rise buildings. These low-rise residential buildings in the U.S. have performed unsatisfactorily and are the largest source of the damage and fatality during the past extreme wind events. To deepen the understanding and reduce the vulnerability of the infrastructures, the accurate prediction of the hurricane loss has been an urgent need, and the hurricane catastrophe models are developed in response. However, the current hurricane catastrophe models are focused on the economy loss estimation rather than investigating the root causes …

Stress Analysis Of Embedded Devices Under Thermal Cycling, Sadhana Radhakrishnan

Dissertations and Theses

Embedded active and passive devices has been increasingly used by in order to integrate more functions inside the same or smaller size device and to meet the need for better electrical performance of the component assemblies.

Solder joints have been used in the electronic industry as both structural and electrical interconnections between electronic packages and printed circuit boards (PCB). When solder joints are under thermal cyclic loading, mismatch in coefficients of thermal expansion (CTE) between the printed circuit boards and the solder balls creates thermal strains and stresses on the joints, which may finally result in cracking. Consequently, the mechanical …

Field And Laboratory Testing Of Approaches To Smart Whole-House Mechanical Ventilation Control, Florida Solar Energy Center, Eric Martin

FSEC Energy Research Center®

Whole-house mechanical ventilation is a critical component to a comprehensive strategy for good indoor air quality (IAQ). However, due to lack of integration with standard heating and cooling systems, and perceptions from a portion of the homebuilding industry about risks related to increased energy use, increased cost, and decreased comfort, voluntary and code-required adoption varies amongst regions. Smart ventilation controls (SVC) balance energy consumption, comfort, and IAQ by optimizing mechanical ventilation operation to reduce the heating and/or cooling loads, improve management of indoor moisture, and maintain IAQ equivalence according to ASHRAE 62.2.Suggested Citation:Martin, E.; Fernaughty, K.; Parker, D.; Lubliner, M.; …

A Fast And Robust Extrinsic Calibration For Rgb-D Camera Networks, Po-Chang Su, Ju Shen, Wanxin Xu, Sen-Ching S. Cheung, Ying Luo

Electrical and Computer Engineering Faculty Publications

From object tracking to 3D reconstruction, RGB-Depth (RGB-D) camera networks play an increasingly important role in many vision and graphics applications. Practical applications often use sparsely-placed cameras to maximize visibility, while using as few cameras as possible to minimize cost. In general, it is challenging to calibrate sparse camera networks due to the lack of shared scene features across different camera views. In this paper, we propose a novel algorithm that can accurately and rapidly calibrate the geometric relationships across an arbitrary number of RGB-D cameras on a network. Our work has a number of novel features. First, to cope …

Modeling Multicomponent Fuel Droplet Vaporization With Finite Liquid Diffusivity Using Coupled Algebraic-Dqmom With Delumping, Alanna Y. Cooney, Simcha L. Singer

Mechanical Engineering Faculty Research and Publications

Multicomponent fuel droplet vaporization models for use in combustion CFD codes often prioritize computational efficiency over model complexity. This leads to oversimplifying assumptions such as single component droplets or infinite liquid diffusivity. The previously developed Direct Quadrature Method of Moments (DQMoM) with delumping model demonstrated a computationally efficient and accurate approach to solve for every discrete species in a well-mixed vaporizing multicomponent droplet. To expand the method to less restrictive cases, a new solution technique is presented called the Coupled Algebraic-Direct Quadrature Method of Moments (CA-DQMoM). In contrast to previous moment methods for droplet vaporization, CA-DQMoM solves for the evolution …

Time-Dependent Transportation Network Design Considering Construction Impact, Yi He, Ziqi Song, Lihui Zhang

Civil and Environmental Engineering Faculty Publications

A traditional discrete network design problem (DNDP) always assumes transportation infrastructure projects to be one-time events and ignores travelers’ delays caused by construction work. In fact, infrastructure construction usually lasts for a long time, and the impact on traffic can be substantial. In this paper, we introduce time dimension into the traditional DNDP to explicitly consider the impact of road construction and adopt an overtime policy to add flexibility to construction duration. We address the problem of selecting road-widening projects in an urban network, determining the optimal link capacity, and designing the schedule of the selected projects simultaneously. A time-dependent …

Correlation Of Structure, Function And Protein Dynamics In Gh7 Cellobiohydrolases From Trichoderma Atroviride, T. Reesei And T. Harzianum, Anna S. Borisova, Elena V. Eneyskaya, Suvamay Jana, Silke F. Badino, Jeppe Kari, Antonella Amore, Magnus Karlsson, Henrik Hansson, Mats Sandgren, Michael E. Himmel, Peter Westh, Christina M. Payne, Anna A. Kulminskaya, Jerry Ståhlberg

Chemical and Materials Engineering Faculty Publications

Background: The ascomycete fungus Trichoderma reesei is the predominant source of enzymes for industrial conversion of lignocellulose. Its glycoside hydrolase family 7 cellobiohydrolase (GH7 CBH) TreCel7A constitutes nearly half of the enzyme cocktail by weight and is the major workhorse in the cellulose hydrolysis process. The orthologs from Trichoderma atroviride (TatCel7A) and Trichoderma harzianum (ThaCel7A) show high sequence identity with TreCel7A, ~ 80%, and represent naturally evolved combinations of cellulose-binding tunnel-enclosing loop motifs, which have been suggested to influence intrinsic cellobiohydrolase properties, such as endo-initiation, processivity, and off-rate.

Results: The TatCel7A, ThaCel7A, …

Assessing The Validity Of Pressure-Measuring Insoles In Quantifying Gait Variables, Jessica Deberardinis, Janet S. Dufek, Mohamed B. Trabia, Daniel E. Lidstone

Integrated Health Sciences Faculty Research

Introduction Pressure-measuring insoles can provide a portable alternative to existing gait analysis tools. However, there is disagreement among researchers on their accuracy and the appropriate calibration methods. The purposes of this study were to (1) determine the validity of pressure-measuring insoles for calculating stance time and support-phase impulse during walking using two calibration procedures, and (2) examine the effect of insole size on the results. Methods Data were collected from 39 participants (23.5 ± 3.24 yrs, 66.7 ± 17.5 kg, 1.64 ± 0.09 m), each wearing appropriately sized insoles as they walked over two consecutive force platforms. Two calibration methods …

High-Throughput Production With Improved Functionality And Graphitization Of Carbon Fine Fibers Developed From Sodium Chloride-Polyacrylonitrile Precursors, Mandana Akia, Lee Cremar, Manuel Seas, Jahaziel Villarreal, Mataz Alcoutlabi, Karen Lozano

Mechanical Engineering Faculty Publications

Fine polyacrylonitrile (PAN) fibers were produced through a scalable centrifugal spinning process. Sodium chloride (NaCl) was added to the PAN-dimethylformamide solution to decrease the surface tension and consequently promote a decrease in fiber diameter while increasing the fiber output. The fiber preparation process involved the centrifugal spinning of the PAN-based solution; developed fibers were stabilized in air at 240°C followed by carbonization at 800°C under a Nitrogen atmosphere. The addition of sodium chloride to the PAN solution led to a 37% decrease in the carbon fiber diameter. The carbon fibers were analyzed by scanning electron microcopy, transmission electron microscopy (TEM), …

High-Throughput Production With Improved Functionality And Graphitization Of Carbon Fine Fibers Developed From Sodium Chloride-Polyacrylonitrile Precursors, Mandana Akia, Lee Cremar, Manuel Seas, Jahaziel Villarreal, Alejandra Valdez, Mataz Alcoutlabi, Karen Lozano

Mechanical Engineering Faculty Publications

Fine polyacrylonitrile (PAN) fibers were produced through a scalable centrifugal spinning process. Sodium chloride (NaCl) was added to the PAN-dimethylformamide solution to decrease the surface tension and consequently promote a decrease in fiber diameter while increasing the fiber output. The fiber preparation process involved the centrifugal spinning of the PAN-based solution; developed fibers were stabilized in air at 240°C followed by carbonization at 800°C under a Nitrogen atmosphere. The addition of sodium chloride to the PAN solution led to a 37% decrease in the carbon fiber diameter. The carbon fibers were analyzed by scanning electron microcopy, transmission electron microscopy (TEM), …

The Santa Clara, 2018-01-11, Santa Clara University

The Santa Clara

No abstract provided.

Conductive Contact Area Estimation For Carbon Nanotube Via Interconnects Using Secondary-Electron Imaging, Yusuke Abe, Makoto Suzuki, Anshul Vyas, Cary Y. Yang

Electrical and Computer Engineering

A major challenge for carbon nanotube (CNT) to become a viable replacement of copper and tungsten in the next-generation on-chip via interconnects is the high contact resistance between CNT and metal electrodes. A first step in meeting this challenge is an accurate characterization of via contact resistance. In this paper, the scanning electron microscope (SEM) image contrast at low landing energy is employed to estimate the conductive CNT area inside vias. The total conductive CNT area inside each via is deduced using SEM image with 0.1 keV landing energy and a specified threshold brightness, yielding via resistance versus CNT area …

Spatial Delineation Of Corrosion Zones For Metal Culverts Based On Coastal Louisiana Soil Characteristics, Sanjay Tewari, Francis Manning

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Corrosion of metal pipes used as culverts is a problem that affect many agencies directly involved in designing and maintaining these culverts. The corrosive environment of soil types found in a region could vary in a significant way (mildly corrosive to extremely corrosive) based on soil characteristics. Environmental conditions such as high water table, acidity and presence of various salts could make a soil corrosive to metal pipes. In this article, authors have applied a methodology of processing readily available soil data such as spatial distribution of soil types and soil characteristics (e.g. pH and conductivity) in delineating spatial corrosion …

Seismic Performance Of Hollow-Core Hc-Fcs Columns Having Inner Steel Tube With High Diameter To Thickness Ratio, Mohanad M. Abdulazeez, Mohamed Elgawady

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper experimentally investigates the seismic behavior of a large-scale hollow-core fiber-reinforced polymer-concrete-steel HC-FCS column under seismic cyclic loading. The HC-FCS column consisted of a concrete shell sandwiched between an outer fiber-reinforced polymer (FRP) tube and an inner steel tube. The FRP tube provides continuous confinement for the concrete shell along the height of the column while the steel tube provides the required flexural strength. The tested column has an inner steel tube that had a diameter-to-thickness ratio (D_i/t) (of 254. The seismic performance of the precast HC-FCS column was compared to that of HC-FCS column having(D_{i …}

Purdue’S Biowall, Purdue Ect Team

ECT Fact Sheets Archive

Mechanical ventilation, energy recovery ventilation, and infiltration (air that leaks into a building) are commonly used to introduce fresh air. These are all valid approaches, but a living plant-based filter is an innovative complement to these traditional technologies. A Biowall has the potential to improve indoor air quality while reducing the quantity of air needed for ventilation, creating the potential for energy savings. Figure 1 shows a Biowall prototype being evaluated in the ReNEWW House, a research home located near the Purdue University campus (http://www.renewwhouse.com/).

Mdp (Machine Drive Power) Intelligent Compaction Technology, Purdue Ect Team

ECT Fact Sheets Archive

Caterpillar developed MDP (Machine Drive Power) technology to fill this gap. Rather than an accelerometer and vibratory drum, it uses the principle of rolling resistance to provide indications of soil stiffness. This allows it to perform more reliably on cohesive and granular soils with less variability than accelerometer systems. It also means that the technology can be used on both vibratory and static drum compactors, which are often used on larger sites. While the technology is quite useful on its own, it is even better as a complementary technology to the existing accelerometer-based systems. Contractors who use vibratory soil compactors …

Development Of A Design Guideline For Bridge Pile Foundations Subjected To Liquefaction Induced Lateral Spreading, Jonathan A. Nasr

Dissertations and Theses

Effective-stress nonlinear dynamic analyses (NDA) were performed for piles in liquefiable sloped ground to assess how inertia and liquefaction-induced lateral spreading combine in long-duration vs. short-duration earthquakes. A parametric study was performed using input motions from subduction and crustal earthquakes covering a wide range of earthquake durations. The NDA results were used to evaluate the accuracy of the equivalent static analysis (ESA) recommended by Caltrans/ODOT for estimating pile demands. Finally, the NDA results were used to develop new ESA methods to combine inertial and lateral spreading loads for estimating elastic and inelastic pile demands.

The NDA results showed that pile …

Solid Acid Catalyst Based On Single-Layer Α-Zirconium Phosphate Nanosheets For Biodiesel Production Via Esterification, Yingjie Zhou, Iman Noshadi, Hao Ding, Jingjing Liu, Richard Parnas, Abraham Clearfield, Min Xiao, Yuezhong Meng, Luyi Sun

Henry M. Rowan College of Engineering Departmental Research

In this study, a solid acid was prepared by the sulfonation of surface modified α-zirconium phosphate (ZrP) single-layer nanosheets (SO3H@ZrP), and the prepared solid acid was investigated for the esterification of oleic acid with methanol to produce biodiesel. For comparison, liquid H2SO4 and commercial Amberlyst® 15 catalyst were also evaluated for the same reaction under the same conditions. The experimental results showed that the SO3H@ZrP solid acid catalyst has a superior catalytic efficiency for the esterification reaction, as well as excellent recyclability. The SO3H@ZrP single-layer solid acid catalyst can be uniformly dispersed in the reaction media, but remains heterogeneous and …

Nano-Graphene Oxide And Vitamin D Delivery, Reza Mahdavi, Mehran Solati-Hashjin, Meisam Omidi, Arash Khojasteh, Fateme Fayyazbakhsh

Mechanical and Aerospace Engineering Faculty Research & Creative Works

One of the Most Interesting and Recent Insights into Biomimetic Scaffold Nano-Biomaterial is Smart Scaffolding with Targeted Drug Delivery Ability. in Recent Decades, the Use of Graphene-Based Materials, Such as Nano-Graphene Oxide (NGO), as a Drug Carrier with Amphiphilic Properties, Has Attracted Considerable Attention of Scientists and Researchers in This Field. in Addition, One of the Important Global Problems is Increased Vitamin D Deficiency, Particularly in Pregnant and Postmenopausal Women. Therefore, in This Work, by Considering Hydrophobic Properties of Vitamin D, We Attempted to Examine its Loading and Release Both in the Presence of Surfactant and Surfactant-Free NGO-Aqueous Solution. at …

Improving The Technological Process Of The Fertilizer From Centrifugal Fertilizer Apparatus And Setting The Parameters, B. M. Khudayarov, A. A. Mambetsheripova

Acta of Turin Polytechnic University in Tashkent

The construction of a new pneumoinertial actuating element for fertilizer and their mixtures, as well as results of laboratory tests are presented in this article. Values of basic design and process parameters are determined. Width of fertilizer is being increased to 13m.

Mathematical Model Of The Level Processing Of Organic Wastes On Methanogenesis Mixing Process, Shavkat Imomov, Mansur Sultonov, Akmal Rustamov

Acta of Turin Polytechnic University in Tashkent

The article presents the results of the authors' many experiments on organic waste processing in agriculture. The analysis of the existing biogas plants of advanced countries and comparison of the products obtained during the anaerobic treatment of organic agricultural wastes is presented.

Industrial Conveyors’ Taxonomy And Its Applications, A. Hoshimov, A. Rustamov, J. Rozzokov

Acta of Turin Polytechnic University in Tashkent

In any manufacturing processes includes a material handling equipment that can transport raw material or semi-finished products from the one workstation to another. Material handling equipment are designed based on the type of manufacturing product or the process. Therefore, engineers can easily make decision anaylsis while the selection of the most preferred type of industrial conveyors among others. This paper focuses on the industrial conveyors that classifies all available conveyor types. In this work is defined a review that covers most of the currently available literatures and conveyors types that describes industrial conveyors, types, characteristics and applications. A taxonomy is …

Optimal Control And Design Of Functionality To Improve Efficiency And Lifetime Of Proton Exchange Membrane Fuel Cell, Maftuna Eshkobilova, Uktam Salomov, Maksudbek Baydjanov

Acta of Turin Polytechnic University in Tashkent

This work is devoted to identify operating conditions to maximize the life of power supply, meet the required power output and improve fuel consumption efficiency. We devise a framework for designing fuel cell power supplies for field sensor networks, which have important applications in environmental monitoring, wildlife preservation, in disaster monitoring and in border security. The high efficiency, low emission and zero noise pollution features of fuel cells have made them a promising clean power source. Especially, proton exchange membrane fuel cells are promising alternative to conventional fossil fuel system, because they are clean, quiet and operate high efficiencies. However, …

Development And Implementation Of Non-Contact Measuring Machine In The Automobile Industry Of Gm Uzbekistan, Fazluddin Khusnuddinov, Jasurkhuja Kholkhujaev

Acta of Turin Polytechnic University in Tashkent

The main goal of this project is the introduction of a non-contact measuring machine at GM Uzbekistan plants, which will greatly improve the quality of the cars produced. Increase their competitiveness in the world market, which will increase the export of products. An automated robot with a 3D scanner instead of a probe will be used as a non-contact measuring machine for determining and measuring geometric deviations.

Between The Lines: Tree Rings Hold Clues About A River’S Past | College Of Engineering, Usu College Of Engineering

College of Engineering News

Hydrologists are looking centuries into the past to better understand an increasingly uncertain water future.

Collective Adhesion And Displacement Of Retinal Progenitor Cells Upon Extracellular Matrix Substrates Of Transplantable Biomaterials, Ankush Thakur, Shawn Mishra, Juan Pena, Jing Zhou, Stephen Redenti, Robert Majeska, Maribel Vazquez

Publications and Research

Strategies to replace retinal photoreceptors lost to damage or disease rely upon the migration of replacement cells transplanted into sub-retinal spaces. A significant obstacle to the advancement of cell transplantation for retinal repair is the limited migration of transplanted cells into host retina. In this work, we examine the adhesion and displacement responses of retinal progenitor cells on extracellular matrix substrates found in retina as well as widely used in the design and preparation of transplantable scaffolds. The data illustrate that retinal progenitor cells exhibit unique adhesive and displacement dynamics in response to poly-l-lysine, fibronectin, laminin, hyaluronic acid, and Matrigel. …

Noncontact Three-Dimensional Diffuse Optical Imaging Of Deep Tissue Blood Flow Distribution, Guoqiang Yu, Yu Lin, Chong Huang

Biomedical Engineering Faculty Patents

The present invention provides for three-dimensional reflectance diffuse optical imaging of deep tissue blood flow distribution that removes the need for probe-tissue contact, thereby allowing for such technology to be applied to sensitive, vulnerable, damaged, or reconstructive tissue. The systems utilize noncontact application and detection of near-infrared light through optical lens and detection through a linear array or two-dimensional array of avalanche photodiodes or a two-dimensional array of detectors provided by charge-coupled-device (CCD). Both further feature a finite-element-method (FEM) based facilitation to provide for three-dimensional flow image reconstruction in deep tissues with arbitrary geometries.

Multifunctional Cerium-Based Nanomaterials And Methods For Producing The Same, Matthew O'Keefe, William Fahrenholtz, Carlos E. Castano Londono

Materials Science and Engineering Faculty Research & Creative Works

Embodiments relate to a cerium-containing nano-coating composition, the composition including an amorphous matrix including one or more of cerium oxide, cerium hydroxide, and cerium phosphate; and crystalline regions including one or more of crystalline cerium oxide, crystalline cerium hydroxide, and crystalline cerium phosphate. The diameter of each crystalline region is less than about 50 nanometers.

Mechanisms And Identification Of Unsteady Separation Development And Remediation, Matthew Scott Melius

Dissertations and Theses

Unsteady flow separation represents a highly complex and important area of study within fluid mechanics. The extent of separation and specific time scales over which it occurs are not fully understood and has significant consequences in numerous industrial applications such as helicopters, jet engines, hydroelectric turbines and wind turbines. A direct consequence of unsteady separation is the erratic movement of the separation point which causes highly dynamic and unpredictable loads on an airfoil. Current computational models underestimate the aerodynamic loads due to the inaccurate prediction of the emergence and severity of unsteady flow separation especially in response to a sudden …

Production Of Genetically Engineered Golden Syrian Hamsters By Pronuclear Injection Of The Crispr/Cas9 Complex, Rong Li, Jinxin Miao, Seokhwan Song, Il-Keun Kong, Yaohe Wang, Zhongde Wang

Animal, Dairy, and Veterinary Science Faculty Publications

The pronuclear (PN) injection technique was first established in mice to introduce foreign genetic materials into the pronuclei of one-cell stage embryos. The introduced genetic material may integrate into the embryonic genome and generate transgenic animals with foreign genetic information following transfer of the injected embryos to foster mothers. Following the success in mice, PN injection has been applied successfully in many other animal species. Recently, PN injection has been successfully employed to introduce reagents with gene-modifying activities, such as the CRISPR/Cas9 system, to achieve site-specific genetic modifications in several laboratory and farm animal species. In addition to mastering the …