Engineering Commons^™

The Effect Of Experiential Education On Pilots' Vfr Into Imc Decision-Making, Geoffrey R. Whitehurst, Lori Brown, William G. Rantz, Dominic Nicolai, Jessica M. Bradley

Journal of Aviation/Aerospace Education & Research

In aviation, safety is always a primary consideration, and this is especially true during a pilot’s flight training to instill that safety mentality. However, this means that pilots are restricted by safety policies from encountering difficult weather situations during their training, which could, potentially, improve their weather decision-making skills for avoiding future hazardous weather encounters. Thirty-six general aviation pilots of varying instrument flight experience (IF) were allocated, using stratified random sampling based on their IF, to one of three groups, a control group and two educational treatment intervention groups. The educational treatment interventions were designed to improve the participant’s ability …

Comparative Kinetic Modeling Of Growth And Molecular Hydrogen Overproduction By Engineered Strains Of Thermotoga Maritima, Raghuveer Singh, Rahul Tevatia, Derrick White, Yaşar Demirel, Paul H. Blum

Department of Chemical and Biomolecular Engineering: Faculty Publications

Thermotoga maritima is an anaerobic hyperthermophilic bacterium known for its high amounts of hydrogen (H₂) production. In the current study, the kinetic modeling was applied on the engineered strains of T. maritima that surpassed the natural H₂ production limit. The study generated a kinetic model explaining H₂ overproduction and predicted a continuous fermentation system. A Leudking-Piret equation-based model predicted that H₂ production by Tma200 (0.217 mol-H₂ g^–1-biomass) and Tma100 (0.147 mol-H₂ g^–1-biomass) were higher than wild type (0.096 mol-H₂ g^–1 -biomass) with reduced rates of maltose utilization. …

Concrete Metamaterials: Geometry, Composition, And Production, Guilherme Coleta

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Design And Optimization Of Multi-Winglets, Daniel Hearle

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Structural Changes Within Anode Materials Of Na+ Batteries, Alex L'Antigua

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Design And Development Of An Actuation System For Morphing Flaps, Nate Mcwilliams

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Using Fluorescence Spectroscopy To Determine Concentrations Of Quantum Dot Solutions, Cameron Sawyer

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Functionalizing Mica With Silanes Using Wet Chemistry, John Paul Stepnowski

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Pulsed Power Diagnostics For Fusion Propulsion Experiments, Shelby Westrich

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Design And Preliminary Analysis Of A Morphing Flap, Ethan Wiggins

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

The Impact Of Flipped Learning On Student Academic Performance And Perceptions, Mark J. Dusenbury, Myrna R. Olson

Teaching & Learning Faculty Publications

The purpose of this study was to explore if flipped learning has an impact on aviation students perceptions and academic performance in a human factors course. A total of 81 students from a large Midwestern university participated. The Course Evaluation Survey (CES) was used to measure student perceptions, while course exams were used to measure academic performance. To analyze the data, the researchers use paired sample t-tests, independent sample t-tests, and a MANCOVA. Findings show students in the flipped classroom did not perform better than the lecture classroom. In addition, students in the lecture group had significantly higher overall course …

Design And Manufacturing Of A 3d Printer For Teaching And Research, Rafiqul Noorani, Michael Lynch, Patrick Hodgkiss, Matt Fumo, Christopher Burke

Mechanical Engineering Faculty Works

The goal of this paper is to design and fabricate a 3D printer that will be the most accurate and cost-effective printer possible, while still being faster than the Rapid Prototyping (RP) Lab's Stratasys FDM-1650 at Loyola Marymount University. This project is done to greatly increase the capability of the RP lab in addition to exposing students to the design and fabrication of a 3D printer. To complete the construction of the printer, the design is originally generated in Solidworks to ensure the components would work together effectively and to aid with design selection. The frame is then constructed using …

Cataloging The Degree Of Sensitization Via Electrochemical Reactivation For Studying The Corrosion Behavior Of Inconel 718, Austenitic, And Duplex Stainless Steels, Bradley Lynes

Williams Honors College, Honors Research Projects

Corrosion resistant materials can be expensive, but usually reduce the life cycle cost of metallic assets. However, negligent sensitization of these materials can lead to aggressive, intergranular corrosion. Using the methodology of the double loop electrochemical potentiokinetic reactivation (DL-EPR), this project investigates different steel reinforced bars and Inconel to determine the degree of sensitization after a heat treatment of 900°C for 2 hours. The purpose of this research is to validate and determine the appropriate test parameters for performing further DL-EPR test in the future. Additionally, the kinetics observed for each sample during the DL-EPR test will be analyzed and …

Autonomous Combat Robot, Andrew J. Szabo Ii, Chris Heldman, Tristin Weber, Tanya Tebcherani, Holden Leblanc, Fabian Ardeljan

Williams Honors College, Honors Research Projects

This honors project will also serve as an engineering senior design project.

The objective is to design and build the software and electrical systems for a 60 lb weight class combat robot that will function autonomously and outperform manually driven robots during competition.

While running autonomously, the robot will use LiDAR sensors to detect and attack opponent robots. This robot will also be able to be remote controlled in manual mode. This will mitigate the risk in case the autonomy or sensors fail. LED lights on the robot will indicate whether it is in autonomous or manual mode. The system …

The Smartbobber, Zachary Pyle, Nick Spoutz, Zachary Hutson, Ryan Pascal

Williams Honors College, Honors Research Projects

In short, the fishing bobber connects to a smartphone app (also designed by members on the team) to notify the user of fish bite data via Bluetooth connection. Additionally, the smartBobber is able to set the hook on fish autonomously and alert the user when it does so. This is possible by the use of a linear solenoid that is spring loaded. Circuitry on the bobber detects the pull distance on the plunger of the solenoid and transmits this data to the user in real time. Once the solenoid has passed a certain pull threshold, the solenoid completes a 12V …

Developing A Portable Prototype To Utilize An Electrospun Colorimetric Sensor For The Detection Of Trihalomethanes In Water, Amanda Svensson

Williams Honors College, Honors Research Projects

Trihalomethane (THM) detection in water is important due to the potential health effects caused by their presence, including increased cancer risk. A cheap, quick, and portable method of identifying THM concentration at the Environmental Protection Agency limit of 80 parts per billion (ppb) will improve detection and water treatment. Electrospinning was used to make nanofiber membranes using a 2.6 wt% polypropylene solution. These membranes were utilized in the Fujiwara reaction, which creates a color change in the presence of THMs, to detect the THM bromoform in water. The color intensity of the reaction was quantified for 250 and 80 ppb …

Stormwater Infrastructure And The Threat Of Climate Change, Eric Mccaslin

Williams Honors College, Honors Research Projects

The purpose of this report is to analyze the modernization of stormwater infrastructure systems and the growing impact of climate change on said systems. Growing population rates and increasing urban settlement are leading to the water demand approaching the water supply capacity. Climate change is the root of several potentially severe issues affecting water resources as well as the rapidly increasing coastal and urban populations including but not limited to rising sea levels and the increasing severity and frequency of storms. Many cities, especially older or low income ones, also may not have adequate systems in place to handle the …

Stress Corrosion Cracking Of Stainless-Steel Reinforced Concrete, Nathan Frye

Williams Honors College, Honors Research Projects

Stainless steel rebar is one of the most corrosion resistant reinforcing methods for concrete structures. Stainless steel is used for its chromium content and its ability to form a passive oxide corrosion resistant layer. The presence of chloride is one of the largest attackers of this passive film and able to penetrate concrete due to its porous characteristics. This study evaluates the mechanical performance of different stainless steels relative to their changing environments. It is expected that as chloride concentration values increase, mechanical properties will decrease. This will be tested by performing tensile tests on stainless steel rebar sample that …

Sae Baja Custom Caliper And Upright Design, Katelynn R. Kise

Williams Honors College, Honors Research Projects

The Zips Baja Off-Road Racing team had a successful 2018 season however some aspects of the car needed to be updated and improved for the 2019 season. This reports captures the design cycle performed to improve the cost, integration, and reliability of the front braking caliper and upright.

Effects Of Hofmeister Ions On Transition Temperature Of Two Thermo-Responsive Polymers, Joshua Moser

Williams Honors College, Honors Research Projects

It was hypothesized that through the use of Hofmeister Ions, the lower critical solution temperature (LCST) of poly(vinyl methyl ether) (PVME) and poly(ethylene glycol)- poly(N-isopropylacrylamide) (PEG-b-pNIPAAm) block-copolymer could be controlled. Through literature searches and small lab experiments, our team found that there may be a connection between Hofmeister effects and phase transition of a thermo-responsive polymer. To try and prove this, the lab team decided to take four cations (Mg²⁺,Na⁺, Cs⁺, K⁺) in solution with the thermo-responsive polymers and compared their LCST to solutions of the thermo-responsive polymer in de-ionized …

Hydro-Aeroponic Design, Megan J. Doll, Nathan J. Boring, Meredith B. Taylor, Chancelor L. Sunkle

Williams Honors College, Honors Research Projects

“Aeroponics” is a plant cultivation technique where roots hang suspended in the air while the nutrient solution is delivered in the form of a fine mist. NASA has done experiments in space and found out that plants grow very well with aeroponic technology. However, “Hydroponics” is the most preferred method, where plants are grown in a non-soil medium, and mostly in nutrient liquid that flows through rectangular channels. There are advantages and disadvantages to each system. With the intention of combining the efficiency of aeroponics and the compactness of hydroponics, a hydro-aeroponic system was created to grow spinach and lettuce. …

Expendable 3d Printed Rescue Drone, Matthew Chapman, Nathan Knutty, Matthew Chapman

Williams Honors College, Honors Research Projects

This project team designed a 3D printed, expendable drone capable of flying for 80 minutes with a 5 lb payload in order to deliver rescue supplies to individuals in distress.

Carbon Fiber Monocoque, Dan Brown, Leland Hoffman

Williams Honors College, Honors Research Projects

The University of Akron’s Human Powered Vehicle Team designed a high performing, fully functioning vehicle that is safe, efficient, and practical for the 2018-2019 season. These objectives were the main priorities when it came to the initial stages of designing the vehicle. In addition, the vehicle was designed in accordance with the ASME 2019 Human Powered Vehicle Challenge guidelines to satisfy all the rules and requirements. Additional priorities have been created to teach practical engineering skills and techniques to the students participating in the project through different points in the production process including research, vehicle design, construction, and testing.

The …

Metric Coil Car, Abigail Eberly

Williams Honors College, Honors Research Projects

Coil cars are a vital part of many steel mills. They allow mills to easily transfer a coil from one location to another without the use of a crane, manual labor, or other extraneous forces. Steel Equipment Specialists, or SES, gets multiple orders every year for coil cars. While the general functions and goals of the cars remains consistent, the details, such as the size of the car, the distance between rails, and the weight/ size of the coils differs between each place. Due to this variety, SES has requested a coil car that can easily be manipulated and produced …

Artificial Intelligence Of Stormwater Operations, Eric Bednar

Williams Honors College, Honors Research Projects

The current infrastructure in our country will not be able to adequately support the growing demands of an exponentially increasing population. A rise in population contributes to a greater service demand necessary to treat sanitary sewer waste which in many cases contributes to the flow of combined sewers. When it comes to managing these combined sewers, rain and the snowmelt caused from climate changes are major factors that need to be addressed. Some water treatment facilities do not have the ability to treat the capacities or peak flows that a system experiences, resulting in combined sewer overflows which are both …

Requalification Of Coated Fabrics Using Chemlok 2332 In Place Of Chemlok 233, Daniel Madler

Williams Honors College, Honors Research Projects

Rubber coated fabrics are an essential component in the deicing systems of the aerospace industry. Adhesives cements are applied to a fabric prior to being pressed into a rubber compound that will adhere to the fabric. The resulting fabric maintains the strength of the fabric with the added benefits of elasticity and compatibility from the rubber compound. UTC Aerospace Systems relies on these coated fabrics to create safe deicers for the aerospace industry. Chemlok 233, a now obsolete primer cement, was used extensively in the coated fabrics used by UTC. Materials testing and performance evaluation allowed for a replacement cement, …

Theoretical Study Of Fano Resonance In A Mechanical System, Alex Alberts

Williams Honors College, Honors Research Projects

Resonance conditions are a major area of study in theoretical and experimental investigation. Normally, a resonance condition is characterized by a symmetric shape on either side of the resonance. In some cases, we can observe an asymmetric resonance shape, which is called a Fano resonance. We will study the appearance of Fano resonance in a purely mechanical system. The frequency response of the primary system is approximated using the method of multiple scales focusing on the location of the resonance condition. Then, curve fitting is used to approximate the Fano parameter associated with the system, which provides a measurement of …

Smart Garage Opener, Jacob Wasson

Williams Honors College, Honors Research Projects

The purpose of this research project was to design an anti-theft device that interfaces with a standard garage door opener to allow packages to easily be delivered into a garage in a safe and secure manner. Primary functionality of the device is to use a package’s tracking number and corresponding barcode to open and close a garage door to a preset height so that a package can be delivered inside the garage before it closes. My contribution to the project revolved around the programming and board design of the microcontroller circuit that controls the input and output signals of the …

Compression Set Improvement Of Thermoplastic Vulcanizates For High Temperature Tubing, Mitchell Valaitis

Williams Honors College, Honors Research Projects

It was hypothesized that increasing the curative level of the fluorocarbon rubber (FKM) used in manufacturing of thermoplastic vulcanizate (TPV) materials would decrease the compression set values of the TPV enough for it to be suitable as a flexible, lightweight alternative to high operating temperature thermoset rubber tubing currently being used for power steering hose. First, promising TPV formulations were identified by varying the polyamide (PA) and FKM used in a Brabender mixer. Four different types of polyamide and four different types of FKM were investigated, with two of the FKM types and one polyamide type identified as being promising. …

The Second Wind, Jacob Heiss, Logan Neidert

Williams Honors College, Honors Research Projects

The Second Wind device is a set of sensors and a data processing unit capable of recording data necessary to conduct a simplified version of a complex cardiopulmonary stress test (CPET). This data includes VO2, VCO2, ventilation, and pulse oximetry data. VO2 and VCO2 are the percent, by volume, of oxygen and carbon dioxide in the patient's breath, spirometry is the measure of air flow, and the pulse oximetry data includes heart rate (HR) and percent oxygen in the blood (SpO2). In addition, the device was designed to be portable, so this test could be run from patients’ homes or …