Engineering Commons^™

Removal Of Fluoride From Mine Water Via Adsorption For Land-Applied Soil Amendment, Courtney Golman, Kevin Le, Michelle Dopp, Adrian Damian, Mary Johnson, Jacqueline Payne, Ethan Phan

Chemical Engineering Undergraduate Honors Theses

The process of mining minerals and elements from ores and rocks creates acid rock drainage (ARD). This drainage is water that contains heavy metals and minerals that can be dangerous for human consumption or damaging to the environment. The mining industry has employed various water treatment methods to prevent these metals and minerals from being discharged into water sources such as ponds, lakes, and streams. Currently, the most used treatment process in the mining industry is a cost-effective highdensity sludge (HDS) process. This method reduces the concentration of metals and elements with the use of lime/limestone. However, the concentration of …

Extremely Low Cycle Fatigue Behavior Of Additively Manufactured 17-4ph Stainless Steel, Kaley Collins

Civil Engineering Undergraduate Honors Theses

Steel structures survive seismic loading thanks to components capable of dissipating large amounts of energy through large deformations. Future optimizations of these components include complex free-form geometries that are difficult to fabricate with traditional casting processes. Additive manufacturing (AM) is an alternative for producing optimized free-form geometries. AM material contains significant differences in microstructural characteristics and mechanical behavior compared to its wrought counterparts. Research has been conducted to understand the effect of microscopic features in the high cycle fatigue (HCF) and low cycle fatigue (LCF) regimes. This study focuses on the behavior of 17-4 Precipitation Hardening (PH) stainless steel in …

Multiaxial Fatigue Of Notched Steel Plates And Investigation Of Cfrp Retrofits For Crack Initiation Prevention, Ayumi Fujii

Civil Engineering Undergraduate Honors Theses

Fatigue cracks are cracks that result from repeated loading over time, often following millions of loading cycles. Fatigue cracks occur even if the applied load is not large enough to cause material yield. Once a fatigue crack initiates, resulting stress concentrations at the crack tip often make it difficult to arrest the growth of the crack. In order to prevent growth and propagation of fatigue cracks within structural components, it is necessary to alter the stress condition at the crack tip. Fatigue cracks in steel structures resulting from multiaxial loading and or geometry conditions that result in complex states of …

Preliminary Investigation Of Required Bsca Amount For Soil Cement Mixtures, Mariel Mayori Rivero

Civil Engineering Undergraduate Honors Theses

The recent increase of flooding in the United States and the high expenses related to the damage that these floods have caused to waterway structures suggests a potential interest in rapid setting soil cement to make effective repairs. For this thesis, mix designs of soil only at three different sand-clay proportions were prepared and tested for moisture content and maximum dry density. Due to the early closing of the laboratory and research activities, reliable results were collected from the 70% sand and 30% clay proportions. At those proportions of soil, the optimum moisture content was found to be 8.88% with …

Soil Moisture Content Determination By Means Of The Electromagnetic Spectrum, Julia Loshelder

Civil Engineering Undergraduate Honors Theses

Soil moisture content provides information about the strength, permeability, and compressibility of the soil under investigation. In the research described herein, the relationship between moisture content and reflectance values obtained from spectroscopy was developed to investigate whether in-situ moisture content can be determined in a faster and more efficient way than the current methods. The soil under investigation was laboratory-compacted kaolinite clay mixed with pyranine dye. These specimens were placed beneath an ultraviolet light and a halogen illuminator where reflectance values were collected over a 24-hour period. Correlations were developed from the following methods: 1) spectral indices, 2) continuum analyses …

Understanding Workability In Belitic Calcium Sulfoaluminate Concrete Mixtures, Caleb W. Chesnut

Civil Engineering Undergraduate Honors Theses

Belitic Calcium Sulfoaluminate cement (BCSA) is an emerging technology in the concrete industry. BCSA has similar hardened properties to portland cement (PC) but can set in under 20 minutes and reach 4,000 psi in less than 2 hours. Portland cement accounts for 8% of the world’s CO2 emissions, BCSA cements require less energy to produce. Studies have shown that 40% less CO2 is emitted during the production of BCSA cement than portland cement. This environmental benefit also makes it a very promising PC alternative. Before a new material can be used, designers need to understand the material’s properties. The goal …

Countermeasures For Pedestrian-Involved Accidents On Interstate-Highways, Anna C. Hunter

Civil Engineering Undergraduate Honors Theses

Pedestrian access to the Interstate is prohibited, but many pedestrian-involved accidents still occur on the Interstate in the United States. This project is a case study of West Memphis, Arkansas, which has the second highest occurrence of pedestrian-involved accidents on the Interstate in Arkansas. The study site location includes a segment of Interstate I-40 which is at- grade. The surrounding area contains several different land-uses, which is believed to be the primary generator of these accidents. The goal of this project is to determine the primary causes of these accidents and determine potential countermeasures to reduce the crash rate for …

Applying Performance Engineered Mixture Design To Permeable Concrete, Rachel Pohl

Civil Engineering Undergraduate Honors Theses

The scope of research and application related to permeable pavements has recently broadened. The desire to significantly reduce the environmental impact of large paved areas makes the permeable pavement concept more desirable (American Concrete Institute, 2018). Although research and interest are increasing, the actual application of permeable pavement is still very limited and has not reached the airfield arena. In airfields, permeable pavement could possibly be used for aircraft aprons - which currently require substantial measures to control stormwater runoff. Permeable pavements are typically used in low-traffic-volume / lightly loaded applications; questions remain regarding a permeable pavement’s ability to hold …

Efficiency Analysis Of Harvesting Solar Energy To Perform Mechanical Work, Haden S. Bragg

Undergraduate Theses and Capstone Projects

The majority of the world’s electricity is generated using fossil fuels; in fact, the United States Energy Information Administration (EIA) states that the U.S. used fossil fuels to generate 62.7 % of its electricity in 2019 [1]. The goal of this research was to create a system that could perform mechanical work using only renewable resources. We built a solar charging station that uses two solar panels to generate electricity and an electric bicycle whose battery can be charged using the charging station. The efficiency for the type of solar cell used in this project is well established. Therefore, in …

Dose Response Effect Of Mycobacterium Smegmatis-Derived Lipomannan In Raw 264.7 Murine Macrophages, Cassandra Robertson

Undergraduate Theses and Capstone Projects

Tuberculosis is a debilitating respiratory disease caused by the bacterial species Mycobacterium tuberculosis, which acts by infecting the host’s macrophages and evading their immune responses. The purpose of the study was to determine if RAW 264.7 murine macrophage activity could be facilitated and intensified by stimulation with LAM from M. smegmatis. Stimulation with bacterial LAM, and lipopolysaccharide (LPS) as a positive control, yields functional endpoints: nitric oxide (NO) production measured by nitrites (NO2) in the culture supernatant and expression of proteins, such as tumor necrosis factor-α and inducible nitric oxide synthase (iNOS). RAW 264.7 cells were stimulated dose-responsively with LAM …

Developing An Enhanced Adaptive Antenna Beamforming Algorithm For Telecommunication Applications, Mohammad Omar Tawfiq Abualhayja'a

Electrical Engineering Theses

As a key enabler for advanced wireless communication technologies, smart antennas have become an intense field of study. Smart antennas use adaptive beamforming algorithms which allow the antenna system to search for specific signals even in a background of noise and interference. Beamforming is a signal processing technique used to shape the antenna array pattern according to prescribed criteria.

In this thesis, a comparative study is presented for various adaptive antenna beamforming algorithms. Least mean square (LMS), normalized least mean square (NLMS), recursive least square (RLS), and sample matrix inversion (SMI) algorithms are studied and analyzed. The study also considers …

Evaluation Of Tracing Techniques In The Rat Spinal Cord Using A Custom Matlab Application., Rachel M. Zalla

Electronic Theses and Dissertations

The objective of this research project is to evaluate the efficiency of traditional chemical tracing compared to dual-viral tracing for labeling long ascending propriospinal neurons (LAPNs) in the uninjured rat spinal cord, and to develop a MATLAB program which will accurately quantify this labeling.

To evaluate chemical tracing, Fluoro-Ruby (FR) was injected at the level of the axon terminals, and the number of ipsilateral labeled cell bodies at lumbar level was quantified. Similarly, two dual-viral systems were evaluated, by either injecting retro-AAV-Cre or HiRet-Lenti-Cre unilaterally in combination with a Cre-dependent adeno-associated virus. The HiRet-Lenti and FR groups labeled significantly greater …

Determining The Efficacy Of Additive Manufacturing For The Aerospace Spare Parts Supply Chain, Kyle O'Brien

Electronic Theses and Dissertations

This thesis investigates how additive manufacturing (AM) based on-demand part production can supplement or replace the traditional production and inventory in typical aerospace’s spare parts supply chain systems. This study focuses on the operational characteristics of AM and its impacts on the overall logistics of plant-level operations. To capture the microscopic operational aspects of the AM production, a discrete-event simulation based approach was adopted, with key AM operation resources (e.g. AM system, operator) and attributes (e.g. AM manufacturing speed, individual part characteristics and demands) accounted for in the modeling process. In addition, a benchmark warehouse inventory model was also established …

Microrobots For Wafer Scale Microfactory: Design Fabrication Integration And Control., Ruoshi Zhang

Electronic Theses and Dissertations

Future assembly technologies will involve higher automation levels, in order to satisfy increased micro scale or nano scale precision requirements. Traditionally, assembly using a top-down robotic approach has been well-studied and applied to micro-electronics and MEMS industries, but less so in nanotechnology. With the bloom of nanotechnology ever since the 1990s, newly designed products with new materials, coatings and nanoparticles are gradually entering everyone’s life, while the industry has grown into a billion-dollar volume worldwide. Traditionally, nanotechnology products are assembled using bottom-up methods, such as self-assembly, rather than with top-down robotic assembly. This is due to considerations of volume handling …

Susceptibility Assessment Of Bank And Floodplain Erosion In Stream Restoration Using A Two-Dimensional Hydrodynamic., Fereshteh Noorbakhsh

Electronic Theses and Dissertations

In the design of stream restorations, boundary shear stress (shear stress) and velocity during high flow events are the key parameters in the assessment of the risk of morphological failure associated with channel bank and bed erosion and sediment transport. The use of two-dimensional hydrodynamic models (2D Models) is becoming more common to estimate critical shear stress and velocity for stream restoration projects. These models can give detailed distribution of shear stress and velocity over floodplain surfaces and channel. Obtaining reliable and correct estimates of stress and velocity require an accurate digital terrain model, estimates of input flows at the …

Experimental Evaluation Of Heat Leak And Convective Heat Transfer In A Household Freezer., Catherine E. Berghuis

Electronic Theses and Dissertations

Heat leak into household refrigerated cabinets is a key driver affecting energy consumption and efficiency of the cooling system. Additionally, knowledge of heat transfer coefficients of internal surfaces is valuable in the development of cabinet and system level performance simulations. Several studies have examined heat leak of refrigeration units using heat flux sensors (HFS); however, no such studies have used heat flux measurements to derive convective heat transfer coefficients of the refrigerated unit walls. The goal of this study is to evaluate the use of HFS to quantify heat leak into a 490-liter freezer and determine the wall convective heat …

Experimental And Numerical Study Of Process Parameters Effects Towards Part Quality And Porosity During Powder Bed Additive Manufacturing Processes., Subin Shrestha

Electronic Theses and Dissertations

Powder bed additive manufacturing (PB-AM) process utilizes an electron beam or a laser as a heat source to melt the metallic powder particles. These processes have the capability of freeform fabrication, however certain defects such as porosity, high surface roughness, etc. would hinder its application. It is important to understand the effect of the process parameters and the underlying physical phenomena, which lead to the formation of such defects. In this regard, a three-dimensional (3D) thermo-fluid model is developed to study the effect of beam speed on the surface morphology during powder bed electron beam additive fabrication (PB-EBAF). Besides, the …

A Method For Uncertainty Managementin Life Cycle Assessment Studies –A Tiered-Hybrid Case Study Of An Irish Construction Project, Deidre Wolff

Doctoral

Life Cycle Assessment (LCA) quantifies the potential environmental impact of a product system throughout its life cycle from raw material extraction, production, manufacture, use and maintenance through to final disposal. The results from LCA studies are often used to support decision-making processes andpolicy development. LCA is conducted in four iterative steps, beingGoal and Scope definition, Life Cycle InventoryAnalysis (LCI), Life Cycle Impact Assessment (LCIA), andInterpretation. The guidelines for each step are provided in the International Organization for Standardization (ISO) standards, ISO 14040:2006 and 14044:2006. Uncertainty arises in all steps of an LCA,yet the propagation and reporting of these uncertainties is …

Design Of Submicron Structured Guided-Mode-Resonance Near-Infrared Polarizer, Marzia Zaman

Graduate Theses and Dissertations

The objective of this research is to design a larger submicron linear polarizer in the near-infrared wavelength range with a wide bandwidth which can be fabricated using the conventional thin-film microfabrication technology to reduce cost. For this purpose, a gold (Au) wire-grid transmission-type transverse-magnetic (TM) polarizer and a silicon (Si) wire-grid reflection-type TM polarizer, were designed using the guided-mode-resonance filter. The Au wire-grid TM polarizer of 700nm grating width and 1200nm grating period has 95% transmittance at 2400nm, more than 1000nm resonance peak bandwidth, and an extinction ratio (ER) of around 300 with a moderated level of sidebands. The 700nm …

Area Efficient Device Optimization For Esd Protection In High Speed Interface Ics, Dan Thomas Jarard

Graduate Theses and Dissertations

Electrostatic discharge (ESD) protection is considered as a vital step in integrated circuit (IC) manufacturing process. IC chips are unable to overcome the effects of transient events without adequate discharge protection. Recent trend in the industry has seen the incorporation of system level ESD protection within the IC chip. Incorporating system level on-chip ESD protection often increases cost, degrades circuit performance and consumes layout area which could otherwise be used for improving the circuit performance. These design challenges could be easily overcome if the parasitic components in a circuit were used for ESD protection. Despite the various design challenges, on-chip …

An Fpga-Based Hardware Accelerator For The Digital Image Correlation Engine, Keaten Stokke

Graduate Theses and Dissertations

The work presented in this thesis was aimed at the development of a hardware accelerator for the Digital Image Correlation engine (DICe) and compare two methods of data access, USB and Ethernet. The original DICe software package was created by Sandia National Laboratories and is written in C++. The software runs on any typical workstation PC and performs image correlation on available frame data produced by a camera. When DICe is introduced to a high volume of frames, the correlation time is on the order of days. The time to process and analyze data with DICe becomes a concern when …

Cfd Modeling Of Vertical Axis Wind Turbine Arrays Using Actuator Cylinder Theory, Cory Schovanec

McKelvey School of Engineering Graduate Student Theses & Dissertations

The goal of this thesis is to analyze the flow field and power generation from a vertical axis wind turbine (VAWT) by extending the Actuator Cylinder Model to include the viscous effects. Turbulent flow effects in the Actuator Cylinder Model are modeled by solving the Reynolds-Averaged Navier-Stokes (RANS) equations with the Spalart-Allmaras (SA) turbulence model in ANSYS FLUENT. A study is performed to establish mesh independence of the solutions. Numerical solutions on a fine mesh are compared to existing theoretical results based on inviscid theory for a series of flow conditions and turbine sizes. Similar trends in the present turbulent …

A New Spatially-Resolved Method To Sample Biofilms From Drinking Water Fountains, Yi Liu

McKelvey School of Engineering Graduate Student Theses & Dissertations

A drinking fountain, also called a water fountain, is a facility designed to provide drinking water in public space. It consists of a basin and a spout. The users need to bend down to the stream to collect or drink water. The history of water fountains can be traced back to ancient Rome. Even before potable water was provided to individual homes, water for drinking was already made available to citizens through access to public fountains. Nowadays, drinking water fountains usually exist in public places, like schools, hospitals, and libraries. Many jurisdictions in the United States require drinking fountains to …

Peptoid And Antibody-Based Gfp Sensors, Solomon Isu

Graduate Theses and Dissertations

In this work, we have made and characterized a pair of immunobiosensors for detecting the green fluorescent protein (GFP) in an aqueous matrix. An anti-GFP antibody-based biosensor was assembled to detect GFP, while a novel peptoid (N-substituted oligomers of glycine designated as IOS-1) biosensor was also assembled for GFP detection. A quartz crystal microbalance (QCM) gold sensor was used as the supporting substrate for self-assembly of the immunobiosensors. Gravimetric measurements of the QCM gold sensor during immunobiosensor construction and operation were available in real-time using a QCM instrument. X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, and Fluorescence microscopy were used …

Design And Demonstration Of Automated Technologies For The Fabrication And Testing Of Pem Fuel Cell Systems, Vladimir Gurau, Daniel Cox, Devin C. Fowler, Matthew Carter, Adedayo Ogunleke

Manufacturing Engineering: Faculty Publications (2015-2023)

This paper describes the research efforts at Georgia Southern University to develop robotic technologies for the fabrication of fuel cell components and stacks, as well as the design and fabrication of a High Temperature Proton Exchange Membrane Fuel Cell (HT-PEMFC) power system to be used as motive power and auxiliary power unit (APU) for a long range, unmanned, fully autonomous forest rover. The paper describes a manufacturing workcell consisting of a Yaskawa Motoman SDA5F dual arm robot with machine vision used for sorting, reorientation and stacking fuel cell components in presenters in preparation for their subsequent robotic assembly in fuel …

Thiol-Induced Degradation Of Hydrogels Utilizing Multiresponsive Dithiomaleimides Crosslinkers, Kundu Thapa

Honors Theses

Hydrogels are hydrophilic, three-dimensional materials used as platforms for various biomedical applications such as drug delivery, biosensors, or as scaffolds in tissue engineering. The ability to degrade on demand in response to biological cues is particularly attractive whether dealing with microgels or if one aims to release an active ingredient from a scaffolding material. For instance, many cancer-remediation drug delivery platforms leverage the high concentration of glutathione, a thiol-containing tripeptide, found in cancerous cells. In this work, poly(ethylene glycol) acrylate hydrogels were fabricated using dithiomaleimide (DTM) moieties. DTMs are known to undergo thiol-exchange reactions favoring the dissolution of the hydrogel …

Monolithic Chalcogenide Optical Nanocomposites Enable Infrared System Innovation: Gradient Refractive Index Optics, Myungkoo Kang, Laura Sisken, Charmayne Lonergan, Andrew Buff, Anupama Yadav, Claudia Goncalves, Cesar Blanco, Peter Wachtel, J. David Musgraves, Alexej V. Pogrebnyakov, Erwan Baleine, Clara Rivero-Baleine, Theresa S. Mayer, Carlo G. Pantano, Kathleen A. Richardson

Materials Science and Engineering Faculty Research & Creative Works

The size and weight of conventional imaging systems is defined by costly non-planar lenses and the complex lens assemblies required to minimize optical aberrations. The ability to engineer gradient refractive index (GRIN) optics has the potential to overcome constraints of traditional homogeneous lenses by reducing the number of components in optical systems. Here, an innovative strategy to realize this goal based on monolithic GRIN media created in Ge-As-Se-Pb chalcogenide infrared nanocomposites is presented. A gradient heat treatment to spatially modulate the volume fraction of high refractive index Pb-rich nanocrystals within a glass matrix is utilized, providing a GRIN profile while …

Effect Of Socioeconomic Factors On Crash Occurrence, Nikiforos Stamatiadis, Shraddha Sagar, Samantha Wright, Aaron Berry Cambron

Kentucky Transportation Center Research Report

Road traffic crashes are a leading cause of death in the United States. In Kentucky, per capita crash rates and crash-related fatalities have outpaced the national average for over a decade. Wanting to explain why the U.S. Southeast sees higher crash rates than other regions, researchers have argued the region’s unique socioeconomic conditions provide a compelling explanation. Taking this observation as a starting point, this study examined the relationship between highway safety and socioeconomic characteristics using an extensive crash dataset from Kentucky. This research sought to identify at-risk drivers based on the socioeconomic and demographic attributes of the zip codes …

Investigation Of Driver License Issuance Alternatives, Steven Andrew Martin, Abraham Najarzadeh, Jennifer R. Walton

Kentucky Transportation Center Research Report

This study develops an alternative model for issuing driver licenses and personal identifications in Kentucky. Under the current model, most licenses are distributed by circuit court clerks at 142 offices across the state while the Kentucky Transportation Cabinet (KYTC) provides central and regional support for specific license types. Given the cumbersome administrative structure and impending REAL ID requirements, both circuit clerks and KYTC administrators would like to explore an alternative distribution model. Researchers at the Kentucky Transportation Center (KTC) projected the costs of transitioning from the current issuance model to a centralized DMV model where licenses are distributed at 18 …

Pollution Prevention And Water Reuse At Utah Department Of Transportation Facilities, Amanda Stoudt

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

As stormwater flows over roads, sidewalks, and other impervious surfaces, it picks up pollutants that are deposited on these surfaces. One common pollutant transported by stormwater is road salt. While the application of road salt is crucial for wintertime public safety, road salt has a host of negative environmental impacts. Road salt has been linked to increasing levels of dissolved solids in groundwater, vegetation damage, and behavioral changes in aquatic organisms. Studies have shown that these impacts are concentrated around salt storage facilities. As a result, the United States Environmental Protection Agency issued many state departments of transportation municipal separate …