Engineering Commons^™

The Optimized Synthesis Of Copper Nanowire For High-Quality And Fabrication Of Core-Shell Nanowire, Suhyun Lee

Dissertations and Theses

Flexible electronics are the promising technology for prospective application in foldable phones. Currently, indium tin oxide (ITO) has been widely used for electronic devices including flat-panel display. However, it is brittle and expensive. Metal nanowires are considered as alternative materials. Among various metal nanowires, copper nanowires are attractive because of its high electrical conductivity, better flexibility, and low cost compared with ITO. However, copper nanowires are very prone to oxidize, which causes subsequent degradation of electrical conductivity. Due to this oxidation issue, core-shell structure nanowires, which are formed silver shell having high conductivity and low resistivity on the surfaces of …

Founding The Domain Of Ai Forensics, Ibrahim Baggili, Vahid Behzadan

Electrical & Computer Engineering and Computer Science Faculty Publications

With the widespread integration of AI in everyday and critical technologies, it seems inevitable to witness increasing instances of failure in AI systems. In such cases, there arises a need for technical investigations that produce legally acceptable and scientifically indisputable findings and conclusions on the causes of such failures. Inspired by the domain of cyber forensics, this paper introduces the need for the establishment of AI Forensics as a new discipline under AI safety. Furthermore, we propose a taxonomy of the subfields under this discipline, and present a discussion on the foundational challenges that lay ahead of this new research …

Usu Engineering Professor Named Ieee Fellow | College Of Engineering, Utah State University

College of Engineering News

Veteran electrical engineer and Utah State University Professor Rose Hu is among the newly-elected fellows of the Institute of Electrical and Electronics Engineers, known as IEEE. It is the world's largest association of technical professionals with more than 423,000 members in over 160 countries around the world. The grade of Fellow is conferred each year by the IEEE board of directors on members with an extraordinary record of accomplishments. Less than 0.1 percent of IEEE members reach the level of Fellow. The announcement was made Nov. 26.

1/Fnoise Modelling And Characterization For Cmos Quanta Image Sensors, Wei Deng, Eric R. Fossum

Dartmouth Scholarship

This work fits the measured in-pixel source-follower noise in a CMOS Quanta Image Sensor (QIS) prototype chip using physics-based 1/f noise models, rather than the widely-used fitting model for analog designers. This paper discusses the different origins of 1/f noise in QIS devices and includes correlated double sampling (CDS). The modelling results based on the Hooge mobility fluctuation, which uses one adjustable parameter, match the experimental measurements, including the variation in noise from room temperature to –70 °C. This work provides useful information for the implementation of QIS in scientific applications and suggests that even lower read noise is attainable …

Using Machine Learning Classification Methods To Detect The Presence Of Heart Disease, Nestor Pereira

Dissertations

Cardiovascular disease (CVD) is the most common cause of death in Ireland, and probably, worldwide. According to the Health Service Executive (HSE) cardiovascular disease accounting for 36% of all deaths, and one important fact, 22% of premature deaths (under age 65) are from CVD.

Using data from the Heart Disease UCI Data Set (UCI Machine Learning), we use machine learning techniques to detect the presence or absence of heart disease in the patient according to 14 features provide for this dataset. The different results are compared based on accuracy performance, confusion matrix and area under the Receiver Operating Characteristics (ROC) …

Robot Motion Planning In Dynamic Environments, Hao-Tien Lewis Chiang

Computer Science ETDs

Robot motion planning in dynamic environments is critical for many robotic applications, such as self-driving cars, UAVs and service robots operating in changing environments. However, motion planning in dynamic environments is very challenging as this problem has been shown to be NP-Hard and in PSPACE, even in the simplest case. As a result, the lack of safe, efficient planning solutions for real-world robots is one of the biggest obstacles for ubiquitous adoption of robots in everyday life. Specifically, there are four main challenges facing motion planning in dynamic environments: obstacle motion uncertainty, obstacle interaction, complex robot dynamics and noise, and …

Group N: Fluid Flow Testing Apparatus, Jonathan Fleming, Braden Kerr, Abel Soloman

Mechanical Engineering Design Project Class

A fluid flow testing apparatus was needed to accurately test valves relative to the conditions seen in the factory of a local St. Louis brewery. After concept generation, a rotating track that toggled the valve between open and closed was decided on by the team. Construction of an initial prototype was done over 3 weeks with a total budget of 400 USD. The initial prototype satisfied almost all of the performance goals: capable of cycling 200 times without intervention, 1 paper-towel of leakage at most, and upper reservoir level consistency within 10 percent. To improve the initial prototype, the team …

Energy Performance Certification: Misassessment Due To Assuming Default Heat Losses, Ciara Ahern, Brian Norton

Articles

Energy Performance Certificates (EPCs) are issued when dwellings are constructed, sold or leased in the EU. Where the cost of obtaining the required data is prohibitive, EPC assessors use nationally applicable default-values. To ensure that dwellings are not assigned a wrongly-higher EPC rating, a standardised thermal bridging transmittance coefficient (Y-value) is typically adopted for all existing dwellings while worst-case overall heat loss coefficients (U-values) are used. Default U-values are applied to a specific building element type (roof, wall, floor etc.) based on building codes and regulations applicable at time of construction. Due to significant building fabric upgrades, default U-values are …

Monte Carlo And Experimental Analysis Of A Novel Directional Rotating Scatter Mask Gamma Detection System, Julie V. Logan, Darren E. Holland, Larry W. Burggraf, Justin A. Clinton, Buckley E. O'Day Iii

Faculty Publications

Excerpt: This work demonstrates successful experimental operation of a prototype system to identify source direction which was modeled using a library of signals simulated using GEANT and a novel algorithm....

Rapid Characterization Of Dissolved Organic Matter And Precursors To Disinfection By-Products By Fluorescence Technique, Taha Marhaba

Sustainability Seminar Series

Natural organic matter (NOM) in the environment today does not only come from humic sources, but also from non-humic or synthetic sources. The typical total organic carbon (TOC) analysis has been typically used as an aggregate measure of NOM in water. NOM from surface water sources were isolated and fractionated by resin adsorption techniques into hydrophobic acid, hydrophobic neutral, hydrophobic base, hydrophilic acid, hydrophilic neutral and hydrophilic base. The Spectral Fluorescent Signatures (SFS) technique through a database of spectral characteristics specific to each fraction was developed for the identification of the six NOM fractions. Among the main advantages of the …

Zirconia-Based Compositions For Use In Passive NoX Adsorber Devices, Deborah Jayne Harris, David Alastair Scapens, John G. Darab, Mark Crocker, Yaying Ji

Chemistry Faculty Patents

A passive NO_x adsorbent includes: palladium, platinum or a mixture thereof and a mixed or composite oxide including the following elements in percentage by weight, expressed in terms of oxide: 10-90% by weight zirconium and 0.1-50% by weight of least one of the following: a transition metal or a lanthanide series element other than Ce.

Although the passive NO_x adsorbent can include Ce in an amount ranging from 0.1 to 20% by weight expressed in terms of oxide, advantages are obtained particularly in the case of low-Ce or a substantially Ce-free passive NO_x adsorbent.

Bringing Statistical Learning Machines Together For Hydro-Climatological Predictions - Case Study For Sacramento San Joaquin River Basin, California, Balbhadra Thakur, Ajay Kalra, Sajjad Ahmad, Kenneth W. Lamb, Venkat Lakshmi

Civil and Environmental Engineering and Construction Faculty Research

Study region: Sacramento San Joaquin River Basin, California Study focus: The study forecasts the streamflow at a regional scale within SSJ river basin with largescale climate variables. The proposed approach eliminates the bias resulting from predefined indices at regional scale. The study was performed for eight unimpaired streamflow stations from 1962–2016. First, the Singular Valued Decomposition (SVD) teleconnections of the streamflow corresponding to 500 mbar geopotential height, sea surface temperature, 500 mbar specific humidity (SHUM500), and 500 mbar U-wind (U500) were obtained. Second, the skillful SVD teleconnections were screened non-parametrically. Finally, the screened teleconnections were used as the streamflow predictors …

A Wideband, Circularly Polarized, Directive Antenna With A Circular Reflector, Tyler J. Mcpherson, Zabed Iqbal, Sungkyun Lim

Electrical & Computer Engineering: Faculty Publications

A two-element, patch antenna with a single feed is presented to achieve wideband, circular polarization, and uni-directional radiation. The driven element of the antenna has a rotated, corner-truncated radiating patch to achieve circularly polarized radiation with an offset microstrip feedline in the front side. The back side of the driven element comprises a wide hexagonal slot, eight meander tips, and a parasitic patch in the center. A circular reflector is added behind the driven element to increase realized gain toward the front side direction of the driven element. A prototype of the antenna is fabricated for validation. In both simulation …

Double Wall Cooling Of An Effusion Plate With Simultaneous Cross Flow And Impingement Jet Array Internal Cooling, Phil Ligrani, Austin Click, David Ritchie, Federico Liberatore, Rajeshriben Patel, Yin-Hsiang Ho

PRC-Affiliated Research

The present study considers comparisons of hot-side effusion plate results for a mainstream flow passage with CR = 1 and for a mainstream flow passage with CR = 4. The coolant supply arrangement for both CR contraction ratio values includes simultaneous use of cross flow and an impingement jet array. For the effusion cooled/hot surface, presented are spatially-resolved distributions of surface adiabatic film cooling effectiveness, and surface heat transfer coefficients (measured using infrared thermography). These results are given for main flow Reynolds numbers Rems of 89,900 to 95,800. For this main flow Reynolds number range, four different combination values of …

Double Wall Cooling Of An Effusion Plate With Simultaneous Cross Flow And Impingement Jet Array Internal Cooling, Phil Ligrani, Austin Click, David Ritchie, Federico Liberatore, Rajeshriben Patel, Yin-Hsiang Ho

PRC-Affiliated Research

The present study considers comparisons of hot-side effusion plate results for a mainstream flow passage with CR = 1 and for a mainstream flow passage with CR = 4. The coolant supply arrangement for both CR contraction ratio values includes simultaneous use of cross flow and an impingement jet array. For the effusion cooled/hot surface, presented are spatially-resolved distributions of surface adiabatic film cooling effectiveness, and surface heat transfer coefficients (measured using infrared thermography). These results are given for main flow Reynolds numbers Rems of 89,900 to 95,800. For this main flow Reynolds number range, four different combination values of …

Double Wall Cooling Of An Effusion Plate With Simultaneous Cross Flow And Impingement Jet Array Internal Cooling, Phil Ligrani, Austin Click, David Ritchie, Federico Liberatore, Rajeshriben Patel, Yin-Hsiang Ho

PRC-Affiliated Research

The present study considers comparisons of hot-side effusion plate results for a mainstream flow passage with CR = 1 and for a mainstream flow passage with CR = 4. The coolant supply arrangement for both CR contraction ratio values includes simultaneous use of cross flow and an impingement jet array. For the effusion cooled/hot surface, presented are spatially-resolved distributions of surface adiabatic film cooling effectiveness, and surface heat transfer coefficients (measured using infrared thermography). These results are given for main flow Reynolds numbers Rems of 89,900 to 95,800. For this main flow Reynolds number range, four different combination values of …

Pd-Fe3o4/Rgo: A Highly Active And Magnetically Recyclable Catalyst For Suzuki Cross Coupling Reaction Using A Microfluidic Flow Reactor, Hany A. Elazab

Chemical Engineering

There are several crucial issues that need to be addressed in the field of applied catalysis. These issues are not only related to harmful environmental impact but also include process safety concerns, mass and heat transfer limitations, selectivity, high pressure, optimizing reaction conditions, scale-up is-sues, reproducibility, process reliability, and catalyst deactivation and recovery. Many of these issues could be solved by adopting the concept of micro-reaction technology and flow chemistry in the applied catalysis field. A microwave assisted reduction technique has been used to prepare well dispersed, highly active Pd/Fe3O4 nanoparticles supported on reduced graphene oxide nanosheets (Pd-Fe3O4/RGO), which act …

Design And Construction Of A Pilot Scale Mbbr For Tertiary Nitrification, Jeffrey Crandall, Dylan Ellis, Brayden Llewellyn

Biological Engineering

Harmful algal blooms are a growing concern in the US, they are caused by nutrient (nitrogen and phosphorus) accumulation in bodies of water. As a result, stricter effluent restrictions are being placed on nutrient point sources, including wastewater treatment plants. Tertiary nitrification is a solution to meet these new restrictions.

Characterization And Modeling Of The Martensite Transformation In Advanced High-Strength Steels, Stephen Roy Cluff

Theses and Dissertations

Multiple studies on the microstructures of advanced high-strength steels are presented here that seek to add to the already substantial body of knowledge on martensite in steel. These studies seek to gain additional insight into the role that the martensite transformation has on the observed mechanical properties of modern steels. Crystallographic Reconstruction of Parent Austenite Twin Boundaries in a Lath Martensitic Steel The study of post-transformation microstructures and their properties can be greatly enhanced by studying their dependence on the grain boundary content of parent microstructures. Recent work has extended the crystallographic reconstruction of parent austenite in steels to include …

Factor Analysis Of Mixed Data (Famd) And Multiple Linear Regression In R, Nestor Pereira

Dissertations

In the previous projects, it has been worked to statistically analysis of the factors to impact the score of the subjects of Mathematics and Portuguese for several groups of the student from secondary school from Portugal.

In this project will be interested in finding a model, hypothetically multiple linear regression, to predict the final score, dependent variable G3, of the student according to some features divide into two groups. One group, analyses the features or predictors which impact in the final score more related to the performance of the students, means variables like study time or past failures. The second …

Lupd - Leisure Underwater Propulsion Device, James Abraham, Tanner Nordell, Holden Schmidt, Noah Trimark

Mechanical Engineering Design Project Class

The main objective of this Design Project was to create a hands-free, wearable underwater propulsion device. The target consumer is leisure divers, so managing cost was important. Current products on the market do not allow divers to be hands-free while diving and are very expensive. The design process began with an interview with Josh An, a Masters Degree candidate at Washington University in St. Louis. Josh is an avid diver and wanted to see if it was possible to develop a cheap underwater jet pack for leisure diving. After multiple design concepts and mock up prototypes, our team decided on …

Effect Of Incorporating Pottery And Bottom Ash As Partial Replacement Of Cement, Bassam A. Tayeh, Doha M. Alsaffar, Lawend K. Askar, Asmahan Issa Jubeh

Karbala International Journal of Modern Science

This study addressed the environmental constraints in cement produc­tion. Ordinary Portland cement (OPC) was replaced with pottery powder (PP, produced by grinding locally available pottery) and bottom ash (BA) at 10%, 20% and 30% of cement mass. Moreover, 4% calcium chloride solution (CaCl₂.2H₂O) was used as mixing water. Material properties, such as standard consistency, setting time and compressive strength, were measured with different percentages of OPC replacement with PP and BA. Results indicated that the replacement with PP and BA increased the water demand to achieve the standard consistency. These results revealed that the strength evolution …

Artificial Bee Colony Algorithm For Solving Fuzzy Multi-Objective Bed Allocation Model, Abdulhakeem Luqman Hasan

Karbala International Journal of Modern Science

With the improvement of the medical services frameworks rivalry, hospitals face more and more challenges. In the interim, allotment of resource has a crucial influence on performing competitive benefits in a hospitals. To choose the suitable beds number is one of the most essential tasks in hospital administration. Anyway, in true condition, bed allotment choice is a multiple-side problem with weakness and haphazardness of the information available. It is so sophisticated. Therefore, the research about bed allotment difficulty is comparatively rare under considering multiple departments, nursing hours, and stochastic information about arrival and service of patients. In this paper, we …

Stereo Photogrammetry Vs Computed Tomography For 3d Medical Measurements, Doaa Awda Hussien, Fanar M. Abed, Alauldeen A. Hasan

Karbala International Journal of Modern Science

The acquisition of 3D body measurements by computer vision-based remote sensing is becoming extremely substantial in clinical studies nowadays. Thus, accurate 3D models of human anatomical surfaces are required in many clinical routines like disease diagnosis, patient follow-up, surgical planning, computer assisted surgery and different biomechanical applications. These models can be generated from different imaging techniques such as computed tomography (CT). However, 3D conventional medical imaging like CT scan have serious limitations in application such as exposing the patient to ionizing radiation due to repeated scans, highly cost imaging process, failure to provide color texture information, and also lacking to …

Machine Learning On Acoustic Signals Applied To High-Speed Bridge Deck Defect Detection, Yao Chou

Theses and Dissertations

Machine learning techniques are being applied to many data-intensive problems because they can accurately provide classification of complex data using appropriate training. Often, the performance of machine learning can exceed the performance of traditional techniques because machine learning can take advantage of higher dimensionality than traditional algorithms. In this work, acoustic data sets taken using a rapid scanning technique on concrete bridge decks provided an opportunity to both apply machine learning algorithms to improve detection performance and also to investigate the ways that training of neural networks can be aided by data augmentation approaches. Early detection and repair can enhance …

Hf Iq Mixer Vfo Temperature Compensation And Drive Level Optimization For Opposite Sideband Suppression, Katlin Anne-Rostomyan Dahn

Dissertations and Theses

An amateur radio 40m band temperature compensated variable frequency oscillator (VFO) with drive-level optimized for opposite sideband suppression for use as the local oscillator (LO) of a high frequency (HF) IQ image reject mixer is considered in this work. The first problem of this thesis was the discovery of the HF IQ mixer's opposite sideband suppression dependence on LO drive-level. As a solution to this problem, the author built a fixed drive-level VFO for the optimal opposite sideband suppression. This then led to the second problem of this thesis; the discovery by this author of the well-known problem of VFO …

Violin Prosthetic, Justin Kransdorf, Julia Rifkin, Hayden Reynolds, Payal Hukeri

Mechanical Engineering Design Project Class

Sam, an 11-year-old violin player was born without fingers or a thumb on his right hand. In order to learn the basics of violin, he currently uses a custom made prosthetic that allows him to hold a violin bow. However, his current prosthetic does not allow for the bow angle to change relative to his wrist, and thus, he cannot perform many techniques that are important to him furthering his violin skills. Specifically, his prosthetic allows Sam to use only a small percentage of the bow. For this project, a prosthetic was designed for Sam with the goal being to …

Ice Cream Dispensing Machine, Katie Bahnck, Rachel Lockwood, Marie White, Simone Raeth

Mechanical Engineering Design Project Class

Each August, Washington University in St. Louis (WashU) welcomes hundreds of new engineering students to its McKelvey School of Engineering. Historically, during orientation activities, WashU’s Engineering Student Services (ESS) serves dessert bars to the new students, where they must line up and make their own desserts manually. To make the dessert bar more interactive and give students a primer for what their engineering studies hold, we would like to introduce an ice cream sundae making machine to the spread. A semi-automated ice cream machine would allow students to customize their ice cream sundae while observing the everyday mechanics required to …

Automated Whiteboard Eraser, Trent Houpt, Tyler Polasek, Kenny Huang, Rocky Luo

Mechanical Engineering Design Project Class

The Automated Whiteboard Eraser is a product designed to erase whiteboards with the touch of a button. With this product students and teachers will be able to save time and energy as they can continue to work without having to stop and erase. From our research others have attempted to construct similar products. We intend to improve these thoughts and designs in order to build a better and more efficient product.

Board Erasing Device, Mark Fernandez, Christopher Sheffels, Joshua Miller

Mechanical Engineering Design Project Class

The Board Erasing Device is a portable automatic device designed to streamline a university lecturer’s board writing process by automatically erasing whiteboards while they are writing notes on adjacent boards. Our goal during this project was to design, build, and test a portable, automatic, and aesthetically pleasing device compatible with most standard whiteboards on Washington University in St. Louis’ Danforth campus. To that end, with a budget of $400, we created a prototype device to accomplish just that. Our prototype includes a felt eraser, pressed into the whiteboard via magnets. The eraser piece spans all eight feet of width on …