Engineering Commons^™

Control-Oriented Automatic Transmission- Based Powertrain Modeling And Simulation With Judder, Harshal B. Kundale

Masters Theses

This work presents automatic transmission-based powertrain modeling. The powertrain consists of an engine, torque converter with lock up clutch, transmission gearbox, propeller shaft, and vehicle body. Simplified powertrain component models are developed for vehicle powertrain dynamic response analysis and future control work. The powertrain components are modeled with algebraic and first order non-linear differential equations. A MATLAB-based powertrain simulation system is developed to investigate the transient characteristics during lock up of torque converter. Simulation results are used in the determination of effects of judder on torque and angular velocity. Clutch judder is a self-excited vibration that occurs during the clutch …

Maintaining Deck Profile In Steel I-Girder Bridges During Deck Placement, Ali Naif Inceefe

Masters Theses

Conventional steel I-girder highway bridges utilize cast-in-place concrete deck. Maintaining the deck profile as per project specifications might be a challenging task. Deformation of girders and formwork used for deck placement need to be controlled during deck placement. Differential deflection between girders, exterior girder web out-of-plane deformation, exterior girder warping, or a combination thereof could impact the deck profile. These deformations challenge maintaining deck profile and need to be considered as a part of constructability evaluation. Determining deck profile due to potential girder deformations is necessary before deck placement so that the remedial actions can be implemented when deck finish …

Large Scale Cryogenic Storage With Active Refrigeration, Adam Swanger

Electronic Theses and Dissertations

Storage and transfer of cryogenic liquefied gases on volume scales from under 10 liters for lab use, up to hundreds of millions of liters for industrial applications is of paramount importance across a vast range of industries. Traditionally, these commodities have been stored at or near the normal boiling point due to relative ease of operation and safety-related considerations; however, this also means that some percentage will always be lost due to environmental heat leaking into the vessel and causing boiloff. These losses become more concerning as scales increase, and are of particular importance for high-cost commodities such helium and …

Comparison Of A Modified And Traditional Rapid Infiltration Basin For Treatment And Control Of Nutrients In Wastewater Effluent, Jessica Cormier

Electronic Theses and Dissertations

Rapid infiltration basins (RIB) have been historically used in Florida for groundwater recharge, effluent disposal, or a combination of both. However, this technique has proven ineffective in providing nitrogen control unless the RIB is modified in some manner. In this study, a traditional RIB was compared to a modified RIB constructed with manufactured biosorption activated media (BAM) to evaluate nitrate removal from reclaimed water. The RIBs are used for reclaimed and excess storm water disposal. Few, if any, studies have been published where BAM-modified RIBs have been used for this purpose. In this work, a mixture of clay, tire crumb, …

Autonomous Discovery And Maintenance Of Mobile Frees-Space-Optical Links, Mahmudur Khan

Electronic Theses and Dissertations

Free-Space-Optical (FSO) communication has the potential to play a significant role in future generation wireless networks. It is advantageous in terms of improved spectrum utilization, higher data transfer rate, and lower probability of interception from unwanted sources. FSO communication can provide optical-level wireless communication speeds and can also help solve the wireless capacity problem experienced by the traditional RF-based technologies. Despite these advantages, communications using FSO transceivers require establishment and maintenance of line-of-sight (LOS). We consider autonomous mobile nodes (Unmanned Ground Vehicles or Unmanned Aerial Vehicles), each with one FSO transceiver mounted on a movable head capable of scanning in …

Application Of Nano-Plasmonics For Sers Bio-Detection And Photocatalysis In The Same Platform, Muhammad R. Shattique

Graduate Theses/Dissertations

Nano-biological systems interfacing nano-structured solid surfaces with biological compounds such as oligonucleotides or proteins are highly regarded as enabling materials for biosensing and biocatalysis applications. In particular, nanostructures of noble metals such as gold or silver, when exposed to light, exhibit a phenomenon known as surface plasmon resonance. When a proper metal nanostructure (plasmonic substrate) is exposed to light, very efficient absorption of incoming photons is possible, resulting in a buildup of localized high-energy regions, or “hot-spots”, where energetic carriers or “hot carriers” can be created. These hot-carriers can be used to catalyze desired chemical transformations in materials located nearby. …

The Effects Of Atmospheric Heat Treatments On Tio2 Nanotube Anodes For Lithium-Ion Batteries, Andreas Savva

Boise State University Theses and Dissertations

The effects of various heat treatments on the physical and electrochemical properties of anatase TiO₂ nanotubes were studied in this work. Well-ordered TiO₂ nanotubes were grown via electrochemical anodization and annealed at 450°C to induce a phase transformation to anatase. The heat treatments were conducted under atmospheres of O₂, Ar, N₂, and water vapor (WV) to create different point defects. The oxygen-deficient atmospheres were used to generate oxygen vacancies in the TiO₂ nanotubes, while the water vapor treatment was used to create Ti vacancies by stabilizing them via the protonation of O sites. …

Systems Engineering Design Of An Electronically Interactive Application For Runway Incursion Prevention, Yixuan Cheng

Doctoral Dissertations and Master's Theses

Runway Incursion is the leading cause of serious incidents or accidents in airports. One of the most common causes of a runway incursion is airport unfamiliarity. Therefore, the researcher designed an electronically interactive application as a practice tool for pilots to utilize during flight preparation. The objective of this application is to enhance airport familiarity to ultimately reduce runway incursion. This application is interactive, affordable, accessible, and mobile device-based. It was designed using the Systems Engineering approach, following Human Factors Engineering principles to make this application user-friendly and to provide optimized human machine interaction. A model-based Systems Engineering software-CORE was …

Evaluation Of Airline Efficiency And Environmental Impacts Using Data Envelopment Analysis, Arun Paul Saini

Doctoral Dissertations and Master's Theses

Airline efficiency has been a focus of research since the birth of the airline industry. Data envelopment analysis has become a highly accepted methodology for performing efficiency analysis and assessing relative differences between comparable business entities; over the last decade, airline efficiency research has proliferated into this linear programming domain. While early airline efficiency research focused primarily on revenue generation and profitability, growing commercial social responsibility is driving greater investment into understanding and improving the environmental impact of airline operations. This study is intended to partially fill a gap in exigent literature. While limited data envelopment analysis including environmental impacts …

Prediction Of Airport Arrival Rates Using Data Mining Methods, Robert William Maxson

Doctoral Dissertations and Master's Theses

This research sought to establish and utilize relationships between environmental variable inputs and airport efficiency estimates by data mining archived weather and airport performance data at ten geographically and climatologically different airports. Several meaningful relationships were discovered using various statistical modeling methods within an overarching data mining protocol and the developed models were tested using historical data. Additionally, a selected model was deployed using real-time predictive weather information to estimate airport efficiency as a demonstration of potential operational usefulness.

This work employed SAS® Enterprise Miner TM data mining and modeling software to train and validate decision tree, neural network, and …

Parametric Study Of Aerodynamic Performance Of An Airfoil With Active Circulation Control Using Leading Edge Embedded Cross-Flow Fan, M.A. Qayyum Mazumder

Doctoral Dissertations and Master's Theses

A concept of a cross-flow fan (CFF) embedded near the leading edge of an airfoil to actively control the boundary layer for lift and thrust enhancement has been proposed. The design places a cross-flow fan near the leading edge of an airfoil and flow is drawn in from the pressure side of the airfoil, energized and expelled out to the suction side near the leading edge. This CFF system simulates the active boundary layer control by blowing commercial computational fluid dynamics (CFD) code ANSYS Fluent is employed to perform 2-D calculations based on various parameters of the CFF and compared …

Development To A Flexible Surface Acoustic Wave Sensor For Strain Sensing, Neha Vedavathi Ramachandran

Doctoral Dissertations and Master's Theses

Surface acoustic wave (SAW) sensors have increasing demand in structural health monitoring due to their passive, variable bandwidth, reliable life-cycle, high accuracy, small size, and light nature. SAW sensors can not only provide the static states of the structural system, such as temperature and pressure but also enable continuous real-time monitoring of dynamic states including strains. SAW sensors are generally fabricated with a rigid piezoceramic substrate, incapable of adapting to highly curved surfaces or flexible objects. The ongoing demands of sensor adaptability with flexible substrates, which is also capable of wireless monitoring, is the basis of the research that can …

A Comprehensive Seismic Response And Slope Stability Analysis Framework For Evaluating The Stability Of Hydraulic-Fill Dams, Sayantan Chakraborty

Civil Engineering Dissertations - Archive

The stability and serviceability of earthen embankment structures such as dams and levees are extremely crucial to avoid the catastrophic consequences of the failure of these structures. Such man-made geo-structures are usually stable under normal working conditions; however, the stability and subsequent functionality may be affected during earthquake events. Hence, the evaluation of seismic response and structural stability of earthen dams is an important facet in the field of geotechnical earthquake engineering. Dams and levees built in earthquake-prone regions are usually designed to withstand expected seismic events, and in-depth time-history-based dynamic analyses are typically performed to assess the behavior of …

Algorithm Development For Sewer Pipe System Condition Assessment Using Multi-Sensor (Msi) Technology, Mohammed Al Asadi

Civil Engineering Dissertations - Archive

This study investigates the performance of all the current large-diameter pipeline system of The City of Arlington (COA) sewer lines of 48 miles (24-inch inner diameter and above for rigid and flexible pipes). Proper inspection and rehabilitation plan for the city sewer pipeline system are better choice for the municipality and tax payers in terms of cost than dealing with pipe damage and collapsing problems when they happen. The City of Arlington (COA), University of Texas at Arlington (UTA) and RedZone Robotics have established a Technology Partnership Program (TPP) to perform a condition assessment on the all COA large diameter …

Sustainability Of Utilizing Renewable And Nuclear Energy In Saudi Arabia Using Different Types Of Life Cycle Assessment, Kamel Almutairi

Graduate Theses and Dissertations

Evaluating the global environmental impacts of the current and future energy policies in Saudi Arabia using Life cycle assessment (LCA) method was the main objective of this dissertation. First, the attributional life cycle assessment (ALCA) framework was used to evaluate the Saudi’s air conditioning systems, as they are responsible for about 70% of the total Saudi residential electricity consumption. The ALCA’s results showed that the AC use phase produces the largest share of the environmental impact and the magnitude of the environmental impacts is influenced by the type of primary fuel used for electricity generation.

Emerging non-fossil sources of electricity …

Efficacy Of Multi-Threshold Null Convention Logic In Low-Power Applications, Brent Bell

Graduate Theses and Dissertations

In order for an asynchronous design paradigm such as Multi-Threshold NULL Convention Logic (MTNCL) to be adopted by industry, it is important for circuit designers to be aware of its advantages and drawbacks especially with respect to power usage. The power tradeoff between MTNCL and synchronous designs depends on many different factors including design type, circuit size, process node, and pipeline granularity. Each of these design dimensions influences the active power and the leakage power comparisons. This dissertation analyzes the effects of different design dimensions on power consumption and the associated rational for these effects. Results show that while MTNCL …

Evaluation Of A Solar Powered Variable Flow Tail Water Recovery System For Furrow Irrigation, Vaishali Kandpal

Graduate Theses and Dissertations

Furrow irrigation is a very common irrigation method for growing crops like soybean, cotton and corn in Arkansas. A major portion of this irrigation water is lost as runoff from the field significantly reducing the irrigation application efficiency. There are various methods of improving irrigation efficiency and one of the methods is using tail-water recovery. A tail-water recovery system utilizes tail-water recovery ditches or pits to collect tail-water which can be re-used for irrigation. However, this method is very labor intensive and has been found to be economically non-feasible for some farms in the past research studies. In order to …

Achieving Universal Liaisons And Healthcare Contact Center Centralization Through The Use Of Decision Support Tools, Jared S. Fiacco

Graduate Dissertations and Theses

Healthcare contact centers often experience a large volume of calls and traditional standardized guidelines can be difficult to follow during an active call. While more common workflows can be memorized, they change often because Healthcare is a dynamic field. Constant updates to workflows, an abundance of different processes and provider preferences, and a fast paced environment can lead Customer Service Liaisons (CSLs) to handle patient inquiries incorrectly. Active decision support tools enable a CSL to follow an updated workflow without needing to navigate through complex guidelines and emails. This research shows that contact center centralization through the use of decision …

Design And Qualification Of A Robust Polyurethane Based Conformal Coating Process For Sodimms, Rajat Dhiman

Graduate Dissertations and Theses

Conformal coatings protect printed circuit board assemblies, including the electronic components that the assemblies are populated with. A variety of materials and application methods can be used to conformally coat assemblies. The process setup is crucial to repeatable process reliability. The manual spray based conformal coating is widely used. This method of application was selected due to its compatibility, affordability, and efficiency with the required application. Polyurethanes, one of the families of conformal coatings, provide resistance against abrasion, heat, and chemicals while reducing the risk of tin whiskers. In order to minimize the need for rework and create an efficient, …

New Era In Designing And Governing Cooling Intensity Of Liquid Quenchants To Decrease Distortion During Hardening Of Steel Parts, Nikolai I. Kobasko, Anatolii A. Moskalenko, P. N. Logvynenko, George E. Totten, Volodymyr V. Dobryvechir

Mechanical and Materials Engineering Faculty Publications and Presentations

It was proved in last decade that very intensive and uniform cooling eliminates quench crack formation and significantly decreases distortion of quenched steel parts as compared with their slow cooling in mineral oils. That opened a new era in design ing and governing cooling intensity of liquid quenchants for strengthening steel parts and decrease their distortion after quenching. The new approaches were developed by authors to provide accelerated and uniform cooling steel parts during quenching by creation on their surface thin insulating layers. For this purpose low concentration of water polymer solutions of inverse solubility are used as a quenchant. …

Micron/Nano Structure Creation Through Dual Pulse Femtosecond Laser Surface Processing, Nicholas Roth

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

A new technique has been developed for creating multiscale micro/nanoscale surfaces on metals. This technique is based on past work in femtosecond laser surface processing (FLSP) and dual pulse laser induced breakdown spectroscopy (LIBS). Using a femtosecond laser, pulse pairs were created with varying pulse separations between 0 ps to 500 ps. The creation of surface structures with dual pulse FLSP was studied on Ag, Cu, Ti, Al, Ni, and 304 stainless steel in relation to pulse separation.

Using dual pulse FLSP micro/nano structures have been created for the first time on silver. The silver structures are multiscale in nature …

Scaling Up An Infrastructure For Controlled Experimentation With Testing Techniques, Wayne D. Motycka

School of Computing: Dissertations, Theses, and Student Research

Software testing research often involves reproducing previous experimental results. Previous work created a repository infrastructure for containment and dissemination of testable research subjects using a private centralized storage mechanism for hosting these test subject archives. While this is a good way to store these subjects it can be inefficient when the size of subjects increases or the number of versions of the subject’s source code is large. The delivery of these large subjects from a centralized repository can be quite large and on occasion may not succeed requiring the user to repeat the download request. Coupled with the limited resources …

Academic Interests, Career Choices And Job Opportunities, Doyel Pal, Praveenkumar Khethavath

Open Educational Resources

This assignment is designed for students in First Year Seminar for Engineering and Computer Science. The main goal of the assignment is to introduce students to their major and stimulating their interests related to career choices and academics. This will give students a chance to develop integrative learning skills by making connections between their major and respective career opportunities. This assignment will use new features of ePortfolio to enhance student’s creativity by customizing everything from background, photos, fonts, text, portfolio content etc. Instead of a uniform profile, each students’ page will reflect the distinct visual representation of their personality, brand, …

First Principles-Based Microkinetic Modeling Of Ethanol From Syngas On Bimetallic Co-Pd Catalysts, Anuradha Gundamaraju

All Dissertations

In the future, the availability of reliable alternative fuels will be crucial for any country to become energy independent. One such alternative is ethanol as it can be used both as a fuel and as a fuel additive. Most of the ethanol produced in the world today is derived from biomass. The biomass feedstocks and fermentation broths used in ethanol production both contain high amounts of water and therefore, the energy efficiency of the process is lessened by product separation processes (azeotropic separation of water and ethanol) that are non-trivial and highly inefficient (due to the evaporation of water). An …

Hybrid Perovskite Characterization And Device Applications., Kasun Fernando

Electronic Theses and Dissertations

Hybrid perovskites are a group of materials that has shown a great impact in the field of scientific research in the past decade due to the efficiency gain within a short period of time. Hot casting is one technique that has been producing high efficient and stable solar cells. Electrical transportation of lateral device structure by such film is explored to understand basic properties and predict possible device applications using it. Under dark, memristive ability of the film was explored using various experiments. Unique uni-polar memristor ability was observed. Using the experimental results, a model is hypothesized using the concepts …

Temperature Effects On Helium Filled Soap Bubble Particle Tracking Velocimetry., Michael C. Blum

Electronic Theses and Dissertations

Helium Filled Soap Bubble (HFSB) Particle Tracking Velocimetry (PTV) methods are becoming increasingly popular as they provide a low cost, safe option for reliable flow visualization. Several studies have been conducted to understand the accuracy of such systems under normal temperatures and pressures; however, no such studies to date have examined accuracy of HFSB PTV at high temperatures. The goal of this study is to characterize the capability of HFSB PTV methods to visualize air flow through a rectangular duct at elevated temperature. A heated wind tunnel was designed to heat up to 150 m³/h of 25 °C …

A Non-Equilibrium Molecular Dynamics Study Of The Effects Of Helium Bubbles On The Thermal Conductivity Of Zrc, Tate Shorthill

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

Zirconium carbide (ZrC) has been proposed as a potential improvement to nuclear fuel cladding. As such, it is important to characterize its physical properties, particularly those relating to thermal energy transport. Reactor conditions are known to damage fuel microstructure over time. While research has been conducted on undamaged and damaged ZrC, some areas of interest remain. Fission products, such as helium, can accumulate in pores within the fuel microstructure. Such a case has yet to be characterized in ZrC fuel cladding.

A non-equilibrium molecular dynamics model was developed to characterize the thermal properties of ZrC. Fourier’s Law allows the thermal …

Validation Of 16 Degree Arced Labyrinth Weir Coefficients, Megan Gordon Montgomery

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

Labyrinth weirs are frequently used to control flow in spillways. Arced labyrinth weirs have been developed and researched in an effort to pass additional flow. Arced labyrinth weirs are more efficient than labyrinth weirs due to their increased length and improved approach flow conditions. In the past research has been done to develop discharge coefficients, Cd, values for arced labyrinth weirs with varying sidewalls angles (a=6°, 12°, and 20°). The Cd data that has been developed can only be used for those specific geometries tested. The purpose of this study was to develop Cd data for an arced labyrinth weir …

Pyrolysis Of Plastic Waste From Medical Services Facilities Into Potential Fuel And/Or Fuel Additives, Bright Kweku Ansah Baiden

Masters Theses

Limited space and high costs for landfilling as well as increasing regulations in plastic waste disposal, has led to high operating costs for organizations involved in managing plastic waste from medical facilities which led to the need to investigate an alternative option such as pyrolysis. The overall goal of this study was to evaluate pyrolysis as a means to repurpose plastic waste obtained from medical service facilities into fuel and fuel additive compounds, with two objectives involving, (1) to examine the effect of heat input (as voltage) and reaction/residence time; and (2) to evaluate the effect of the plastic waste …

Shipboard Design And Fabrication Of Custom 3d-Printed Soft Robotic Manipulators For The Investigation Of Delicate Deep-Sea Organisms, Daniel M. Vogt, Kaitlyn P. Becker, Brennan T. Phillips, Moritz A. Graule, Randi D. Rotjan, Timothy M. Shank, Erik E. Cordes, Robert J. Wood, David F. Gruber

Publications and Research

Soft robotics is an emerging technology that has shown considerable promise in deep-sea marine biological applications. It is particularly useful in facilitating delicate interactions with fragile marine organisms. This study describes the shipboard design, 3D printing and integration of custom soft robotic manipulators for investigating and interacting with deep-sea organisms. Soft robotics manipulators were tested down to 2224m via a Remotely-Operated Vehicle (ROV) in the Phoenix Islands Protected Area (PIPA) and facilitated the study of a diverse suite of soft-bodied and fragile marine life. Instantaneous feedback from the ROV pilots and biologists allowed for rapid re-design, such as adding ªfingernailsº, …