Engineering Commons^™

Method Of Optimal Battery Scheduling With Optimal Battery And Photovoltaic Sizing, Gideon Hallman

Masters Theses

“Renewable energy generation is on the rise. One of the best ways to capitalize on this intermittent power supply is by using the renewable energy source in tandem with batteries. A joint photovoltaic (PV) and battery system model was created that implemented battery degradation and optimized battery usage using a Markov Decision Process (MDP). This system was then subjected to a series of tests to do a sensitivity analysis while optimizing the battery and PV sizing for the system at hand. Parametric sweeps of solar power and battery capital costs, the cost of energy taken from the grid, the cost …

A Physics-Based Pi Pre-Layout Tool For Pcb Pdn Design, Shuang Liang

Masters Theses

"With increasingly stringent requirements for lower voltage supply, and higher density in PCB PDN design, now integrity (PI) is an increasingly important aspect that must be considered. A pre-layout tool based on the Cavity Model and Boundary Element Method is built to automatically achieve a specified target impedance for a multi-layered Printed Circuit Board (PCB) Power Distribution Network (PDN) design with a minimal number of decoupling capacitors.

The pre-work about the post-layout design and analysis is proposed and the guidelines for creating a decoupling capacitors network with better performance has been built. With limit inputs, physical limitations for the minimal …

The Effects Of Rigid Polyurethane Foam As A Confinement Material On Breaching Charge Detonations, Nathan Franz Paerschke-O'Brien

Masters Theses

"The effects of a rigid polyurethane foam used as a confinement material on four types of breaching explosives were tested, focusing on the changes in shockwave peak pressures, detonation load compression forces, and brisance cratering abilities. The Plate Dent testing procedure was modified to incorporate a load cell force sensor, and two air overpressure sensors were included adjacent to the blast to quantify each test result. The testing variables focused on the polyurethane foam cure times and thickness volumes around the breaching explosives to determine the breaching charges' optimal energy output capabilities when confined by the foam material. The rigid …

Investigation Of The Sensitivity Of Human Arm To Small Interaction Forces During Physical Human-Robot Interaction (Phri), Fazlur Rashid

Masters Theses

“Understanding the human motor control strategy during physical interaction tasks is crucial for developing future robots for physical human-robot interaction (pHRI). Effective pHRI depends on humans communicating their intentions for movement with robots. In physical human-human interaction (pHHI), small interaction forces are known to convey their intent between the partners. It is speculated that small interaction forces contain significant information to convey the movement intention of pHHI. However, the mechanism underlying this interaction strategy is largely unknown. Hence, the aim of this work was to investigate what affects humans’ sensitivity to the interaction forces. The hypothesis was that small interaction …

Transfer Function Measurement For Automotive Intentional Emi And Thermal Runaway Investigation Of Lithium-Ion Battery By Intentional Emi, Woncheol Song

Masters Theses

"With an increasing demand for electric vehicles and autonomous driving, many components of a vehicle are being replaced as electric components. This implicates the possibility of an increase in the malfunction of electric components due to unknown electromagnetic interferences. In this reason, malicious intentional electromagnetic interference (IEMI) is being considered as a growing threat for the current and next generation of automotive technology.

In the first topic, the transfer function between the IEMI attacker and the engine control unit (ECU) circuit in an automobile is extracted to analyze how the IEMI affects the vehicle.

In the second topic, to mimic …

Bond Graph Modeling Of Critical Infrastructures For Cyber-Physical Security Implementation, Michele Jane White

Masters Theses

“In developed societies, there exists infrastructure vital to everyday life. This includes water and power systems. Technology is quickly evolving and being implemented on these utilities. This technology can range from smart metering in neighborhoods to volume sensors in local waste water treatment facilities. When networking, sensing, monitoring, or control devices are integrated with infrastructure it is considered a cyber physical system, or CPS. When information about an important physical system is connected to the virtual world, it is opened up to security risks. Cyber security can be provided to the CPS by monitoring the physical state of the system …

Fabrication Of Silicon Nitride Parts By Ceramic On-Demand Extrusion Process, Sachin Choudhary

Masters Theses

“Ceramic On-Demand Extrusion (CODE) is a patented solid freeform fabrication method for manufacturing high-density monolithic ceramic parts. In the past 5-6 years, the technology has been successfully implemented to fabricate alumina and zirconia parts. The mechanical characterizations also show CODE’s high potential in achieving desired structural properties. The present study covers the fabrication of silicon nitride parts by CODE process, which entailed the design of paste formulation for achieving rheology suitable for dimensional control in fabricated parts and determining firing temperature and the content of sintering additives for silicon nitride green bodies fabricated by CODE. The density, hardness, and fracture …

Research And Development Of A Laser Hot Wire Deposition Process, Christopher Croft

Masters Theses

“Laser hot wire directed energy deposition (DED) is an increasingly popular method for improving deposition rates and overall reduction of build times in DED processing. While there is clear benefit, it is important to fully understand the impact of preheating the wire. This work focuses on developing a model that describes bead geometry output using all factors including the wire preheat. The model was fit with over 150 data points that explored a large range of each factor. The resulting model was then leveraged to evaluate a process control variable. The technique chosen used feedback from the hot wire system …

Seed Modeling Of An Esd Gun Discharge To A Usb Cable, Yang Xu

Masters Theses

“An IC protected by a transient voltage suppression (TVS) diode may fail if the TVS device does not turn on or does not turn on quickly enough, causing the IC to take the full brunt of the electrostatic discharge (ESD) event. Transient simulation models have been developed for ESD protection devices for the purpose of system-efficient ESD design (SEED). The TVS modeling methodology has been improved to better represent the physics that occurs during the TVS response and more accurately predict the interactions between off-chip and on-chip protection devices. Moreover, a complicated test scenario -- an ESD gun discharge through …

Axial Performance Of Self-Consolidating Concrete-Filled Fiber Tubes, Joshua David Carter

Masters Theses

"Concrete filled fiber tubes can be used to increase ductility and strength of a concrete member and self-consolidating concrete is an ideal material to use in practical applications of concrete-filled fiber tubular columns. However, the propensity of self-consolidating concrete to autogenous shrinkage could reduce the effectiveness of the concrete confinement. This research investigates the use of self-consolidating concrete in pre-cast FRP tubes and various methods of shrinkage reduction and compensation to increase the axial performance of said self-consolidating concrete-filled fiber tubes. Axial compression tests were performed under monotonic and cyclic conditions to determine the stress-strain relationship of the self-consolidating concrete …

Development And Characterization Of Nb₃N/Al₂0₃ Superconducting Multilayers For Particle Accelerators, Chris Sundahl, Junki Makita, Paul B. Welander, Yi-Feng Su, Fumitake Kametani, Lin Xie, Huimin Zhang, Lian Li, Alex Gurevich, Chang-Beom Eom

Physics Faculty Publications

Superconducting radio-frequency (SRF) resonator cavities provide extremely high quality factors > 10¹⁰ at 1-2 GHz and 2 K in large linear accelerators of high-energy particles. The maximum accelerating field of SRF cavities is limited by penetration of vortices into the superconductor. Present state-of-the-art Nb cavities can withstand up to 50 MV/m accelerating gradients and magnetic fields of 200-240 mT which destroy the low-dissipative Meissner state. Achieving higher accelerating gradients requires superconductors with higher thermodynamic critical fields, of which Nb₃Sn has emerged as a leading material for the next generation accelerators. To overcome the problem of low vortex penetration …

Effect Of Random Pinning On Nonlinear Dynamics And Dissipation Of A Vortex Driven By A Strong Microwave Current, W.P.M.R. Pathirana, Alex Gurevich

Physics Faculty Publications

We report numerical simulations of a trapped elastic vortex driven by a strong ac magnetic field H(t)=Hsinωt parallel to the surface of a superconducting film. The surface resistance and the power dissipated by an oscillating vortex perpendicular to the film surface were calculated as functions of H and ω for different spatial distributions, densities, and strengths of pinning centers, including bulk pinning, surface pinning, and cluster pinning. Our simulations were performed for both the Bardeen-Stephen viscous vortex drag and the Larkin-Ovchinnikov (LO) drag coefficient η(v) decreasing with the vortex velocity v. The local residual surface resistance R_i(H) …

Magnetic Field Sensors For Detection Of Trapped Flux In Superconducting Radio Frequency Cavities, Ishwari Prasad Parajuli, Gianluigi Ciovati, Jean R. Delayen

Physics Faculty Publications

Superconducting radio frequency (SRF) cavities are fundamental building blocks of modern particle accelerators. They operate at liquid helium temperatures (2–4 K) to achieve very high quality factors (10¹⁰–10¹¹). Trapping of magnetic flux within the superconductor is a significant contribution to the residual RF losses, which limit the achievable quality factor. Suitable diagnostic tools are in high demand to understand the mechanisms of flux trapping in technical superconductors, and the fundamental components of such diagnostic tools are magnetic field sensors. We have studied the performance of commercially available Hall probes, anisotropic magnetoresistive sensors, and flux-gate magnetometers with …

Engineering Thermostable Regulators For Inducible Gene Expression In Thermophiles, Connor M. Joyce

Honors Theses and Capstones

Thermophilic bacteria have attracted research interest due to their ability to grow at high temperatures ranging from 45 °C to 75 °C with some extreme thermophiles able to survive nearly boiling temperatures. They are valuable sources of thermostable biocatalysts and many have great potential as industrial hosts for biofuel production because fermentation at high temperatures has advantages such as reduced processing costs and lower risk of contamination compared with mesophilic bacteria. For example, some Geobacillus species has been shown to have high solvent tolerance, making them good candidates as host for alcohol production. To develop them as industrial hosts, large …

Improving Visual Inspection Reliability In Aircraft Maintenance, Victor Hrymak, Patrick Codd

Conference papers

Visual inspection is a fundamental safety critical task in the air transport industry. This study investigates how a visual search strategy with a specific eye scanning pattern can be used to improve the observation of aircraft defects during visual inspection tasks. N=100 aircraft maintenance technicians were recruited and N=48 were allocated to a control condition. This group conducted pre-flight visual inspections on aircraft, using their normal custom and practice. The remaining N=52 experimental group participants were trained to use a specific eye scanning pattern during their pre-flight inspection called systematic visual search. Prior to inspections, the number of observable defects …

Better Heat And Power Integration Of An Existing Gas-Oil Plant In Egypt Through Revamping The Design And Organic Rankine Cycle, Mamdouh A. Gadalla, Alaa Elmasry, Ibrahim Alhajri, Fatma H. Ashour, Hany A. Elazab

Chemical and Biochemical Engineering Faculty Research & Creative Works

Objective: The current study aims mainly to Maximize Condensate Recovery (NGLs), focusing on a gas processing train of Gas-Oil Separation Plant (GOSP) located in Egypt with a capacity of 4,230 kmole/h. Methods: The research study accounts for the constraint of Reid Vapor Pressure (RVP) specification, which makes the storage in floating roof tanks is of a great risk. The study proposes the installation of the cryogenic train that recovers condensates (C4+). This train comprises of compression unit, expansion unit, three-phase separators and a re-boiled absorber. The problem of RVP will no longer exist because of the re-boiled absorber achieving RVP …

Equilibrium And Kinetic Study On The Biosorption Of Trypan Blue From Aqueous Solutions Using Avocado Seed Powder, Tamer T. El-Idreesy, Omar Khoshala, Amin Firouzi, Hany A. Elazab

Chemical and Biochemical Engineering Faculty Research & Creative Works

This research aims to investigate the removal of trypan blue dye from aqueous solutions by employing ground avocado seeds powder, a low-cost biowaste adsorbent (biosorbent), under various experimental conditions. The effect of contact time, initial dye concentration, and adsorbent dose on dye removal were studied. The experimental kinetic data were fitted to pseudo-first order and pseudo-second-order kinetic models. Results imply that adsorption of trypan blue on the avocado seed adsorbent nicely followed the pseudo-second-order kinetic model. Equilibrium isotherms were analyzed by Langmuir and Freundlich isotherms, where Langmuir isotherm described the isotherm data with a high-correlation coefficient (R2=0.9948) closer to unity, …

Enhancing Mixed Traffic Flow Safety Via Connected And Autonomous Vehicle Trajectory Planning With A Reinforcement Learning Approach, Yanqiu Cheng, Chenxi Chen, Xianbiao Hu, Kuanmin Chen, Qing Tang, Yang Song

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The longitudinal trajectory planning of connected and autonomous vehicle (CAV) has been widely studied in the literature to reduce travel time or fuel consumptions. The safety impact of CAV trajectory planning to the mixed traffic flow with both CAV and human-driven vehicle (HDV), however, is not well understood yet. This study presents a reinforcement learning modeling approach, named Monte Carlo tree search-based autonomous vehicle safety algorithm, or MCTS-AVS, to optimize the safety of mixed traffic flow, on a one-lane roadway with signalized intersection control. Crash potential index (CPI) is defined to quantitively measure the safety performance of the mixed traffic …

Sub-Micron Moulding Topological Mass Transport Regimes In Angled Vortex Fluidic Flow, Thaar M. D. Alharbi, Matt Jellicoe, Xuan Luo, Kasturi Vimalanathan, Ibrahim K. Alsulami, Bediea S. Al Harbi, Aghil Igder, Fayed A. J. Alrashaidi, Xianjue Chen, Keith A. Stubbs, Justin M. Chalker, Wei Zhang, Ramiz A. Boulos, Darryl B. Jones, Jamie S. Quinton, Colin L. Raston

Research outputs 2014 to 2021

Shear stress in dynamic thin films, as in vortex fluidics, can be harnessed for generating non-equilibrium conditions, but the nature of the fluid flow is not understood. A rapidly rotating inclined tube in the vortex fluidic device (VFD) imparts shear stress (mechanical energy) into a thin film of liquid, depending on the physical characteristics of the liquid and rotational speed,ω, tilt angle,θ, and diameter of the tube. Through understanding that the fluid exhibits resonance behaviours from the confining boundaries of the glass surface and the meniscus that determines the liquid film thickness, we have established specific topological mass transport regimes. …

Drastic Enhancement Of Co2 Adsorption Capacity By Negatively Charged Sub-Bituminous Coal, Hussein R. Abid, Stefan Iglauer, Ahmed Al-Yaseri, Alireza Keshavarz

Research outputs 2014 to 2021

Climate change is a key problem of the 21st century. Climate change is mainly caused by anthropogenic CO₂ emissions, and one solution to this problem is to capture and store CO₂ in deep coal seams, where it is immobilized by adsorption to the coal surface. Here we propose to modify the coal with methyl orange (MO), a typical dye that is also a major pollutant of the hydrosphere and removed thereby. Thus, raw and MO-modified coals were characterized to investigate their thermal stabilities, textural properties, carbon contents, surface characteristics, and CO₂ adsorption on the coal samples was …

Design And Perspective Of Amorphous Metal Nanoparticles From Laser Synthesis And Processing, Shun-Xing Liang, Lai-Chang Zhang, Sven Reichenberger, Stephan Barcikowski

Research outputs 2014 to 2021

Amorphous metal nanoparticles (A-NPs) have aroused great interest in their structural disordering nature and combined downsizing strategies (e.g. nanoscaling), both of which are beneficial for highly strengthened properties compared to their crystalline counterparts. Conventional synthesis strategies easily induce product contamination and/or size limitations, which largely narrow their applications. In recent years, laser ablation in liquid (LAL) and laser fragmentation in liquid (LFL) as "green"and scalable colloid synthesis methodologies have attracted extensive enthusiasm in the production of ultrapure crystalline NPs, while they also show promising potential for the production of A-NPs. Yet, the amorphization in such methods still lacks sufficient rules …

Rgb-D Data-Based Action Recognition: A Review, Muhammad Bilal Shaikh, Douglas Chai

Research outputs 2014 to 2021

Classification of human actions is an ongoing research problem in computer vision. This review is aimed to scope current literature on data fusion and action recognition techniques and to identify gaps and future research direction. Success in producing cost-effective and portable vision-based sensors has dramatically increased the number and size of datasets. The increase in the number of action recognition datasets intersects with advances in deep learning architectures and computational support, both of which offer significant research opportunities. Naturally, each action-data modality—such as RGB, depth, skeleton, and infrared (IR)—has distinct characteristics; therefore, it is important to exploit the value of …

Corrosion Behavior And Characteristics Of Passive Films Of Laser Powder Bed Fusion Produced Ti-6al-4v In Dynamic Hank’S Solution, Liang-Yu Chen, Hong-Yue Zhang, Chuanbo Zheng, Hong-Yu Yang, Peng Qin, Cuihua Zhao, Sheng Lu, Shun-Xing Liang, Linjiang Chai, Lai-Chang Zhang

Research outputs 2014 to 2021

The corrosion behavior of laser powder bed fusion produced (L-PBF-produced) titanium alloys involving flowing body fluid is still unclear. Therefore, this work investigates in vitro corrosion behavior and the characteristics of passive films formed on L-PBF-produced Ti–6Al–4V in both static and dynamic Hank’s solutions. Electrochemical measurements, immersion tests, X-ray photoelectron spectroscopy and scanning electron microscopy were conducted. In comparison to the L-PBF-produced Ti–6Al–4V in static Hank’s solution, the samples showed lower charge transfer resistance and higher passivation current density (anodic current density as well) in dynamic Hank’s solution. Meanwhile, a more apparent deposition of apatite and hydroxyapatite is found on …

The Effect Of Tin-, Ticn-, Tialn-, And Tisin Coated Tools On The Surface Defects And Geometric Tolerances Of Holes In Multi-Spindle Drilling Of Al2024 Alloy, Muhammad Aamir, Adrian Davis, William Keeble, Ugur Koklu, Khaled Giasin, Ana Vafadar, Majid Tolouei Rad

Research outputs 2014 to 2021

The integrity of machined holes depends on many parameters, some of which are related to the cutting tool (geometry, coating, material). Other influential parameters are related to the machining process variables (spindle speed, feed rate, workpiece material), all of which can affect the quality of the hole and drilling induced damage on its surface. This study investigates the effect of uncoated tools and four types of tool coatings (TiN-, TiCN-, TiAlN-, and TiSiN) on the hole quality and its microstructure. The study analyzed several hole geometrical metrics, namely hole size, circularity, cylindricity, and perpendicularity of an Al2024 aluminum alloy using …

Effect Of Nb On Β→Α″ Martensitic Phase Transformation And Characterization Of New Biomedical Ti-Xnb-3fe-9zr Alloys, Syed Faraz Jawed, Chirag Dhirajlal Rabadia, Fahad Azim, Saad Jawaid Khan

Research outputs 2014 to 2021

A new generation of Ti-xNb-3Fe-9Zr (x=15, 20, 25, 30, 35 wt %) alloys have been designed using various theoretical approaches including DV-xα cluster, molybdenum equivalency, and electron to atom ratio. Afterward, designed alloys are fabricated using cold crucible levitation melting technique. The microstructure and mechanical performances of newly designed alloys are characterized in this work using scanning electron microscope and universal testing machine, respectively. Each alloy demonstrates monolithic β phase except Ti-35Nb-3Fe-9Zr alloy which display dual α″+β phases. Typically, niobium acts as an isomorphous beta stabilizer. However, in this work, formation of martensitic α″ phases occurs at 35 wt % …

Shale Adhesion Force Measurements Via Atomic Force Microscopy, Nikolai Mitiurev, Michael Verrall, Svetlana Shilobreeva, Alireza Keshavarz, Stefan Iglauer

Research outputs 2014 to 2021

Wettability of sedimentary rock surface is an essential parameter that defines oil recovery and production rates of a reservoir. The discovery of wettability alteration in reservoirs, as well as complications that occur in analysis of heterogeneous sample, such as shale, for instance, have prompted scientists to look for the methods of wettability assessment at nanoscale. At the same time, bulk techniques, which are commonly applied, such as USBM (United States Bureau of Mines) or Amott tests, are not sensitive enough in cases with mixed wettability of rocks as they provide average wettability values of a core plug. Atomic Force Microscopy …

Current Advances In Syngas (Co + H2) Production Through Bi-Reforming Of Methane Using Various Catalysts: A Review, U. S. Mohanty, Muhammad Ali, Muhammad Rizwan Azhar, Ahmed Al-Yaseri, Alireza Keshavarz, Stefan Iglauer

Research outputs 2014 to 2021

Today, bi - reforming of methane is considered as an emerging replacement for the generation of high-grade synthesis gas (H₂:CO = 2.0), and also as an encouraging renewable energy substitute for fossil fuel resources. For achieving high conversion levels of CH₄, H₂O, and CO₂ in this process, appropriate operation variables such as pressure, temperature and molar feed constitution are prerequisites for the high yield of synthesis gas. One of the biggest stumbling blocks for the methane reforming reaction is the sudden deactivation of catalysts, which is attributed to the sintering and coke formation …

Co2 – Brine – Sandstone Wettability Evaluation At Reservoir Conditions Via Nuclear Magnetic Resonance Measurements, Auby Baban, Ahmed Al-Yaseri, Alireza Keshavarz, R. Amin, Stefan Iglauer

Research outputs 2014 to 2021

CO₂-rock wettability is a key parameter which governs CO₂ trapping capacities and containment security in the context of CO₂ geo-sequestration schemes. However, significant uncertainties still exist in terms of predicting CO₂ rock wettability at true reservoir conditions. This study thus reports on wettability measurements via independent Nuclear Magnetic Resonance (NMR) experiments on sandstone (CO₂–brine systems) to quantify Wettability Indices (WI) using the United States Bureau of Mines (USBM) scale. The results show that CO₂ (either molecularly dissolved or as a separate supercritical phase) significantly reduced the hydrophilicity of the sandstone from strongly …

Applications Of Membranes For Sustainability, Veeriah Jegatheesan, Chettiyappan Visvanathan, Li Shu, Faisal I. Hai, Ludovic F. Dumée

Research outputs 2014 to 2021

Applications of membranes in water and wastewater treatment, desalination, as well as other purification processes, have become more widespread over the past few decades. However, we continue to ponder on (i) how well do we get maximum benefits from membrane applications? (ii) In what areas of membranes do we need to further our fundamental understanding? (iii) Which membrane technologies find difficulties in scale-up? (iv) How good are we in integrating membrane technologies? (v) How can we improve the reliability of membranes and reduce the cost? (vi) Where are we in disseminating the needs if we are to use membranes all …

Kinetic Study Of Product Distribution Using Various Data-Driven And Statistical Models For Fischer-Tropsch Synthesis, Yixiao Wang, Jing Hu, Xiyue Zhang, Abubakar Yusuf, Binbin Qi, Huan Jin, Yiyang Liu, Jun He, Yunshan Wang, Gang Yang, Yong Sun

Research outputs 2014 to 2021

Three modeling techniques, namely, a radial basis function neural network (RBFNN), a comprehensive kinetic with genetic algorithm (CKGA), and a response surface methodology (RSM), were used to study the kinetics of Fischer-Tropsch (FT) synthesis. Using a 29 × 37 (4 independent process parameters as inputs and corresponding 36 responses as outputs) matrix with total 1073 data sets for data training through RBFNN, the established model is capable of predicting hydrocarbon product distribution i.e., the paraffin formation rate (C2-C15) and the olefin to paraffin ratio (OPR) within acceptable uncertainties. With additional validation data sets (15 × 36 matrix with total 540 …