Engineering Commons^™

Parameters In Ablation Heat Sheilds, Franklin Chang Liang Lin

Masters Theses

"The desired result of this paper is a method of determining temperature distribution and burn off rate in a semi-infinite rod or shield subjected to a large heat flux. The possible methods of determination were investigated, and it was felt that an analytical approach turned out to be the most feasible.

The analytical analysis employed involves the use of the Fourier's general equation for one dimensional heat flow. Transformations from stationary to moving coordinates reduces the problem from unsteady state to steady state boundary conditions. The resulting equations can be applicable to the extent for the heat flow problems involving …

Determining Design Freedom Of Linear Feedback Control Systems, Harley D. Brixey

Masters Theses

“The problem confronted in this thesis is to develop a method or procedure to be used in determining the amount of design freedom that is available in any given linear feedback control system by working with the signal flow-graph representation of the system.

Literature was reviewed that deals with basic signal flow-graph theory and degrees of design freedom. Signal- flow-graph theory that forms a foundation for the development is presented.

The development consists of starting with an essential signal-flow graph of order one. The sensitivity and transmittance functions are written for this essential graph in terms of graph symbols; then …

Impulsive Loading Of Metals And Alloys, William Barnes Mclane

Masters Theses

“This thesis deals with the construction of an explosive deformation apparatus. Using the apparatus an investigation was made of the deformation changes in the structure of a 10% uranium-aluminum alloy and a hot rolled high carbon Manganese steel. Also a study of deformation through different thickness of Stainless Steel, Type-304, plates was carried out.

All of the deformations were obtained using a constant explosive charge consisting of a #6 commercial blasting cap coupled with a commercial chemical booster"--Abstract, page ii.

Thermocouple Shape Influence On Response In A Dynamic Compressible Fluid Atmosphere, Philip J. Steger

Masters Theses

"This investigation was performed to determine whether the geometrical shape of a thermocouple used to measure the temperature of a dynamic fluid atmosphere had any affect on its recovery factor and time response.

A converging nozzle was used to establish a dynamic fluid stream in which shaped silver solder junctions of copper-constantan thermocouples were tested. The velocity of the working fluid, air, was about 1000 ft/sec at the test point.

The investigation was successful, within experimental limits, in determining that the recovery factor of a bare thermocouple junction is not influenced by geometrical shape The results agreed substantially with available …

Interaction Curve For A Beam Column., Mahendra Khushalchand Sanghavi

Masters Theses

"The theoretical interaction curve for a circular section is established. Experimentally the interaction curve f or a beam-column with a varying circular cross section, is established. The effect of stress history is discussed, and the comparisons of different interaction curves are made"--Abstract p.i

The Design, Construction, And Calibration Of An Apparatus To Determine The Thermal Conductivity Of Solids, Alan Edward Stephenson

Masters Theses

"Many pieces of equipment have been designed to determine the thermal conductivity of solids. They all, however, depend on the application of Fourier's equation of heat conduction in solids to determine the thermal conductivity. The apparatus used in this investigation is a modification of the guarded hot plate method used by the American Society for Testing Materials. Operation of the device is given in a step by step procedure both as a guide for others and also to show how it was operated during calibration of the apparatus. Data obtained in the calibration is given in tabular and graphical form …

Derivation Of A Method To Determine Reactions And Deflection Of A Continous Beam On An Elastic Foundation, Louis Richard Fuka

Masters Theses

“The purpose of this thesis is to develop a method for determining the reactions and deflection curve of continuous beams partially supported by an elastic foundation. The method involves representation of an arbitrary loading and the intermediate redundant reactions as Fourier Series. Redundant intermediate reactions are determined by the solution of an equal number of linear equations. The remaining reactions are determined by the application of statics.

This same method can be used for simply supported beams on an elastic foundation and for continuous beams without an elastic foundation”--Abstract, page ii.

Preliminary Investigation Of Acid Treatment For The Stabilization Of Doloma, Deward Pan

Masters Theses

"The work presented in this thesis is the result of an investigation to develop an economical and successful means for producing a stable, hydration resistant compound on the surface of doloma particles by an acid treatment, which does not significantly alter the refractoriness of the material. Granite, a commercial doloma, from Valley Dolomite Corporation, was treated with different concentrations of inorganic acid-water solutions and organic acid-alcohol solutions for varying time at atmospheric pressure and temperature. The treated doloma was examined by (l) X-ray diffraction and (2) the hydration test.

It was found that the organic acid acted as a coating …

The Applicability Of Longwall Mining To American Coal Seams, Mehmet Turgut Tezcanli

Masters Theses

"The objective of this thesis is to show that mechanized longwall mining can be applied to thinner American coal seams with greater advantage than the conventional mechanized room-and-pillar methods now being used, provided that the proper equipment is employed in an effective manner."--Objective, page 1.

An Engineering Evaluation Of Surficial Soils Of Dent County, Missouri, William L. Durham

Masters Theses

“This study is the report of an investigation to: Determine the engineering characteristics of Dent County, Missouri soils using a pedologic soil association map for areal extrapolation of soil test data; and, Evaluate the feasibility of determining the engineering characteristics of all Ozark Region soils by the same method.

During the course of the study, the geology and pedology of the county was investigated and a sampling and testing program formulated. Pedologic soil types in each soil association area were sampled, tested in the laboratory, and the results interpreted.

The results obtained showed that the engineering characteristics of the soil …

The Separation Of Strontium-90 From Cesium-137 And Fractionation Of Rare Earth Elements By Liquid-Liquid Extraction., Surendra D. Khanna

Masters Theses

No abstract provided.

A Study Of Rotational Critical Speed For A Multi-Mass System, Richard K. Brockmann

Masters Theses

"The object of this thesis is to demonstrate, by use of an IBM-1620 digital computer, a fast efficient method for locating natural frequencies of multi-mass rotational systems. Stress and deflection characteristics are examined at these frequencies also.

The shafts considered in this thesis are simply supported and symmetrically loaded with five concentrated masses. These five masses are placed at increments of 10 inches on a 60 inch shaft. The variable to be examined is shaft diameter, which is varied from 0.2 inch to 1 inch by increments of 0.2 inch. The effect of shaft weight, which is a function of …

Experimental Stress Analysis Of Bolts In A Flange Coupling, Bansidhar Shah

Masters Theses

"This thesis deals with the strength of a bolted joint which is subjected to tensile and bending loads. The purpose of this investigation was to derive expressions for the stresses developed in the bolts and the load producing separation of the joint.

A laboratory study of a flange coupling was made and the behaviour of flange bolts under different clamping forces was studied in tension and bending tests. The strain in the bolt was measured by mounting the strain gages on the shank of the bolt. From this, a graph of applied load versus strain in the bolt was plotted. …

A Dilatometric Study Of The Martensite Transformation And Maraging Behavior Of A Ni- Co- Mo Steel, Neal Matthias Griesenauer

Masters Theses

"An experimental investigation or the austenite to martensite transformation and the maraging behavior taking place in a nickel-cobalt-molybdenum steel was conducted for this project.

The austenite to martensite transformation was followed by the dilatometric method, being done on a Leitz Optical Dilatometer. An apparatus was constructed for the dilatometer in order to record dimensional changes at low temperatures, thus broadening the possible applications for the instrument.

The maraging behavior was investigated by means of metallographic analysis and hardness determinations"--Abstract, page i.

A Graphical Solution Method For The Tchebychev Elliptic Function Filter, Gene S. Luckfield

Masters Theses

"This thesis is concerned with the design of the Tchebychev elliptic function filter. The Darlington synthesis procedure is discussed and salient points from Darlington's paper needed for the design of this filter are presented.

It is shown that the design of the Tchebychev elliptic function filter requires a knowledge of the elliptic functions, particularly the elliptic sine. Since the use of these functions is not common, a brief review of their properties is presented.

Using the elliptic functions, a development of the equations describing the behavior of the Tchebychev elliptic function filter is given for the case of a normalized …

A Model Investigation Of The Water Coning Phenomenon., Gary L. Downey

Masters Theses

"Results and procedures are presented covering the design and construction of a dimensionally scaled model of an oil reservoir and its use in investigating the problem of water coning. The theoretical considerations involved in the analytical solution of the water coning problem and the methods used in constructing, designing, and operating the above model are presented.

Four water coning experiments have been completed using the model. Three of the four runs have produced significant results. The information obtained from these experimental results have shown that the laboratory model is well suited for investigating oil reservoir problems such as water coning …

A New Method Of Making Stainless Steel Powder By Electrochemical Disintegration, Mohammed Maher Saad

Masters Theses

"This paper describes a new method of making austenitic stainless steel (18/8) powder by electrochemical disintegration. The method used an external direct current applied to a heat-treated stainless steel anode, and a platinum cathode in an electrolyte of an aqueous solution of 20% HNO₃ and 1% H₂SO₄ by weight respectively.

Special attention has been paid to the size distribution of sieve and sub-sieve sizes, and the following ranges were found: approximately one-half lies between the limits of 200 and 325 mesh, and one third is finer than 325 mesh, with the remainder about +200 mesh, average …

A Rc Active Delay Time Network., Robert Sun-Wu Han

Masters Theses

"This thesis presents a method for performing an approximate synthesis of a variable delay time network by using RC elements and active analog computer circuits. The delay networks discussed here can provide delay times which range from zero to 96 milliseconds for inputs with frequencies which range between zero 2nd 5 cycles per second.

Basically, the procedure involves approximating the delay time transfer function, e^-jwTd , by the ratio of two polynomials each of which is represented by a finite series of terms. The ratio is then shown to be easily synthesized by RC elements and analog computer circuits. …

Evaluation Of Asphalt-Aggregate Distribution In Bituminous Mixes By Autoradiography : Technical Paper, Donald R. Lamb, William Harner Goetz, John E. Christian

JTRP Technical Reports

No abstract provided.

Effects Of Repeated Loading On Gravel And Crushed Stone Base Course Materials Used In The Aasho Road Test, John H. Haynes, Eldon J. Yoder

JTRP Technical Reports

No abstract provided.

Aerial Photography Applied To Traffic Studies : Technical Paper, William F. Howes, Robert Douglas Miles

JTRP Technical Reports

No abstract provided.

Hydrology Of Small Watersheds In Indiana And Hydrodynamics Of Overland Flow, I-Pai Wu

JTRP Technical Reports

No abstract provided.

Factors Affecting The Determination Of Density And Moisture By Nuclear Radiation Techniques : Progress Report, Matthew W. Witczak

JTRP Technical Reports

No abstract provided.

A Study Of Remainder Parcels Resulting From The Acquisition Of Highway Rights-Of-Way, Part 1: Analysis, Vergil G. Stover

JTRP Technical Reports

No abstract provided.

Stress And Deflection In An Elastic Mass Under Semiellipsoidal Loads : Informational Report, John Leonard Sanborn

JTRP Technical Reports

No abstract provided.

Stability Relationships Of Gyratory-Compacted Bituminous Mixtures, Herbert William Busching

JTRP Technical Reports

No abstract provided.

Studies On Tobermorite-Like Calcium Silicate Hydrates : Technical Paper, Sidney Diamond, William Lee Dolch, Joe L. White

JTRP Technical Reports

No abstract provided.

Tobermorite And Tobermorite-Like Calcium Silicate Hydrates: Their Properties And Relationships To Clay Minerals, Sidney Diamond

JTRP Technical Reports

No abstract provided.

An Evaluation Of Intersection Illumination : Technical Paper, John Martin Wright, Joseph C. Oppenlander

JTRP Technical Reports

No abstract provided.

Photogrammetric Analysis Of Traffic Flow Characteristics On Multilane Highways, William F. Howes

JTRP Technical Reports

No abstract provided.