Engineering Commons^™

Stabilization Of Cr³⁺ Using Iron Rich Slag-Derived Phosphate Cement: An Integrated Solution For Heavy Metals And Hazardous Solid Wastes, Ting Huang, Hongyan Ma, Zhongqiu Luo, Xintao Zhou, Zhengqing He, Peiwen Lv, Xiunan Cai, Pingyan Wang

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

A novel iron-based phosphate cement (IPC), derived from iron-rich smelting slag (ISS), was developed as a sustainable and efficient binder for the stabilization/solidification of trivalent chromium (Cr³⁺). The mechanical properties, hydration behavior, microstructure, leaching toxicity, chromium chemical forms, and environmental safety of chromium-stabilized iron phosphate cement (CIPC) were thoroughly evaluated. The results showed that, with a mass ratio of ISS to ammonium dihydrogen phosphate (ADP) of 2.0, and even with the addition of 20 % chromium nitrate nonahydrate (CN), the compressive strength of CIPC reached 4.2 MPa after curing for 28 d. Furthermore, chromium leaching was well below …

Joint Kinematics And Kinetics During Vertical Jump Landings With Progressively Increasing External Loads, Darcie L. Yount

Dissertations

This study examined sagittal and frontal plane kinematics and kinetics during countermovement jump (CMJ) landings performed with either a traditional barbell (BB) or a hexagonal bar (HEX) across increasing submaximal loads in recreationally active males. Generally, hip and knee flexion angles and joint mean angular velocities decreased as loads increased. Hip extension and knee flexion moments increased as load increased up to 20 kg, at which point these values decreased. Performing the CMJ with the HEX exhibited increased frontal plane stability compared with the BB group. Additionally, the BB group exhibited stiffer landing strategies, with decreased sagittal plane joint angles …

Understanding Structure-Property Relationships Within Polyolefin-Derived Vitrimer Systems, Mikaela Sadri

Dissertations

Polyolefins are extremely ubiquitous materials due to their satisfactory material properties, ease of synthesis, and low cost. Unfortunately, their extensive use has led to a global plastic waste mismanagement problem. As such, notable efforts have recently focused on converting these commodity polymers into vitrimers, or dynamic networks, to extend their use-life and tailor their properties. However, the fundamental polymer physics of these emerging materials, remain largely underexplored, hindering their widespread implementation. To address this challenge and enable a more sustainable future, the overarching goal of my dissertation research is to understand the fundamental structure-property relationships within complex polyolefin-derived vitrimer systems. …

Development And Validation Of A Thermal Model For An Electric Vehicle Powertrain, Claudia Fajardo

Waldo Library Student Exhibits

No abstract provided.

Measurements Of Spinal Posture During Common Strawberry Picking Positions Using Inertial Measurement Units, Madeline E. Everson

Master's Theses

Physically demanding professions, such as agriculture, put people at an increased

risk for experiencing back pain. This is due to the awkward and harmful postures sustained

throughout their workday. While studies have been done demonstrating that back pain is

prevalent amongst this community, most do not collect motion capture (MoCap) data,

leaving the specifics of the kinematics, such as the amount of time spent in harmful

postures, unknown. Unfortunately, MoCap data is typically limited to that of a lab or

facility where the cameras are housed. Therefore, this study aimed to mitigate the

inaccessibility of traditional MoCap by validating that …

High-Heat Transfer Lithium-Ion Batteries: A New Era In Battery Thermal Management, Alfred J. Piggott, Jeffrey S. Allen, Ahmad A. Pesaran

Michigan Tech Publications

Despite advances in lithium-ion battery technology, critical challenges remain that must be addressed to accelerate electric vehicle (EV) adoption and global energy transformation. Significantly improved battery thermal management (BTM) is key to overcoming these challenges. BTM approaches focus on increasing heat transfer coefficients via air, liquid, or refrigerant cooling, but less attention is given to reducing the battery's thermal resistance, a major bottleneck for heat transfer. This work introduces a novel approach to reduce battery thermal resistance by integrating in-plane heat transfer with optimized cell geometry, minimized thermal resistances, and reduced interfacial resistances, representing a departure from previous methods. The …

Mantle Flow And Crustal Deformation Revealed By Seismic Anisotropy In The Subduction Zone Beneath Myanmar, Enbo Fan, Mingming Jiang, Yinshuang Ai, Stephen S. Gao, Kelly H. Liu, Yumei He, Yiming Bai, Guangbing Hou, Yuan Ling, Chit Thet Mon, Myo Thant, Kyaing Sein

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The oblique convergence of the Indian and Eurasian plates drives significant deformation in the crust and mantle beneath Myanmar. However, the crustal deformation in the Indo-Burman Ranges (IBR) and mantle flow beneath Myanmar and adjacent areas remain unclear due to limited studies. We utilized data from the newly deployed second phase of the China-Myanmar Geophysical Survey of the Myanmar Orogen array to perform shear wave splitting analysis of PKS, SKKS, and SKS (XKS) phases. Our results, together with previous findings, provide new insights into mantle flow and crustal deformation across central Myanmar. In the IBR, we observed a transition from …

Ev Charging Management In A Real-Time Optimization Framework Considering Operational Constraints, Hilmi Cihan Güldorum, Ayşe Kübra Erenoğlu, İbrahim Şengör, Barry P. Hayes, Ozan Erdinç

Department of Computer Science Publications

The electrification of transportation plays a central role in the decarbonization of energy systems. Although electric vehicles (EVs) are expected to reduce energy related emissions, the increasing demand imposed by large scale EV adoption presents serious challenges for distribution systems (DSs), which were not originally designed to accommodate such loads. This study proposes a mixed integer quadratically constrained programming (MIQCP) framework to optimize the operation of an EV parking lot (EVPL) under DS constraints. The model compares three widely adopted objective functions: minimization of active power loss, charging cost, and uncontrolled charging impact, which is represented by minimizing the total …

Influence Of Mixing Duration And Absorption Characteristics Of Superabsorbent Polymers On The Fresh And Hardened Properties Of High-Performance Concrete, Yu Cun Gu, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This study investigates the combined influence of superabsorbent polymers (SAPs) with distinct absorption kinetics and extended mixing sequences on the rheological, mechanical, and transport properties of high-performance concrete (HPC). Two SAPs—an ionic acrylamide-co-acrylic acid copolymer (SAP-P) and a non-ionic acrylamide polymer (SAP-B)—were incorporated at an internal curing level of 100%. The impact of extended mixing times (3, 5, and 7 min) following SAP addition was systematically evaluated. Results showed that longer mixing durations led to increased superplasticizer demand and higher plastic viscosity due to continued water absorption by SAPs. However, yield stress remained relatively stable owing to the dispersing effect …

Graduate School Of Engineering And Management Academic Catalog 2025-2026, Graduate School Of Engineering And Management, Air Force Institute Of Technology, Walter F. Jones

AFIT Documents

No abstract provided.

An Inference Approach For Assessing Place-Based Vulnerability To Heat Mortality, Junkang Xu, Chao Fan, Xing Xu, Haoying Han

Publications

A global increase in the frequency, severity, and scale of extreme heat raises concerns about human vulnerability to climate change and associated mortality. Heat vulnerability and mortality have largely been studied separately, lacking an understanding of their causation. Here, we create a non-parametric generalized inference approach that links socioeconomic, environmental, and infrastructure factors articulated in vulnerability theory and heat mortality between 2010 and 2020 for counties across the United States. We find that the lack of vegetation coverages drives mortality in the Southern U.S. and among Hispanic people. Limited air conditioning is a key factor in heat-related mortality among White …

Report On The First Year Of Operation Of Kentucky’S First Utility Wind Turbine, Lawrence E. Holloway, Sophia A. Hahn, Aron Patrick

Electrical and Computer Engineering Faculty Publications

This report examines the first year’s operational data from Kentucky’s first utility wind turbine, the 37 m hub-height 90-kilowatt NPS100C-27, operated by the PPL Corporation Research and Development at their Renewable Integration Research Facility in Mercer County, Kentucky. During that year, the turbine was available 95% of the time, spinning 85% of the time, and generating power 78% of the time, and had a net capacity factor of 11%. This report analyzes the turbine performance and uses the collected wind data to project the performance of an example turbine more typical of larger commercial turbines recently installed elsewhere in the …

Mae Enewsbrief Apr- June 2025, Department Of Mechanical And Aerospace Engineering, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Predicting Miner Localization In Underground Mine Emergencies Using A Hybrid Cnn-Lstm Model With Data From Delay-Tolerant Network Databases, Patrick Nonguin, Samuel Frimpong, Sanjay Madria

Mining Engineering Faculty Research & Creative Works

Underground mining environments are highly hazardous, often prone to gas explosions, cave-ins, and fires that may trap miners during emergencies. The accurate, real-time localization of miners is vital for effective self-escape and rescue operations. Although the Mine Improvement and New Emergency Response (MINER) Act of 2006 mandates communication and tracking systems, most current solutions rely on low-power devices and line-of-sight methods that are ineffective in GPS-denied, dynamic subsurface conditions. Delay-Tolerant Networking (DTN) has emerged as a promising alternative by supporting message relay through intermittent links. In this work, we propose a deep learning framework that combines Convolutional Neural Networks (CNNs) …

Comparative Study On The Long-Term Performance Of Bmd Mixtures Prepared Using Different Sample Preparation Techniques And Superpave Mixtures Under Varying Pavement Structures, Amarjeet Tiwari

Graduate Theses and Dissertations

Asphalt mix design has advanced significantly since the 1930s, with Balanced Mix Design (BMD) emerging to address durability concerns found in the Superpave method by optimizing binder content based on performance criteria. The performance of bituminous mixtures can be assessed through laboratory testing. These tests require proper sample preparation, and various techniques are employed for this purpose. Understanding the differences between these techniques is essential for the successful application of bituminous mixtures in the field. The objective of this study is to assess the differences in the predicted long-term performance of two sample preparation techniques, Lab Mix Lab Compacted (LMLC) …

Analysis And Predictive Modeling Of Stall And Spin Accidents In General Aviation Fixed-Wing Aircraft, Mehedi Hasan

Graduate Theses and Dissertations

Stall and spin accidents represent a persistent safety concern in General Aviation, with approximately 41% resulting in fatalities despite their relatively low occurrence. This study analyzes 1,079 General Aviation stall and spin accidents from 2008 to 2023 using the National Transportation Safety Board accident database. Our analysis identified the top phases of flight, injury outcomes, and causal factors in stall/spin accidents. Findings indicate that over 93% of stall/spin events involved General Aviation aircraft, with most accidents occurring during initial climb, takeoff, or low-altitude maneuvering. Pilot-related control errors, especially poor airspeed and angle-of-attack management, were the most common causes. To assess …

Engineered Interfaces For Enhanced Transient Liquid Phase Bonding In Electronics Assembly, John Russell Harris

Graduate Theses and Dissertations

Growing applications in transportation make power density a key optimization target in the power electronics industry. More power in a shrinking environment leads to high heat flux and junction temperatures that damage silicon-based switching devices. Temperatures approaching 175℃ can result in false triggering of the device’s activated state, resulting in short circuits. Developing wide bandgap semi-conductors, such as gallium nitride and silicon carbide, are less susceptible to this complication as the energy from elevated temperature is a smaller fraction of what would be required to trigger the device. These devices are projected to function reliably in environments of up to …

Photochemical Fabrication And Tribological Evaluation Of Hexagonal Grooves With Corner Dimples On Cast Iron Surfaces, Steven Sonntag

Graduate Theses and Dissertations

The traditional honing process used to texture cylinder liners in internal combustion engines has long been recognized as suboptimal, as evidenced by the need for a break-in period before achieving peak performance. Although laser-based methods can produce micro-scale features with high precision, they are often cost-prohibitive and difficult to scale for large or complex components. This study explores photochemical machining (PCM) as a low-cost, scalable alternative for fabricating high-resolution surface textures—specifically, hexagonal grooves with corner dimples—on gray cast iron. The resulting textures exhibit uniform groove widths (~13 μm) and varied depths, demonstrating PCM’s capability to create high-resolution patterns with sub-micron …

High-Resolution Energy Efficient Selective Laser Sintering Of Copper Nanoparticles, Bo Shen

Graduate Theses and Dissertations

Copper (Cu) is widely utilized in electronics and photonics applications due to its outstanding electrical and thermal conductivity. With increasing demand for miniaturization and higher precision in modern manufacturing, traditional selective laser sintering (SLS) techniques designed primarily for high-throughput production are becoming insufficient. These conventional methods struggle to deliver the resolution required for micro-scale fabrication and often cause thermal damage to sensitive substrates. Therefore, there is a growing necessity to develop compact and high-resolution laser sintering systems capable of precise microfabrication with minimal thermal influence. This study addresses this challenge by investigating nanosecond pulsed laser sintering as a method to …

Computational Study Of Nonlinear Electrokinetic Phenomena In Shear-Thinning Fluids, Wai Yuen Leung

All Theses

Electrokinetic phenomena have been widely used for fluid pumping and particle manipulation in micro/nanofluidic systems. They refer to the motion of fluids or particles in response to an electric field because of the spontaneous formation of an electric double layer at the fluid-solid interface. Understanding electrokinetic phenomena in micro/nanochannels is critical for a wide range of applications across various engineering fields, such as disease diagnostics, contaminant treatment and cell analysis. To date, numerous studies have been reported on electrokinetic phenomena in Newtonian fluids, where the classical Helmholtz-Smoluchowski theory indicates a linear relationship between fluid electroosmosis/particle electrophoresis and electric field. However, …

Life Cycle Assessment Of The Cultivation Of Lettuce In A Hydroponic System Using The Nutrient Film Technique, Raquel Jordan

All Theses

Hydroponic systems are an emerging method of soilless crop cultivation typically done inside a greenhouse where nutrients are delivered dissolved in water rather than being supplied from the soil. Potential benefits of hydroponic systems include reduced irrigation requirements, higher crop yield per area, and the ability to grow crops year-round in nontraditional areas such as urban settings, cold climates, and sites with contaminated soil. However, hydroponic systems tend to have high energy requirements for lighting and climate control, which can yield significant environmental impacts. To explore the environmental impacts of cultivating lettuce in a nutrient film technique (NFT) hydroponic system, …

Polyphenols For The Mitigation Of Vascular Calcification; In Vitro And In Vivo Studies, Abdullah Altuhami

All Theses

Globally, cardiovascular diseases, in most cases associated with calcification, are the main cause of death. However, currently, the only effective cure is to undergo surgery to augment or receive a healthy donor heart, which could be very difficult due to the long waiting list and the associated risks. The possibility of body rejection of the foreign organs is attributed to immunoreaction or the risk of infection, since the donor must be on immunosuppressant drugs that lower the body's immunity and facilitate the body's acceptance of the new organ as one of its own. Taking that into consideration, using tissue-engineered vascular …

Cultivation Of Botryococcus Braunii For The Production Of Hydrocarbons Suitable For Fuel Use, Bryan C. Carroll

All Theses

Energy security, rural poverty, and climate change are pressing issues of our time. Biofuels provide a solution to these issues, with a focus on sustainable aviation fuel, SAF, due to compatibility with aircraft infrastructure and energy density. This research aims to review and produce knowledge about a specific microalga, Botryococcus braunii, for its potential for SAF. First a literature review on the process was conducted followed by an experimental study on the impact of aqueous media and inorganic carbon its growth and hydrocarbon content. The literature review found the process consists of cultivation followed by lipid extraction or hydrothermal …

Evaluating The Impact Of Activated Carbon On The Biodegradation Of Btex Compounds, Megan Barkley

All Theses

BTEX compounds—benzene, toluene, ethylbenzene and xylenes—are toxic, volatile, aromatic hydrocarbons. They are primarily found in petroleum products and can easily enter the environment. Typical remediation techniques include sorption to activated carbon, pump and treat, and bioremediation. Research suggests that combining sorption to activated carbon and bioremediation may enhance BTEX removal. This study evaluates the impact of granular activated carbon (GAC) on the biodegradation of ethylbenzene and toluene, using an enrichment culture of aerobic bacteria.

The main objectives of this study are to grow and maintain a culture that degrades BTEX compounds, evaluate the effect of activated carbon on the biodegradation …

Life Cycle Assessment Of Sustainable Wastewater Systems - Algae-Based Wastewater Treatment, Harish Lakshmi Srinivasan

All Theses

This thesis studies the integration of an algae-based membrane bioreactor (MBR) and photobioreactor system into a domestic wastewater treatment facility, using the Clemson University WWTP as a reference plant. The proposed system replaces the conventional sequencing batch reactor and aerobic digester with a microalgae-bacteria symbiosis process, coupled with submerged ceramic membranes, an algal photobioreactor and anaerobic digestion for enhanced nutrient and energy recovery, which paves the way for water reuse and increased biological capacity in the future.

The study shows that overall energy consumption is reduced by approximately 18% compared to the existing conventional configuration. Further, methane production from anaerobic …

Mission-To-Designs: Automating Uav Conceptual Design Generation, Nana A. Adjei

All Theses

The conceptual design stage of Unmanned Aerial Vehicles (UAVs) is an exploratory phase where designers are tasked with developing and evaluating a wide range of viable design concepts, considering different geometries and configurations based on mission requirements. The goal is to identify the most suitable design after the exploration for further development and progression to the next phase. Several tools and frameworks have been developed to assist designers in this stage, each offering unique capabilities, but all with the common aim of aiding in the efficient development and evaluation of conceptual designs. This is important in the UAV design process …

Resilient Control Framework For Ev Motor Drive System Subject To Cyber-Physical Security, Ali Arsalan

All Dissertations

The electric drive system (EDS) in electric vehicles (EVs) is one of the key safety-critical components. As IoT-enabled communication infrastructure for modern cyber-physical automotive systems continues to evolve, the importance of securing EDS against cyber threats along with physical faults, has become increasingly prominent. Among physical faults, power switches are particularly vulnerable and exhibit the highest susceptibility to open-circuit faults (OCFs). A compromised EDS, whether due to cyber threats or physical issues, can lead to excessive mechanical vibrations, increased thermal stress, fluctuations in electromagnetic torque, and elevated total harmonic distortion. These factors can substantially undermine traction control stability and jeopardize …

Multi-Stage Stochastic Programming For Disaster Relief Logistics Under Forecast Uncertainty, Sudhan Bhattarai

All Dissertations

Hurricanes are among the most destructive annual disasters in the United States, presenting interdependent challenges for evacuation planning and relief-supply logistics. Coordinating evacuation and relief operations is crucial to ensure the timely and effective movement of at-risk populations and the delivery of essential supplies. This dissertation develops and evaluates three progressively advanced multi-stage stochastic programming (MSSP) frameworks that integrate evacuation and relief-item pre-positioning while explicitly accounting for uncertainty in hurricane forecasts.

Chapter 1 introduces a fully adaptive MSSP model for the integrated hurricane relief logistics and evacuation planning (IHRLEP) problem. The model simultaneously optimizes evacuation flows and inventory pre-positioning over …

An Active Quasi-Circulator Ic And Technique For 1-255 Mhz Resonance-Based Spectroscopic Impedance Plethysmography, Sharisse Poff

Theses and Dissertations

Impedance measurement is a promising avenue for noninvasive glucosemonitoring. Specifically,resonance-basedimpedancemeasurements exhibit good correlation with glucose levels at excitations from tens of MHztoover 100 MHz. Additionally, plethysmographic impedance measurements are needed to separate arterial blood signals, which contain strongerglucose information, frominterstitialfluidsignals. Weanticipate that plethysmographic measurements across a range of frequencies— spectroscopic plethysmography—at excitations from tens to over 100 MHz could enable resonance-based monitoring with higher selectivity for arterial glucose than previous work. Afour-point impedance measurement circuit is designed, and its ability to measure constant and periodically time-varying impedance is demonstrated. This circuit presents high impedance to the device-undertest (DUT), which fails …

Performance Evaluation Of Delay-Aware Packet Delivery In Wireless Devices, Alvin Lee

Computer Science and Engineering Master's Theses

As wireless networks, such as WiFi, have evolved from a convenient alternative to wired internet into the backbone of modern digital life, with approximately 19.5 billion devices deployed in 2023, the emergence of Virtual Reality (VR) and Augmented Reality (AR) applications has introduced unprecedented Quality of Service (QoS) demands that challenge existing wireless capabilities. While recent wireless standards have largely addressed throughput limitations, achieving consistent low-latency performance remains a significant challenge.

This thesis focuses on the implementation and performance evaluation of existing solutions to latency bottlenecks in wireless networks, and their impacts on User Datagram Protocol (UDP) and Transmission Control …