Engineering Commons^™

Conceptual Design Methodology For The Fan-In-Wing Vtol Aircraft, Brock Steinfeldt

Doctoral Dissertations and Master's Theses

The Fan-In-Wing (FIW) aircraft concept is one of the most compelling solutions for missions demanding jet-like cruise speeds and Vertical TakeOff and Landing (VTOL) capability. However, despite years of interest and documented improvements in lift-fan technology, there exists little in the way of an adequate theory for conceptual design of a fan-in-wing aircraft. To address this issue, a general conceptual design methodology has been developed as a source of guidance for the FIW designer. Through this work, the top-level requirements ranking the fan-in-wing concept above other VTOL aircraft have been defined, while a cross-comparison between the FIW concept and conventional …

The Use Of Virtual Reality Training Environments For Procedural Training In Fourth-Generation Airliners, Mark Edgar Mccullins

Doctoral Dissertations and Master's Theses

This study examined the effectiveness of using virtual reality training environments for procedural training in fourth-generation airliners. Its goal was to assess whether the training outcomes from a recurrent training course for FAA certificated Airframe and Powerplant (A&P) technicians, which used a Full Flight Simulator (FFS) to deliver and assess training, differed from the same training delivered using a Virtual Reality (VR) device.

The study used an experimental design with three groups and two within-group measures of training effectiveness. The control group followed the current training program and was assessed in the FFS, while the second group was trained using …

State Omniscience For Cooperative Local Catalog Maintenance Of Close Proximity Satellite Systems, Chris Hays

Doctoral Dissertations and Master's Theses

Resiliency in multi-agent system navigation is reliant on the inherent ability of the system to withstand, overcome, or recover from adverse conditions and disturbances. In large part, resiliency is achieved through reducing the impact of critical failure points to the success and/or performance of the system. In this view, decentralized multi-agent architectures have become an attractive solution for multi-agent navigation, but decentralized architectures place the burden of information acquisition directly on the agents themselves. In fact, the design of distributed estimators has been a growing interest to enable complex multi-sensor/multi-agent tasks. In such scenarios, it is important that each local …

Starfish: A Compact, Biomimetic, And Adaptive Shape Memory Alloy Orbital Debris Remover, Katelyn Branaman

Doctoral Dissertations and Master's Theses

This thesis aims to turn the tides on the orbital debris issue through the fabrication and demonstration of a compact, biomimetic, and adaptive shape memory alloy actuated orbital debris remover. The design, referred to as Starfish, is discussed in detail along with its fabrication process and object capture ability. A hard skeleton crafted from PETG was combined with shape memory alloy wires and extension springs to create a biomimetic structure that operates similar to the human hand, capable of gripping a wide range of objects. Relevant simulations were performed and discussed, the iterative fabrication process used to create each component …

Trustable Adaptive Controllers For Multi-Agent Systems With Actuator Dynamics, Atahan Kurttisi

Doctoral Dissertations and Master's Theses

Multi-agent systems have become a powerful tool for a wide range of applications due to the effective and cheap solutions they offer. Especially during the last decade, they have impacted a wide array of civilian and military applications (e.g., surveillance, reconnaissance, and payload transportation). However, they suffer system anomalies due to the operational and material conditions, which yields degraded performance or even instability. Hence, this dissertation investigates the distributed adaptive control design process for uncertain multi-agent systems with scalar and high-order dynamics in the presence of unknown control effectiveness and actuator dynamics. First, it provides an approach for driving a …

Initial Orbit Determination Of Uncooperative Satellites Using Particle Swarm Optimization From The Point Of View Of A Novel Observer Orbit, Taylor Yow

Doctoral Dissertations and Master's Theses

Initial orbit determination is an incredibly valuable tool in the field of space situational awareness (SSA). As the number of launches increases every year, more objects are being put into space around the Earth and with political tensions mounting between certain space-accessing countries such as the United States of America (USA), Russia, and China, the number of satellites whose orbits are unknown to a political rival are increasing as well. In this research, orbit estimation of uncooperative target satellites from the point of view of novel orbits using particle swarm optimization (PSO) algorithm is explored. Two cost functions for the …

Analysis And Improvement Of Efficient Charge Recovery Logic Adiabatic Circuits, William Morell

LSU Doctoral Dissertations

Power consumption has been an ever-present concern since the dawn of electronic computing. Every operation that a device performs consumes some amount of energy and as the demand for computation increases, both in scale and ubiquity, reducing this energy loss becomes more important. While modern devices are orders of magnitude more efficient than their ancestors on a per-operation basis, they are increasingly used in more resource constrained applications. Tiny, Internet of Things (IoT) machines are prevalent these days and demanded to perform data collection and analysis at all hours of the day for days at a time on small battery. …

Wireless Power Transfer Using Cavity With Height Discontinuities, Linsheng Zhang

Electrical Engineering Theses and Dissertations

A novel device for efficient wireless power transfer (WPT) system is presented. The proposed WPT system utilizes modified microstrip antennas with height discontinuities (MAHDs) to achieve power transfer. Similar to the conventional WPT system using inductive devices, the power transmission relies on the magnetic field coupling in the near field region. However, the researcher can treat the isolated transmitter or receiver as a modified microstrip antenna, which resembles a capacitive device. Like a capacitive antenna, we can utilize the cavity model, which significantly simplifies field analysis, design and impedance matching process, reduces the overall space requirement, and potentially increases the …

Uav-X Communication: Empirical Characterization And Performance Optimization, Muhammad Hashir Syed

Electrical Engineering Theses and Dissertations

In emerging wireless networks, the scalability of deploying drones presents an opportunity to design extensive aerial networks. These networks could effectively monitor large agricultural fields from the air and soil for food production with efficient resource utilization. On the one hand, unmanned aerial vehicles (UAVs) have gained interest in agricultural aerial inspection due to their ubiquity and observation scale. On the other hand, agricultural internet-of-thing devices, including buried soil sensors, have gained interest in improving natural resource efficiency in crop production. In this work, we investigate the natural interaction of these two phenomena, where UAVs can be leveraged as flying …

Cyber Attacks Against Industrial Control Systems, Adam Kardorff

LSU Master's Theses

Industrial Control Systems (ICS) are the foundation of our critical infrastructure, and allow for the manufacturing of the products we need. These systems monitor and control power plants, water treatment plants, manufacturing plants, and much more. The security of these systems is crucial to our everyday lives and to the safety of those working with ICS. In this thesis we examined how an attacker can take control of these systems using a power plant simulator in the Applied Cybersecurity Lab at LSU. Running experiments on a live environment can be costly and dangerous, so using a simulated environment is the …

Reducing Bias In Cyberbullying Detection With Advanced Llms And Transformer Models, Dahana Moz Ruiz, Annaliese Watson, Anjana Manikandan, Zachary Gordon

Center for Cybersecurity

This paper delved into a comprehensive exploration of the inherent biases present in Large Language Models (LLMs) and various Transformer models, with a focus on their role in identifying and addressing instances of cyberbullying. The objective was to refine and enhance the accuracy and fairness of these models by mitigating the biases deeply ingrained in their structures. This was crucial because language models could inadvertently perpetuate and amplify existing biases present in the data they were trained on.

Inertial Particle Clustering Due To Turbulence In An Air Jet, Bianca Viggiano, Kris Gish, Stephen Solovitz, Raul Bayoan Cal

Mechanical and Materials Engineering Faculty Publications and Presentations

Explosive volcanic eruptions create turbulent plumes of fine ash particles. When these particles collide in the presence of moisture and electrostatic fields they combine into larger aggregates, which can significantly change the atmospheric residence time of the airborne cloud. Previous studies have suggested that turbulence may lead to preferential concentration—also known as clustering—of particles within the flow, increasing the likelihood of collisions and aggregation. Few experimental studies have quantified these processes for volcanic plumes. This behavior was investigated using a particle-laden air jet. By systematically varying the exit speed and the size, density, and concentration of particles, flows were produced …

First-Principles Calculations Of Lattice Thermal Conductivity In Tl,3Vse4: Uncertainties From Different Approaches Of Force Constants, Zhi Li, Yi Xia, Chris Wolverton

Mechanical and Materials Engineering Faculty Publications and Presentations

Accurate and reliable first-principles simulations of lattice thermal conductivity (κL) of highly anharmonic crystals have long been challenging in condensed matter and materials physics. With recent theoretical advances, the calculation of κL has evolved into a sophisticated process requiring the consideration of higher levels of refinements, such as high-order phonon-phonon scattering, anharmonic phonon renormalization, and heat transport beyond the phonon gas picture. Interatomic force constants (IFCs), however, as a shared pillar of the above concepts, are sometimes ambiguously implemented in this process, resulting in non-negligible uncertainties among different studies. Here, we revisit the ultralow κL of Tl3VSe4 and make a …

The Impact Of Government Data Open Platform Construction On Promoting The Development Of Digital Government: An Econometric Analysis Based On Psm Model, Taitian Mao, Tang Gan, Jinliang Chen

Journal of Scientific Information Research

[Purpose/significance]Open government data is the direction of the digital development of government, and exploring the impact of the Open Government Data Platform （OGDP） on the development of digital government is of guiding significance in advancing the goal of modernizing the national governance system and governance capacity. [Method/process]Based on the establishment or not of OGDP, this paper uses the propensity score matching method to investigate the causal relationship between OGDP construction and digital government development by using the cross-sectional data of 101 prefecture-level cities across China in 2019 as the research sample for empirical analysis. [Result/conclusion]Overcoming sample selection bias and eliminating …

Effects Of Confinement On Opposed-Flow Flame Spread Over Cellulose And Polymeric Solids In Microgravity, Ankit Sharma, Yanjun Li, Ya-Ting T. Liao

Student Scholarship

Opposed-flow flame spread over solid materials has been investigated in the past few decades owing to its importance in the fundamental understanding of fires. These studies provided insights into the behavior of opposed-flow flames in different environmental conditions (e.g., flow speed, oxygen concentration). However, the effect of confinement on opposed-flow flames remains under-explored. It is known that confinement plays a critical role in concurrent-flow flame spread in normal and microgravity conditions. Hence, for a complete understanding, it becomes important to understand the effects of confinement for opposed-flow flames. In this study, microgravity experiments are conducted aboard the International Space Station …

Improvement Of Subgrade California Bearing Ratio (Cbr) Using Recycled Concrete Aggregate And Fly Ash, Safkat Tajwar Ahmed, Mozaher Ul Kabir, Chowdhury Zubayer Bin Zahid, Tahsin Tareque, Seyedali Mirmotalebi

Civil Engineering Faculty Publications

The study aims to understand the effect of different admixtures on improving the quality of flexible pavement subgrades. In this paper, recycled concrete aggregates (RCA) and Fly Ash were used as the admixtures in improving the maximum dry density (MDD), swelling potential, and California bearing ratio (CBR) of subgrade soil. The percentages of RCA and fly Ash used were 5%, 10%, and 15%. With the upscaling in fly ash dosage, the optimum moisture content and the California bearing ratio increased. However, the MDD of soil decreased for higher fly ash contents. On the contrary, the optimum moisture content (OMC) of …

04.01.2024 Orsp Connect, Liz Williamson

ORED Newsletter

NSF Conference, Jennifer Baumbaugh, Sustainable Food Packaging research, Export Control Policy Update

Objective.Gg: Uniting Scholastic Esports, Douglas Beirne

Posters - 2024

Objective.gg is a startup recruitment platform within the scholastic esports scene that seeks to unite esports prospects with collegiate esports programs in an effective manner. Objective.gg seeks to accomplish its mission by operating an online platform that allows prospects and collegiate coaches to create their own profiles and connect with one another, building a community in the process. This platform will begin with a free tier, but additional features will be offered through a subscription-based model with two additional pricing tiers to choose from. The online platform will be supported by free online and paid in-person tournaments for Objective.gg platform …

Drivertech Vehicle Monitoring System, Sarah Aldhafeeri, Fillip Cannard, Kaitlyn Ledon, Shea Spellman

Posters - 2024

DriverTech provides critical data to shipping companies about their fleets of vehicles and drivers. This is done through their vehicle monitoring system. Unfortunately, Windows 10 is reaching end of life, and DriverTech is looking for a new software solution.

The Game Of Traffic Lights (Tgotl), Faith Chapman

Posters - 2024

“Computer Science can be applied to nearly ANY field.” In college, and high school especially, the phrase is just that—early comp. sci (CS) students don’t have realworld examples of how/where else they can use CS knowledge outside of CS focused jobs. For high school students, this a missed opportunity to plan for a career outside the obvious. One such career is in traffic lights.

U.S. traffic can be better. Engineering has a subfield dedicated to improving traffic, and part of that entails studying ways to improve traffic lights’ efficacy. Someone with CS knowledge can program a traffic simulator for data …

Use Of Mobile Technology To Identify Behavioral Mechanisms Linked To Mental Health Outcomes In Kenya: Protocol For Development And Validation Of A Predictive Model, Willie Njoroge, Rachel Maina, Frank Elena, Lukoye Atwoli, Anthony Ngugi, Srijan Sen, Stephen Wong, Linda Khakali, Andrew Aballa, James Orwa, Moses Nyongesa, Jasmit Shah, Amina Abubakar, Zul Merali

Brain and Mind Institute

Objective:This study proposes to identify and validate weighted sensor stream signatures that predict near-term risk of a major depressive episode and future mood among healthcare workers in Kenya.

Approach: The study will deploy a mobile application (app) platform and use novel data science analytic approaches (Artificial Intelligence and Machine Learning) to identifying predictors of mental health disorders among 500 randomly sampled healthcare workers from five healthcare facilities in Nairobi, Kenya.

Expectation: This study will lay the basis for creating agile and scalable systems for rapid diagnostics that could inform precise interventions for mitigating depression and ensure a healthy, resilient …

Testing Of Recycled Polypropylene As A Viable Structural Material (Quarter 2), Isabella Jimenez-Melendrez, Katherine Timbes, Jocelyn Embleton, Tauni Dela Cruz, Zyra Kingston, Emily Byrd, Jacob Stinger

Architectural Engineering

5.25 trillion plastic particles have been found in the oceans each year, 3 million water bottles are consumed each hour, and one million plastic bags are used each minute in the United States of America (Williams). The vast majority of conventional plastics such as polyethylene, polypropylene, polystyrene, and more, are non-biodegradable (Tokiwa). To make matters worse, 70% of this non-biodegradable plastic is discarded into landfills and inevitably makes its way into the environment (Williams,). Plastic products have become vital to the United States economy due to their many uses in the construction, packaging, transportation, and health care industries. However, this …

From Visual Data To Auditory Landscapes In Arcgis Pro, Grace Hegland , '24

Senior Theses, Projects, and Awards

Data visualization is a central component to understanding spatial information in ArcGIS Pro. However, visualization creates an accessibility issue for visually impaired users. While ArcGIS supports two screen readers, JAWS and Microsoft Narrator, their ability to convey spatial relationships is limited to reading textual summaries and textual pop ups of spatial data [1]. This Senior Design project explores using data sonification to map ArcGIS data to piano pitches to create an auditory model of visually displayed map data. This auditory model allowed users to find facts and discover geospatial data trends. Ensuring fair access to information is essential for an …

Simple Transit Braking System, Joshua Forde , '24

Senior Theses, Projects, and Awards

A prototype of an automatic braking system for a locomotive was designed and implemented for the purpose of adding an emergency fail safe for trains nationwide. An ultrasonic sensor detected environmental conditions in front of the train, while a connected relay communicated with a servo powered brake to change brake position. An O scale model train was mounted with an onboard sensor, microcontroller, and servo-powered brake to test the effectiveness of an automatic braking system for locomotives. A rubber-like material was used as the brake pad to slow and ideally stop the train on command. Arduino IDE was used to …

Personalized Quiz Maker: Novel Feature For Alby Learning Management System, Lys Kang , '24

Senior Theses, Projects, and Awards

This report details the development of a personalized quiz feature for the Alby learning management platform, designed to enhance student learning by generating quizzes tailored to individual performance data. The project involved creating an algorithm to analyze dynamic student data and identify areas for improvement and then using OpenAI's GPT-4 to generate the multiple choice quizzes with elaborative feedback. Developed as a serverless application with AWS tools, the feature operates independently from the main platform. Despite the absence of applicable professional standards and constraints like limited data availability, the project met its functional requirements, demonstrating the potential to improve educational …

Battery Powered Rice Cooker, Mateo Casalino , '24

Senior Theses, Projects, and Awards

A small low power rice cooker was modified so that its power source came from an external power supply. This allowed the devicet to be remotely operated from a traditional wall socket. A long testing process was carried out to see in-depth information about the current, power, and voltage draw of the rice cooker over an entire cooking and “keep warm” cycle. From this data, the power draw was integrated to find the total energy consumption of the rice cooker and determined what size and type of battery was needed to be purchase. With both the rice cooker and battery …

Shorting At Long Duration: Impact Of Extended Discharge Capacity On Battery Solid Electrolytes, Ryan C. Hill, Amanda S. Peretti, Leo J. Small, Erik D. Spoerke, Yang-Tse Cheng

Chemical and Materials Engineering Faculty Publications

Long-duration energy storage (LDES) is critical to a stable, resilient, and decarbonized electric grid. While batteries are emerging as important LDES devices, extended, high-power discharges necessary for cost-competitive LDES present new materials challenges. Focusing on a new generation of low-temperature molten sodium batteries, we explore here unique phenomena related to long-duration discharge through a well-known solid electrolyte, NaSICON. Specifically, molten sodium symmetric cells at 110 ° C were cycled at 0.1 A cm−2 for 1–23 h discharges. Longer discharges led to unstable overpotentials, reduced resistances, and decreased electrolyte strength, caused by massive sodium penetration not observed in shorter duration discharges. …

Material Modeling Of An Ultraviolet Sensitive Resin At High Pressures And Rates, Truman Miller Russell

Master's Theses (2009 -)

A full understanding of the behavior of binder materials under shock loading is required for effective simulation of heterogeneous polymer-binder-explosives (PBX) and polymer-binder-surrogate (PBS) systems. An accurate simulation is critical for the ultimate goal of designing meso-scale heterogeneous PBS systems. The binder materials studied here is an ultraviolet sensitive resin (UV resin). The UV resin is manufactured by AnyCubic. It is a glassy thermoset polymer and is known to be similar to polymethyl methacrylate (PMMA) both in mechanical properties and in chemical makeup. This material was chosen as it can be additively manufactured, and it will present a lower impedance …

A Study Of The Effect Of Preparation Parameters On The Mechanical Properties Of Freeze-Dried Gelatin-Elastin-Hyaluronate Scaffolds, Mansour Qamash

Master's Theses (2009 -)

This thesis is dedicated to a detailed study of changes in the properties of Gelatin-Elastin-Hyaluronate (GEH) tissue engineering scaffold resulting from changes in preparation parameters. More specifically, utilizing a combination of foaming and freeze-drying techniques, this research investigates the effects of different parameters, including agitation speed, duration time, and chilling temperature on the scaffold’s structural integrity, porosity, and mechanical properties. The methodology involves a carefully calibrated process in which the scaffold matrix is initially prepared by incorporating 8% gelatin, 2% elastin, and 0.5% hyaluronate (w/v) into a homogenous aqueous solution, followed by controlled agitation and subsequent freezing at designated temperatures. …

Investigating The Impacts Of Bin Variability On Particle Size Distributions In Multiphase Eulerian-Eulerian Simulations, Wilbert Alexander Cruz

Master's Theses (2009 -)

In this study, a 3D steady-state Eulerian-Eulerian simulation was developed to investigate flow performance in a dilute pneumatic conveying system. The investigation focused on two main objectives: (1) assessing the influence of bin selection on solution accuracy for representing the polydisperse mixture, and (2) exploring methods to simplify the modeling of polydisperse particles in the simulation by utilizing a mean diameter derived from the mixture’s particle size distribution. The system's geometry and initial boundary conditions featured a 10.6 m long, 150 mm diameter horizontal pipe with both gaseous and solid phases initially moving at 27 m/s . The steady-state simulation …