Engineering Commons^™

Development Of A Matlab Gui To Assist The Active Comprehension Of Biomedical Transport Phenomena Using A Visual Aid, Pranav Suri

Biomedical Engineering Undergraduate Honors Theses

Studies show that inductive teaching methods for Biomedical Transport Phenomena greatly benefit from an accompanying visual aid. The following project aimed to develop a MATLAB GUI application that illustrates steady-state heat transfer with a graph and heat map using user-defined boundary conditions and numerical parameters. The application was evaluated using a survey that first familiarized the user with the GUI by running through heat transfer exercises, then allowed the user to experiment with the application, and finally asked users about their experiences using a questionnaire. The responses indicate that the GUI was received positively overall, and that a MATLAB component …

Maximizing The Academic And Professional Success Of First-Generation College Students In Biomedical Engineering, Mona Ahmed

Biomedical Engineering Undergraduate Honors Theses

Although efforts to increase the inclusion, retention, and success of first-generation college students (FGCSs) in research universities have resulted in noticeable progress, FGCSs still feel academically challenged, isolated, and show more anxiety and depression compared to non-FGCSs. Moreover, FGCSs may possess additional underrepresented identities that exacerbates the problem. There is more risk of dropping out of academic programs for FGCSs enrolling in STEM degrees, especially those of more multidisciplinary nature such as Biomedical Engineering. From the overall population of the State of Arkansas, only 23.3% have a bachelor’s degree or higher which is the third least percentage in the United …

Differential Patterns Of Theta Activation Underlying Various Cognitive Control Strategies, Jarrod Eisma

Biomedical Engineering Undergraduate Honors Theses

In this study, EEG was recorded from 157 participants at the University of Arkansas as they performed three computer tasks that tested inhibitory control (Go/Nogo Task), proactive and reactive control (AX-Continuous Performance Task), and resolving response conflict (Global/Local Task- modified Flanker Task). Time-frequency analysis (ERSP) was the primary focus of this study, in order to take advantage of the temporal and frequential characteristics of EEG recordings. The ERSPs and following statistical analysis showed significantly higher midfrontal theta band (4-8 Hz) power values for target trials (those that required more cognitive control) than control trials, which indicated that the procedure was …

Computational Analysis Of A New Planar Mixing Layer Flame Configuration To Study Soot Inception, Carmen Ciardiello

Honors Scholar Theses

The production of soot is omnipresent in society today. Soot is the product of many of the combustion processes that provide the bulk of the usable energy throughout the world. Furthermore, soot particulate poses a great danger to both the environment and all forms of life on Earth. It has proven to pollute ecosystems, foster health problems for human beings, and degrade air quality [1].

These dangers make studying and understanding soot particulate paramount for improving the quality of life. Thus, this study introduces a new flame configuration for studying soot inception. Presently, various common flame configurations have been found …

Thermodynamic Potential Of Very High Performance Fuel Cells, Kimberly Liang

Honors Scholar Theses

Fuel Cells are devices that use the chemical energy of a fuel (e.g. hydrogen) to electrochemically produce electricity. Similar to a conventual combustion engine, a fuel cell will continue to run and generate electricity as long as fuel is supplied. However, unlike a conventional combustion engine, fuel cells have a much higher theoretical efficiency and do not directly emit harmful air pollutants. This project will focus on a fuel cell that uses hydrogen as fuel and oxygen as an oxidizing agent.

As fuel cell technology evolved, high pressure fuel cell systems became of interest in portable applications, such as submarine …

Quantifying Air Pollution At The Stamford Transportation Center, Brianna Mancuso, Kristina Wagstrom

Honors Scholar Theses

There is a need to analyze particulate matter concentrations at the Stamford Transportation Center according to the Western Connecticut Coalition of Governments. Stamford has recently undergone rapid urbanization and large scale construction resulting in traffic congestion. Congested traffic areas in urban centers are key contributors to poor air quality. Therefore, there is a need to analyze the pollution concentrations at the bus stops near the station. Every day, hundreds of shuttles and cars idle around the Transportation Center. Thousands of passengers wait at nearby bus stops every day and can potentially be exposed to high amounts of vehicle produced pollution …

An Assessment Of Renewable Energy Technology Implementation In Storrs, Connecticut: Emissions Reduction And Feasibility Of A Microgrid System At Uconn, Sophie Macdonald

Honors Scholar Theses

The purpose of this project is to design a clean energy-sourced microgrid for UConn’s main campus that would reduce the university’s energy emissions while remaining within the geographic boundaries of viable UConn-owned land. Economic cost was not considered in this analysis; instead, emissions and space constraints were the optimized measures of value and feasibility. Sources of energy that were considered include photovoltaics (PV), wind turbines, hydrokinetic systems, and fuel cells. Energy storage capacity was included in the analysis as well. The overall system was optimized first by ignoring space constraints and for a minimum of 10% reduction from the current …

Evaluating The Effects Of Muscle Force Production Strategies And Anterior Cruciate Ligament Forces (Strain) On Gait Patterns During Running, Amanda Astrologo

Honors Scholar Theses

Anterior cruciate ligament (ACL) injuries are among the most common injuries experienced by athletes in the United States. Even after reconstruction surgery individuals have been known to develop complications much later in life, including long-term or permanent alterations to their gait, which may lead to early-onset knee osteoarthritis. This thesis work sought to define these alterations as they pertain specifically to running. Using results and parameters from previous studies, the goal of this study is to compare muscle force production strategies, as they relate to ACL force and strain, of injured and non-injured individuals. These values, muscle forces and ACL …

Effects Of Normobaric Hypoxia On Oculomotor Dynamics Of Aviator Students During A Simulated Flight Task, Carl Wesley Rider, Abby Mccarty, Anna Blackley, Austin Deshner, Josh Engberg, Kaela Ehrlich, Theodore Hu, Maja Jankovic, Moroni De Moors, Jared Hornsby, Mitchell Morrison, Brian Walsh

Masters Theses

Hypoxia occurs when the body's tissues are unable to obtain adequate oxygen supply and is the primary environmental factor present when pilots are exposed to increasing altitude levels. Hypoxia leads to impaired vision, cognition, and motor control function, which can negatively affect performance and become deadly if a pilot becomes incapacitated. Thus, objective identification of early-onset hypoxia is critical to increase the time of useful consciousness and prevent physiological episodes. Of the few studies utilizing eye-tracking, there is disagreement and mixed results concerning saccadic eye metrics as a means to measure and detect hypoxia. Therefore, the purpose of this study …

Development Of Vegetable Oil Based Nano-Lubricants, Vicente Cortes

Theses and Dissertations

Nowadays, the depletion of crude oil reserves in the world and the global concern in protecting the environment from contamination have renewed interest in developing environment friendly lubricants derived from alternative sources such as vegetable oils. Mineral oil is the most common lubricant, however, it also has poor biodegradable properties. Vegetable oils exhibit good viscosity index, flash point, pour point, tribological properties, and are biodegradable. Furthermore, the use of nanoparticles as additives has shown to improve anti wear and anti-friction properties of the base lubricant. The present research project will evaluate experimentally the rheological and tribological behavior of coconut oil, …

Processing And Microstructural Characterization Of Silicon Carbide, Silicon Nitride, And Tungsten Carbide Fibers, Christian Garcia

Theses and Dissertations

This research focuses on developing polymer-derived ceramic fibers. The spun micro/nanofibers were sintered into silicon carbide/silicon nitride and tungsten carbide respectively. The relationship between processing, fiber microstructure, morphology, and purity is investigated by scanning electron microscopy, Fourier transform infrared spectroscopy, energy-dispersive X-ray spectroscopy, and thermogravimetric analysis. Dynamic Mechanical Analysis was used to test the reinforcement capabilities of tungsten carbide fibers. EDS identified a near-perfect 1:1 Si-C ratio in silicon carbide fibers sintered between 1200 °C -1400 °C, Silicon carbide was confirmed by FTIR between 1000 °C – 1400 °C. Silicon Nitride peaks were noted in FTIR between 1200 °C – …

Cyber Security Evaluation Of Smart Electric Meters, Harsh Kumar

Theses and Dissertations

In this thesis, effect of intermediate network systems on power usage data collection from Smart Electric Meter in Smart Grid was evaluated. Security integrity of remote data collection from GE’s Power Quality Smart Electric Meter EPM 6100 and EPM 7000 under cyber-attacks were evaluated. Experimental security evaluations of Smart Electric Meters were conducted to understand their operation under cyber-attacks. Integrity of data communication between the GE’s smart meters and remote monitoring computer was evaluated under different types of cyber security attacks. Performance comparison was done for security integrity of EPM 6100 and EPM 7000 power quality meter under various cyber-attacks.

Electrical And Chemical Characterization Of A Helium-Air Non-Thermal Atmospheric Pressure Plasma Jet, Adam Zandani

Seton Hall University Dissertations and Theses (ETDs)

Plasma is one of the most complicated, yet promising fields in physics due to its high efficiency and multitude of crucial applications such as biological sterilization, polymer modification, surface treatments, etching, agriculture, and facilitation of selective catalytic processes to name a few. With these advantages, mysteries still remain. With this in mind, in order to accurately gauge the total influence of the plasma applied in various processes, understanding what is being produced and how the production occurs is vital. To understand this, optical emission spectroscopy was used to gauge how the species generated are influenced by operation parameters such as …

Chlorine Removal From U.S. Solid Waste Blends Through Torrefaction, Zhuo Xu, Josh W. Albrecht, Shreyas Kolapkar, Stas Zinchik, Ezra Bar Ziv

Michigan Tech Publications, Part 1

The amount of solid waste generated annually is increasing around the world. Although the waste has a high calorific value, one major obstacle that may prevent it from becoming a feedstock for power applications is the existence of polyvinyl chloride (PVC), which causes corrosion and emission issues after combustion due to its high chlorine content. Torrefaction is known to release hydrochloric acid; thus, it has been applied in this study for the reduction of chlorine from potential waste feedstocks. Fiber-plastic (60-40%) waste blends, with different chlorine content levels, as well as PVC were used in the current study. Torrefaction was …

Revised Lewis Bending Stress Capacity Model, Edward E. Osakue

Faculty Publications

Background: During operation, cylindrical gearset experiences tangential, radial, and axial (helical gears only) force components that induce bending, compressive, and shear stresses at the root area of the gear tooth. Accurate estimation of the effective bending stress at the gear root is a challenge. Lewis was the first person who attempted estimating the root bending stress of spur gears with some reasonable accuracy. Various gear standards and codes in use today are modifications and improvements of the Lewis model.

Objective: This research aims at revising the Lewis model by making adjustments for dynamic loads, shear stresses, axial bending stress for …

2020 Spring Graduate Recognition Program, Propulsion Research Center, Robert Frederick

PRC Graduate Recognition

This program includes the graduate recognition program for spring 2020. Includes photographs, upcoming events, recent publications, and student profiles.

Towards A High Bias Voltage Mems Filter Using Electrostatic Levitation, Mark Pallay, Ronald Miles, Shahrzad Towfighian

Mechanical Engineering Faculty Scholarship

Traditional MEMS filters use a comb drive structure that suffers from the pull- in instability, which places a significant limitation on the achievable signal-to- noise ration of the sensor. Because the output signal from a capacitive sensor

is linearly related to the applied voltage, it is desirable to use a capacitive sensor that can withstand large voltages upwards of 100V. However, the pull-in instability causes high voltages to destroy the device and a trade-off between performance and reliability must be made. Electrostatic levitation, which works by pulling electrodes apart instead of together, eliminates the pull-in instability and allows for very …

Development Of Fully Balanced Ssfp And Computer Vision Applications For Mri-Assisted Radiosurgery (Mars), Jeremiah Sanders

Dissertations and Theses (Open Access)

Prostate cancer is the second most common cancer in men and the second-leading cause of cancer death in men. Brachytherapy is a highly effective treatment option for prostate cancer, and is the most cost-effective initial treatment among all other therapeutic options for low to intermediate risk patients of prostate cancer. In low-dose-rate (LDR) brachytherapy, verifying the location of the radioactive seeds within the prostate and in relation to critical normal structures after seed implantation is essential to ensuring positive treatment outcomes.

One current gap in knowledge is how to simultaneously image the prostate, surrounding anatomy, and radioactive seeds within the …

Comparison Of Locational Beamforming Algorithms For Audio Targeting, Thomas Lewis Bradshaw

Undergraduate Honors Capstone Projects

In many applications it is desirable to focus on the direction a signal is coming from to isolate the signal from interfering noise coming from other directions. This is often done by focusing the receiver on a given direction. One method to accomplish this focusing is to use an array of receivers and a signal processing algorithm called beamforming. This algorithm attenuates signals coming from all other directions besides the direction of interest, which can be viewed pictorially as a beam. However, it would also benefit many applications to be able to focus on a location rather than just a …

Characterization Of Rhodopseudomonas Palustris Strains For The Production Of Fixed Nitrogen Fertilizer For Mars, Andrew James Walters

Undergraduate Honors Capstone Projects

The purpose of this project was to characterize the potential of various strains of purple non-sulfur bacteria for the production of fixed nitrogen fertilizers for the manned Mars missions. Six strains of Rhodopseudomonas palustris (CGA009, CGA010, TIE-1, NifA*, and PB23) were all investigated. Through initial growth trial experiments, R. palustris NifA* and PB23 were selected for their engineered nitrogen fixation and rapid growth respectively. Growth curves and ammonium concentrations were collected over time in pilot scale batch photobioreactors (200 mL). Biomass production was then scaled up to benchtop photobioreactors (1.5 L). Fourteen liters of both NifA* and PB23 were then …

Study Of The Detection And The Emission Of Thz Waves In Mos₂Material, Ayah Masoud Ass’Ad Hijazi

Electrical Engineering Theses

Terahertz (THz) technology is receiving a wide interest nowadays, developing more researches worldwide to emerge new devices based on the THz regime and overcoming the challenge of the remarkable THz-gap. This thesis is concerned with studying and developing new emerging materials with new structures in terms of THz waves. The main objective of this thesis is to examine how the MoS₂ material in nanoribbons structure detect and emit THz waves theoretically and experimentally in contrast to Graphene nanoribbon material. The theoretical model was used alongside the experimental setup to fully understand the behavior of the materials and to have a …

Brief Survey And Testbed Development For Blockchain Based Internet Of Things, Aishwant Ghimire

Honors Theses

Blockchain and the Internet of Things are uprising in today’s technology world. Internet of Things or IoT are the devices with unique identifiers that share data or information over the internet whereas, Blockchain is a peer to peer network with a distributed ledger that contains a list of blocks that are linked together by cryptography. Fascinated and motivated by blockchain and Internet of Things (IoT), this thesis provides a review on blockchain based internet of things and also introduces a working testbed that integrates the two together. It also uses IoT device to invoke transactions into the blockchain. The reasons …

Solution To Exide Technologies Inbatec Inefficiency, Spencer Christian, Shixuan Hou, Mary Fairley, Reagan Gilker, Covenson Latouche

Chemical Engineering Undergraduate Honors Theses

The inefficiency of the battery charging time in Inbatec Units 1 and 2 in the Exide Technologies Fort Smith was initially investigated by a student team in Fall 2019, and the investigation was continued into Spring 2020. The Exide Technologies facility in Fort Smith, Arkansas utilizes 13 Inbatec units to charge the lead-acid batteries. The Inbatec systems circulate the sulfuric acid solution through a cooling tower to maintain to optimal charging temperature. Previous analysis of the charging process for Inbatec Units 1 and 2 show the cooling tower have the capacity to quickly remove the excess heat in the sulfuric …

Removal Of Fluoride From Mine Water Via Adsorption For Land-Applied Soil Amendment, Jacqueline Payne, Mary Johnson, Kevin Le, Michelle Dopp, Courtney Golman, Adrian Damian, Ethan Phan

Chemical Engineering Undergraduate Honors Theses

The process of mining minerals and elements from ores and rocks creates acid rock drainage (ARD). This drainage is water that contains heavy metals and minerals that can be dangerous for human consumption or damaging to the environment. The mining industry has employed various water treatment methods to prevent these metals and minerals from being discharged into water sources such as ponds, lakes, and streams. Currently, the most used treatment process in the mining industry is a cost-effective highdensity sludge (HDS) process. This method reduces the concentration of metals and elements with the use of lime/limestone. However, the concentration of …

Removal Of Fluoride From Mine Water Via Adsorption For Land-Applied Soil Amendment, Ethan Phan, Adrian Damian, Kevin Le, Mary Johnson, Courtney Golman, Michelle Dopp, Jacqueline Payne

Chemical Engineering Undergraduate Honors Theses

The process of mining minerals and elements from ores and rocks creates acid rock drainage (ARD). This drainage is water that contains heavy metals and minerals that can be dangerous for human consumption or damaging to the environment. The mining industry has employed various water treatment methods to prevent these metals and minerals from being discharged into water sources such as ponds, lakes, and streams. Currently, the most used treatment process in the mining industry is a cost-effective high-density sludge (HDS) process. This method reduces the concentration of metals and elements with the use of lime/limestone. However, the concentration of …

Scale-Up Of Polyaniline Cellulose Membranes, Isaac Bodemann

Chemical Engineering Undergraduate Honors Theses

Polyaniline coated cellulose membranes show impressive conductive properties that may be used to innovate traditional charged separation techniques, such as electrodeionization. However, these membranes are not sold to consumers, so they cannot be easily integrated into such systems. This research focuses on the scale-up and development of positively charged anion exchange membranes to be used in EDI cells. Novel cellulose membranes were made using lab-specific cellulose. These membranes were then coated using a polyaniline technique adopted from a paper titled, “Flexible Electrically Conductive Nanocomposite Membrane Based on Bacterial Cellulose and Polyaniline." This paper details the methods used to add the …

Solution To Exide Technologies Inbatec Inefficiency, Reagan Gilker, Mary Fairley, Spencer Christain, Shixuan Hou, Covenson Latouche

Chemical Engineering Undergraduate Honors Theses

The inefficiency of the battery charging time in Inbatec Units 1 and 2 in the Exide Technologies Fort Smith was initially investigated by a student team in Fall 2019, and the investigation was continued into Spring 2020. The Exide Technologies facility in Fort Smith, Arkansas utilizes 13 Inbatec units to charge the lead-acid batteries.

The Inbatec systems circulate the sulfuric acid solution through a cooling tower to maintain to optimal charging temperature. Previous analysis of the charging process for Inbatec Units 1 and 2 show the cooling tower have the capacity to quickly remove the excess heat in the sulfuric …

Improving Pv Module Efficiency Through Cooling, Ashley Cox

Chemical Engineering Undergraduate Honors Theses

The Solarbacks researched and designed a variety of cooling methods that could be used to improve the efficiency of photovoltaics. These cooling methods can be separated into two categories: active and passive methods. The active cooling method of hydraulic cooling and the passive cooling methods of heat sinks (fins), optical coatings, thermosyphons, phase change materials, and thermoelectric generators were all taken into consideration as potential cooling methods. Passive cooling methods were preferred because the use of electricity required for the cooling mechanism would reduce the net electricity and subsequent profit from the panels.

Two variations of hydraulic cooling were researched: …

Removal Of Fluoride From Mine Water Via Adsorption For Land-Applied Soil Amendment, Adrian Damian, Kevin Le, Mary Johnson, Ethan Phan, Courtney Golman, Michelle Dopp, Jacqueline Payne

Chemical Engineering Undergraduate Honors Theses

The process of mining minerals and elements from ores and rocks creates acid rock drainage (ARD). This drainage is water that contains heavy metals and minerals that can be dangerous for human consumption or damaging to the environment. The mining industry has employed various water treatment methods to prevent these metals and minerals from being discharged into water sources such as ponds, lakes, and streams. Currently, the most used treatment process in the mining industry is a cost-effective highdensity sludge (HDS) process. This method reduces the concentration of metals and elements with the use of lime/limestone. However, the concentration of …

Improving Pv Module Efficiency Through Cooling, Brandon Conrad, Blake Bradley, Ashley Cox, Donhy Mai, Harrison Dawson, Megan Reynolds, George Hill

Chemical Engineering Undergraduate Honors Theses

The Solarbacks researched and designed a variety of cooling methods that could be used to improve the efficiency of photovoltaics. These cooling methods can be separated into two categories: active and passive methods. The active cooling method of hydraulic cooling and the passive cooling methods of heat sinks (fins), optical coatings, thermosyphons, phase change materials, and thermoelectric generators were all taken into consideration as potential cooling methods. Passive cooling methods were preferred because the use of electricity required for the cooling mechanism would reduce the net electricity and subsequent profit from the panels.

Two variations of hydraulic cooling were researched: …