Engineering Commons^™

Experimental Validation Of Bulk-Graphene As A Thermoelectric Generator, Muhammad Uzair Khan, Amir Naveed, Syed Ehtisham Gillani, Dawar Awan, Muhammad Arif, Shaista Afridi, Muhammad Hamyun, Muhammad Asif, Saadia Tabassum, Muhammad Sadiq, Muhammad Lais, Muhammad Aslam, Saeed Ullah Jan, Zeeshan Ahad

Research outputs 2014 to 2021

Quest for alternate energy sources is the core of most of the research activities these days. No matter how small or large amount of energy can be produced by utilizing the non-conventional techniques and sources, every bit of innovation can reshape the future of energy. In this work, experimental analysis of the thermoelectric (TE) properties of bulk-graphene in the temperature range of (303 to 363) K is presented. Graphene powder was pressed to form a pellet which was used to fabricate the TE device. The effects of temperature on the Seebeck coefficient, electrical and thermal conductivities, and the dimensionless figure …

Deep Learning Control For Digital Feedback Systems: Improved Performance With Robustness Against Parameter Change, Nuha A. S. Alwan, Zahir M. Hussain

Research outputs 2014 to 2021

Training data for a deep learning (DL) neural network (NN) controller are obtained from the input and output signals of a conventional digital controller that is designed to provide the suitable control signal to a specified plant within a feedback digital control system. It is found that if the DL controller is sufficiently deep (four hidden layers), it can outperform the conventional controller in terms of settling time of the system output transient response to a unit-step reference signal. That is, the DL controller introduces a damping effect. Moreover, it does not need to be retrained to operate with a …

Effect Of Cutting Parameters And Tool Geometry On The Performance Analysis Of One-Shot Drilling Process Of Aa2024-T3, Muhammad Aamir, Khaled Giasin, Majid Tolouei-Rad, Israr Ud Din, Muhammad I. Hanif, Ugur Kuklu, Danil Y. Pimenov, Muhammad Ikhlaq

Research outputs 2014 to 2021

Drilling is an important machining process in various manufacturing industries. High-quality holes are possible with the proper selection of tools and cutting parameters. This study investigates the effect of spindle speed, feed rate, and drill diameter on the generated thrust force, the formation of chips, post-machining tool condition, and hole quality. The hole surface defects and the top and bottom edge conditions were also investigated using scan electron microscopy. The drilling tests were carried out on AA2024-T3 alloy under a dry drilling environment using 6 and 10 mm uncoated carbide tools. Analysis of Variance was employed to further evaluate the …

Impacts Of Traverse Speed And Material Thickness On Abrasive Waterjet Contour Cutting Of Austenitic Stainless Steel Aisi 304l, Jennifer Milaor Llanto, Majid Tolouei Rad, Ana Vafadar, Muhammad Aamir

Research outputs 2014 to 2021

Abrasive water jet machining is a proficient alternative for cutting difficult-to-machine materials with complex geometries, such as austenitic stainless steel 304L (AISI304L). However, due to differences in machining responses for varied material conditions, the abrasive waterjet machining experiences challenges including kerf geometric inaccuracy and low material removal rate. In this study, an abrasive waterjet machining is employed to perform contour cutting of different profiles to investigate the impacts of traverse speed and material thickness in achieving lower kerf taper angle and higher material removal rate. Based on experimental investigation, a trend of decreasing the level of traverse speed and material …

Hydrogen Adsorption On Sub-Bituminous Coal: Implications For Hydrogen Geo-Storage, Sefan Iglauer, Hussein Abid, Ahmed Z. Al-Yaseri, Alireza Keshavarz

Research outputs 2014 to 2021

Hydrogen is a clean fuel that can potentially revolutionize the energy supply chain and decarbonize fuel consumption. However, a key hurdle that needs to be overcome before a full-scale hydrogen economy can be established is hydrogen storage which is currently the main limitation. Here, we propose that hydrogen gas can be stored in underground coal seams, where it adsorbs on the coal surface. However, currently, no hard data related to such a procedure exists. We, therefore, demonstrate experimentally that significant amounts of hydrogen gas can be stored via this route. Hydrogen adsorption capacities reached 0.6 moles H₂/kg of …

A Fuzzy Clustering Methodology To Analyze Interfaces And Assess Integration Risks In Large-Scale Systems, Josh Henry Goldschmid

Doctoral Dissertations

“Interface analysis and integration risk assessment for a large-scale, complex system is a difficult systems engineering task, but critical to the success of engineering systems with extraordinary capabilities. When dealing with large-scale systems there is little time for data gathering and often the analysis can be overwhelmed by unknowns and sometimes important factors are not measurable because of the complexities of the interconnections within the system. This research examines the significance of interface analysis and management, identifies weaknesses in literature on risk assessment for a complex system, and exploits the benefits of soft computing approaches in the interface analysis in …

Infrastructure Systems Modeling Using Data Visualization And Trend Extraction, Jacob Marshal Hale

Doctoral Dissertations

“Current infrastructure systems modeling literature lacks frameworks that integrate data visualization and trend extraction needed for complex systems decision making and planning. Critical infrastructures such as transportation and energy systems contain interdependencies that cannot be properly characterized without considering data visualization and trend extraction.

This dissertation presents two case analyses to showcase the effectiveness and improvements that can be made using these techniques. Case one examines flood management and mitigation of disruption impacts using geospatial characteristics as part of data visualization. Case two incorporates trend analysis and sustainability assessment into energy portfolio transitions.

Four distinct contributions are made in this …

Scaling, Experiments, And Simulations Of Condensation Heat Transfer For Advanced Nuclear Reactors Safety, Palash Kumar Bhowmik

Doctoral Dissertations

“The purpose of this research was to perform scaled experiments and simulations to validate computational fluid dynamics (CFD) and empirical models of condensation heat transfer (CHT) for the passive containment cooling system (PCCS) of Small Modular Reactors (SMRs). SMRs are the futuristic candidates for clean, economic, and safe energy generation; however, reactor licensing requires safety system evaluations, such as PCCS. The knowledge in the reviewed relevant literature showed a gap in experimental data for scaling SMR’s safety systems and validating computational models. The previously available test data were inconsistent due to unscaled geometric and varying physics conditions. These inconsistencies lead …

Protection Of Modern Distribution Systems, Fahd Amin Hariri

Doctoral Dissertations

“Motivated by the potential for improvements in the electric distribution system’s protection schemes, this work examined the challenges facing protection schemes due to the integration of Distributed Generators (DGs). Traditional protection schemes for radial distribution systems were designed based on the unidirectional power flow from the source down to the loads. Protective devices typically use are overcurrent relays, autoreclosers, fuses, and circuit breakers. However, these protective schemes may no longer be sufficient to ensure correct operation in the new era of distribution systems integrated by DGs. This research investigated the impact of DGs that might mislead the protection schemes in …

Emi Characterization For Power Supplies And Machine Learning Based Modeling In Emc/Si, Jiayi He

Doctoral Dissertations

"Signal integrity (SI) and electromagnetic interference (EMI) are essential for consumer electronics and high-speed server applications. It is necessary to do EMI and SI modeling at the design stage. In this research, several modeling approaches for EMI and SI problems are proposed. By using measurement-based modeling method, the mechanism of conducted emissions (CE) on ac to dc power supplies in an LED TV is analyzed. A system-level transient simulation model is built to predict the conducted emission (CE). To characterize the equivalent dipole moment sources in RFI and EMI problems, a dipole source reconstruction method based on machine learning techniques …

Gis And Remote Sensing Groundwater Potentiality Investigation Of Gulu District, Uganda Using Synthetic Aperture Radar And Magnetic Geophysics, Rachel Ann Jones

Doctoral Dissertations

“Developing countries have few resources for ground-based hydrological investigations to determine optimal placement of boreholes for community water access. Remote sensing data are available at a variety of resolutions and sense different parameters, and are useful inputs for hydrologic models, but these data are rarely obtainable in developing countries with the parameters or resolutions necessary for hydrologic applications. This research seeks to use and improve existing remote sensing and GIS techniques to identify areas of optimal water supply in locations with limited geologic or hydrologic information, such as Gulu District, Uganda. Fusing different remotely sensed data sets can produce higher …

Contributions To The Performance Of Thin Film Capacitors For High Reliability Applications, Daniel Krueger

Doctoral Dissertations

"Capacitors are critical devices in microelectronic assemblies that must be incorporated into electronic systems through a variety of ways such as integrated or discrete devices. This work has developed new thin film capacitors deposited directly onto multichip module or printed circuit board surfaces to benefit from closer integration that enhances system performance for use in high reliability applications. The capacitors serve as filters or provide tuning and energy storage functions. Unexpected performance was observed during development that included low adhesion of the films to the substrates, higher effective dielectric constants than reported in literature, and low yields. Three publications resulted …

Studies On Protein Solubility, Ke Li

Doctoral Dissertations

"Solubility is a critical factor of protein-based drugs during processing and patient administration. This study focused on two aspects of solubility: one was the poly (ethylene) glycol (PEG) precipitation of monoclonal antibodies (mAbs) and another was crystallins aggregation that is associated with cataracts. Protein precipitation by PEG is a common technique for downstream processing. The effects of pH, ionic strength and the exclude volume effect on the protein precipitation by PEG were extensively studied, but the effects of glycosylation on protein precipitation by PEG has not been examined. Protein aggregation is not only a problem in downstream processing, but it …

Numerical And Experimental Study Of Mechanical Properties For Laser Metal Deposition (Lmd) Process Part, Lan Li

Doctoral Dissertations

"Laser Metal Deposition (LMD), also called as, Laser Engineered Net Shaping (LENS), Directed Energy Deposition (DED), is a typical Additive Manufacturing (AM) technology, is used for advanced free-form fabrication. It creates parts by directly melting materials and depositing them on the workpiece layer by layer. In this process, the metal powder or fiber is melted within the melting pool by laser beam or electron beam and quickly solidifies to the deposited layer. LMD technology shows great advantages over traditional manufacturing on complex structure fabrication, including high building rates, easy material replacement and reduced material waste. These merits make the wide …

Studies On Tornado-Structure Interactions And Guidance On Design Tornadic Wind Loading, Zhi Li

Doctoral Dissertations

“Tornadoes are violent natural hazards that could caused significant property loss and fatalities. Statistical data indicates that most fatalities during tornado incidents were caused by the building failure under tornadoes. For example, in the 2011 Joplin Tornado, 161 people were killed, and 84 percent of the fatalities were related to the failure of buildings. In addition, most of the significant, tornado-induced property loss and fatalities are relevant to the tornadoes passing through the densely populated regions. Besides buildings, bridges were also severely damaged or destroyed by tornadoes in the United States. To reduce the tornado-induced loss, it is imperative to …

Reveal Wind Loading Of Tornadoes And Hurricanes On Civil Structures Towards Hazard-Resistant Design, Ryan Honerkamp

Doctoral Dissertations

"Extreme winds impacting civil structures lead to death and destruction in all regions of the world. Specifically, tornadoes and hurricanes impact communities with severe devastation. On average, 1200 tornadoes occur in the United States every year. Tornadoes occur predominantly in the Central and Southeastern United States, accounting for an annual $1 billion in economic losses, 1500 injuries, and 90 deaths. The Joplin, MO Tornado in 2011 killed 161 people, injured more than 1000, destroyed more than 8000 structures, and caused $2.8 billion of property loss. Hurricanes occur predominantly on the United States East coast regions and along the coast of …

Effect Of Radiation Damage On Organic Phase Change Materials Thermal Storage Properties, Ryan Phillip Steere

Doctoral Dissertations

"This work discusses the effects of radiation damage on organic phase change materials for use in nuclear reactor containments and space craft. The effects of radiation on the latent heat of polyethylene wax (PEW) and a eutectic of methyl palmitate and lauric acid (EMPaLA) are evaluated. These PCMs were irradiated in three locations: the Missouri University of Science and Technology research reactor (MSTR), the University of Missouri research reactor (MURR) and cyclotron (MUC) up to a total dose of 2826, 2895 and 662 Gy, respectively. The samples irradiated at the MSTR showed latent heat changes up to 15.5% lower than …

Information-Based Methods And Models For Particle Flow Filtering, Kari Catherine Ward

Doctoral Dissertations

"Recursive estimation methodologies, such as Kalman and Bayesian filters, typically require models of some kind to perform the estimation. This filtering process seeks to improve knowledge surrounding some quantities of interest, or states, over time by incorporation of imperfect observations. The models required pertain to the state dynamics, sensors from which measurements are obtained, and probabilistic models of the underlying stochastic processes. In addition to any number of necessary models, real-world application of a filter is normally accompanied by at least one, if not several, techniques to promote better performance. These methods vary in purpose from expanding the kinds of …

Enhanced Heavy Oil Recovery By Low Salinity Polymer Flood Combined With Microgel Treatment, Yang Zhao

Doctoral Dissertations

“Heavy oil resources account for a large portion of the total oil reserves around the world. The target heavy oil reservoir is located on Alaska’s North Slope (ANS). Advantages of low-salinity HPAM polymer (LSP) over high-salinity polymer (HSP) were demonstrated. LSP could recover more oil with 40% less polymer consumption. No additional oil was recovered by HSP after LSP flood. The first-ever polymer flood pilot on ANS showed remarkable success regarding water cut reduction, oil production increase, delayed breakthrough, and projected oil recovery improvement. Polymer alone was insufficient to achieve satisfactory recovery as the reservoirs were highly heterogeneous. Microgels could …

Sensor Data Based Adaptive Models For Assembly Worker Training In Cyber Manufacturing, Md. Al-Amin

Doctoral Dissertations

“Production innovations are occurring faster than ever leading conventional production systems towards cyber manufacturing. Manufacturing workers thus need to frequently learn new methods and skills. In fast-changing, largely uncertain production systems, manufacturers with the ability to comprehend workers’ behavior and assess their operational performance in near real-time will achieve better performance than peers. Recognizing worker actions in near real-time while performing the assembly can serve this purpose. However, reliably recognizing the assembly actions performed by the workers is challenging, because the actions for assembly are complex and workers are not only heterogeneous but sensitive to the variation of the work …

Extracting Metallurgy Contaminants And Hydrocarbons Removing From Water And Industrial Wastewater Using Enhanced Emulsion Liquid Membrane With Nanoparticles And Ionic Liquid, Qusay Al-Obaidi

Doctoral Dissertations

It is an uphill battle to extract pollutants such as heavy metals, hydrocarbons, and radioactive metals from water and industrial wastewater. Emulsion liquid membrane (ELM) is an emerging technology that combines extraction/recover and stripping in one stage to extract/recover heavy metals and/or hydrocarbons from water and wastewater. ELM devised a way to clean up heavy metals and/or hydrocarbons from the water and wastewater where its primary chemicals can be recycled and reused.

In this work, the Emulsion Liquid Membrane (ELM) has been enhanced by adding nanoparticles and ionic liquid to significantly improve the recovery of the water-based contaminants of heavy …

Semi-Empirical Modeling Of Liquid Carbon's Containerless Solidification, Philip C. Chrostoski

Doctoral Dissertations

“Elemental carbon has important structural diversity, ranging from nanotubes through graphite to diamond. Previous studies of micron-size core/rim carbon spheres extracted from primitive meteorites suggest they formed around such stars via the solidification of condensed carbon-vapor droplets, followed by gas-to-solid carbon coating to form the graphite rims. Similar core/rim particles result from the slow cooling of carbon vapor in the lab. The long-range carbon bond-order potential was used to computationally study liquid-like carbon in (1.8 g/cm³) periodic boundary (tiled-cube supercell) and containerless (isolated cluster) settings. Relaxations via conjugate-gradient and simulated-annealing nucleation and growth simulations using molecular dynamics were …

Cooperative Navigation Of Small Satellites In The Deep Space Environment, Jill Christine Davis

Doctoral Dissertations

“The continued development of small satellites (SmallSats) has made them an increasingly viable mission alternative to traditional monolithic spacecraft. Constellations, swarms, and formations of these small spacecraft have the potential to fill unique gaps in the space systems architecture, while reducing overall mission costs and increasing mission redundancy. Cooperative navigation between spacecraft within swarms and formations is critical to mission success, but poses many challenges for SmallSats due to their size, mass, power, and computing constraints. While Earth orbiting missions can rely on GNSS data for high-accuracy inertial and relative navigation, deep space missions require new navigation techniques. In this …

Mining Haul Road Defect Detection -- Advancement In Automated Road Extent And Response Calibration For Improved Maintenance, Alexander David Douglas

Doctoral Dissertations

Mine haul roads degrade rapidly due to extremely heavy loads on sub optimal construction materials. This research tests two methods of defect detection to determine limitations to current technology: optical detection and vehicle vibration response. Optical defect detection was found to have the least significant limitations for surface defect detection and vehicle vibration response modeling has the least significant limitations for subsurface defects. This research proposes novel methods to eliminate the critical limitations of both technologies.

Unmanned Aerial Vehicles (UAV) equipped with GPS and a high-resolution camera is used to create a 3-D point cloud using a structure-from-motion algorithm. This …

Catalytic Carbon Dioxide Hydrogenation To Methanol/Dimethyl Ether Over Copper-Based Catalysts, Xiao Fan

Doctoral Dissertations

Direct synthesis of dimethyl ether (DME) via CO₂ hydrogenation has received great attention, owing to the global warming caused by CO₂ emission and increasing energy demand worldwide. In this works, three major aspects of bifunctional catalysts development were studied: (1) investigation of the roles of interaction in the CuO-ZnO-ZrO₂-Al₂O₃/HZSM-5 bifunctional catalysts, (2) deactivation and regeneration of CuO-ZnO-ZrO₂-Al₂O₃ with different zeolitic catalysts for one-step CO₂ hydrogenation to dimethyl ether, and (3) study on the enhancement of activity and stability of CZZA/HZSM-5 bifunctional catalysts via the introduction of …

Use Of Portable Seismic Property Analyzer And Ground Penetrating Radar To Assess Bridge Decks, Samie Ramadan A Hamad

Doctoral Dissertations

The Montauk Bridge deck was assessed based on the portable seismic property analyzer and ground penetrating radar data. Based on the analysis of the portable seismic property analyzer data, it was determined that over 65% of bridge conditions were rated serious to poor condition with an average compressive strength of less than 2500 psi; less than 35% of bridge deck conditions were rated fair to good with an average compressive strength over 2500 psi. Based on ground penetrating radar data, it was determined that 72% of the bridge deck was in serious to poor condition, and only 28% of the …

Relating Detonation Parameters To The Detonation Synthesis Of Nanomaterials, Martin Langenderfer

Doctoral Dissertations

“This research investigates the physical and chemical processes that contribute to the detonation synthesis of silicon carbide nanoparticles. Bulk production of SiC nanoparticles through detonation is possible due to pressures achieved over 20 GPa and temperatures over 2000 K as well as quenching rates in excess of 13 billion K/second. These conditions catalyze reaction and bottom-up molecular growth while retaining particles < 100 nm in diameter. In this work, detonation synthesis of SiC was demonstrated by incorporation of polycarbosilane, an SiC precursor material, into an RDX/TNT explosive matrix prior to detonation. Detonation Synthesis of SiC was also accomplished by reacting elemental silicon with carbon liberated by the detonation of negatively oxygen balanced TNT. Hydrodynamic simulation of a 60:40 mass ratio RDX/TNT detonation created conditions thermodynamically suitable to produce cubic silicon carbide within the first 500 nanoseconds after the passage of the detonation wave while carbon remains chemically reactive for molecular formation. Simulations and experimental tests indicated that loading configuration and impedance mismatch of the precursor additives used in detonation synthesis results in conditions in the additives that exceed the accepted detonation pressure of the explosive by greater than three times. Finally, a full factorial experimental design showed increasing silicon concentration, reducing silicon size, and reducing oxygen balance by adjusting the ratio of RDX to TNT decreased the explosives detonation pressure by 20% and increased the soot yield and concentration of SiC observed in the detonation products by 82% and 442% respectively”--Abstract, page iv.

Dynamic Behavior And Interactions Of Ferrofluid Droplets Under Magnetic Fields In Low Reynolds Number Flows, Md Rifat Hassan

Doctoral Dissertations

Digital microfluidics in combination with emulsion microfluidics are crucial building blocks of droplet-based microfluidics, which are prevalent in a wide variety of industrial and biomedical applications, including polymer processing, food production, drug delivery, inkjet printing, and cell-based assays. Therefore, understanding the dynamics and interactions of droplets as well as the interactions between the droplets and solid surfaces are of great importance in order to improve the performance or product in these applications.

Recently, several studies in the literature have demonstrated the potential of magnetic fields in controlling the behavior of droplets in microscale; however, the fundamental mechanism behind the interesting …

Investigation Of Anomalous Data Trends During Coal Dust Explosibilty Testing, Jacob Lee Miller

Doctoral Dissertations

Coal dust explosibility is a health and safety concern that has been a recognized hazard for over 100 years. Initial testing by the Author using a Siwek 20L apparatus recorded a secondary maximum pressure at higher dust concentrations (1,000-7,000g/m³) with Pulverized Pittsburgh Coal (PCC). Higher dust concentrations are beyond the typical ASTM E1226 testing procedure but are possible in mining and processing scenarios. No reference documents have been discovered that show a secondary maximum pressure at higher dust concentrations. Literature reviewed identified that once a coal dust concertation generates a peak pressure, the pressure remains constant or decreases …

An Investigation Of Unsteady Thermal Exchange Processes In Geothermal Heat Exchangers, Ganesh Ravi Shanker

Doctoral Dissertations

“Geothermal heat exchangers, has become one of the highly recognized non conventional heat exchangers as they utilize renewable energy source earth to initiate the thermal energy transfer. However, these heat exchangers suffer from a expensive installation cost due to their conservative design model, thereby facilitating the need to identify and improve the design. In this dissertation, three gaps, which identifies improvement over conservative design were investigated, to assess the heat exchanger performance. In the first approach, borehole thermal and geometrical properties were investigated keeping the outlet leg of the heat exchanger as adiabatic, which neglects the thermal short-circuiting between the …