Engineering Commons^™

Optimization Of Nitrogen Removal Rate In One-Stage Reactor Through Partial Nitrification Anammox Process During Direct Treatment Of Poultry Litter Wastewater, Yiting Xiao

Graduate Theses and Dissertations

Anammox is an increasingly common process used for the treatment of reject water and even mainstream wastewater due to its low oxygen demand. However, anammox is not commonly utilized in the direct treatment of poultry litter because of the high organic content, which would inhibit the anammox process. Thus, this project is aimed at optimizing the nitrogen removal rate through partial nitrification anammox process (PN/A) to treat synthetic poultry litter wastewater. Nitrogen removal efficiencies will therefore be improved through optimizing the combination of three operating parameters including hydraulic retention time (HRT), dissolved oxygen (DO) concentration, and carbon to nitrogen (C/N) …

Roadway-Embedded Transmitters And Multi-Pad Receivers For High Power Dynamic Wireless Power Transfer, Benny J. Varghese

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Electric vehicles (EVs) offer considerable economic and environmental benefits to society. Despite the decreasing vehicle costs and increasing range of newer EVs, the problem of range anxiety still exists. Range anxiety, at its core, is an issue of charging speeds rather than a concern about the driving range. Dynamic wireless charging of EVs is seen as a potential solution to this issue of range anxiety. Further, wireless charging technology also helps the push towards level 5 autonomy and opens new opportunities for how an EV can be utilized.

Dynamic wireless power transfer (DWPT) systems typically require a high initial investment …

Flow Choice Architecture: Cognitive Augmentation Of Knowledge Workers, Troy Ricardo Weekes

Theses and Dissertations

The Flow Choice Architecture (FCA) is a biofeedback-based behavior modification tool that was designed for operation by human knowledge workers (KWs) before, during, and after the performance of work tasks. FCA utilizes human-aware artificial intelligence (AI) that senses patterns in its operator’s bio-signals to derive their cognitive and affective states. The states are contextualized using relevant information about the operator, task, and work timeline. The contextualized operator states are then used to recommend effective nudges that orient the human KW towards the flow state. This dissertation outlines the state-of-the-art on flow, neurofeedback, and AI then explains how FCA was designed, …

Effects Of Aging On Mouse Rotator Cuff Tendon Biomechanics, Chinmay Sagar Patwardhan

Bioengineering Theses - Archive

Rotator cuff tendon injuries and tear are caused by overuse, falling, or other accidents, and are often associated with old age. The severe injuries and tear can be debilitating and require nonsurgical treatment for partial tear and arthroscopic surgery for complete tear. The frequent location of injuries and tear are at the enthesis region, the interface where the tendon tissue gradually hardens and merges into the bone. Although aging has been identified as an important factor for rotator cuff tendon injuries and tear, how the mechanical properties of the bone-tendon complex evolve along with age is still a knowledge gap. …

Microstructure And Mechanical Properties Of Cast And Hot-Rolled Medium-Carbon Steels Under Isothermal Heat-Treatment Conditions, Byungsue Shin, Kwangyuk Kim, Sung Yi, Sanggyu Choi, Soongkeun Hyun

Mechanical and Materials Engineering Faculty Publications and Presentations

In this study, the changes in the microstructure and mechanical properties during isothermal heat treatment of cast steel before and after hot deformation were investigated using medium carbon steel with low alloy content. The microstructural characteristics of the cast and hot-rolled medium-carbon steel under isothermal heat-treatment conditions were examined using optical microscopy and scanning electron microscopy in conjunction with electron backscatter diffraction. The variation in the mechanical properties was evaluated using Rockwell hardness and tensile tests. After maintaining an austenitizing condition at 1200 ◦C for 30 min, an isothermal heat treatment was performed in the range 350–500 ◦C, followed by …

A Linear Dynamical Perspective On Epidemiology: Interplay Between Early Covid-19 Outbreak And Human Mobility, Shakib Mustavee

Electronic Theses and Dissertations, 2020-2023

This research investigates the impact of human activity and mobility (HAM) in the spreading dynamics of an epidemic. Specifically, it explores the interconnections between HAM and its effect on the early spread of the COVID-19 virus. During the early stages of the pandemic, effective reproduction numbers exhibited a high correlation with human mobility patterns, leading to a hypothesis that the HAM system can be studied as a coupled system with disease spread dynamics. This study applies the generalized Koopman framework with control inputs to determine the nonlinear disease spread dynamics and the input-output characteristics as a locally linear controlled dynamical …

Predicting Zero Bin In The Semiconductor Manufacturing Industry: Machine Learning Algorithms, Yazmin Montoya

Open Access Theses & Dissertations

The semiconductor industry has faced supply chain manufacturing shortages that ultimately led to a worldwide chip shortage during the COVID-19 pandemic. These chip manufacturers use sophisticated and advanced manufacturing machinery in their fabs to manufacture chips. As experienced during the pandemic, manufacturing unavailability is often due to the lack of critical manufacturing-related spare parts. This thesis evaluates the effectiveness of machine learning algorithms to identify significant factors contributing to manufacturing part outages (i.e., zero-bin) to keep manufacturing equipment running at total capacity within the organization. We propose clustering methods to segment the data and use logistic regression, logistic lasso regression, …

Modeling Driver Distraction Mechanism And Its Safety Impact In Automated Vehicle Environment., Song Wang

Electronic Theses and Dissertations

Automated Vehicle (AV) technology expects to enhance driving safety by eliminating human errors. However, driver distraction still exists under automated driving. The Society of Automotive Engineers (SAE) has defined six levels of driving automation from Level 0~5. Until achieving Level 5, human drivers are still needed. Therefore, the Human-Vehicle Interaction (HVI) necessarily diverts a driver’s attention away from driving. Existing research mainly focused on quantifying distraction in human-operated vehicles rather than in the AV environment. It causes a lack of knowledge on how AV distraction can be detected, quantified, and understood. Moreover, existing research in exploring AV distraction has mainly …

Additive Manufacturing Using Robotic Manipulators, Fdm, And Aerosol Jet Printers., Alexander Curry

Electronic Theses and Dissertations

Additive manufacturing has created countless new opportunities for fabrication of devices in the past few years. Advances in additive manufacturing continue to change the way that many devices are fabricated by simplifying processes and often lowering cost. Fused deposition modeling (FDM) is the most common form of 3D printing. It is a well-developed process that can print various plastic materials into three-dimensional structures. This technology is used in a lot of industries for rapid prototyping and sometimes small batch manufacturing. It is very inexpensive, and a prototype can be created in a few hours, rather than days. This is useful …

An Investigation Into Energy-Material Properties Interaction In Additive Manufacturing Of Polymers., Pu Han

Electronic Theses and Dissertations

Additive manufacturing (AM), known as three-dimensional (3D) printing, is a fabrication process to build 3D objects layer by layer based on computer aided design (CAD) model or digital 3D model. Fused filament fabrication (FFF) has become a preferred method for additive manufacturing due to its cost-effectiveness and flexibility. However, the parts built using FFF process suffer from lower mechanical strength compared to that fabricated using traditional method and rough surface finish. With this motivation, this dissertation aims to develop and implement a novel in-process laser assisted technique on FFF to heal the microstructure of FFF built objects by enhancing reptation …

Analyzing The Non-Isothermal Multiphasic Flow In Porous Media Through Strongly Coupled Thermo-Hydro-Mechanical Modeling., Mohammadreza Mir Tamizdoust

Electronic Theses and Dissertations

Underground geo-structures and climate change can trigger coupled heat, moisture, and vapor flow in shallow and deep subsurface which is frequently referred to as non-isothermal multiphase flow. The coupled multiphasic flow in soil may induce volumetric shrinkage or expansion deformation depending on the thermo-hydraulic loading condition. In saturated porous media, temperature gradient and heat transfer may affect pore fluid pressure and/or pore fluid flow depending on thermal, mechanical, and hydraulic properties of the media and the saturating fluid. In vadose zones, the prediction of coupled nonisothermal multiphase flow in porous media has been the subject of many theoretical and experimental …

Estimating Smart Wi-Fi Thermostat-Enabled Thermal Comfort Control Savings For Any Residence, Abdulelah D. Alhamayani, Qiancheng Sun, Kevin Hallinan

Mechanical and Aerospace Engineering Faculty Publications

Nowadays, most indoor cooling control strategies are based solely on the dry-bulb temperature, which is not close to a guarantee of thermal comfort of occupants. Prior research has shown cooling energy savings from use of a thermal comfort control methodology ranging from 10 to 85%. The present research advances prior research to enable thermal comfort control in residential buildings using a smart Wi-Fi thermostat. "Fanger's Predicted Mean Vote model" is used to define thermal comfort. A machine learning model leveraging historical smart Wi-Fi thermostat data and outdoor temperature is trained to predict indoor temperature. A Long Short-Term-Memory neural network algorithm …

Long Haulers: The Us Airline Industry And Moving Forward From The Covid-19 Pandemic, James Norman

Aviation Faculty Publications

No abstract provided.

Synthesis And Assessment Of Sustainable Fuels For Transportation And Space Exploration, Katerina Chagoya

Electronic Theses and Dissertations, 2020-2023

As global energy sources transition towards renewable energy, the demand for sustainable fuels has never been greater. The sheer scale of this transition will require numerous solutions to accommodate for the diverse and complex situations worldwide. This dissertation will discuss 3 studies: the utilization of CO2 waste gas to produce fuels sustainably, characterizing biofuels for efficient use in automobiles, and developing a solid, emissonless fuel intended for spaceflight but also applicable on Earth. The hydrogenation of CO2 into value-added molecules could reduce greenhouse gas emissions if waste stream CO2 were captured for conversion. We found that atomic vacancies induced in …

3d Printing In Cardiology: A Review Of Applications And Roles For Advanced Cardiac Imaging, Ellen M. Lindquist, Jordan M. Gosnell, Sana K. Khan, John L. Byl, Weihua Zhou, Jingfeng Jiang, Et. Al.

Michigan Tech Publications, Part 1

With the rate of cardiovascular diseases in the U.S increasing throughout the years, there is a need for developing more advanced treatment plans that can be tailored to specific patients and scenarios. The development of 3D printing is rapidly gaining acceptance into clinical cardiology.

In this review, key technologies used in 3D printing are briefly summarized, particularly, the use of artificial intelligence (AI), open-source tools like MeshLab and MeshMixer, and 3D printing techniques such as fused deposition molding (FDM) and polyjet are reviewed. The combination of 3D printing, multiple image integration, and augmented reality may greatly enhance data visualization …

Smart Metering Communication Protocols And Performance Under Cyber Security Vulnerabilities, Oscar A. Alvarez

Theses and Dissertations

The communication process is the key that characterizes the modern concept of smart grid, a new technology that introduced a “two-way communication” in energy measurement systems and can be best represented through the smart meters. Hence, the goal of smart metering communication is to ensure a secure and reliable transmission of information that can only be accessed by end users and energy supplying companies. With the goal of improving the information security in smart energy grids, the research presented in this work focused on studying different advanced metering infrastructure communication protocols and, it showcases a series of experiments performed on …

Synthesize And Characterization Of Aluminum- Tungsten Carbide Nanocomposite, Shuvendu Das

Theses and Dissertations

This research focuses on developing metal matrix composite reinforced by polymer-derived ceramic fibers. The force-spun AMT nanofibers were heat treated into tungsten carbide and then mixed with aluminum powder using cold pressing and sintering to produce the composites. The basic mechanical properties of this composite are investigated by density measurement, hardness and compression testing. SEM, EDS and XRD were used to test the morphology of tungsten carbide fibers. EDS identified a near-perfect W-C ratio in tungsten carbide fibers 1000 °C. Tungsten Carbide fibers were crushed using ball milling technique. Tungsten carbide nanofibers powder had a variety of particle size. Results …

Development Of Metamaterial-Based Near-Zero Refractive Index Structures In The Optical Regime, Andres Ochoa

Theses and Dissertations

Multilayer combinations of plasmonic and dielectric materials can be designed as subwavelength structures to create a medium with unique parameters, but the development of optical metamaterials for the visible spectrum is hindered by the lack of plasmonic materials with suitable properties. A method to understand and design metamaterials for optical applications is examined as a solution for shifting the operating range from ultraviolet light to visible light. Special points of interest and corresponding parameters are identified to understand their effects on propagation. A hyperbolic near-zero refractive index metamaterial composed of alternating layers of metal and perovskite thin films is proposed …

Comparisons Of Concrete Slender Wall Software With Full-Scale Experiments, Gloriana M.L. Moua

Architectural Engineering

The 1980 slender wall testing was performed by the Structural Engineers Association of Southern California (SEAOSC) in efforts to analyze behavior of concrete slender walls when lateral and eccentric axial loads are applied. The testing was done with 12 tilt-up wall panels, 3 of each of the four thicknesses: 9 ½”, 7 ¼”, 5 ¾”, and 4 ¾”. What was discovered from testing was that a fixed limitation of height to thickness ratio was not a governing factor and that each case should be analyzed based off the strength and deflection of the wall. It was because of this testing …

Effects Of Graphical In-Flight Weather Information And Graphical Depictions Of Airspace Restrictions On Pilots’ Decisions To Continue Vfr Flight Into Imc, Andrew James Nakushian

Theses and Dissertations

Continued Visual Flight Rules (VFR) flight into Instrument Meteorological Conditions (IMC) is a leading cause of fatal general aviation accidents. According to the 2020 Joseph T. Nall Report, this type of accident has a 90% lethality rate. As a result of this high lethality rate, VFR into IMC is an aviation safety issue widely discussed among the aviation community in popular media and academic literature. Additionally, over the past decade, Electronic Flight Bags (EFBs) have become mainstream in general aviation, replacing paper charts and providing inflight weather in both graphical and textual form. EFBs also commonly provide graphical depictions of …

Building And Infrastructure Defect Detection And Visualization Using Drone And Deep Learning Technologies, Yuhan Jiang, Sisi Han, Yong Bai

Civil and Environmental Engineering Faculty Research and Publications

This paper presents an accurate and stable method for object and defect detection and visualization on building and infrastructural facilities. This method uses drones and cameras to collect three- dimensional (3D) point clouds via photogrammetry, and uses orthographic or arbitrary views of the target objects to generate the feature images of points’ spectral, elevation, and normal features. U-Net is implemented in the pixelwise segmentation for object and defect detection using multiple feature images. This method was validated on four applications, including on-site path detection, pavement cracking detection, highway slope detection, and building facade window detection. The comparative experimental results confirmed …

Slicing-Based Artificial Intelligence Service Provisioning On The Network Edge: Balancing Ai Service Performance And Resource Consumption Of Data Management, Mushu Li, Jie Gao, Conghao Zhou, Xuemin Shen, Weihua Zhuang

Civil and Environmental Engineering Faculty Research and Publications

Edge intelligence leverages computing resources on the network edge to provide artificial intelligence (AI) services close to network users. As it enables fast inference and distributed learning, edge intelligence is envisioned to be an important component of 6G networks. In this article, we investigate AI service provisioning for supporting edge intelligence. First, we present the features and requirements of AI services. Then we introduce AI service data management and customize network slicing for AI services. Specifically, we propose a novel resource-pooling method to regularize service data exchange within the network edge while allocating network resources for AI services. Using this …

Progress And Prospect Of Anodic Oxidation For The Remediation Of Perfluoroalkyl And Polyfluoroalkyl Substances In Water And Wastewater Using Diamond Electrodes, Sean T. Mcbeath, Adrián Serrano Mora, Fatemeh Asadi Zeidabadi, Brooke K. Mayer, Patrick J. Mcnamara, Madjid Mohseni, Michael R. Hoffman, Nigel J. D. Graham

Civil and Environmental Engineering Faculty Research and Publications

Although diamond electrodes are widely used in the field of electroanalysis and sensing, their application in the field of environmental engineering has yet to be fully realized. Many research studies have considered their potential application in water and wastewater treatment, where the in-situ electrochemical process can avoid the need for chemical additives by facilitating the oxidation of pollutants on the electrode surface or mediated by electrochemically synthesized oxidants in solution. Diamond-based electro-oxidation can effectively treat a number of organic micropollutants and is now being evaluated for the abatement of perfluoroalkyl and polyfluoroalkyl substances, which pose health concerns and are ubiquitous …

Fabricating Nanophotonic Devices Using Nanofabrication Techniques, Scott Cummings

Student Scholar Symposium Abstracts and Posters

Nanofabrication processes are widely used to make the integrated circuits and computer chips that are ubiquitous in today’s technology. These fabrication processes can also be applied to the creation of nanophotonic devices. The ways in which we apply these fabrication techniques in the field of photonics is often constrained by the technologies used for electronics manufacturing which presents an interesting engineering challenge. These limitations include availability and cost of certain fabrication equipment and techniques required to create state-of-the-art nanophotonic devices. Through work with the University of California Irvine nano-fabrication cleanroom, we designed and fabricated various integrated photonic components including grating …

The Bridge Newsletter Winter 2021, Missouri University Of Science And Technology

The Bridge Newsletter

-S&T contributes to infrastructure through national center
-Brinkmann leads Missouri Highways and Transportation Commission
-Wu wins NSF CAREER Award for 2D metals work
-Academy of Civil Engineers induction and 150^th celebration

Incorporation Of Zinc In Pre-Alloyed Cuin[Zn]S2/Zns Quantum Dots, Jean Carlos Morales Orocu

Graduate Theses and Dissertations

Since the early 2000s heavy-metal-free quantum dots (QDs) such as CuInS2/ZnS have attempted to replace CdSe, their heavy-metal-containing counterparts. CuInS2/ZnS is synthesized in a two-step process that involves the fabrication of CuInS2 (CIS) nanocrystals (NCs) followed by the addition of zinc precursors. Instead of the usual core/shell architecture often exhibited by binary QDs, coating CIS QDs results in alloyed and/or partially alloyed cation-exchange (CATEX) QDs. The effect that zinc has on the properties of CIS NCs was studied by incorporating zinc during the first step of the synthesis. Different In:Cu:Zn ratios were employed in this study, maintaining a constant 4:1 …

Design, Extraction, And Optimization Tool Flows And Methodologies For Homogeneous And Heterogeneous Multi-Chip 2.5d Systems, Md Arafat Kabir

Graduate Theses and Dissertations

Chip and packaging industries are making significant progress in 2.5D design as a result of increasing popularity of their application. In advanced high-density 2.5D packages, package redistribution layers become similar to chip Back-End-of-Line routing layers, and the gap between them scales down with pin density improvement. Chiplet-package interactions become significant and severely affect system performance and reliability. Moreover, 2.5D integration offers opportunities to apply novel design techniques. The traditional die-by-die design approach neither carefully considers these interactions nor fully exploits the cross-boundary design opportunities.

This thesis presents chiplet-package cross-boundary design, extraction, analysis, and optimization tool flows and methodologies for high-density …

Validation Of Computational Model Of A Piezoelectric Flow Rate Sensor, Eben Roberto Escobedo

Open Access Theses & Dissertations

This study validates a computational simulation of a piezoelectric cantilever beam undergoing different loads by showing a comparison of its results against theoretical calculations. The objective of the computational model is to simulate the behavior of a beam made of a piezoelectric material which can be used as a flow rate sensor due to the ability of the material to convert a mechanical load into an electrical load. After validating the model, different geometries, material properties and loads can be simulated to observe the different behaviors and bring the possibility of selecting the most convenient options according to the needs …

An Investigation Of Phosphorus Removal By Purple Bacteria In Dairy Wastewater Lagoons, Lauren M. Gomez, Andrew J. Schuler, Jose M. Cerrto, David T. Hanson

Civil Engineering ETDs

The objective of this study was to determine whether the polyphosphate metabolism in purple photosynthetic bacteria (PPB) is similar to that of wastewater polyphosphate-accumulating organisms (PAOs) such as Accumulibacter. Dairy lagoon samples were studied in continuous and batch laboratory tests to evaluate whether cyclic light and dark conditions for PPB are similar to aerobic and anaerobic conditions for PAOs in domestic wastewater treatment systems. 16s rRNA gene amplicon sequencing indicated the presence of the purple sulfur bacterium Thiolamprovum (53.92%) in one lagoon source, and Thiodictyon (3.50%) in a second lagoon. Phosphorus contents were at least 0.7% higher than the …

Evaluation Of A Novel Approach For Assessing Biological Activity In Agricultural Soils, Karla Melgar

Department of Agricultural and Biological Systems Engineering: Dissertations, Theses, and Student Research

Soil health is a key factor impacting soil resilience and fertility in crop production systems. Favorable soil physical and biological conditions facilitate plant nutrient absorption and nutrient cycling. Demonstrating to farmers the impacts and changes in soil biological activity under different soil management practices has been a challenge due to the limited availability of inexpensive tools for quantifying this component of soil health. The primary goal of this study was to present a simple and readily accessible tool for evaluating soil biological activity to promote the use of organic amendments in crop fields. Research plots were established in two studies …